diff options
Diffstat (limited to 'include')
27 files changed, 247 insertions, 688 deletions
diff --git a/include/configs/ASH405.h b/include/configs/ASH405.h index 9460be3b59..2f5340723d 100644 --- a/include/configs/ASH405.h +++ b/include/configs/ASH405.h @@ -143,6 +143,8 @@ #define CONFIG_SYS_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */ #define CONFIG_SYS_NAND_QUIET 1 +#define CONFIG_SYS_NAND_MAX_OOBFREE 2 +#define CONFIG_SYS_NAND_MAX_ECCPOS 56 /*----------------------------------------------------------------------- * PCI stuff diff --git a/include/configs/C29XPCIE.h b/include/configs/C29XPCIE.h index 08156c531d..bb15745372 100644 --- a/include/configs/C29XPCIE.h +++ b/include/configs/C29XPCIE.h @@ -191,13 +191,14 @@ | CSPR_MSEL_NAND \ | CSPR_V) #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) +#define CONFIG_SYS_NAND_OOBSIZE 0x00000280 /* 640b */ #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ - | CSOR_NAND_RAL_2 /* RAL = 2 Bytes */ \ - | CSOR_NAND_PGS_2K /* Page Size = 2k */ \ - | CSOR_NAND_SPRZ_64 /* Spare size = 64 */ \ - | CSOR_NAND_PB(64)) /* 64 Pages Per Block */ + | CSOR_NAND_RAL_3 /* RAL = 3 Bytes */ \ + | CSOR_NAND_PGS_8K /* Page Size = 8K */ \ + | CSOR_NAND_SPRZ_CSOR_EXT /*oob in csor_ext*/\ + | CSOR_NAND_PB(128)) /*128 Pages Per Block*/ #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x01) | \ FTIM0_NAND_TWP(0x0c) | \ FTIM0_NAND_TWCHT(0x08) | \ @@ -224,6 +225,7 @@ #define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR #define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK #define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR +#define CONFIG_SYS_CSOR1_EXT CONFIG_SYS_NAND_OOBSIZE #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0 #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2 diff --git a/include/configs/MPC8572DS.h b/include/configs/MPC8572DS.h index c7511449ea..9ad94021e4 100644 --- a/include/configs/MPC8572DS.h +++ b/include/configs/MPC8572DS.h @@ -322,6 +322,8 @@ #define CONFIG_CMD_NAND 1 #define CONFIG_NAND_FSL_ELBC 1 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) +#define CONFIG_SYS_NAND_MAX_OOBFREE 5 +#define CONFIG_SYS_NAND_MAX_ECCPOS 56 /* NAND boot: 4K NAND loader config */ #define CONFIG_SYS_NAND_SPL_SIZE 0x1000 diff --git a/include/configs/T4240QDS.h b/include/configs/T4240QDS.h index 3777ccb835..c96df54d99 100644 --- a/include/configs/T4240QDS.h +++ b/include/configs/T4240QDS.h @@ -229,6 +229,8 @@ unsigned long get_board_ddr_clk(void); #define CONFIG_CMD_NAND #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) +#define CONFIG_SYS_NAND_MAX_OOBFREE 2 +#define CONFIG_SYS_NAND_MAX_ECCPOS 256 #if defined(CONFIG_NAND) #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT diff --git a/include/configs/alpr.h b/include/configs/alpr.h index 2bf1986e3a..61fdebac3f 100644 --- a/include/configs/alpr.h +++ b/include/configs/alpr.h @@ -324,6 +324,8 @@ #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE + 0, CONFIG_SYS_NAND_BASE + 2, \ CONFIG_SYS_NAND_BASE + 4, CONFIG_SYS_NAND_BASE + 6 } #define CONFIG_SYS_NAND_QUIET_TEST 1 /* don't warn upon unknown NAND flash */ +#define CONFIG_SYS_NAND_MAX_OOBFREE 2 +#define CONFIG_SYS_NAND_MAX_ECCPOS 56 /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h index f35ed6fba0..d75df92797 100644 --- a/include/configs/am335x_evm.h +++ b/include/configs/am335x_evm.h @@ -220,6 +220,8 @@ #define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/am33xx/u-boot-spl.lds" #ifdef CONFIG_NAND +#define CONFIG_NAND_OMAP_GPMC +#define CONFIG_NAND_OMAP_ELM #define CONFIG_SYS_NAND_5_ADDR_CYCLE #define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \ CONFIG_SYS_NAND_PAGE_SIZE) @@ -237,7 +239,8 @@ #define CONFIG_SYS_NAND_ECCSIZE 512 #define CONFIG_SYS_NAND_ECCBYTES 14 - +#define CONFIG_SYS_NAND_ONFI_DETECTION +#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 #endif diff --git a/include/configs/am335x_igep0033.h b/include/configs/am335x_igep0033.h index 2c69d4e30c..115d1b37c9 100644 --- a/include/configs/am335x_igep0033.h +++ b/include/configs/am335x_igep0033.h @@ -187,6 +187,7 @@ /* NAND support */ #define CONFIG_NAND #define CONFIG_NAND_OMAP_GPMC +#define CONFIG_NAND_OMAP_ELM #define GPMC_NAND_ECC_LP_x16_LAYOUT 1 #define CONFIG_SYS_NAND_BASE (0x08000000) /* phys address CS0 */ #define CONFIG_SYS_MAX_NAND_DEVICE 1 @@ -263,6 +264,7 @@ #define CONFIG_SYS_NAND_ECCSIZE 512 #define CONFIG_SYS_NAND_ECCBYTES 14 +#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE diff --git a/include/configs/am3517_crane.h b/include/configs/am3517_crane.h index 6fd3fb9045..468fb43ea8 100644 --- a/include/configs/am3517_crane.h +++ b/include/configs/am3517_crane.h @@ -340,6 +340,7 @@ 10, 11, 12, 13} #define CONFIG_SYS_NAND_ECCSIZE 512 #define CONFIG_SYS_NAND_ECCBYTES 3 +#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 diff --git a/include/configs/am3517_evm.h b/include/configs/am3517_evm.h index 7e9c55edf1..a3473b51bd 100644 --- a/include/configs/am3517_evm.h +++ b/include/configs/am3517_evm.h @@ -334,6 +334,7 @@ 10, 11, 12, 13} #define CONFIG_SYS_NAND_ECCSIZE 512 #define CONFIG_SYS_NAND_ECCBYTES 3 +#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 diff --git a/include/configs/devkit8000.h b/include/configs/devkit8000.h index 474a5687a9..4f43ba9882 100644 --- a/include/configs/devkit8000.h +++ b/include/configs/devkit8000.h @@ -327,6 +327,7 @@ #define CONFIG_SYS_NAND_ECCSIZE 512 #define CONFIG_SYS_NAND_ECCBYTES 3 +#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE diff --git a/include/configs/mcx.h b/include/configs/mcx.h index a2f7cf711d..dcd29ce7cb 100644 --- a/include/configs/mcx.h +++ b/include/configs/mcx.h @@ -353,7 +353,6 @@ #define CONFIG_SPL_FRAMEWORK #define CONFIG_SPL_BOARD_INIT #define CONFIG_SPL_NAND_SIMPLE -#define CONFIG_SPL_NAND_SOFTECC #define CONFIG_SPL_LIBCOMMON_SUPPORT #define CONFIG_SPL_LIBDISK_SUPPORT @@ -395,6 +394,7 @@ 56, 57, 58, 59, 60, 61, 62, 63} #define CONFIG_SYS_NAND_ECCSIZE 256 #define CONFIG_SYS_NAND_ECCBYTES 3 +#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_SW #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h index bba39d4286..9eab1903ff 100644 --- a/include/configs/omap3_beagle.h +++ b/include/configs/omap3_beagle.h @@ -431,6 +431,7 @@ 10, 11, 12, 13} #define CONFIG_SYS_NAND_ECCSIZE 512 #define CONFIG_SYS_NAND_ECCBYTES 3 +#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 diff --git a/include/configs/omap3_evm.h b/include/configs/omap3_evm.h index 3ace8bb6e5..b7638fb8a6 100644 --- a/include/configs/omap3_evm.h +++ b/include/configs/omap3_evm.h @@ -107,6 +107,7 @@ 10, 11, 12, 13} #define CONFIG_SYS_NAND_ECCSIZE 512 #define CONFIG_SYS_NAND_ECCBYTES 3 +#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 diff --git a/include/configs/omap3_evm_quick_nand.h b/include/configs/omap3_evm_quick_nand.h index 9ecd70d55b..4427e88b7e 100644 --- a/include/configs/omap3_evm_quick_nand.h +++ b/include/configs/omap3_evm_quick_nand.h @@ -86,6 +86,7 @@ 10, 11, 12, 13} #define CONFIG_SYS_NAND_ECCSIZE 512 #define CONFIG_SYS_NAND_ECCBYTES 3 +#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 diff --git a/include/configs/omap3_igep00x0.h b/include/configs/omap3_igep00x0.h index 75d7d70d29..71062a601f 100644 --- a/include/configs/omap3_igep00x0.h +++ b/include/configs/omap3_igep00x0.h @@ -362,6 +362,7 @@ 10, 11, 12, 13} #define CONFIG_SYS_NAND_ECCSIZE 512 #define CONFIG_SYS_NAND_ECCBYTES 3 +#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 #endif diff --git a/include/configs/omap3_overo.h b/include/configs/omap3_overo.h index 84b4aeee2a..e0f026269f 100644 --- a/include/configs/omap3_overo.h +++ b/include/configs/omap3_overo.h @@ -324,6 +324,7 @@ 10, 11, 12, 13} #define CONFIG_SYS_NAND_ECCSIZE 512 #define CONFIG_SYS_NAND_ECCBYTES 3 +#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 diff --git a/include/configs/siemens-am33x-common.h b/include/configs/siemens-am33x-common.h index 745e3bea58..f37653fea3 100644 --- a/include/configs/siemens-am33x-common.h +++ b/include/configs/siemens-am33x-common.h @@ -195,6 +195,7 @@ #define CONFIG_SYS_NAND_ECCSIZE 512 #define CONFIG_SYS_NAND_ECCBYTES 14 +#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW #define CONFIG_SYS_NAND_ECCSTEPS 4 #define CONFIG_SYS_NAND_ECCTOTAL (CONFIG_SYS_NAND_ECCBYTES * \ @@ -430,6 +431,7 @@ "\0" #define CONFIG_NAND_OMAP_GPMC +#define CONFIG_NAND_OMAP_ELM #define GPMC_NAND_ECC_LP_x16_LAYOUT 1 #define CONFIG_SYS_NAND_BASE (0x08000000) /* physical address */ /* to access nand at */ diff --git a/include/configs/spieval.h b/include/configs/spieval.h deleted file mode 100644 index 07668de4d9..0000000000 --- a/include/configs/spieval.h +++ /dev/null @@ -1,494 +0,0 @@ -/* - * (C) Copyright 2003-2005 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * (C) Copyright 2004-2005 - * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */ -#define CONFIG_MPC5200 1 /* (more precisely an MPC5200 CPU) */ -#define CONFIG_TQM5200 1 /* ... on TQM5200 module */ -#undef CONFIG_TQM5200_REV100 /* define for revision 100 modules */ -#define CONFIG_STK52XX 1 /* ... on a STK52XX base board */ -#define CONFIG_STK52XX_REV100 1 /* define for revision 100 baseboards */ - -#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ - -#define CONFIG_HIGH_BATS 1 /* High BATs supported */ - -/* - * Serial console configuration - */ -#define CONFIG_PSC_CONSOLE 6 /* console is on PSC6 */ -#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - -#ifdef CONFIG_STK52XX -#undef CONFIG_PS2KBD /* AT-PS/2 Keyboard */ -#define CONFIG_PS2MULT /* .. on PS/2 Multiplexer */ -#define CONFIG_PS2SERIAL 6 /* .. on PSC6 */ -#define CONFIG_PS2MULT_DELAY (CONFIG_SYS_HZ/2) /* Initial delay */ -#define CONFIG_BOARD_EARLY_INIT_R -#endif /* CONFIG_STK52XX */ - -/* - * PCI Mapping: - * 0x40000000 - 0x4fffffff - PCI Memory - * 0x50000000 - 0x50ffffff - PCI IO Space - */ -#ifdef CONFIG_STK52XX -#define CONFIG_PCI 1 -#define CONFIG_PCI_PNP 1 -/* #define CONFIG_PCI_SCAN_SHOW 1 */ - -#define CONFIG_PCI_MEM_BUS 0x40000000 -#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS -#define CONFIG_PCI_MEM_SIZE 0x10000000 - -#define CONFIG_PCI_IO_BUS 0x50000000 -#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS -#define CONFIG_PCI_IO_SIZE 0x01000000 - -#define CONFIG_EEPRO100 1 -#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ -#define CONFIG_NS8382X 1 -#endif /* CONFIG_STK52XX */ - -/* - * Video console - */ -#if 1 -#define CONFIG_VIDEO -#define CONFIG_VIDEO_SM501 -#define CONFIG_VIDEO_SM501_32BPP -#define CONFIG_CFB_CONSOLE -#define CONFIG_VIDEO_LOGO -#define CONFIG_VGA_AS_SINGLE_DEVICE -#define CONFIG_CONSOLE_EXTRA_INFO -#define CONFIG_VIDEO_SW_CURSOR -#define CONFIG_SPLASH_SCREEN -#define CONFIG_SYS_CONSOLE_IS_IN_ENV -#endif - -/* Partitions */ -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION - -/* USB */ -#ifdef CONFIG_STK52XX -#define CONFIG_USB_OHCI -#define CONFIG_USB_STORAGE -#endif - -/* POST support */ -#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ - CONFIG_SYS_POST_CPU | \ - CONFIG_SYS_POST_I2C) - -#ifdef CONFIG_POST -/* preserve space for the post_word at end of on-chip SRAM */ -#define MPC5XXX_SRAM_POST_SIZE MPC5XXX_SRAM_SIZE-4 -#endif - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_ECHO -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C -#define CONFIG_CMD_MII -#define CONFIG_CMD_NFS -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO -#define CONFIG_CMD_SNTP - -#if defined(CONFIG_MINIFAP) || defined(CONFIG_STK52XX) - #define CONFIG_CMD_IDE - #define CONFIG_CMD_FAT - #define CONFIG_CMD_EXT2 -#endif - -#ifdef CONFIG_STK52XX - #define CONFIG_CMD_USB - #define CONFIG_CMD_FAT -#endif - -#ifdef CONFIG_VIDEO - #define CONFIG_CMD_BMP -#endif - -#ifdef CONFIG_PCI - #define CONFIG_CMD_PCI - #define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 -#endif - -#ifdef CONFIG_POST -#define CONFIG_CMD_DIAG -#endif - - -#define CONFIG_TIMESTAMP /* display image timestamps */ - -#if (CONFIG_SYS_TEXT_BASE == 0xFC000000) /* Boot low */ -# define CONFIG_SYS_LOWBOOT 1 -#endif - -/* - * Autobooting - */ -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "rootpath=/opt/eldk/ppc_6xx\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "flash_self=run ramargs addip;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "flash_nfs=run nfsargs addip;" \ - "bootm ${kernel_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ - "bootfile=/tftpboot/tqm5200/uImage\0" \ - "load=tftp 200000 ${u-boot}\0" \ - "u-boot=/tftpboot/tqm5200/u-boot.bin\0" \ - "update=protect off FC000000 FC05FFFF;" \ - "erase FC000000 FC05FFFF;" \ - "cp.b 200000 FC000000 ${filesize};" \ - "protect on FC000000 FC05FFFF\0" \ - "" - -#define CONFIG_BOOTCOMMAND "run net_nfs" - -/* - * IPB Bus clocking configuration. - */ -#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ - -#if defined(CONFIG_SYS_IPBCLK_EQUALS_XLBCLK) -/* - * PCI Bus clocking configuration - * - * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if - * CONFIG_SYS_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock - * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz. - */ -#define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */ -#endif - -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#ifdef CONFIG_TQM5200_REV100 -#define CONFIG_SYS_I2C_MODULE 1 /* Select I2C module #1 for rev. 100 board */ -#else -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #2 for all other revs */ -#endif - -/* - * I2C clock frequency - * - * Please notice, that the resulting clock frequency could differ from the - * configured value. This is because the I2C clock is derived from system - * clock over a frequency divider with only a few divider values. U-boot - * calculates the best approximation for CONFIG_SYS_I2C_SPEED. However the calculated - * approximation allways lies below the configured value, never above. - */ -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work - * also). For other EEPROMs configuration should be verified. On Mini-FAP the - * EEPROM (24C64) is on the same I2C address (but on other I2C bus), so the - * same configuration could be used. - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20 - -/* - * HW-Monitor configuration on Mini-FAP - */ -#if defined (CONFIG_MINIFAP) -#define CONFIG_SYS_I2C_HWMON_ADDR 0x2C -#endif - -/* List of I2C addresses to be verified by POST */ -#if defined (CONFIG_MINIFAP) -#undef CONFIG_SYS_POST_I2C_ADDRS -#define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_EEPROM_ADDR, \ - CONFIG_SYS_I2C_HWMON_ADDR, \ - CONFIG_SYS_I2C_SLAVE} -#endif - -/* - * Flash configuration - */ -#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_TEXT_BASE /* 0xFC000000 */ - -/* use CFI flash driver if no module variant is spezified */ -#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ -#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_BOOTCS_START } -#define CONFIG_SYS_FLASH_EMPTY_INFO -#define CONFIG_SYS_FLASH_SIZE 0x04000000 /* 64 MByte */ -#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */ -#undef CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* not supported yet for AMD */ - -#if !defined(CONFIG_SYS_LOWBOOT) -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00760000 + 0x00800000) -#else /* CONFIG_SYS_LOWBOOT */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00060000) -#endif /* CONFIG_SYS_LOWBOOT */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks - (= chip selects) */ -#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ - - -/* - * Environment settings - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SIZE 0x10000 -#define CONFIG_ENV_SECT_SIZE 0x20000 -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -/* - * Memory map - */ -#define CONFIG_SYS_MBAR 0xF0000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 - -/* Use ON-Chip SRAM until RAM will be available */ -#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM -#ifdef CONFIG_POST -/* preserve space for the post_word at end of on-chip SRAM */ -#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_POST_SIZE -#else -#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE -#endif - - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -# define CONFIG_SYS_RAMBOOT 1 -#endif - -#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Ethernet configuration - */ -#define CONFIG_MPC5xxx_FEC 1 -/* - * Define CONFIG_FEC_10MBIT to force FEC at 10Mb - */ -/* #define CONFIG_FEC_10MBIT 1 */ -#define CONFIG_PHY_ADDR 0x00 - -/* - * GPIO configuration - * - * use pin gpio_wkup_6 as second SDRAM chip select (mem_cs1): - * Bit 0 (mask: 0x80000000): 1 - * use ALT CAN position: Bits 2-3 (mask: 0x30000000): - * 00 -> No Alternatives, CAN1/2 on PSC2 according to PSC2 setting. - * 01 -> CAN1 on I2C1, CAN2 on Tmr0/1. - * Use for REV200 STK52XX boards. Do not use with REV100 modules - * (because, there I2C1 is used as I2C bus) - * use PSC1 as UART: Bits 28-31 (mask: 0x00000007): 0100 - * use PSC2 as CAN: Bits 25:27 (mask: 0x00000030) - * 000 -> All PSC2 pins are GIOPs - * 001 -> CAN1/2 on PSC2 pins - * Use for REV100 STK52xx boards - * use PSC6: - * on STK52xx: - * use as UART. Pins PSC6_0 to PSC6_3 are used. - * Bits 9:11 (mask: 0x00700000): - * 101 -> PSC6 : Extended POST test is not available - * on MINI-FAP and TQM5200_IB: - * use PSC6_0 to PSC6_3 as GPIO: Bits 9:11 (mask: 0x00700000): - * 000 -> PSC6 could not be used as UART, CODEC or IrDA - * GPIO on PSC6_3 is used in post_hotkeys_pressed() to enable extended POST - * tests. - */ -#if defined (CONFIG_MINIFAP) -# define CONFIG_SYS_GPS_PORT_CONFIG 0x91000004 -#elif defined (CONFIG_STK52XX) -# if defined (CONFIG_STK52XX_REV100) -# define CONFIG_SYS_GPS_PORT_CONFIG 0x81500014 -# else /* STK52xx REV200 and above */ -# if defined (CONFIG_TQM5200_REV100) -# error TQM5200 REV100 not supported on STK52XX REV200 or above -# else/* TQM5200 REV200 and above */ -# define CONFIG_SYS_GPS_PORT_CONFIG 0x91500004 -# endif -# endif -#else /* TMQ5200 Inbetriebnahme-Board */ -# define CONFIG_SYS_GPS_PORT_CONFIG 0x81000004 -#endif - -/* - * RTC configuration - */ -#define CONFIG_RTC_MPC5200 1 /* use internal MPC5200 RTC */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -/* Enable an alternate, more extensive memory test */ -#define CONFIG_SYS_ALT_MEMTEST - -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/* - * Enable loopw command. - */ -#define CONFIG_LOOPW - -/* - * Various low-level settings - */ -#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI -#define CONFIG_SYS_HID0_FINAL HID0_ICE - -#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE -#ifdef CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 -#define CONFIG_SYS_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */ -#else -#define CONFIG_SYS_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */ -#endif -#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE - -#define CONFIG_LAST_STAGE_INIT - -/* - * SRAM - Do not map below 2 GB in address space, because this area is used - * for SDRAM autosizing. - */ -#define CONFIG_SYS_CS2_START 0xE5000000 -#define CONFIG_SYS_CS2_SIZE 0x100000 /* 1 MByte */ -#define CONFIG_SYS_CS2_CFG 0x0004D930 - -/* - * Grafic controller - Do not map below 2 GB in address space, because this - * area is used for SDRAM autosizing. - */ -#define SM501_FB_BASE 0xE0000000 -#define CONFIG_SYS_CS1_START (SM501_FB_BASE) -#define CONFIG_SYS_CS1_SIZE 0x4000000 /* 64 MByte */ -#define CONFIG_SYS_CS1_CFG 0x8F48FF70 -#define SM501_MMIO_BASE CONFIG_SYS_CS1_START + 0x03E00000 - -#define CONFIG_SYS_CS_BURST 0x00000000 -#define CONFIG_SYS_CS_DEADCYCLE 0x33333311 /* 1 dead cycle for flash and SM501 */ - -#define CONFIG_SYS_RESET_ADDRESS 0xff000000 - -/*----------------------------------------------------------------------- - * USB stuff - *----------------------------------------------------------------------- - */ -#define CONFIG_USB_CLOCK 0x0001BBBB -#define CONFIG_USB_CONFIG 0x00001000 - -/*----------------------------------------------------------------------- - * IDE/ATA stuff Supports IDE harddisk - *----------------------------------------------------------------------- - */ - -#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ - -#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ -#undef CONFIG_IDE_LED /* LED for ide not supported */ - -#define CONFIG_IDE_RESET /* reset for ide supported */ -#define CONFIG_IDE_PREINIT - -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ -#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */ - -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 - -#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA - -/* Offset for data I/O */ -#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) - -/* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) - -/* Offset for alternate registers */ -#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) - -/* Interval between registers */ -#define CONFIG_SYS_ATA_STRIDE 4 - -#endif /* __CONFIG_H */ diff --git a/include/configs/tam3517-common.h b/include/configs/tam3517-common.h index 6112c1b7a6..439fc47eb8 100644 --- a/include/configs/tam3517-common.h +++ b/include/configs/tam3517-common.h @@ -224,7 +224,6 @@ #define CONFIG_SPL_BOARD_INIT #define CONFIG_SPL_CONSOLE #define CONFIG_SPL_NAND_SIMPLE -#define CONFIG_SPL_NAND_SOFTECC #define CONFIG_SPL_NAND_WORKSPACE 0x8f07f000 /* below BSS */ #define CONFIG_SPL_LIBCOMMON_SUPPORT @@ -261,6 +260,7 @@ 56, 57, 58, 59, 60, 61, 62, 63} #define CONFIG_SYS_NAND_ECCSIZE 256 #define CONFIG_SYS_NAND_ECCBYTES 3 +#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_SW #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE diff --git a/include/configs/tricorder.h b/include/configs/tricorder.h index afd870762b..cc4001fcd1 100644 --- a/include/configs/tricorder.h +++ b/include/configs/tricorder.h @@ -138,8 +138,9 @@ #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */ /* devices */ -#define CONFIG_NAND_OMAP_BCH8 #define CONFIG_BCH +#define CONFIG_SYS_NAND_MAX_OOBFREE 2 +#define CONFIG_SYS_NAND_MAX_ECCPOS 56 /* commands to include */ #include <config_cmd_default.h> @@ -374,6 +375,7 @@ #define CONFIG_SYS_NAND_ECCSIZE 512 #define CONFIG_SYS_NAND_ECCBYTES 13 +#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW_DETECTION_SW #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE diff --git a/include/fsl_mdio.h b/include/fsl_mdio.h index 9c0b762773..b58713d896 100644 --- a/include/fsl_mdio.h +++ b/include/fsl_mdio.h @@ -1,5 +1,5 @@ /* - * Copyright 2009-2012 Freescale Semiconductor, Inc. + * Copyright 2009-2012, 2013 Freescale Semiconductor, Inc. * Jun-jie Zhang <b18070@freescale.com> * Mingkai Hu <Mingkai.hu@freescale.com> * @@ -31,9 +31,9 @@ #define MIIMIND_BUSY 0x00000001 #define MIIMIND_NOTVALID 0x00000004 -void tsec_local_mdio_write(struct tsec_mii_mng *phyregs, int port_addr, +void tsec_local_mdio_write(struct tsec_mii_mng __iomem *phyregs, int port_addr, int dev_addr, int reg, int value); -int tsec_local_mdio_read(struct tsec_mii_mng *phyregs, int port_addr, +int tsec_local_mdio_read(struct tsec_mii_mng __iomem *phyregs, int port_addr, int dev_addr, int regnum); int tsec_phy_read(struct mii_dev *bus, int addr, int dev_addr, int regnum); int tsec_phy_write(struct mii_dev *bus, int addr, int dev_addr, int regnum, @@ -44,7 +44,7 @@ int memac_mdio_read(struct mii_dev *bus, int port_addr, int dev_addr, int regnum); struct fsl_pq_mdio_info { - struct tsec_mii_mng *regs; + struct tsec_mii_mng __iomem *regs; char *name; }; int fsl_pq_mdio_init(bd_t *bis, struct fsl_pq_mdio_info *info); diff --git a/include/linux/mtd/mtd.h b/include/linux/mtd/mtd.h index 6f44abdc16..a65b681551 100644 --- a/include/linux/mtd/mtd.h +++ b/include/linux/mtd/mtd.h @@ -96,6 +96,29 @@ struct mtd_oob_ops { uint8_t *oobbuf; }; +#ifdef CONFIG_SYS_NAND_MAX_OOBFREE +#define MTD_MAX_OOBFREE_ENTRIES_LARGE CONFIG_SYS_NAND_MAX_OOBFREE +#else +#define MTD_MAX_OOBFREE_ENTRIES_LARGE 32 +#endif + +#ifdef CONFIG_SYS_NAND_MAX_ECCPOS +#define MTD_MAX_ECCPOS_ENTRIES_LARGE CONFIG_SYS_NAND_MAX_ECCPOS +#else +#define MTD_MAX_ECCPOS_ENTRIES_LARGE 640 +#endif + +/* + * ECC layout control structure. Exported to userspace for + * diagnosis and to allow creation of raw images + */ +struct nand_ecclayout { + uint32_t eccbytes; + uint32_t eccpos[MTD_MAX_ECCPOS_ENTRIES_LARGE]; + uint32_t oobavail; + struct nand_oobfree oobfree[MTD_MAX_OOBFREE_ENTRIES_LARGE]; +}; + struct mtd_info { u_char type; u_int32_t flags; diff --git a/include/micrel.h b/include/micrel.h index e1c62d83cb..04c9ecf3bf 100644 --- a/include/micrel.h +++ b/include/micrel.h @@ -15,6 +15,11 @@ #define MII_KSZ9031_MOD_DATA_POST_INC_RW 0x8000 #define MII_KSZ9031_MOD_DATA_POST_INC_W 0xC000 +#define MII_KSZ9031_EXT_RGMII_CTRL_SIG_SKEW 0x4 +#define MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW 0x5 +#define MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW 0x6 +#define MII_KSZ9031_EXT_RGMII_CLOCK_SKEW 0x8 + struct phy_device; int ksz9021_phy_extended_write(struct phy_device *phydev, int regnum, u16 val); int ksz9021_phy_extended_read(struct phy_device *phydev, int regnum); diff --git a/include/mtd/mtd-abi.h b/include/mtd/mtd-abi.h index d51c1abd18..ac3c298760 100644 --- a/include/mtd/mtd-abi.h +++ b/include/mtd/mtd-abi.h @@ -155,18 +155,6 @@ struct nand_oobfree { uint32_t length; }; -#define MTD_MAX_OOBFREE_ENTRIES 8 -/* - * ECC layout control structure. Exported to userspace for - * diagnosis and to allow creation of raw images - */ -struct nand_ecclayout { - uint32_t eccbytes; - uint32_t eccpos[128]; - uint32_t oobavail; - struct nand_oobfree oobfree[MTD_MAX_OOBFREE_ENTRIES]; -}; - /** * struct mtd_ecc_stats - error correction stats * diff --git a/include/net.h b/include/net.h index 5aedc17aa6..0802fad876 100644 --- a/include/net.h +++ b/include/net.h @@ -89,7 +89,7 @@ struct eth_device { int (*recv) (struct eth_device *); void (*halt) (struct eth_device *); #ifdef CONFIG_MCAST_TFTP - int (*mcast) (struct eth_device *, u32 ip, u8 set); + int (*mcast) (struct eth_device *, const u8 *enetaddr, u8 set); #endif int (*write_hwaddr) (struct eth_device *); struct eth_device *next; diff --git a/include/phy.h b/include/phy.h index f0f522a9c2..d3001f1381 100644 --- a/include/phy.h +++ b/include/phy.h @@ -125,6 +125,9 @@ struct phy_driver { /* Called when bringing down the controller */ int (*shutdown)(struct phy_device *phydev); + int (*readext)(struct phy_device *phydev, int addr, int devad, int reg); + int (*writeext)(struct phy_device *phydev, int addr, int devad, int reg, + u16 val); struct list_head list; }; diff --git a/include/tsec.h b/include/tsec.h index f0f3d4d59b..1046426c5c 100644 --- a/include/tsec.h +++ b/include/tsec.h @@ -7,7 +7,7 @@ * terms of the GNU Public License, Version 2, incorporated * herein by reference. * - * Copyright 2004, 2007, 2009, 2011 Freescale Semiconductor, Inc. + * Copyright 2004, 2007, 2009, 2011, 2013 Freescale Semiconductor, Inc. * (C) Copyright 2003, Motorola, Inc. * maintained by Xianghua Xiao (x.xiao@motorola.com) * author Andy Fleming @@ -27,13 +27,26 @@ #define CONFIG_SYS_MDIO_BASE_ADDR (MDIO_BASE_ADDR + 0x520) +#define TSEC_GET_REGS(num, offset) \ + (struct tsec __iomem *)\ + (TSEC_BASE_ADDR + (((num) - 1) * (offset))) + +#define TSEC_GET_REGS_BASE(num) \ + TSEC_GET_REGS((num), TSEC_SIZE) + +#define TSEC_GET_MDIO_REGS(num, offset) \ + (struct tsec_mii_mng __iomem *)\ + (CONFIG_SYS_MDIO_BASE_ADDR + ((num) - 1) * (offset)) + +#define TSEC_GET_MDIO_REGS_BASE(num) \ + TSEC_GET_MDIO_REGS((num), TSEC_MDIO_OFFSET) + #define DEFAULT_MII_NAME "FSL_MDIO" #define STD_TSEC_INFO(num) \ { \ - .regs = (tsec_t *)(TSEC_BASE_ADDR + ((num - 1) * TSEC_SIZE)), \ - .miiregs_sgmii = (struct tsec_mii_mng *)(CONFIG_SYS_MDIO_BASE_ADDR \ - + (num - 1) * TSEC_MDIO_OFFSET), \ + .regs = TSEC_GET_REGS_BASE(num), \ + .miiregs_sgmii = TSEC_GET_MDIO_REGS_BASE(num), \ .devname = CONFIG_TSEC##num##_NAME, \ .phyaddr = TSEC##num##_PHY_ADDR, \ .flags = TSEC##num##_FLAGS, \ @@ -42,9 +55,8 @@ #define SET_STD_TSEC_INFO(x, num) \ { \ - x.regs = (tsec_t *)(TSEC_BASE_ADDR + ((num - 1) * TSEC_SIZE)); \ - x.miiregs_sgmii = (struct tsec_mii_mng *)(CONFIG_SYS_MDIO_BASE_ADDR \ - + (num - 1) * TSEC_MDIO_OFFSET); \ + x.regs = TSEC_GET_REGS_BASE(num); \ + x.miiregs_sgmii = TSEC_GET_MDIO_REGS_BASE(num); \ x.devname = CONFIG_TSEC##num##_NAME; \ x.phyaddr = TSEC##num##_PHY_ADDR; \ x.flags = TSEC##num##_FLAGS;\ @@ -186,195 +198,190 @@ #define RXBD_TRUNCATED 0x0001 #define RXBD_STATS 0x003f -typedef struct txbd8 -{ - ushort status; /* Status Fields */ - ushort length; /* Buffer length */ - uint bufPtr; /* Buffer Pointer */ -} txbd8_t; - -typedef struct rxbd8 -{ - ushort status; /* Status Fields */ - ushort length; /* Buffer Length */ - uint bufPtr; /* Buffer Pointer */ -} rxbd8_t; - -typedef struct rmon_mib -{ +struct txbd8 { + uint16_t status; /* Status Fields */ + uint16_t length; /* Buffer length */ + uint32_t bufptr; /* Buffer Pointer */ +}; + +struct rxbd8 { + uint16_t status; /* Status Fields */ + uint16_t length; /* Buffer Length */ + uint32_t bufptr; /* Buffer Pointer */ +}; + +struct tsec_rmon_mib { /* Transmit and Receive Counters */ - uint tr64; /* Transmit and Receive 64-byte Frame Counter */ - uint tr127; /* Transmit and Receive 65-127 byte Frame Counter */ - uint tr255; /* Transmit and Receive 128-255 byte Frame Counter */ - uint tr511; /* Transmit and Receive 256-511 byte Frame Counter */ - uint tr1k; /* Transmit and Receive 512-1023 byte Frame Counter */ - uint trmax; /* Transmit and Receive 1024-1518 byte Frame Counter */ - uint trmgv; /* Transmit and Receive 1519-1522 byte Good VLAN Frame */ + u32 tr64; /* Tx/Rx 64-byte Frame Counter */ + u32 tr127; /* Tx/Rx 65-127 byte Frame Counter */ + u32 tr255; /* Tx/Rx 128-255 byte Frame Counter */ + u32 tr511; /* Tx/Rx 256-511 byte Frame Counter */ + u32 tr1k; /* Tx/Rx 512-1023 byte Frame Counter */ + u32 trmax; /* Tx/Rx 1024-1518 byte Frame Counter */ + u32 trmgv; /* Tx/Rx 1519-1522 byte Good VLAN Frame */ /* Receive Counters */ - uint rbyt; /* Receive Byte Counter */ - uint rpkt; /* Receive Packet Counter */ - uint rfcs; /* Receive FCS Error Counter */ - uint rmca; /* Receive Multicast Packet (Counter) */ - uint rbca; /* Receive Broadcast Packet */ - uint rxcf; /* Receive Control Frame Packet */ - uint rxpf; /* Receive Pause Frame Packet */ - uint rxuo; /* Receive Unknown OP Code */ - uint raln; /* Receive Alignment Error */ - uint rflr; /* Receive Frame Length Error */ - uint rcde; /* Receive Code Error */ - uint rcse; /* Receive Carrier Sense Error */ - uint rund; /* Receive Undersize Packet */ - uint rovr; /* Receive Oversize Packet */ - uint rfrg; /* Receive Fragments */ - uint rjbr; /* Receive Jabber */ - uint rdrp; /* Receive Drop */ + u32 rbyt; /* Receive Byte Counter */ + u32 rpkt; /* Receive Packet Counter */ + u32 rfcs; /* Receive FCS Error Counter */ + u32 rmca; /* Receive Multicast Packet (Counter) */ + u32 rbca; /* Receive Broadcast Packet */ + u32 rxcf; /* Receive Control Frame Packet */ + u32 rxpf; /* Receive Pause Frame Packet */ + u32 rxuo; /* Receive Unknown OP Code */ + u32 raln; /* Receive Alignment Error */ + u32 rflr; /* Receive Frame Length Error */ + u32 rcde; /* Receive Code Error */ + u32 rcse; /* Receive Carrier Sense Error */ + u32 rund; /* Receive Undersize Packet */ + u32 rovr; /* Receive Oversize Packet */ + u32 rfrg; /* Receive Fragments */ + u32 rjbr; /* Receive Jabber */ + u32 rdrp; /* Receive Drop */ /* Transmit Counters */ - uint tbyt; /* Transmit Byte Counter */ - uint tpkt; /* Transmit Packet */ - uint tmca; /* Transmit Multicast Packet */ - uint tbca; /* Transmit Broadcast Packet */ - uint txpf; /* Transmit Pause Control Frame */ - uint tdfr; /* Transmit Deferral Packet */ - uint tedf; /* Transmit Excessive Deferral Packet */ - uint tscl; /* Transmit Single Collision Packet */ + u32 tbyt; /* Transmit Byte Counter */ + u32 tpkt; /* Transmit Packet */ + u32 tmca; /* Transmit Multicast Packet */ + u32 tbca; /* Transmit Broadcast Packet */ + u32 txpf; /* Transmit Pause Control Frame */ + u32 tdfr; /* Transmit Deferral Packet */ + u32 tedf; /* Transmit Excessive Deferral Packet */ + u32 tscl; /* Transmit Single Collision Packet */ /* (0x2_n700) */ - uint tmcl; /* Transmit Multiple Collision Packet */ - uint tlcl; /* Transmit Late Collision Packet */ - uint txcl; /* Transmit Excessive Collision Packet */ - uint tncl; /* Transmit Total Collision */ - - uint res2; - - uint tdrp; /* Transmit Drop Frame */ - uint tjbr; /* Transmit Jabber Frame */ - uint tfcs; /* Transmit FCS Error */ - uint txcf; /* Transmit Control Frame */ - uint tovr; /* Transmit Oversize Frame */ - uint tund; /* Transmit Undersize Frame */ - uint tfrg; /* Transmit Fragments Frame */ + u32 tmcl; /* Transmit Multiple Collision Packet */ + u32 tlcl; /* Transmit Late Collision Packet */ + u32 txcl; /* Transmit Excessive Collision Packet */ + u32 tncl; /* Transmit Total Collision */ + + u32 res2; + + u32 tdrp; /* Transmit Drop Frame */ + u32 tjbr; /* Transmit Jabber Frame */ + u32 tfcs; /* Transmit FCS Error */ + u32 txcf; /* Transmit Control Frame */ + u32 tovr; /* Transmit Oversize Frame */ + u32 tund; /* Transmit Undersize Frame */ + u32 tfrg; /* Transmit Fragments Frame */ /* General Registers */ - uint car1; /* Carry Register One */ - uint car2; /* Carry Register Two */ - uint cam1; /* Carry Register One Mask */ - uint cam2; /* Carry Register Two Mask */ -} rmon_mib_t; - -typedef struct tsec_hash_regs -{ - uint iaddr0; /* Individual Address Register 0 */ - uint iaddr1; /* Individual Address Register 1 */ - uint iaddr2; /* Individual Address Register 2 */ - uint iaddr3; /* Individual Address Register 3 */ - uint iaddr4; /* Individual Address Register 4 */ - uint iaddr5; /* Individual Address Register 5 */ - uint iaddr6; /* Individual Address Register 6 */ - uint iaddr7; /* Individual Address Register 7 */ - uint res1[24]; - uint gaddr0; /* Group Address Register 0 */ - uint gaddr1; /* Group Address Register 1 */ - uint gaddr2; /* Group Address Register 2 */ - uint gaddr3; /* Group Address Register 3 */ - uint gaddr4; /* Group Address Register 4 */ - uint gaddr5; /* Group Address Register 5 */ - uint gaddr6; /* Group Address Register 6 */ - uint gaddr7; /* Group Address Register 7 */ - uint res2[24]; -} tsec_hash_t; - -typedef struct tsec -{ + u32 car1; /* Carry Register One */ + u32 car2; /* Carry Register Two */ + u32 cam1; /* Carry Register One Mask */ + u32 cam2; /* Carry Register Two Mask */ +}; + +struct tsec_hash_regs { + u32 iaddr0; /* Individual Address Register 0 */ + u32 iaddr1; /* Individual Address Register 1 */ + u32 iaddr2; /* Individual Address Register 2 */ + u32 iaddr3; /* Individual Address Register 3 */ + u32 iaddr4; /* Individual Address Register 4 */ + u32 iaddr5; /* Individual Address Register 5 */ + u32 iaddr6; /* Individual Address Register 6 */ + u32 iaddr7; /* Individual Address Register 7 */ + u32 res1[24]; + u32 gaddr0; /* Group Address Register 0 */ + u32 gaddr1; /* Group Address Register 1 */ + u32 gaddr2; /* Group Address Register 2 */ + u32 gaddr3; /* Group Address Register 3 */ + u32 gaddr4; /* Group Address Register 4 */ + u32 gaddr5; /* Group Address Register 5 */ + u32 gaddr6; /* Group Address Register 6 */ + u32 gaddr7; /* Group Address Register 7 */ + u32 res2[24]; +}; + +struct tsec { /* General Control and Status Registers (0x2_n000) */ - uint res000[4]; + u32 res000[4]; - uint ievent; /* Interrupt Event */ - uint imask; /* Interrupt Mask */ - uint edis; /* Error Disabled */ - uint res01c; - uint ecntrl; /* Ethernet Control */ - uint minflr; /* Minimum Frame Length */ - uint ptv; /* Pause Time Value */ - uint dmactrl; /* DMA Control */ - uint tbipa; /* TBI PHY Address */ + u32 ievent; /* Interrupt Event */ + u32 imask; /* Interrupt Mask */ + u32 edis; /* Error Disabled */ + u32 res01c; + u32 ecntrl; /* Ethernet Control */ + u32 minflr; /* Minimum Frame Length */ + u32 ptv; /* Pause Time Value */ + u32 dmactrl; /* DMA Control */ + u32 tbipa; /* TBI PHY Address */ - uint res034[3]; - uint res040[48]; + u32 res034[3]; + u32 res040[48]; /* Transmit Control and Status Registers (0x2_n100) */ - uint tctrl; /* Transmit Control */ - uint tstat; /* Transmit Status */ - uint res108; - uint tbdlen; /* Tx BD Data Length */ - uint res110[5]; - uint ctbptr; /* Current TxBD Pointer */ - uint res128[23]; - uint tbptr; /* TxBD Pointer */ - uint res188[30]; + u32 tctrl; /* Transmit Control */ + u32 tstat; /* Transmit Status */ + u32 res108; + u32 tbdlen; /* Tx BD Data Length */ + u32 res110[5]; + u32 ctbptr; /* Current TxBD Pointer */ + u32 res128[23]; + u32 tbptr; /* TxBD Pointer */ + u32 res188[30]; /* (0x2_n200) */ - uint res200; - uint tbase; /* TxBD Base Address */ - uint res208[42]; - uint ostbd; /* Out of Sequence TxBD */ - uint ostbdp; /* Out of Sequence Tx Data Buffer Pointer */ - uint res2b8[18]; + u32 res200; + u32 tbase; /* TxBD Base Address */ + u32 res208[42]; + u32 ostbd; /* Out of Sequence TxBD */ + u32 ostbdp; /* Out of Sequence Tx Data Buffer Pointer */ + u32 res2b8[18]; /* Receive Control and Status Registers (0x2_n300) */ - uint rctrl; /* Receive Control */ - uint rstat; /* Receive Status */ - uint res308; - uint rbdlen; /* RxBD Data Length */ - uint res310[4]; - uint res320; - uint crbptr; /* Current Receive Buffer Pointer */ - uint res328[6]; - uint mrblr; /* Maximum Receive Buffer Length */ - uint res344[16]; - uint rbptr; /* RxBD Pointer */ - uint res388[30]; + u32 rctrl; /* Receive Control */ + u32 rstat; /* Receive Status */ + u32 res308; + u32 rbdlen; /* RxBD Data Length */ + u32 res310[4]; + u32 res320; + u32 crbptr; /* Current Receive Buffer Pointer */ + u32 res328[6]; + u32 mrblr; /* Maximum Receive Buffer Length */ + u32 res344[16]; + u32 rbptr; /* RxBD Pointer */ + u32 res388[30]; /* (0x2_n400) */ - uint res400; - uint rbase; /* RxBD Base Address */ - uint res408[62]; + u32 res400; + u32 rbase; /* RxBD Base Address */ + u32 res408[62]; /* MAC Registers (0x2_n500) */ - uint maccfg1; /* MAC Configuration #1 */ - uint maccfg2; /* MAC Configuration #2 */ - uint ipgifg; /* Inter Packet Gap/Inter Frame Gap */ - uint hafdup; /* Half-duplex */ - uint maxfrm; /* Maximum Frame */ - uint res514; - uint res518; + u32 maccfg1; /* MAC Configuration #1 */ + u32 maccfg2; /* MAC Configuration #2 */ + u32 ipgifg; /* Inter Packet Gap/Inter Frame Gap */ + u32 hafdup; /* Half-duplex */ + u32 maxfrm; /* Maximum Frame */ + u32 res514; + u32 res518; - uint res51c; + u32 res51c; - uint resmdio[6]; + u32 resmdio[6]; - uint res538; + u32 res538; - uint ifstat; /* Interface Status */ - uint macstnaddr1; /* Station Address, part 1 */ - uint macstnaddr2; /* Station Address, part 2 */ - uint res548[46]; + u32 ifstat; /* Interface Status */ + u32 macstnaddr1; /* Station Address, part 1 */ + u32 macstnaddr2; /* Station Address, part 2 */ + u32 res548[46]; /* (0x2_n600) */ - uint res600[32]; + u32 res600[32]; /* RMON MIB Registers (0x2_n680-0x2_n73c) */ - rmon_mib_t rmon; - uint res740[48]; + struct tsec_rmon_mib rmon; + u32 res740[48]; /* Hash Function Registers (0x2_n800) */ - tsec_hash_t hash; + struct tsec_hash_regs hash; - uint res900[128]; + u32 res900[128]; /* Pattern Registers (0x2_nb00) */ - uint resb00[62]; - uint attr; /* Default Attribute Register */ - uint attreli; /* Default Attribute Extract Length and Index */ + u32 resb00[62]; + u32 attr; /* Default Attribute Register */ + u32 attreli; /* Default Attribute Extract Length and Index */ /* TSEC Future Expansion Space (0x2_nc00-0x2_nffc) */ - uint resc00[256]; -} tsec_t; + u32 resc00[256]; +}; #define TSEC_GIGABIT (1 << 0) @@ -383,8 +390,8 @@ typedef struct tsec #define TSEC_SGMII (1 << 2) /* MAC-PHY interface uses SGMII */ struct tsec_private { - tsec_t *regs; - struct tsec_mii_mng *phyregs_sgmii; + struct tsec __iomem *regs; + struct tsec_mii_mng __iomem *phyregs_sgmii; struct phy_device *phydev; phy_interface_t interface; struct mii_dev *bus; @@ -394,8 +401,8 @@ struct tsec_private { }; struct tsec_info_struct { - tsec_t *regs; - struct tsec_mii_mng *miiregs_sgmii; + struct tsec __iomem *regs; + struct tsec_mii_mng __iomem *miiregs_sgmii; char *devname; char *mii_devname; phy_interface_t interface; |