summaryrefslogtreecommitdiff
path: root/include/configs/omap3logic.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs/omap3logic.h')
-rw-r--r--include/configs/omap3logic.h429
1 files changed, 300 insertions, 129 deletions
diff --git a/include/configs/omap3logic.h b/include/configs/omap3logic.h
index f797cbcce7..5dfeb9bb72 100644
--- a/include/configs/omap3logic.h
+++ b/include/configs/omap3logic.h
@@ -41,6 +41,10 @@
#define CONFIG_OMAP34XX 1 /* which is a 34XX */
#define CONFIG_OMAP3430 1 /* which is in a 3430 */
#define CONFIG_OMAP3_LOGIC 1 /* working with Logic OMAP boards */
+#define CONFIG_OMAP_DMA 1
+
+#define CONFIG_USE_ARCH_MEMSET 1
+#define CONFIG_USE_ARCH_MEMCPY 1
/* Define following to enable new product ID code. */
#define CONFIG_OMAP3_LOGIC_USE_NEW_PRODUCT_ID 1
@@ -97,6 +101,7 @@
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE (-4)
#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
+#define CONFIG_SERIAL_OUTPUT_FIFO /* Use full serial tx fifo */
/*
* select serial console configuration
@@ -120,12 +125,14 @@
/* DDR - I use Micron DDR */
#define CONFIG_OMAP3_MICRON_DDR 1
+#if 0
/* USB
* Enable CONFIG_MUSB_HCD for Host functionalities MSC, keyboard
* Enable CONFIG_MUSB_UDD for Device functionalities.
*/
#define CONFIG_USB_OMAP3 1
#define CONFIG_MUSB_HCD 1
+#endif
/* #define CONFIG_MUSB_UDC 1 */
#ifdef CONFIG_USB_OMAP3
@@ -173,10 +180,18 @@
#define CONFIG_CMD_NAND /* NAND support */
#define CONFIG_MTD_DEVICE /* needed for MTD mtdparts support */
#define CONFIG_CMD_MTDPARTS /* MTD partition support */
-#define MTDIDS_DEFAULT "nand0=omap2-nand.0"
-#define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:512k(x-loader),"\
+#define MTDIDS_NAND_DEFAULT "nand0=omap2-nand.0"
+#define MTDIDS_NOR_DEFAULT "nor0=physmap-flash.0"
+#define MTDPARTS_NAND_DEFAULT "mtdparts=omap2-nand.0:512k(x-loader),"\
"1664k(u-boot),384k(u-boot-env),"\
"5m(kernel),20m(ramdisk),-(fs)"
+
+#define MTDPARTS_NOR_DEFAULT "physmap-flash.0:-(nor)"
+
+/* mtdparts/id default values are dynamic since some modules may
+ * not have NOR flash */
+#define CONFIG_MTDPARTS_DYNAMIC_DEFAULT
+
#define CONFIG_NAND_SET_DEFAULT /* Set default NAND access method */
#define CONFIG_NAND_MULTIPLE_ECC /* NAND has multiple ECC methods */
#define CONFIG_TOUCHUP_ENV /* Set board-specific environment vars */
@@ -186,7 +201,11 @@
#define CONFIG_CMD_CACHE /* Cache control */
#define CONFIG_CMD_TIME /* time command */
+#if 0
+/* L2 was disabled since observed that large displays (720p) weren't working
+ * Verify can boot kernel using either XGA or 720p HDMI displays settings */
#define CONFIG_L2_OFF 1 /* Keep L2 Cache Disabled */
+#endif
#define BOARD_LATE_INIT
@@ -198,9 +217,10 @@
#define CONFIG_CMD_GPMC_CONFIG /* gpmc_config */
#define CONFIG_CMD_MUX_CONFIG /* mux_config */
#define CONFIG_CMD_SDRC_CONFIG /* sdrc_config */
+#define CONFIG_CMD_SETEXPR /* setexpr command */
#define CONFIG_HARD_I2C 1
-#define CONFIG_SYS_I2C_SPEED 100000
+#define CONFIG_SYS_I2C_SPEED 400000
#define CONFIG_SYS_I2C_SLAVE 1
#define CONFIG_SYS_I2C_BUS 0
#define CONFIG_SYS_I2C_BUS_SELECT 1
@@ -294,10 +314,11 @@
/* variables as indicated below for a successful boot. */
/* */
/* - $kernel_location */
-/* Must always be set. Values can be ram, nand, mmc, or tftp. */
+/* Must always be set. Values can be ram, nand, nand-part, mmc, or tftp. */
/* */
/* - $rootfs_location */
-/* Must always be set. Values can be ram, tftp, /dev, nfs, mmc, or nand. */
+/* Must always be set. Values can be: */
+/* ram, tftp, /dev, nfs, mmc, nand, nand-part. */
/* */
/* - $rootfs_type */
/* Must always be set. Values can be ramdisk, jffs, yaffs, ext3, or nfs. */
@@ -307,25 +328,54 @@
/* */
/* - If booting from /dev based file system, then $rootfs_device must be */
/* set. */
+/* - If booting kernel from nand-part location, $kernel_partition */
+/* must be set. */
+/* - If rootfs is coming from nand-part (i.e. ramdisk in NAND), then */
+/* $ramdisk_partition must be set. */
+/* must be set. */
/* - If booting from a ramdisk image, then $ramdisksize, and $ramdiskaddr */
/* must be set. */
/* - If booting from an nfs location, then $serverip, $nfsrootpath, and */
/* $nfsoptions must be set. */
-/* - If booting from nand, $ramdisk_nand_offset, $ramdisk_nand_size, */
-/* $kernel_nand_offset, and $kernel_nand_size must be set. */
+/* - If booting from nand, $ramdisk_partition, */
+/* $kernel_partition must be set. */
/* - If booting from a file system, $ramdiskimage, and $kernelimage must be */
/* set. */
/* - Optionally, a boot script named "boot.scr" can be placed in SD to */
/* override any other boot scripts. */
/*****************************************************************************/
+
+/*****************************************************************************/
+/* When using the makenandboot script, be sure to set: */
+/* */
+/* - xloadimage File name of x-loader on the SD card */
+/* - ubootimage File name of u-boot on the SD card */
+/* - kernelimage File name of the kernel image on the SD card */
+/* - ramdiskimage File name of the ramdisk image on the SD card */
+/* - xloader_partition Name of the x-loader partition in mtdparts */
+/* - uboot_partition Name of the u-boot partition in mtdparts */
+/* - kernel_partition Name of the kernel partition in mtdparts */
+/* - ramdisk_partition Name of the ramdisk partition in mtdparts */
+/* */
+/* When using makeyaffsboot script, be sure to set: */
+/* */
+/* - xloadimage File name of x-loader on the SD card */
+/* - ubootimage File name of u-boot on the SD card */
+/* - kernelimage File name of the kernel image on the SD card */
+/* - yaffsimage File name of the YAFFS root FS on the SD card */
+/* - xloader_partition Name of the x-loader partition in mtdparts */
+/* - uboot_partition Name of the u-boot partition in mtdparts */
+/* - kernel_partition Name of the kernel partition in mtdparts */
+/* - yaffs_partition Name of the YAFFS root FS in mtdparts */
+/*****************************************************************************/
+
#define CONFIG_EXTRA_ENV_SETTINGS \
OMAP3LOGIC_USBTTY \
"bootargs=\0" \
"otherbootargs=ignore_loglevel early_printk no_console_suspend \0" \
"consoledevice=ttyO0\0" \
+ "autoload=no\0" \
"setconsole=setenv console ${consoledevice},${baudrate}n8\0" \
- "mtdids=" MTDIDS_DEFAULT "\0" \
- "mtdparts=" MTDPARTS_DEFAULT "\0" \
"disablecharging=no\0" \
"mmc_bootscript_addr=0x80FF0000\0" \
"disablecharging no\0" \
@@ -334,132 +384,163 @@
"kernel_location=mmc \0" \
"rootfs_location=mmc \0" \
"rootfs_type=ramdisk \0" \
- "rootfs_device=/dev/mtdblock4 \0" \
+ "rootfs_device=/dev/mtdblock5 \0" \
+ "xloadimage=mlo\0" \
+ "ubootimage=u-boot.bin.ift\0" \
+ "kernelimage=uImage\0" \
+ "ramdiskimage=rootfs.ext2.gz.uboot\0" \
+ "yaffsimage=rootfs.yaffs2\0" \
+ "xloader_partition=x-loader\0" \
+ "uboot_partition=u-boot\0" \
+ "kernel_partition=kernel\0" \
+ "ramdisk_partition=ramdisk\0" \
+ "yaffs_partition=fs\0" \
+ "arg_loadcmd=fatload mmc 1\0" \
"ramdisksize=64000\0" \
"ramdiskaddr=0x82000000\0" \
- "ramdiskimage=rootfs.ext2.gz.uboot\0" \
- "ramdisk_nand_offset=0x00680000\0" \
- "ramdisk_nand_size=0x00d40000\0" \
- "kernel_nand_offset=0x00280000 \0" \
- "kernel_nand_size=0x00400000 \0" \
- "kernelimage=uImage \0" \
- "serverip=192.168.3.5\0" \
+ "tftpdir=\0" \
+ "serverip=192.168.3.10\0" \
"nfsrootpath=/opt/nfs-exports/ltib-omap\0" \
"nfsoptions=,wsize=1500,rsize=1500\0" \
"rotation=0\0" \
- "autoboot=echo \"\n== Checking mmc1 for alternate boot script " CONFIG_MMC_BOOTSCRIPT_NAME " ==\"; " \
- "if mmc init; then " \
- "if run loadbootscript; then " \
- "echo \"\"; " \
- "echo \"== Found script on mmc 1, starting ==\"; " \
- "run bootscript; " \
- "else " \
- "echo \"\"; " \
- "echo \"== Script not found on mmc 1, proceeding with defaultboot ==\"; " \
- "run defaultboot;" \
- "fi; " \
- "else run defaultboot; fi\0" \
+ "autoboot=echo \"\n== Checking mmc1 for alternate boot script " CONFIG_MMC_BOOTSCRIPT_NAME " ==\";" \
+ " if mmc init; then \n" \
+ " if run loadbootscript; then \n" \
+ " echo \"\"; \n" \
+ " echo \"== Found script on mmc 1, starting ==\"; \n" \
+ " run bootscript; \n" \
+ " else \n" \
+ " echo \"\"; \n" \
+ " echo \"== Script not found on mmc 1, proceeding with defaultboot ==\"; \n" \
+ " run defaultboot;\n" \
+ " fi; \n" \
+ " else run defaultboot; fi\0" \
"loadbootscript=fatload mmc 1 $mmc_bootscript_addr " CONFIG_MMC_BOOTSCRIPT_NAME "\0" \
"bootscript=source ${mmc_bootscript_addr}\0" \
- "vrfb_arg=if itest ${rotation} -ne 0; then " \
- "setenv bootargs ${bootargs} omapfb.vrfb=y omapfb.rotate=${rotation}; " \
+ "vrfb_arg=if itest ${rotation} -ne 0; then \n" \
+ "setenv bootargs ${bootargs} omapfb.vrfb=y omapfb.rotate=${rotation}; \n" \
"fi\0" \
"dump_bootargs=echo \"\"; echo \"== Kernel bootargs ==\"; echo $bootargs; echo \"\"; \0" \
"dump_boot_sources=echo \"kernel_location: $kernel_location, " \
"rootfs_location: $rootfs_location, " \
- "rootfs_type: $rootfs_type\"; " \
+ "rootfs_type: $rootfs_type\"; " \
"echo \"\"; " \
- "\0" \
- "load_kernel=if test $kernel_location = 'ram'; then " \
- "echo \"== kernel located at $loadaddr ==\"; " \
- "echo \"\"; " \
- "setenv bootm_arg1 ${loadaddr};" \
- "else if test $kernel_location = 'nand'; then " \
- "echo \"== Loading kernel from nand to $loadaddr ==\"; " \
- "nand read.i $loadaddr $kernel_nand_offset $kernel_nand_size; " \
- "echo \"\"; " \
- "setenv bootm_arg1 ${loadaddr};" \
- "else if test $kernel_location = 'mmc'; then " \
- "echo \"== Loading kernel file $kernelimage to $loadaddr ==\"; " \
- "mmc init; " \
- "fatload mmc 1 $loadaddr $kernelimage; " \
- "echo \"\"; " \
- "setenv bootm_arg1 ${loadaddr};" \
- "else if test $kernel_location = 'tftp'; then " \
- "echo \"== Loading kernel file $tftpdir$kernelimage to $loadaddr ==\"; " \
- "tftpboot $loadaddr $tftpdir$kernelimage; " \
- "echo \"\"; " \
- "setenv bootm_arg1 ${loadaddr};" \
- "else "\
- "echo \"== kernel_location must be set to ram, nand, mmc, or tftp!! ==\"; " \
- "echo \"\"; " \
- "fi; " \
- "fi; " \
- "fi; " \
- "fi " \
- "\0" \
- "load_rootfs=if test $rootfs_location = 'ram'; then " \
- "echo \"== rootfs located at $ramdiskaddr ==\"; " \
- "echo \"\"; " \
- "setenv bootm_arg2 ${ramdiskaddr}; " \
- "else if test $rootfs_location = 'tftp'; then " \
- "echo \"== Loading rootfs file $tftpdir$ramdiskimage to $ramdiskaddr ==\"; " \
- "tftpboot $ramdiskaddr $tftpdir$ramdiskimage;" \
- "echo \"\"; " \
- "setenv bootm_arg2 ${ramdiskaddr}; " \
- "else if test $rootfs_location = '/dev'; then " \
- "echo \"== rootfs located in $rootfs_device ==\"; " \
- "echo \"\"; " \
- "setenv bootargs ${bootargs} root=${rootfs_device}; " \
- "setenv bootm_arg2; " \
- "else if test $rootfs_location = 'nfs'; then " \
- "echo \"== rootfs located at $nfs_root_path on server $serverip ==\"; " \
- "echo \"\"; " \
- "setenv bootargs ${bootargs} root=/dev/nfs; " \
- "setenv bootm_arg2; " \
- "else if test $rootfs_location = 'mmc'; then " \
- "echo \"== Loading rootfs file $ramdiskimage to $ramdiskaddr ==\"; " \
- "fatload mmc 1 ${ramdiskaddr} ${ramdiskimage}; "\
- "setenv bootm_arg2 ${ramdiskaddr}; " \
- "else if test $rootfs_location = 'nand'; then " \
- "echo \"== Loading rootfs from nand to $ramdiskaddr ==\"; " \
- "nand read.i $ramdiskaddr $ramdisk_nand_offset $ramdisk_nand_size; " \
- "setenv bootm_arg2 ${ramdiskaddr}; " \
- "else "\
- "echo \"== rootfs_location must be set to ram, tftp, /dev, nfs, mmc, or nand!! == \"; " \
- "echo \"\"; " \
- "fi; " \
- "fi; " \
- "fi; " \
- "fi; " \
- "fi; " \
- "fi " \
- "\0" \
- "set_rootfs_type=if test $rootfs_type = 'ramdisk'; then " \
- "setenv bootargs ${bootargs} root=/dev/ram rw ramdisk_size=${ramdisksize}; " \
- "else if test $rootfs_type = 'jffs'; then " \
- "setenv bootargs ${bootargs} rw rootfstype=jffs2;" \
- "else if test $rootfs_type = 'yaffs'; then " \
- "setenv bootargs ${bootargs} rw rootfstype=yaffs2;" \
- "else if test $rootfs_type = 'ext3'; then " \
- "setenv bootargs ${bootargs} rw rootfstype=ext3 rootwait; " \
- "else if test $rootfs_type = 'nfs'; then " \
- "setenv bootargs ${bootargs} rw nfsroot=${serverip}:${nfsrootpath}${nfsoptions} ip=dhcp; " \
- "else "\
- "echo \"$rootfs_type must be set to ramdisk, jffs, yaffs, ext3, or nfs\"; " \
- "echo \"\"; " \
- "fi; " \
- "fi; " \
- "fi; " \
- "fi; " \
- "fi " \
- "\0" \
+ "\0" \
+ "load_kernel=if test $kernel_location = 'ram'; then \n" \
+ " echo \"== kernel located at $loadaddr ==\"; \n" \
+ " echo \"\"; \n" \
+ " setenv bootm_arg1 ${loadaddr};\n" \
+ " else \n" \
+ " if test $kernel_location = 'nand'; then \n" \
+ " echo \"== Loading kernel from nand to $loadaddr ==\"; \n" \
+ " nand read.i $loadaddr $kernel_partition; \n" \
+ " echo \"\"; \n" \
+ " setenv bootm_arg1 ${loadaddr};\n" \
+ " else \n" \
+ " if test $kernel_location = 'nand-part'; then \n" \
+ " echo \"== Loading kernel from nand partition $kernel_partition to $loadaddr ==\"; \n" \
+ " nboot $loadaddr $kernel_partition; \n" \
+ " echo \"\"; \n" \
+ " setenv bootm_arg1 ${loadaddr};\n" \
+ " else \n" \
+ " if test $kernel_location = 'mmc'; then \n" \
+ " echo \"== Loading kernel file $kernelimage to $loadaddr ==\"; \n" \
+ " mmc init; \n" \
+ " fatload mmc 1 $loadaddr $kernelimage; \n" \
+ " echo \"\"; \n" \
+ " setenv bootm_arg1 ${loadaddr};\n" \
+ " else \n" \
+ " if test $kernel_location = 'tftp'; then \n" \
+ " echo \"== Loading kernel file $tftpdir$kernelimage to $loadaddr ==\"; \n" \
+ " tftpboot $loadaddr $tftpdir$kernelimage; \n" \
+ " echo \"\"; \n" \
+ " setenv bootm_arg1 ${loadaddr};\n" \
+ " else \n" \
+ " echo \"== kernel_location must be set to ram, nand, mmc, or tftp!! ==\"; \n" \
+ " echo \"\"; \n" \
+ " fi; \n" \
+ " fi; \n" \
+ " fi; \n" \
+ " fi; \n" \
+ " fi\n " \
+ "\0" \
+ "load_rootfs=if test $rootfs_location = 'ram'; then \n" \
+ " echo \"== rootfs located at $ramdiskaddr ==\"; \n" \
+ " echo \"\"; \n" \
+ " setenv bootm_arg2 ${ramdiskaddr}; \n" \
+ " else \n" \
+ " if test $rootfs_location = 'tftp'; then \n" \
+ " echo \"== Loading rootfs file $tftpdir$ramdiskimage to $ramdiskaddr ==\"; \n" \
+ " tftpboot $ramdiskaddr $tftpdir$ramdiskimage;\n" \
+ " echo \"\"; \n" \
+ " setenv bootm_arg2 ${ramdiskaddr}; \n" \
+ " else \n" \
+ " if test $rootfs_location = '/dev'; then \n" \
+ " echo \"== rootfs located in $rootfs_device ==\"; \n" \
+ " echo \"\"; \n" \
+ " setenv bootargs ${bootargs} root=${rootfs_device}; \n" \
+ " setenv bootm_arg2; \n" \
+ " else \n" \
+ " if test $rootfs_location = 'nfs'; then \n" \
+ " echo \"== rootfs located at $nfsrootpath on server $serverip ==\"; \n" \
+ " echo \"\"; \n" \
+ " setenv bootargs ${bootargs} root=/dev/nfs; \n" \
+ " setenv bootm_arg2; \n" \
+ " else \n" \
+ " if test $rootfs_location = 'mmc'; then\n " \
+ " echo \"== Loading rootfs file $ramdiskimage to $ramdiskaddr ==\"; \n" \
+ " fatload mmc 1 ${ramdiskaddr} ${ramdiskimage}; \n"\
+ " setenv bootm_arg2 ${ramdiskaddr}; \n" \
+ " else \n" \
+ " if test $rootfs_location = 'nand'; then \n" \
+ " echo \"== Loading rootfs from nand to $ramdiskaddr ==\"; \n" \
+ " nand read.i $ramdiskaddr $ramdisk_partition; \n" \
+ " setenv bootm_arg2 ${ramdiskaddr}; \n" \
+ " else \n"\
+ " if test $rootfs_location = 'nand-part'; then \n" \
+ " echo \"== Loading rootfs from nand partition $ramdisk_partition to $ramdiskaddr ==\"; \n" \
+ " nand read.i $ramdiskaddr $ramdisk_partition; \n" \
+ " setenv bootm_arg2 ${ramdiskaddr}; \n" \
+ " else \n"\
+ " echo \"== rootfs_location must be set to ram, tftp, /dev, nfs, mmc, nand-part or nand!! == \"; \n" \
+ " echo \"\"; \n" \
+ " fi; \n" \
+ " fi; \n" \
+ " fi; \n" \
+ " fi; \n" \
+ " fi; \n" \
+ " fi; \n" \
+ " fi" \
+ "\0" \
+ "set_rootfs_type=if test $rootfs_type = 'ramdisk'; then \n" \
+ " setenv bootargs ${bootargs} root=/dev/ram rw ramdisk_size=${ramdisksize}; \n" \
+ " else \n" \
+ " if test $rootfs_type = 'jffs'; then \n" \
+ " setenv bootargs ${bootargs} rw rootfstype=jffs2;\n" \
+ " else \n" \
+ " if test $rootfs_type = 'yaffs'; then \n" \
+ " setenv bootargs ${bootargs} rw rootfstype=yaffs2;\n" \
+ " else \n" \
+ " if test $rootfs_type = 'ext3'; then \n" \
+ " setenv bootargs ${bootargs} rw rootfstype=ext3 rootwait; \n" \
+ " else \n" \
+ " if test $rootfs_type = 'nfs'; then \n" \
+ " setenv bootargs ${bootargs} rw nfsroot=${serverip}:${nfsrootpath}${nfsoptions} ip=dhcp; \n" \
+ " else \n"\
+ " echo \"$rootfs_type must be set to ramdisk, jffs, yaffs, ext3, or nfs\"; \n" \
+ " echo \"\"; \n" \
+ " fi; \n" \
+ " fi; \n" \
+ " fi; \n" \
+ " fi; \n" \
+ " fi" \
+ "\0" \
"addmtdparts=setenv bootargs ${bootargs} ${mtdparts} \0" \
"common_bootargs=" \
" setenv bootargs ${bootargs} display=${display} ${otherbootargs}; " \
" run addmtdparts; " \
" run vrfb_arg; " \
- " \0" \
+ "\0" \
"dump_run_bootm=" \
" echo \"bootm $bootm_arg1 $bootm_arg2\"; " \
" echo \"\"; " \
@@ -470,30 +551,118 @@
" run common_bootargs; " \
" run load_kernel; " \
" run load_rootfs; " \
- " run set_rootfs_type; " \
+ " run set_rootfs_type; " \
" run dump_bootargs; " \
" run dump_run_bootm; " \
+ "\0" \
"nfsboot=" \
" setenv kernel_location tftp; " \
" setenv rootfs_location nfs; " \
" setenv rootfs_type nfs; " \
" run defaultboot; " \
"\0" \
- "mtdboot=" \
- " setenv kernel_location mmc; " \
- " setenv rootfs_location mmc; " \
- " setenv rootfs_type ramdisk; " \
- " run defaultboot; " \
- "\0" \
"ramboot=" \
" setenv kernel_location tftp; " \
" setenv rootfs_location tftp; " \
" setenv rootfs_type ramdisk; " \
" run defaultboot; " \
+ "\0" \
+ "checkerror=if test $error = '';\n" \
+ " then\n" \
+ " echo \033[31m${error}\033[0m\n" \
+ " echo_lcd /pAA/k${error}\n" \
+ " else\n" \
+ " echo \033[1mDone!\033[m\n" \
+ " echo_lcd /pAA/kCompleted burning sucessfully./n\n" \
+ " echo_lcd /kIt is safe to remove the SD card/n\n" \
+ " echo_lcd /kand restart the devkit./n\n" \
+ " fi" \
+ "\0" \
+ "initmmc=if test $error = '';then;else\n" \
+ " if mmc init;then;else;\n" \
+ " setenv error \"Failed to initialize MMC\"\n" \
+ " fi\n" \
+ " fi" \
+ "\0" \
+ "checkmmcfile=if test $error = '';then;else\n" \
+ " if fatload mmc 1 ${loadaddr} ${arg_filename} 1;then;else;\n" \
+ " setenv error \"Unable to load ${arg_filename}\";\n" \
+ " fi\n" \
+ " fi" \
+ "\0" \
+ "burnfile=if test $error = '';then;else\n" \
+ " echo \"\033[1m== Loading ${arg_filename} ==\033[0m\"\n" \
+ " echo_lcd /pAA/kPartition ${arg_partition}:\n" \
+ " echo_lcd /pBA/kLoading ${arg_filename}/aC;lcd_percent \"/gC/k /P%...\"\n" \
+ " if ${arg_loadcmd} ${loadaddr} ${arg_filename};then;\n" \
+ " echo \"\033[1m== Burning ${arg_partition} ==\033[0m\"\n" \
+ " lcd_percent \"/pBA/kErasing Partition /P%...\"\n" \
+ " nand erase.part ${arg_partition}\n" \
+ " echo_lcd /pBA/kWriting ${arg_filename} to Partition/aC;lcd_percent \"/gC/k /P%...\"\n" \
+ " nand ${arg_writecmd} ${loadaddr} ${arg_partition} ${filesize}\n" \
+ " lcd_percent \"\"\n" \
+ " echo_lcd /pAA/k/pAB/k\n" \
+ " else\n" \
+ " setenv error \"Unable to load ${arg_filename}\"\n" \
+ " fi\n" \
+ " fi" \
+ "\0" \
+ "burnmmcxloader=if test $error = '';then;else\n" \
+ " nandecc hw;\n" \
+ " arg_filename=${xloadimage};arg_partition=${xloader_partition};arg_writecmd=write.i;\n" \
+ " run burnfile\n" \
+ " if test $error = '';then;else\n" \
+ " nand write.i ${loadaddr} 0x00020000 ${filesize}\n" \
+ " nand write.i ${loadaddr} 0x00040000 ${filesize}\n" \
+ " nand write.i ${loadaddr} 0x00060000 ${filesize}\n" \
+ " fi\n" \
+ " fi" \
+ "\0" \
+ "burncommon=if test $error = '';then;else\n" \
+ " arg_filename=${xloadimage};run checkmmcfile;\n" \
+ " arg_filename=${ubootimage};run checkmmcfile;\n" \
+ " arg_filename=${kernelimage};run checkmmcfile;\n" \
+ " run burnmmcxloader;\n" \
+ " nandecc ${defaultecc};\n" \
+ " arg_writecmd=write.i;\n" \
+ " arg_filename=${ubootimage};arg_partition=${uboot_partition};run burnfile;\n" \
+ " arg_filename=${kernelimage};arg_partition=${kernel_partition};run burnfile;\n" \
+ " fi" \
+ "\0" \
+ "makenandboot=if true;then;\n" \
+ " setenv error;\n" \
+ " run initmmc;\n" \
+ " arg_filename=${ramdiskimage};run checkmmcfile;\n" \
+ " run burncommon;\n" \
+ " arg_filename=${ramdiskimage};arg_partition=${ramdisk_partition};arg_writecmd=write.i;\n" \
+ " run burnfile;\n" \
+ " if test $error = '';then;else\n" \
+ " setenv kernel_location nand-part\n" \
+ " setenv rootfs_location nand-part\n" \
+ " setenv rootfs_type ramdisk\n" \
+ " saveenv\n" \
+ " fi\n" \
+ " run checkerror;\n" \
+ " fi" \
+ "\0" \
+ "makeyaffsboot=if true;then;\n" \
+ " setenv error;\n" \
+ " run initmmc;\n" \
+ " arg_filename=${yaffsimage};run checkmmcfile;\n" \
+ " run burncommon;\n" \
+ " arg_filename=${yaffsimage};arg_partition=${yaffs_partition};arg_writecmd=write.yaffs;\n" \
+ " run burnfile;\n" \
+ " if test $error = '';then;else\n" \
+ " setenv kernel_location nand-part\n" \
+ " setenv rootfs_location /dev\n" \
+ " setenv rootfs_type yaffs\n" \
+ " setenv rootfs_device /dev/mtdblock5\n" \
+ " saveenv\n" \
+ " fi\n" \
+ " run checkerror;\n" \
+ " fi" \
"\0"
-
-
#define CONFIG_AUTO_COMPLETE 1
/*
* Miscellaneous configurable options
@@ -554,9 +723,9 @@
*/
/* variable that's non-zero if flash exists */
-#define CONFIG_SYS_FLASH_PRESENCE omap3logic_flash_exists
+#define CONFIG_SYS_FLASH_PRESENCE omap3logic_nor_exists
#ifndef __ASSEMBLY__
-extern int omap3logic_flash_exists;
+extern int omap3logic_nor_exists;
#endif
#define CONFIG_SYS_FLASH_BASE 0x10000000 /* FLASH base address */
#define CONFIG_SYS_FLASH_SIZE 8 /* 8MB */
@@ -566,6 +735,7 @@ extern int omap3logic_flash_exists;
#undef CONFIG_SYS_FLASH_CHECKSUM
#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
+#define CONFIG_FLASH_CFI_MTD /* use the CFI MTD interface */
/* **** PISMO SUPPORT *** */
@@ -581,6 +751,7 @@ extern int omap3logic_flash_exists;
#define SMNAND_ENV_OFFSET 0x220000 /* environment starts here */
#if defined(CONFIG_CMD_NAND)
+#define CONFIG_SYS_NAND_QUIET_TEST 1
#define CONFIG_NAND_OMAP_GPMC
#define CONFIG_MTD_NAND_BCH
#define CONFIG_MTD_NAND_ECC_BCH
generated by cgit v1.2.3 (git 2.0.4) at 2024-06-27 12:51:01 +0000