diff options
Diffstat (limited to 'include/configs/yosemite.h')
| -rw-r--r-- | include/configs/yosemite.h | 216 |
1 files changed, 0 insertions, 216 deletions
diff --git a/include/configs/yosemite.h b/include/configs/yosemite.h deleted file mode 100644 index d9c09b80cd..0000000000 --- a/include/configs/yosemite.h +++ /dev/null @@ -1,216 +0,0 @@ -/* - * (C) Copyright 2005-2007 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/************************************************************************ - * yosemite.h - configuration for Yosemite & Yellowstone boards - ***********************************************************************/ -#ifndef __CONFIG_H -#define __CONFIG_H - -/*----------------------------------------------------------------------- - * High Level Configuration Options - *----------------------------------------------------------------------*/ -/* This config file is used for Yosemite (440EP) and Yellowstone (440GR)*/ -#ifndef CONFIG_YELLOWSTONE -#define CONFIG_440EP 1 /* Specific PPC440EP support */ -#define CONFIG_HOSTNAME yosemite -#else -#define CONFIG_440GR 1 /* Specific PPC440GR support */ -#define CONFIG_HOSTNAME yellowstone -#endif -#define CONFIG_440 1 /* ... PPC440 family */ -#define CONFIG_SYS_CLK_FREQ 66666666 /* external freq to pll */ - -#define CONFIG_SYS_TEXT_BASE 0xFFF80000 - -/* - * Include common defines/options for all AMCC eval boards - */ -#include "amcc-common.h" - -#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ -#define CONFIG_BOARD_RESET 1 /* call board_reset() */ - -/*----------------------------------------------------------------------- - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_FLASH_BASE 0xfc000000 /* start of FLASH */ -#define CONFIG_SYS_PCI_MEMBASE 0xa0000000 /* mapped pci memory*/ -#define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000 -#define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000 -#define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000 - -/*Don't change either of these*/ -#define CONFIG_SYS_PCI_BASE 0xe0000000 /* internal PCI regs*/ -/*Don't change either of these*/ - -#define CONFIG_SYS_USB_DEVICE 0x50000000 -#define CONFIG_SYS_NVRAM_BASE_ADDR 0x80000000 -#define CONFIG_SYS_BCSR_BASE (CONFIG_SYS_NVRAM_BASE_ADDR | 0x2000) -#define CONFIG_SYS_BOOT_BASE_ADDR 0xf0000000 - -/*----------------------------------------------------------------------- - * Initial RAM & stack pointer (placed in SDRAM) - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_INIT_RAM_DCACHE 1 /* d-cache as init ram */ -#define CONFIG_SYS_INIT_RAM_ADDR 0x70000000 /* DCache */ -#define CONFIG_SYS_INIT_RAM_SIZE (4 << 10) -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Serial Port - *----------------------------------------------------------------------*/ -#define CONFIG_CONS_INDEX 1 /* Use UART0 */ -#define CONFIG_SYS_EXT_SERIAL_CLOCK 11059200 /* use external 11.059MHz clk */ - -/*----------------------------------------------------------------------- - * Environment - *----------------------------------------------------------------------*/ -/* - * Define here the location of the environment variables (FLASH or EEPROM). - * Note: DENX encourages to use redundant environment in FLASH. - */ -#if 1 -#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ -#else -#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ -#endif - -/*----------------------------------------------------------------------- - * FLASH related - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ -#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ -#define CONFIG_SYS_FLASH_CFI_AMD_RESET 1 /* AMD RESET for STM 29W320DB! */ - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ - -#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ - -#ifdef CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) -#endif /* CONFIG_ENV_IS_IN_FLASH */ - -/*----------------------------------------------------------------------- - * DDR SDRAM - *----------------------------------------------------------------------*/ -#undef CONFIG_SPD_EEPROM /* Don't use SPD EEPROM for setup */ -#define CONFIG_SYS_KBYTES_SDRAM (128 * 1024) /* 128MB */ -#define CONFIG_SYS_SDRAM_BANKS (2) - -/*----------------------------------------------------------------------- - * I2C - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 - -#define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1) -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 - -#ifdef CONFIG_ENV_IS_IN_EEPROM -#define CONFIG_ENV_SIZE 0x200 /* Size of Environment vars */ -#define CONFIG_ENV_OFFSET 0x0 -#endif /* CONFIG_ENV_IS_IN_EEPROM */ - -/* - * Default environment variables - */ -#define CONFIG_EXTRA_ENV_SETTINGS \ - CONFIG_AMCC_DEF_ENV \ - CONFIG_AMCC_DEF_ENV_POWERPC \ - CONFIG_AMCC_DEF_ENV_PPC_OLD \ - CONFIG_AMCC_DEF_ENV_NOR_UPD \ - "kernel_addr=fc000000\0" \ - "ramdisk_addr=fc180000\0" \ - "" - -#define CONFIG_HAS_ETH0 1 /* add support for "ethaddr" */ -#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ -#define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */ -#define CONFIG_PHY1_ADDR 3 - -/* Partitions */ - -#ifdef CONFIG_440EP -/* USB */ -#define CONFIG_USB_OHCI_NEW -#define CONFIG_SYS_OHCI_BE_CONTROLLER - -#undef CONFIG_SYS_USB_OHCI_BOARD_INIT -#define CONFIG_SYS_USB_OHCI_CPU_INIT 1 -#define CONFIG_SYS_USB_OHCI_REGS_BASE (CONFIG_SYS_PERIPHERAL_BASE | 0x1000) -#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ppc440" -#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 - -/* Comment this out to enable USB 1.1 device */ -#define USB_2_0_DEVICE - -#define CONFIG_SUPPORT_VFAT -#endif /* CONFIG_440EP */ - -#ifdef DEBUG -#define CONFIG_PANIC_HANG -#else -#define CONFIG_HW_WATCHDOG /* watchdog */ -#endif - -/* - * Commands additional to the ones defined in amcc-common.h - */ -#define CONFIG_CMD_PCI - -#ifdef CONFIG_440EP -#endif - -/*----------------------------------------------------------------------- - * PCI stuff - *----------------------------------------------------------------------- - */ -/* General PCI */ -#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ -#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE*/ - -/* Board-specific PCI */ -#define CONFIG_SYS_PCI_TARGET_INIT -#define CONFIG_SYS_PCI_MASTER_INIT - -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ -#define CONFIG_SYS_PCI_SUBSYS_ID 0xcafe /* Whatever */ - -/*----------------------------------------------------------------------- - * External Bus Controller (EBC) Setup - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_FLASH CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_CPLD 0x80000000 - -/* Memory Bank 0 (NOR-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB0AP 0x03017300 -#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH | 0xda000) - -/* Memory Bank 2 (CPLD) initialization */ -#define CONFIG_SYS_EBC_PB2AP 0x04814500 -#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_CPLD | 0x18000) - -#define CONFIG_SYS_BCSR5_PCI66EN 0x80 - -#endif /* __CONFIG_H */ |