summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2008-09-02Moved initialization of RTL8169 Ethernet controller to board_eth_init()Ben Warren
Affected boards: linkstation r7780mp Removed initialization of the driver from net/eth.c Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-09-02Moved initialization of Ethernet controllers on Atmel AT91 to board_eth_init()Ben Warren
Removed at91sam9_eth_initialize() from net/eth.c Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-09-02Introduce netdev.h header file and remove externsBen Warren
This addresses all drivers whose initializers have already been moved to board_eth_init()/cpu_eth_init(). Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-09-02Add pixis_set_sgmii commandAndy Fleming
The 8544DS and 8572DS platforms support an optional SGMII riser card to expose ethernet over an SGMII interface. Once the card is in, it is also necessary to configure the board such that it uses the card, rather than the on-board ethernet ports. This can either be done by flipping dip switches on the motherboard, or by modifying registers in the pixis. Either way requires a reboot. This adds a command to allow users to choose which ports are routed through the SGMII card, and which through the onboard ports. It also allows users to revert to the current switch settings. This code does not work on the 8572, as the PIXIS is different. Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-09-02Add SGMII support for the 8544 DSAndy Fleming
The 8544 DS has an optional SGMII Riser card, which uses different PHY addresses. Check if we are in SGMII mode, and invoke the SGMII Riser setup code if so. Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-09-02Add support for Freescale SGMII Riser CardAndy Fleming
The 8544DS and 8572DS systems have an optional SGMII riser card which exposes new ethernet ports which are connected to the eTSECs via an SGMII interface. The SGMII PHYs for this board are offset from the standard PHY addresses, so this code modifies the passed in tsec_info structure to use the SGMII PHYs on the card, instead. Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-09-02Add SGMII support to the tsecAndy Fleming
Adds support for configuring the TBI to talk properly with the SerDes. Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-09-02Pass in tsec_info struct through tsec_initializeAndy Fleming
The tsec driver contains a hard-coded array of configuration information for the tsec ethernet controllers. We create a default function that works for most tsecs, and allow that to be overridden by board code. It creates an array of tsec_info structures, which are then parsed by the corresponding driver instance to determine configuration. Also, add regs, miiregs, and devname fields to the tsec_info structure, so that we don't need the kludgy "index" parameter. Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-09-02tsec: Move tsec.h to include/Andy Fleming
This is to prepare the way for board code passing in the tsec_info structure Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-09-02PHY: Add support for the M88E1121R Marvell chip.Sergei Poselenov
Signed-off-by: Yuri Tikhonov <yur@emcraft.com> Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-09-01Merge branch 'Makefile' of git://git.denx.de/u-boot-armWolfgang Denk
2008-09-01Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk
2008-09-01Merge branch 'master' of git://git.denx.de/u-boot-ppc4xxWolfgang Denk
2008-09-01Merge branch 'master' of git://git.denx.de/u-boot-shWolfgang Denk
2008-08-31Merge branch 'master' of git://git.denx.de/u-boot-mpc5xxxWolfgang Denk
2008-08-31sh: Remove CC line from board's MakefileNobuhiro Iwamatsu
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-08-31sh: Replaced "@./mkconfig" for @$(MKCONFIG)Nobuhiro Iwamatsu
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-08-31sh: Add support sh2 to MAKEALLNobuhiro Iwamatsu
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-08-31sh: Fix compile error rsk7203 boardNobuhiro Iwamatsu
This boards used old type preprocessor. This patch fix compile error. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-08-31sh: Fix compile error sh7785lcr boardNobuhiro Iwamatsu
This boards used old type preprocessor. This patch fix compile error. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-08-31sh: Renesas Solutions AP325RXA board supportNobuhiro Iwamatsu
AP325RXA is SH7723's reference board. This has SCIF, NOR Flash, Ethernet, USB host, LCDC, SD Host, Camera and other. In this patch, support SCIF, NOR Flash, and Ethernet. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-08-31sh: add support Renesas SH7723Nobuhiro Iwamatsu
Renesas SH7723 has 5 SCIF, SD, Camera, LCDC and other. This patch supports CPU register's header file and SCIF serial driver. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-08-31sh: Renesas RSK+ 7203 board supportNobuhiro Iwamatsu
This adds initial support for the RTE RSK+ SH7203 board. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-08-31sh: Add support Renesas SH7203 processorNobuhiro Iwamatsu
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-08-31sh: Add support SH2/SH2A which is CPU of Renesas TechnologyNobuhiro Iwamatsu
Add support SH2/SH2A basic function. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-08-31sh: Renesas R0P7785LC0011RL board supportNobuhiro Iwamatsu
This board has SH7785, 512MB DDR2-SDRAM, NOR Flash, Graphic, Ethernet, USB, SD, RTC, and I2C controller. This patch supports the following functions: - 128MB DDR2-SDRAM (29-bit address mode only) - NOR Flash - USB host - Ethernet Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-08-31sh: add support for SH7785Yoshihiro Shimoda
Renesas SH7785 has DDR2-SDRAM controller, PCI, and other. This patch supports CPU register's header file. Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-08-31davinci: fix remaining dm644x_ethJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-31fs: Move conditional compilation to MakefileJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-31devices: merge to list_headJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-31update linux/listJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-31smdk6400: add gitignoreJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-31smdk6400: Use CONFIG_FLASH_CFI_DRIVERJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-31smdk6400: remove redundant bootargs definitionGuennadi Liakhovetski
Double bootargs setting leads to a duplicated environmant entry. Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2008-08-31ARM: Add support for S3C6400 based SMDK6400 boardGuennadi Liakhovetski
SMDK6400 can only boot U-Boot from NAND-flash. This patch adds a nand_spl driver for it too. The board can also boot from the NOR flash, but due to hardware limitations it can only address 64KiB on it, which is not enough for U-Boot. Based on the original sources by Samsung for U-Boot 1.1.6. Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2008-08-31NAND: add NAND driver for S3C64XXGuennadi Liakhovetski
Based on the original S3C64XX NAND driver by Samsung for U-Boot 1.1.6. Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2008-08-31S3C64XX: remove broken HWFLOW support from the serial driverGuennadi Liakhovetski
As noted by Harald Welte, HWFLOW support in the S3C64XX serial driver is broken and currently unused. Remove it. Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2008-08-31serial: add S3C64XX serial driverGuennadi Liakhovetski
Based on the original S3C64XX UART driver by Samsung for U-Boot 1.1.6. Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2008-08-31USB: Add support for OHCI controller on S3C6400Guennadi Liakhovetski
Notice: USB on S3C6400 currently works _only_ with switched off MMU. One could try to enable the MMU, but map addresses 1-to-1, and disable data cache, then it should work too and we could still profit from instruction cache. Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2008-08-31ARM: Add arm1176 core with S3C6400 SoCGuennadi Liakhovetski
Based on the original S3C64XX port by Samsung for U-Boot 1.1.6. Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2008-08-31ARM DaVinci: Changing function names for EMAC driverSandeep Paulraj
DM644x is just one of a series of DaVinci chips that use the EMAC driver. By replacing all the function names that start with dm644x_* to davinci_* we make these function more portable. I have tested this change on my EVM. DM6467 is another DaVinci SOC which uses the EMAC driver and i will be sending patches that add DaVinci DM6467 support to the list soon. Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2008-08-30Integrator[AP/CP] - Remove unused file memsetup.SGururaja Hebbar K R
- memsetup.s is changed/merged to lowlevel_init.S memsetup.S has a global label memsetup that just returns back to caller - memsetup global label is changed/merged to lowlevel_init This label is not called from anywhere. Signed-off-by: Gururaja Hebbar <gururajakr@sanyo.co.in>
2008-08-30ARM DaVinci: Standardize names of directories/filesHugo Villeneuve
ARM DaVinci: Standardize names of directories/files. Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-30ARM DaVinci: Move common functions to board/davinci/commonHugo Villeneuve
ARM DaVinci: Move common functions to board/davinci/common. Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
2008-08-30ppc4xx/NAND: Add select_chip function to 4xx NDFC driverStefan Roese
This function is needed for the new NAND infrastructure. We only need a dummy implementation though for the NDFC. Signed-off-by: Stefan Roese <sr@denx.de>
2008-08-30ppc4xx: Increase image size for NAND boot targetStefan Roese
This is needed since now with HUSH enabled (amcc-common.h) the image read from NAND exceeds the previous limit. Signed-off-by: Stefan Roese <sr@denx.de>
2008-08-29Move MPC512x_FEC driver to drivers/netBen Warren
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-08-29Move MPC5xxx_FEC driver to drivers/netBen Warren
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-08-29cmd_terminal: remove no need ifdefJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-29common/Makefile: order by functionalityJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
generated by cgit v1.2.3 (git 2.0.4) at 2024-11-16 11:16:16 +0000