diff options
Diffstat (limited to 'include/configs/bubinga.h')
| -rw-r--r-- | include/configs/bubinga.h | 299 |
1 files changed, 0 insertions, 299 deletions
diff --git a/include/configs/bubinga.h b/include/configs/bubinga.h deleted file mode 100644 index 7274b2d4fe..0000000000 --- a/include/configs/bubinga.h +++ /dev/null @@ -1,299 +0,0 @@ -/* - * (C) Copyright 2000-2005 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_405EP 1 /* This is a PPC405 CPU */ -#define CONFIG_BUBINGA 1 /* ...on a BUBINGA board */ - -#define CONFIG_SYS_TEXT_BASE 0xFFFC0000 - -/* - * Include common defines/options for all AMCC eval boards - */ -#define CONFIG_HOSTNAME bubinga -#include "amcc-common.h" - -#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ - -#define CONFIG_NO_SERIAL_EEPROM -/*#undef CONFIG_NO_SERIAL_EEPROM*/ -/*----------------------------------------------------------------------------*/ -#ifdef CONFIG_NO_SERIAL_EEPROM - -/* -!------------------------------------------------------------------------------- -! Defines for entry options. -! Note: Because the 405EP SDRAM controller does not support ECC, ECC DIMMs that -! are plugged in the board will be utilized as non-ECC DIMMs. -!------------------------------------------------------------------------------- -*/ -#define AUTO_MEMORY_CONFIG -#define DIMM_READ_ADDR 0xAB -#define DIMM_WRITE_ADDR 0xAA - -/* -!------------------------------------------------------------------------------- -! PLL settings for 266MHz CPU, 133MHz PLB/SDRAM, 66MHz EBC, 33MHz PCI, -! assuming a 33MHz input clock to the 405EP from the C9531. -!------------------------------------------------------------------------------- -*/ -#define PLLMR0_DEFAULT PLLMR0_266_133_66 -#define PLLMR1_DEFAULT PLLMR1_266_133_66 - -#endif -/*----------------------------------------------------------------------------*/ - -/* - * Define here the location of the environment variables (FLASH or NVRAM). - * Note: DENX encourages to use redundant environment in FLASH. NVRAM is only - * supported for backward compatibility. - */ -#if 1 -#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ -#else -#define CONFIG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */ -#endif - -/* - * Default environment variables - */ -#define CONFIG_EXTRA_ENV_SETTINGS \ - CONFIG_AMCC_DEF_ENV \ - CONFIG_AMCC_DEF_ENV_PPC \ - CONFIG_AMCC_DEF_ENV_NOR_UPD \ - "kernel_addr=fff80000\0" \ - "ramdisk_addr=fff90000\0" \ - "" - -#define CONFIG_PHY_ADDR 1 /* PHY address */ -#define CONFIG_HAS_ETH0 -#define CONFIG_HAS_ETH1 -#define CONFIG_PHY1_ADDR 2 /* EMAC1 PHY address */ - -#define CONFIG_RTC_DS174x 1 /* use DS1743 RTC in Bubinga */ - -/* - * Commands additional to the ones defined in amcc-common.h - */ -#define CONFIG_CMD_PCI -#define CONFIG_CMD_SDRAM - -#define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */ - -/* - * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1. - * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31. - * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value. - * The Linux BASE_BAUD define should match this configuration. - * baseBaud = cpuClock/(uartDivisor*16) - * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock, - * set Linux BASE_BAUD to 403200. - */ -#define CONFIG_CONS_INDEX 1 /* Use UART0 */ -#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ -#undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ -#define CONFIG_SYS_BASE_BAUD 691200 - -/*----------------------------------------------------------------------- - * I2C stuff - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 - -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* avoid i2c probe hangup (?) */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */ - -#if defined(CONFIG_CMD_EEPROM) -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* I2C boot EEPROM (24C02W) */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ -#endif - -/*----------------------------------------------------------------------- - * PCI stuff - *----------------------------------------------------------------------- - */ -#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */ -#define PCI_HOST_FORCE 1 /* configure as pci host */ -#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ - -#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ -#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ - /* resource configuration */ -#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ - -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ -#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ -#define CONFIG_SYS_PCI_CLASSCODE 0x0600 /* PCI Class Code: bridge/host */ -#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ -#define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */ -#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ -#define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */ -#define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */ -#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ - -/*----------------------------------------------------------------------- - * External peripheral base address - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_KEY_REG_BASE_ADDR 0xF0100000 -#define CONFIG_SYS_IR_REG_BASE_ADDR 0xF0200000 -#define CONFIG_SYS_FPGA_REG_BASE_ADDR 0xF0300000 - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - */ -#define CONFIG_SYS_SRAM_BASE 0xFFF00000 -#define CONFIG_SYS_SRAM_SIZE (256 << 10) -#define CONFIG_SYS_FLASH_BASE 0xFFF80000 - -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -#define CONFIG_SYS_FLASH_ADDR0 0x5555 -#define CONFIG_SYS_FLASH_ADDR1 0x2aaa -#define CONFIG_SYS_FLASH_WORD_SIZE unsigned char - -#ifdef CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) -#endif /* CONFIG_ENV_IS_IN_FLASH */ - -/*----------------------------------------------------------------------- - * NVRAM organization - */ -#define CONFIG_SYS_NVRAM_BASE_ADDR 0xf0000000 /* NVRAM base address */ -#define CONFIG_SYS_NVRAM_SIZE 0x1ff8 /* NVRAM size */ - -#ifdef CONFIG_ENV_IS_IN_NVRAM -#define CONFIG_ENV_SIZE 0x0ff8 /* Size of Environment vars */ -#define CONFIG_ENV_ADDR \ - (CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE) /* Env */ -#endif - -/* - * Init Memory Controller: - * - * BR0/1 and OR0/1 (FLASH) - */ - -#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */ -#define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */ - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in data cache) - */ -/* use on chip memory ( OCM ) for temperary stack until sdram is tested */ -#define CONFIG_SYS_TEMP_STACK_OCM 1 - -/* On Chip Memory location */ -#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 -#define CONFIG_SYS_OCM_DATA_SIZE 0x1000 -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */ -#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * External Bus Controller (EBC) Setup - */ - -/* Memory Bank 0 (Flash/SRAM) initialization */ -#define CONFIG_SYS_EBC_PB0AP 0x04006000 -#define CONFIG_SYS_EBC_PB0CR 0xFFF18000 /* BAS=0xFFF,BS=1MB,BU=R/W,BW=8bit */ - -/* Memory Bank 1 (NVRAM/RTC) initialization */ -#define CONFIG_SYS_EBC_PB1AP 0x04041000 -#define CONFIG_SYS_EBC_PB1CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */ - -/* Memory Bank 2 (not used) initialization */ -#define CONFIG_SYS_EBC_PB2AP 0x00000000 -#define CONFIG_SYS_EBC_PB2CR 0x00000000 - -/* Memory Bank 2 (not used) initialization */ -#define CONFIG_SYS_EBC_PB3AP 0x00000000 -#define CONFIG_SYS_EBC_PB3CR 0x00000000 - -/* Memory Bank 4 (FPGA regs) initialization */ -#define CONFIG_SYS_EBC_PB4AP 0x01815000 -#define CONFIG_SYS_EBC_PB4CR 0xF0318000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit */ - -/*----------------------------------------------------------------------- - * Definitions for Serial Presence Detect EEPROM address - * (to get SDRAM settings) - */ -#define SPD_EEPROM_ADDRESS 0x55 - -/*----------------------------------------------------------------------- - * Definitions for GPIO setup (PPC405EP specific) - * - * GPIO0[0] - External Bus Controller BLAST output - * GPIO0[1-9] - Instruction trace outputs - * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs - * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs - * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs - * GPIO0[24-27] - UART0 control signal inputs/outputs - * GPIO0[28-29] - UART1 data signal input/output - * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs - */ -#define CONFIG_SYS_GPIO0_OSRL 0x55555555 -#define CONFIG_SYS_GPIO0_OSRH 0x40000110 -#define CONFIG_SYS_GPIO0_ISR1L 0x00000000 -#define CONFIG_SYS_GPIO0_ISR1H 0x15555445 -#define CONFIG_SYS_GPIO0_TSRL 0x00000000 -#define CONFIG_SYS_GPIO0_TSRH 0x00000000 -#define CONFIG_SYS_GPIO0_TCR 0xFFFF8014 - -/*----------------------------------------------------------------------- - * Some BUBINGA stuff... - */ -#define NVRAM_BASE 0xF0000000 -#define FPGA_REG0 0xF0300000 /* FPGA Reg 0 */ -#define FPGA_REG1 0xF0300001 /* FPGA Reg 1 */ -#define NVRVFY1 0x4f532d4f /* used to determine if state data in */ -#define NVRVFY2 0x50454e00 /* NVRAM initialized (ascii for OS-OPEN)*/ - -#define FPGA_REG0_F_RANGE 0x80 /* SDRAM PLL freq range */ -#define FPGA_REG0_EXT_INT_DIS 0x20 /* External interface disable */ -#define FPGA_REG0_LED_MASK 0x07 /* Board LEDs DS9, DS10, and DS11 */ -#define FPGA_REG0_LED0 0x04 /* Turn on LED0 */ -#define FPGA_REG0_LED1 0x02 /* Turn on LED1 */ -#define FPGA_REG0_LED2 0x01 /* Turn on LED2 */ - -#define FPGA_REG1_SSPEC_DIS 0x80 /* C9531 Spread Spectrum disabled */ -#define FPGA_REG1_OFFBD_PCICLK 0x40 /* Onboard PCI clock selected */ -#define FPGA_REG1_CLOCK_MASK 0x30 /* Mask for C9531 output freq select */ -#define FPGA_REG1_CLOCK_BIT_SHIFT 4 -#define FPGA_REG1_PCI_INT_ARB 0x08 /* PCI Internal arbiter selected */ -#define FPGA_REG1_PCI_FREQ 0x04 /* PCI Frequency select */ -#define FPGA_REG1_OFFB_FLASH 0x02 /* Off board flash */ -#define FPGA_REG1_SRAM_BOOT 0x01 /* SRAM at 0xFFF80000 not Flash */ - -#endif /* __CONFIG_H */ |