diff options
Diffstat (limited to 'include/configs/makalu.h')
| -rw-r--r-- | include/configs/makalu.h | 332 |
1 files changed, 0 insertions, 332 deletions
diff --git a/include/configs/makalu.h b/include/configs/makalu.h deleted file mode 100644 index a92bc43538..0000000000 --- a/include/configs/makalu.h +++ /dev/null @@ -1,332 +0,0 @@ -/* - * Copyright (c) 2008 Nuovation System Designs, LLC - * Grant Erickson <gerickson@nuovations.com> - * - * (C) Copyright 2007-2008 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/************************************************************************ - * makalu.h - configuration for AMCC Makalu (405EX) - ***********************************************************************/ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/*----------------------------------------------------------------------- - * High Level Configuration Options - *----------------------------------------------------------------------*/ -#define CONFIG_MAKALU 1 /* Board is Makalu */ -#define CONFIG_405EX 1 /* Specifc 405EX support*/ -#define CONFIG_SYS_CLK_FREQ 33330000 /* ext frequency to pll */ - -#define CONFIG_SYS_TEXT_BASE 0xFFFA0000 - -/* - * Include common defines/options for all AMCC eval boards - */ -#define CONFIG_HOSTNAME makalu -#define CONFIG_ADDMISC "addmisc=setenv bootargs ${bootargs} rtc-x1205.probe=0,0x6f\0" -#include "amcc-common.h" - -#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ - -/*----------------------------------------------------------------------- - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_FLASH_BASE 0xFC000000 -#define CONFIG_SYS_FPGA_BASE 0xF0000000 - -/*----------------------------------------------------------------------- - * Initial RAM & Stack Pointer Configuration Options - * - * There are traditionally three options for the primordial - * (i.e. initial) stack usage on the 405-series: - * - * 1) On-chip Memory (OCM) (i.e. SRAM) - * 2) Data cache - * 3) SDRAM - * - * For the 405EX(r), there is no OCM, so we are left with (2) or (3) - * the latter of which is less than desireable since it requires - * setting up the SDRAM and ECC in assembly code. - * - * To use (2), define 'CONFIG_SYS_INIT_DCACHE_CS' to be an unused chip - * select on the External Bus Controller (EBC) and then select a - * value for 'CONFIG_SYS_INIT_RAM_ADDR' outside of the range of valid, - * physical SDRAM. Otherwise, undefine 'CONFIG_SYS_INIT_DCACHE_CS' and - * select a value for 'CONFIG_SYS_INIT_RAM_ADDR' within the range of valid, - * physical SDRAM to use (3). - *-----------------------------------------------------------------------*/ - -#define CONFIG_SYS_INIT_DCACHE_CS 4 - -#if defined(CONFIG_SYS_INIT_DCACHE_CS) -#define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_SDRAM_BASE + ( 1 << 30)) /* 1 GiB */ -#else -#define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_SDRAM_BASE + (32 << 20)) /* 32 MiB */ -#endif /* defined(CONFIG_SYS_INIT_DCACHE_CS) */ - -#define CONFIG_SYS_INIT_RAM_SIZE (4 << 10) /* 4 KiB */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - -/* - * If the data cache is being used for the primordial stack and global - * data area, the POST word must be placed somewhere else. The General - * Purpose Timer (GPT) is unused by u-boot and the kernel and preserves - * its compare and mask register contents across reset, so it is used - * for the POST word. - */ - -#if defined(CONFIG_SYS_INIT_DCACHE_CS) -# define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET -# define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_COMP6) -#else -# define CONFIG_SYS_INIT_EXTRA_SIZE 16 -# define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - CONFIG_SYS_INIT_EXTRA_SIZE) -# define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_INIT_RAM_ADDR -#endif /* defined(CONFIG_SYS_INIT_DCACHE_CS) */ - -/*----------------------------------------------------------------------- - * Serial Port - *----------------------------------------------------------------------*/ -#define CONFIG_CONS_INDEX 1 /* Use UART0 */ -#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no ext. clk */ - -/*----------------------------------------------------------------------- - * Environment - *----------------------------------------------------------------------*/ -#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ - -/*----------------------------------------------------------------------- - * FLASH related - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ -#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ - -#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE} -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ -#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ - -#ifdef CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) -#endif /* CONFIG_ENV_IS_IN_FLASH */ - -/*----------------------------------------------------------------------- - * DDR SDRAM - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_MBYTES_SDRAM (256) /* 256MB */ - -#define CONFIG_SYS_SDRAM0_MB0CF_BASE (( 0 << 20) + CONFIG_SYS_SDRAM_BASE) -#define CONFIG_SYS_SDRAM0_MB1CF_BASE ((128 << 20) + CONFIG_SYS_SDRAM_BASE) - -/* DDR1/2 SDRAM Device Control Register Data Values */ -#define CONFIG_SYS_SDRAM0_MB0CF ((CONFIG_SYS_SDRAM0_MB0CF_BASE >> 3) | \ - SDRAM_RXBAS_SDSZ_128MB | \ - SDRAM_RXBAS_SDAM_MODE2 | \ - SDRAM_RXBAS_SDBE_ENABLE) -#define CONFIG_SYS_SDRAM0_MB1CF ((CONFIG_SYS_SDRAM0_MB1CF_BASE >> 3) | \ - SDRAM_RXBAS_SDSZ_128MB | \ - SDRAM_RXBAS_SDAM_MODE2 | \ - SDRAM_RXBAS_SDBE_ENABLE) -#define CONFIG_SYS_SDRAM0_MB2CF SDRAM_RXBAS_SDBE_DISABLE -#define CONFIG_SYS_SDRAM0_MB3CF SDRAM_RXBAS_SDBE_DISABLE -#define CONFIG_SYS_SDRAM0_MCOPT1 0x04322000 -#define CONFIG_SYS_SDRAM0_MCOPT2 0x00000000 -#define CONFIG_SYS_SDRAM0_MODT0 0x01800000 -#define CONFIG_SYS_SDRAM0_MODT1 0x00000000 -#define CONFIG_SYS_SDRAM0_CODT 0x0080f837 -#define CONFIG_SYS_SDRAM0_RTR 0x06180000 -#define CONFIG_SYS_SDRAM0_INITPLR0 0xa8380000 -#define CONFIG_SYS_SDRAM0_INITPLR1 0x81900400 -#define CONFIG_SYS_SDRAM0_INITPLR2 0x81020000 -#define CONFIG_SYS_SDRAM0_INITPLR3 0x81030000 -#define CONFIG_SYS_SDRAM0_INITPLR4 0x81010404 -#define CONFIG_SYS_SDRAM0_INITPLR5 0x81000542 -#define CONFIG_SYS_SDRAM0_INITPLR6 0x81900400 -#define CONFIG_SYS_SDRAM0_INITPLR7 0x8D080000 -#define CONFIG_SYS_SDRAM0_INITPLR8 0x8D080000 -#define CONFIG_SYS_SDRAM0_INITPLR9 0x8D080000 -#define CONFIG_SYS_SDRAM0_INITPLR10 0x8D080000 -#define CONFIG_SYS_SDRAM0_INITPLR11 0x81000442 -#define CONFIG_SYS_SDRAM0_INITPLR12 0x81010780 -#define CONFIG_SYS_SDRAM0_INITPLR13 0x81010400 -#define CONFIG_SYS_SDRAM0_INITPLR14 0x00000000 -#define CONFIG_SYS_SDRAM0_INITPLR15 0x00000000 -#define CONFIG_SYS_SDRAM0_RQDC 0x80000038 -#define CONFIG_SYS_SDRAM0_RFDC 0x00000209 -#define CONFIG_SYS_SDRAM0_RDCC 0x40000000 -#define CONFIG_SYS_SDRAM0_DLCR 0x030000a5 -#define CONFIG_SYS_SDRAM0_CLKTR 0x80000000 -#define CONFIG_SYS_SDRAM0_WRDTR 0x00000000 -#define CONFIG_SYS_SDRAM0_SDTR1 0x80201000 -#define CONFIG_SYS_SDRAM0_SDTR2 0x32204232 -#define CONFIG_SYS_SDRAM0_SDTR3 0x080b0d1a -#define CONFIG_SYS_SDRAM0_MMODE 0x00000442 -#define CONFIG_SYS_SDRAM0_MEMODE 0x00000404 - -/*----------------------------------------------------------------------- - * I2C - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 - -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* I2C boot EEPROM (24C02BN) */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ - -/* RTC configuration */ -#define CONFIG_RTC_X1205 1 -#define CONFIG_SYS_I2C_RTC_ADDR 0x6f - -/*----------------------------------------------------------------------- - * Ethernet - *----------------------------------------------------------------------*/ -#define CONFIG_M88E1111_PHY 1 -#define CONFIG_IBM_EMAC4_V4 1 -#define CONFIG_EMAC_PHY_MODE EMAC_PHY_MODE_RGMII_RGMII -#define CONFIG_PHY_ADDR 6 /* PHY address, See schematics */ - -#define CONFIG_PHY_RESET 1 /* reset phy upon startup */ -#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ - -#define CONFIG_HAS_ETH0 1 - -#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ -#define CONFIG_PHY1_ADDR 0 - -/* - * Default environment variables - */ -#define CONFIG_EXTRA_ENV_SETTINGS \ - CONFIG_AMCC_DEF_ENV \ - CONFIG_AMCC_DEF_ENV_POWERPC \ - CONFIG_AMCC_DEF_ENV_PPC_OLD \ - CONFIG_AMCC_DEF_ENV_NOR_UPD \ - "kernel_addr=fc000000\0" \ - "fdt_addr=fc1e0000\0" \ - "ramdisk_addr=fc200000\0" \ - "pciconfighost=1\0" \ - "pcie_mode=RP:RP\0" \ - "" - -/* - * Commands additional to the ones defined in amcc-common.h - */ -#define CONFIG_CMD_PCI - -/* POST support */ -#define CONFIG_POST (CONFIG_SYS_POST_CACHE | \ - CONFIG_SYS_POST_CPU | \ - CONFIG_SYS_POST_ETHER | \ - CONFIG_SYS_POST_I2C | \ - CONFIG_SYS_POST_MEMORY | \ - CONFIG_SYS_POST_UART) - -/* Define here the base-addresses of the UARTs to test in POST */ -#define CONFIG_SYS_POST_UART_TABLE { CONFIG_SYS_NS16550_COM1, \ - CONFIG_SYS_NS16550_COM2 } - -#define CONFIG_LOGBUFFER -#define CONFIG_SYS_POST_CACHE_ADDR 0x00800000 /* free virtual address */ - -/*----------------------------------------------------------------------- - * PCI stuff - *----------------------------------------------------------------------*/ -#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ -#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ -#define CONFIG_PCI_CONFIG_HOST_BRIDGE - -/*----------------------------------------------------------------------- - * PCIe stuff - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_PCIE_MEMBASE 0x90000000 /* mapped PCIe memory */ -#define CONFIG_SYS_PCIE_MEMSIZE 0x08000000 /* 128 Meg, smallest incr per port */ - -#define CONFIG_SYS_PCIE0_CFGBASE 0xa0000000 /* remote access */ -#define CONFIG_SYS_PCIE0_XCFGBASE 0xb0000000 /* local access */ -#define CONFIG_SYS_PCIE0_CFGMASK 0xe0000001 /* 512 Meg */ - -#define CONFIG_SYS_PCIE1_CFGBASE 0xc0000000 /* remote access */ -#define CONFIG_SYS_PCIE1_XCFGBASE 0xd0000000 /* local access */ -#define CONFIG_SYS_PCIE1_CFGMASK 0xe0000001 /* 512 Meg */ - -#define CONFIG_SYS_PCIE0_UTLBASE 0xef502000 -#define CONFIG_SYS_PCIE1_UTLBASE 0xef503000 - -/* base address of inbound PCIe window */ -#define CONFIG_SYS_PCIE_INBOUND_BASE 0x0000000000000000ULL - -/*----------------------------------------------------------------------- - * External Bus Controller (EBC) Setup - *----------------------------------------------------------------------*/ -/* Memory Bank 0 (NOR-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB0AP 0x08033700 -#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH_BASE | 0xda000) - -/* Memory Bank 2 (CPLD) initialization */ -#define CONFIG_SYS_EBC_PB2AP 0x9400C800 -#define CONFIG_SYS_EBC_PB2CR 0xF0018000 /* BAS=0x800,BS=1MB,BU=R/W,BW=8bit */ - -#define CONFIG_SYS_EBC_CFG 0x7FC00000 /* EBC0_CFG */ - -/*----------------------------------------------------------------------- - * GPIO Setup - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \ -{ \ -/* GPIO Core 0 */ \ -{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO0 EBC_DATA_PAR(0) */ \ -{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO1 EBC_DATA_PAR(1) */ \ -{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO2 EBC_DATA_PAR(2) */ \ -{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO3 EBC_DATA_PAR(3) */ \ -{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO4 EBC_DATA(20) USB2_DATA(4) */ \ -{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO5 EBC_DATA(21) USB2_DATA(5) */ \ -{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO6 EBC_DATA(22) USB2_DATA(6) */ \ -{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO7 EBC_DATA(23) USB2_DATA(7) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 CS(1)/NFCE(1) IRQ(7) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 CS(2)/NFCE(2) IRQ(8) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 CS(3)/NFCE(3) IRQ(9) */ \ -{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO11 IRQ(6) */ \ -{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO12 EBC_DATA(16) USB2_DATA(0) */ \ -{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO13 EBC_DATA(17) USB2_DATA(1) */ \ -{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO14 EBC_DATA(18) USB2_DATA(2) */ \ -{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO15 EBC_DATA(19) USB2_DATA(3) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO16 UART0_DCD UART1_CTS */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 UART0_DSR UART1_RTS */ \ -{GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 UART0_CTS */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO19 UART0_RTS */ \ -{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO20 UART0_DTR UART1_TX */ \ -{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO21 UART0_RI UART1_RX */ \ -{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO22 EBC_HOLD_REQ DMA_ACK2 */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_0}, /* GPIO23 EBC_HOLD_ACK DMA_REQ2 */ \ -{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO24 EBC_EXT_REQ DMA_EOT2 IRQ(4) */ \ -{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO25 EBC_EXT_ACK DMA_ACK3 IRQ(3) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO26 EBC_ADDR(5) DMA_EOT0 TS(3) */ \ -{GPIO0_BASE, GPIO_IN, GPIO_SEL , GPIO_OUT_0}, /* GPIO27 EBC_BUS_REQ DMA_EOT3 IRQ(5) */ \ -{GPIO0_BASE, GPIO_IN, GPIO_SEL , GPIO_OUT_0}, /* GPIO28 */ \ -{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO29 DMA_EOT1 IRQ(2) */ \ -{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO30 DMA_REQ1 IRQ(1) */ \ -{GPIO0_BASE, GPIO_IN, GPIO_ALT2, GPIO_OUT_0}, /* GPIO31 DMA_ACK1 IRQ(0) */ \ -} \ -} - -#define CONFIG_SYS_GPIO_PCIE_RST 23 -#define CONFIG_SYS_GPIO_PCIE_CLKREQ 27 -#define CONFIG_SYS_GPIO_PCIE_WAKE 28 - -#endif /* __CONFIG_H */ |