diff options
Diffstat (limited to 'include/configs')
-rw-r--r-- | include/configs/MVBLUE.h | 325 |
1 files changed, 325 insertions, 0 deletions
diff --git a/include/configs/MVBLUE.h b/include/configs/MVBLUE.h new file mode 100644 index 00000000000..6965e1cdb7b --- /dev/null +++ b/include/configs/MVBLUE.h @@ -0,0 +1,325 @@ +/* + * (C) Copyright 2001 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define MV_VERSION "v0.2.0" + +/* LED0 = Power , LED1 = Error , LED2-5 = error code, LED6-7=00 -->PPCBoot error */ +#define ERR_NONE 0 +#define ERR_ENV 1 +#define ERR_BOOTM_BADMAGIC 2 +#define ERR_BOOTM_BADCRC 3 +#define ERR_BOOTM_GUNZIP 4 +#define ERR_BOOTP_TIMEOUT 5 +#define ERR_DHCP 6 +#define ERR_TFTP 7 +#define ERR_NOLAN 8 +#define ERR_LANDRV 9 + +#define CONFIG_BOARD_TYPES 1 +#define MVBLUE_BOARD_BOX 1 +#define MVBLUE_BOARD_LYNX 2 + +#if 0 +#define ERR_LED(code) do { if (code) \ + *(volatile char *)(0xff000003) = ( 3 | (code<<4) ) & 0xf3; \ + else \ + *(volatile char *)(0xff000003) = ( 1 ); \ + } while(0) +#else +#define ERR_LED(code) +#endif + +#undef DEBUG + +#define CONFIG_MPC824X 1 +#define CONFIG_MPC8245 1 +#define CONFIG_MVBLUE 1 + +#define CONFIG_CLOCKS_IN_MHZ 1 + +#define CONFIG_BOARD_TYPES 1 + +#define CONFIG_CONS_INDEX 1 +#define CONFIG_BAUDRATE 115200 +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +#define CONFIG_BOOTDELAY 3 +#define CONFIG_BOOT_RETRY_TIME -1 + +#define CONFIG_AUTOBOOT_KEYED +#define CONFIG_AUTOBOOT_PROMPT "autoboot in %d seconds (stop with 's')...\n\0" +#define CONFIG_AUTOBOOT_STOP_STR "s\0" +#define CONFIG_ZERO_BOOTDELAY_CHECK +#define CONFIG_RESET_TO_RETRY 60 + +#define CONFIG_COMMANDS ( CFG_CMD_ASKENV | CFG_CMD_BOOTD | CFG_CMD_CACHE | CFG_CMD_DHCP | \ + CFG_CMD_ECHO | CFG_CMD_ENV | CFG_CMD_FLASH | CFG_CMD_IMI | \ + CFG_CMD_IRQ | CFG_CMD_NET | CFG_CMD_PCI | CFG_CMD_RUN ) + + +#define CONFIG_BOOTP_MASK ( 0xffffffff ) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ + +#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) +#define CFG_MAXARGS 16 /* Max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_LOAD_ADDR 0x00100000 /* Default load address */ + +#define CONFIG_BOOTCOMMAND "run nfsboot" +#define CONFIG_BOOTARGS "root=/dev/mtdblock5 ro rootfstype=jffs2" + +#define CONFIG_NFSBOOTCOMMAND "bootp; run nfsargs addcons;bootm" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "console_nr=0\0" \ + "dhcp_client_id=mvBOX-XP\0" \ + "dhcp_vendor-class-identifier=mvBOX\0" \ + "adminboot=setenv bootargs root=/dev/mtdblock5 rw rootfstype=jffs2;run addcons;bootm ffc00000\0" \ + "flashboot=setenv bootargs root=/dev/mtdblock5 ro rootfstype=jffs2;run addcons;bootm ffc00000\0" \ + "safeboot=setenv bootargs root=/dev/mtdblock2 rw rootfstype=cramfs;run addcons;bootm ffc00000\0" \ + "hdboot=setenv bootargs root=/dev/hda1;run addcons;bootm ffc00000\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off\0" \ + "addcons=setenv bootargs $(bootargs) console=ttyS$(console_nr),$(baudrate)N8\0" \ + "mv_version=" MV_VERSION "\0" \ + "bootretry=30\0" + +#define CONFIG_OVERWRITE_ETHADDR_ONCE + +/*----------------------------------------------------------------------- + * PCI stuff + *----------------------------------------------------------------------- + */ + +#define CONFIG_PCI +#define CONFIG_PCI_PNP +#define CONFIG_PCI_SCAN_SHOW + +#define CONFIG_NET_MULTI +#define CONFIG_NET_RETRY_COUNT 5 + +#define CONFIG_TULIP +#define CONFIG_TULIP_FIX_DAVICOM 1 +#define CONFIG_ETHADDR b6:b4:45:eb:fb:c0 + +#define CONFIG_HW_WATCHDOG + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 + +#define CFG_FLASH_BASE 0xFFF00000 +#define CFG_MONITOR_BASE TEXT_BASE + +#define CFG_RESET_ADDRESS 0xFFF00100 +#define CFG_EUMB_ADDR 0xFC000000 + +#define CFG_MONITOR_LEN 0x00100000 +#define CFG_MALLOC_LEN (512 << 10) /* Reserve some kB for malloc() */ + +#define CFG_MEMTEST_START 0x00100000 /* memtest works on */ +#define CFG_MEMTEST_END 0x00800000 /* 1M ... 8M in DRAM */ + +/* Maximum amount of RAM. */ +#define CFG_MAX_RAM_SIZE 0x10000000 /* 0 .. 256MB of (S)DRAM */ + + +#if CFG_MONITOR_BASE >= CFG_FLASH_BASE +#undef CFG_RAMBOOT +#else +#define CFG_RAMBOOT +#endif + +#define CFG_ISA_IO 0xFE000000 + +/* + * serial configuration + */ +#define CFG_NS16550 +#define CFG_NS16550_SERIAL + +#define CFG_NS16550_REG_SIZE 1 + +#define CFG_NS16550_CLK get_bus_freq(0) + +#define CFG_NS16550_COM1 (CFG_EUMB_ADDR + 0x4500) +#define CFG_NS16550_COM2 (CFG_EUMB_ADDR + 0x4600) + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area + */ +#define CFG_INIT_RAM_ADDR 0x40000000 +#define CFG_INIT_RAM_END 0x1000 +#define CFG_GBL_DATA_SIZE 128 +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + * For the detail description refer to the MPC8240 user's manual. + */ + +#define CONFIG_SYS_CLK_FREQ 33000000 +#define CFG_HZ 10000 + +/* Bit-field values for MCCR1. */ +#define CFG_ROMNAL 7 +#define CFG_ROMFAL 11 + +/* Bit-field values for MCCR2. */ +#define CFG_TSWAIT 0x5 +#define CFG_REFINT 430 + +/* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4. */ +#define CFG_BSTOPRE 121 + +/* Bit-field values for MCCR3. */ +#define CFG_REFREC 8 + +/* Bit-field values for MCCR4. */ +#define CFG_PRETOACT 3 +#define CFG_ACTTOPRE 5 +#define CFG_ACTORW 3 +#define CFG_SDMODE_CAS_LAT 3 +#define CFG_REGISTERD_TYPE_BUFFER 1 +#define CFG_EXTROM 1 +#define CFG_REGDIMM 0 +#define CFG_DBUS_SIZE2 1 +#define CFG_SDMODE_WRAP 0 + +#define CFG_PGMAX 0x32 +#define CFG_SDRAM_DSCD 0x20 + +/* Memory bank settings. + * Only bits 20-29 are actually used from these vales to set the + * start/end addresses. The upper two bits will always be 0, and the lower + * 20 bits will be 0x00000 for a start address, or 0xfffff for an end + * address. Refer to the MPC8240 book. + */ + +#define CFG_BANK0_START 0x00000000 +#define CFG_BANK0_END (CFG_MAX_RAM_SIZE - 1) +#define CFG_BANK0_ENABLE 1 +#define CFG_BANK1_START 0x3ff00000 +#define CFG_BANK1_END 0x3fffffff +#define CFG_BANK1_ENABLE 0 +#define CFG_BANK2_START 0x3ff00000 +#define CFG_BANK2_END 0x3fffffff +#define CFG_BANK2_ENABLE 0 +#define CFG_BANK3_START 0x3ff00000 +#define CFG_BANK3_END 0x3fffffff +#define CFG_BANK3_ENABLE 0 +#define CFG_BANK4_START 0x3ff00000 +#define CFG_BANK4_END 0x3fffffff +#define CFG_BANK4_ENABLE 0 +#define CFG_BANK5_START 0x3ff00000 +#define CFG_BANK5_END 0x3fffffff +#define CFG_BANK5_ENABLE 0 +#define CFG_BANK6_START 0x3ff00000 +#define CFG_BANK6_END 0x3fffffff +#define CFG_BANK6_ENABLE 0 +#define CFG_BANK7_START 0x3ff00000 +#define CFG_BANK7_END 0x3fffffff +#define CFG_BANK7_ENABLE 0 + +#define CFG_ODCR 0xff + +#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) + +#define CFG_IBAT1L (CFG_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT1U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) + +#define CFG_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT) +#define CFG_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP) + +#define CFG_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT) +#define CFG_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP) + +#define CFG_DBAT0L CFG_IBAT0L +#define CFG_DBAT0U CFG_IBAT0U +#define CFG_DBAT1L CFG_IBAT1L +#define CFG_DBAT1U CFG_IBAT1U +#define CFG_DBAT2L CFG_IBAT2L +#define CFG_DBAT2U CFG_IBAT2U +#define CFG_DBAT3L CFG_IBAT3L +#define CFG_DBAT3U CFG_IBAT3U + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#undef CFG_FLASH_PROTECTION +#define CFG_MAX_FLASH_BANKS 1 /* Max number of flash banks */ +#define CFG_MAX_FLASH_SECT 63 /* Max number of sectors per flash */ + +#define CFG_FLASH_ERASE_TOUT 12000 +#define CFG_FLASH_WRITE_TOUT 1000 + + +#define CFG_ENV_IS_IN_FLASH + +#define CFG_ENV_OFFSET 0x00010000 +#define CFG_ENV_SIZE 0x00010000 +#define CFG_ENV_SECT_SIZE 0x00010000 + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 32 +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#endif /* __CONFIG_H */ |