diff options
Diffstat (limited to 'include')
-rw-r--r-- | include/configs/ap325rxa.h | 1 | ||||
-rw-r--r-- | include/configs/edminiv2.h | 34 | ||||
-rw-r--r-- | include/configs/ms7720se.h | 1 | ||||
-rw-r--r-- | include/configs/openrd_base.h | 31 | ||||
-rw-r--r-- | include/configs/r2dplus.h | 1 | ||||
-rw-r--r-- | include/configs/r7780mp.h | 1 |
6 files changed, 68 insertions, 1 deletions
diff --git a/include/configs/ap325rxa.h b/include/configs/ap325rxa.h index 70dd47ecb56..80a5797493d 100644 --- a/include/configs/ap325rxa.h +++ b/include/configs/ap325rxa.h @@ -138,6 +138,7 @@ #define CONFIG_SYS_ATA_DATA_OFFSET 0x200 /* data reg offset */ #define CONFIG_SYS_ATA_REG_OFFSET 0x200 /* reg offset */ #define CONFIG_SYS_ATA_ALT_OFFSET 0x210 /* alternate register offset */ +#define CONFIG_IDE_SWAP_IO /* if you use all NOR Flash , you change dip-switch. Please see Manual. */ #define CONFIG_SYS_MAX_FLASH_BANKS 1 diff --git a/include/configs/edminiv2.h b/include/configs/edminiv2.h index 055931cda63..57dd1651f36 100644 --- a/include/configs/edminiv2.h +++ b/include/configs/edminiv2.h @@ -60,7 +60,7 @@ #define ORION5X_MPP0_7 0x00000003 #define ORION5X_MPP8_15 0x55550000 -#define ORION5X_MPP16_23 0x00000000 +#define ORION5X_MPP16_23 0x00005555 /* * Board-specific values for Orion5x GPIO low level init: @@ -131,6 +131,7 @@ * Commands configuration - using default command set for now */ #include <config_cmd_default.h> +#define CONFIG_CMD_IDE /* * Network @@ -150,6 +151,37 @@ #endif /* + * IDE + */ +#ifdef CONFIG_CMD_IDE +#define __io +#define CONFIG_IDE_PREINIT +#define CONFIG_DOS_PARTITION +#define CONFIG_CMD_EXT2 +/* ED Mini V has an IDE-compatible SATA connector for port 1 */ +#define CONFIG_MVSATA_IDE +#define CONFIG_MVSATA_IDE_USE_PORT1 +/* Needs byte-swapping for ATA data register */ +#define CONFIG_IDE_SWAP_IO +/* Data, registers and alternate blocks are at the same offset */ +#define CONFIG_SYS_ATA_DATA_OFFSET (0x0100) +#define CONFIG_SYS_ATA_REG_OFFSET (0x0100) +#define CONFIG_SYS_ATA_ALT_OFFSET (0x0100) +/* Each 8-bit ATA register is aligned to a 4-bytes address */ +#define CONFIG_SYS_ATA_STRIDE 4 +/* Controller supports 48-bits LBA addressing */ +#define CONFIG_LBA48 +/* A single bus, a single device */ +#define CONFIG_SYS_IDE_MAXBUS 1 +#define CONFIG_SYS_IDE_MAXDEVICE 1 +/* ATA registers base is at SATA controller base */ +#define CONFIG_SYS_ATA_BASE_ADDR ORION5X_SATA_BASE +/* ATA bus 0 is orion5x port 1 on ED Mini V2 */ +#define CONFIG_SYS_ATA_IDE0_OFFSET ORION5X_SATA_PORT1_OFFSET +/* end of IDE defines */ +#endif /* CMD_IDE */ + +/* * Environment variables configurations */ #define CONFIG_ENV_IS_IN_FLASH 1 diff --git a/include/configs/ms7720se.h b/include/configs/ms7720se.h index ba0a3f8043d..0ea3527e30b 100644 --- a/include/configs/ms7720se.h +++ b/include/configs/ms7720se.h @@ -122,5 +122,6 @@ #define CONFIG_SYS_ATA_DATA_OFFSET 0 /* data reg offset */ #define CONFIG_SYS_ATA_REG_OFFSET 0 /* reg offset */ #define CONFIG_SYS_ATA_ALT_OFFSET 0x200 /* alternate register offset */ +#define CONFIG_IDE_SWAP_IO #endif /* __MS7720SE_H */ diff --git a/include/configs/openrd_base.h b/include/configs/openrd_base.h index 52fa73def92..846dfcd4846 100644 --- a/include/configs/openrd_base.h +++ b/include/configs/openrd_base.h @@ -103,6 +103,7 @@ #define CONFIG_CMD_NAND #define CONFIG_CMD_PING #define CONFIG_CMD_USB +#define CONFIG_CMD_IDE /* * NAND configuration @@ -205,6 +206,36 @@ #endif /* CONFIG_CMD_USB */ /* + * IDe Support on SATA port0 + */ +#ifdef CONFIG_CMD_IDE +#define __io +#define CONFIG_CMD_EXT2 +#define CONFIG_MVSATA_IDE +#define CONFIG_IDE_PREINIT +#define CONFIG_MVSATA_IDE_USE_PORT1 +/* Needs byte-swapping for ATA data register */ +#define CONFIG_IDE_SWAP_IO +/* Data, registers and alternate blocks are at the same offset */ +#define CONFIG_SYS_ATA_DATA_OFFSET (0x0100) +#define CONFIG_SYS_ATA_REG_OFFSET (0x0100) +#define CONFIG_SYS_ATA_ALT_OFFSET (0x0100) +/* Each 8-bit ATA register is aligned to a 4-bytes address */ +#define CONFIG_SYS_ATA_STRIDE 4 +/* Controller supports 48-bits LBA addressing */ +#define CONFIG_LBA48 +/* CONFIG_CMD_IDE requires some #defines for ATA registers */ +#define CONFIG_SYS_IDE_MAXBUS 2 +#define CONFIG_SYS_IDE_MAXDEVICE 2 +/* ATA registers base is at SATA controller base */ +#define CONFIG_SYS_ATA_BASE_ADDR KW_SATA_BASE +/* ATA bus 0 is Kirkwood port 0 on openrd */ +#define CONFIG_SYS_ATA_IDE0_OFFSET KW_SATA_PORT0_OFFSET +/* ATA bus 1 is Kirkwood port 1 on openrd */ +#define CONFIG_SYS_ATA_IDE1_OFFSET KW_SATA_PORT1_OFFSET +#endif /* CONFIG_CMD_IDE */ + +/* * File system */ #define CONFIG_CMD_FAT diff --git a/include/configs/r2dplus.h b/include/configs/r2dplus.h index 8931b974aa2..955f3ff57fe 100644 --- a/include/configs/r2dplus.h +++ b/include/configs/r2dplus.h @@ -96,6 +96,7 @@ #define CONFIG_SYS_ATA_DATA_OFFSET 0x1000 /* data reg offset */ #define CONFIG_SYS_ATA_REG_OFFSET 0x1000 /* reg offset */ #define CONFIG_SYS_ATA_ALT_OFFSET 0x800 /* alternate register offset */ +#define CONFIG_IDE_SWAP_IO /* * SuperH PCI Bridge Configration diff --git a/include/configs/r7780mp.h b/include/configs/r7780mp.h index 71c570eee90..3afe93a6716 100644 --- a/include/configs/r7780mp.h +++ b/include/configs/r7780mp.h @@ -171,6 +171,7 @@ #define CONFIG_SYS_ATA_DATA_OFFSET 0x1000 /* data reg offset */ #define CONFIG_SYS_ATA_REG_OFFSET 0x1000 /* reg offset */ #define CONFIG_SYS_ATA_ALT_OFFSET 0x800 /* alternate register offset */ +#define CONFIG_IDE_SWAP_IO #endif /* CONFIG_CMD_IDE */ #endif /* __R7780RP_H */ |