diff options
Diffstat (limited to 'include/configs/barco.h')
| -rw-r--r-- | include/configs/barco.h | 228 |
1 files changed, 114 insertions, 114 deletions
diff --git a/include/configs/barco.h b/include/configs/barco.h index 9afb10edc6f..e00f84aab4c 100644 --- a/include/configs/barco.h +++ b/include/configs/barco.h @@ -102,14 +102,14 @@ /* * Miscellaneous configurable options */ -#define CFG_LONGHELP 1 /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_LOAD_ADDR 0x00100000 /* default load address */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_SYS_LONGHELP 1 /* undef to save memory */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ /*----------------------------------------------------------------------- @@ -128,58 +128,58 @@ /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) - * Please note that CFG_SDRAM_BASE _must_ start at 0 + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ -#define CFG_SDRAM_BASE 0x00000000 -#define CFG_MAX_RAM_SIZE 0x02000000 +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_MAX_RAM_SIZE 0x02000000 #define CONFIG_LOGBUFFER #ifdef CONFIG_LOGBUFFER -#define CFG_STDOUT_ADDR 0x1FFC000 +#define CONFIG_SYS_STDOUT_ADDR 0x1FFC000 #else -#define CFG_STDOUT_ADDR 0x2B9000 +#define CONFIG_SYS_STDOUT_ADDR 0x2B9000 #endif -#define CFG_RESET_ADDRESS 0xFFF00100 +#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100 #if defined (USE_DINK32) -#define CFG_MONITOR_LEN 0x00030000 -#define CFG_MONITOR_BASE 0x00090000 -#define CFG_RAMBOOT 1 -#define CFG_INIT_RAM_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN) -#define CFG_INIT_RAM_END 0x10000 -#define CFG_GBL_DATA_SIZE 256 /* size in bytes reserved for initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_MONITOR_LEN 0x00030000 +#define CONFIG_SYS_MONITOR_BASE 0x00090000 +#define CONFIG_SYS_RAMBOOT 1 +#define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) +#define CONFIG_SYS_INIT_RAM_END 0x10000 +#define CONFIG_SYS_GBL_DATA_SIZE 256 /* size in bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET #else -#undef CFG_RAMBOOT -#define CFG_MONITOR_LEN 0x00030000 -#define CFG_MONITOR_BASE TEXT_BASE +#undef CONFIG_SYS_RAMBOOT +#define CONFIG_SYS_MONITOR_LEN 0x00030000 +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE -#define CFG_GBL_DATA_SIZE 128 +#define CONFIG_SYS_GBL_DATA_SIZE 128 -#define CFG_INIT_RAM_ADDR 0x40000000 -#define CFG_INIT_RAM_END 0x1000 -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000 +#define CONFIG_SYS_INIT_RAM_END 0x1000 +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) #endif -#define CFG_FLASH_BASE 0xFFF00000 -#define CFG_FLASH_SIZE (8 * 1024 * 1024) /* Unity has onboard 1MByte flash */ +#define CONFIG_SYS_FLASH_BASE 0xFFF00000 +#define CONFIG_SYS_FLASH_SIZE (8 * 1024 * 1024) /* Unity has onboard 1MByte flash */ #define CONFIG_ENV_IS_IN_FLASH 1 #define CONFIG_ENV_OFFSET 0x000047A4 /* Offset of Environment Sector */ #define CONFIG_ENV_SIZE 0x00002000 /* Total Size of Environment Sector */ /* #define ENV_CRC 0x8BF6F24B XXX - FIXME: gets defined automatically */ -#define CFG_MALLOC_LEN (512 << 10) /* Reserve 512 kB for malloc() */ +#define CONFIG_SYS_MALLOC_LEN (512 << 10) /* Reserve 512 kB for malloc() */ -#define CFG_MEMTEST_START 0x00000000 /* memtest works on */ -#define CFG_MEMTEST_END 0x04000000 /* 0 ... 32 MB in DRAM */ +#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x04000000 /* 0 ... 32 MB in DRAM */ -#define CFG_EUMB_ADDR 0xFDF00000 +#define CONFIG_SYS_EUMB_ADDR 0xFDF00000 -#define CFG_FLASH_RANGE_BASE 0xFFC00000 /* flash memory address range */ -#define CFG_FLASH_RANGE_SIZE 0x00400000 +#define CONFIG_SYS_FLASH_RANGE_BASE 0xFFC00000 /* flash memory address range */ +#define CONFIG_SYS_FLASH_RANGE_SIZE 0x00400000 #define FLASH_BASE0_PRELIM 0xFFF00000 /* sandpoint flash */ #define FLASH_BASE1_PRELIM 0xFF000000 /* PMC onboard flash */ @@ -192,8 +192,8 @@ */ #define CONFIG_HARD_I2C 1 /* To enable I2C support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F #ifdef CONFIG_SOFT_I2C #error "Soft I2C is not configured properly. Please review!" @@ -208,14 +208,14 @@ #define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ #endif /* CONFIG_SOFT_I2C */ -#define CFG_I2C_EEPROM_ADDR 0x57 /* EEPROM IS24C02 */ -#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ -#define CFG_EEPROM_PAGE_WRITE_BITS 3 -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 /* EEPROM IS24C02 */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ -#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } -#define CFG_FLASH_BANKS { FLASH_BASE0_PRELIM , FLASH_BASE1_PRELIM } -#define CFG_DBUS_SIZE2 1 +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } +#define CONFIG_SYS_FLASH_BANKS { FLASH_BASE0_PRELIM , FLASH_BASE1_PRELIM } +#define CONFIG_SYS_DBUS_SIZE2 1 /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in DPRAM) @@ -233,24 +233,24 @@ #define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ -#define CFG_ROMNAL 0x0F /*rom/flash next access time */ -#define CFG_ROMFAL 0x1E /*rom/flash access time */ +#define CONFIG_SYS_ROMNAL 0x0F /*rom/flash next access time */ +#define CONFIG_SYS_ROMFAL 0x1E /*rom/flash access time */ -#define CFG_REFINT 0x8F /* no of clock cycles between CBR refresh cycles */ +#define CONFIG_SYS_REFINT 0x8F /* no of clock cycles between CBR refresh cycles */ /* the following are for SDRAM only*/ -#define CFG_BSTOPRE 0x25C /* Burst To Precharge, sets open page interval */ -#define CFG_REFREC 8 /* Refresh to activate interval */ -#define CFG_RDLAT 4 /* data latency from read command */ -#define CFG_PRETOACT 3 /* Precharge to activate interval */ -#define CFG_ACTTOPRE 5 /* Activate to Precharge interval */ -#define CFG_ACTORW 2 /* Activate to R/W */ -#define CFG_SDMODE_CAS_LAT 3 /* SDMODE CAS latency */ -#define CFG_SDMODE_WRAP 0 /* SDMODE wrap type */ +#define CONFIG_SYS_BSTOPRE 0x25C /* Burst To Precharge, sets open page interval */ +#define CONFIG_SYS_REFREC 8 /* Refresh to activate interval */ +#define CONFIG_SYS_RDLAT 4 /* data latency from read command */ +#define CONFIG_SYS_PRETOACT 3 /* Precharge to activate interval */ +#define CONFIG_SYS_ACTTOPRE 5 /* Activate to Precharge interval */ +#define CONFIG_SYS_ACTORW 2 /* Activate to R/W */ +#define CONFIG_SYS_SDMODE_CAS_LAT 3 /* SDMODE CAS latency */ +#define CONFIG_SYS_SDMODE_WRAP 0 /* SDMODE wrap type */ -#define CFG_REGISTERD_TYPE_BUFFER 1 -#define CFG_EXTROM 0 -#define CFG_REGDIMM 0 +#define CONFIG_SYS_REGISTERD_TYPE_BUFFER 1 +#define CONFIG_SYS_EXTROM 0 +#define CONFIG_SYS_REGDIMM 0 /* memory bank settings*/ @@ -260,95 +260,95 @@ * bits will be set to 0x00000 for a start address, or 0xfffff for an * end address */ -#define CFG_BANK0_START 0x00000000 -#define CFG_BANK0_END 0x01FFFFFF -#define CFG_BANK0_ENABLE 1 -#define CFG_BANK1_START 0x02000000 -#define CFG_BANK1_END 0x02ffffff -#define CFG_BANK1_ENABLE 0 -#define CFG_BANK2_START 0x03f00000 -#define CFG_BANK2_END 0x03ffffff -#define CFG_BANK2_ENABLE 0 -#define CFG_BANK3_START 0x04000000 -#define CFG_BANK3_END 0x04ffffff -#define CFG_BANK3_ENABLE 0 -#define CFG_BANK4_START 0x05000000 -#define CFG_BANK4_END 0x05FFFFFF -#define CFG_BANK4_ENABLE 0 -#define CFG_BANK5_START 0x06000000 -#define CFG_BANK5_END 0x06FFFFFF -#define CFG_BANK5_ENABLE 0 -#define CFG_BANK6_START 0x07000000 -#define CFG_BANK6_END 0x07FFFFFF -#define CFG_BANK6_ENABLE 0 -#define CFG_BANK7_START 0x08000000 -#define CFG_BANK7_END 0x08FFFFFF -#define CFG_BANK7_ENABLE 0 +#define CONFIG_SYS_BANK0_START 0x00000000 +#define CONFIG_SYS_BANK0_END 0x01FFFFFF +#define CONFIG_SYS_BANK0_ENABLE 1 +#define CONFIG_SYS_BANK1_START 0x02000000 +#define CONFIG_SYS_BANK1_END 0x02ffffff +#define CONFIG_SYS_BANK1_ENABLE 0 +#define CONFIG_SYS_BANK2_START 0x03f00000 +#define CONFIG_SYS_BANK2_END 0x03ffffff +#define CONFIG_SYS_BANK2_ENABLE 0 +#define CONFIG_SYS_BANK3_START 0x04000000 +#define CONFIG_SYS_BANK3_END 0x04ffffff +#define CONFIG_SYS_BANK3_ENABLE 0 +#define CONFIG_SYS_BANK4_START 0x05000000 +#define CONFIG_SYS_BANK4_END 0x05FFFFFF +#define CONFIG_SYS_BANK4_ENABLE 0 +#define CONFIG_SYS_BANK5_START 0x06000000 +#define CONFIG_SYS_BANK5_END 0x06FFFFFF +#define CONFIG_SYS_BANK5_ENABLE 0 +#define CONFIG_SYS_BANK6_START 0x07000000 +#define CONFIG_SYS_BANK6_END 0x07FFFFFF +#define CONFIG_SYS_BANK6_ENABLE 0 +#define CONFIG_SYS_BANK7_START 0x08000000 +#define CONFIG_SYS_BANK7_END 0x08FFFFFF +#define CONFIG_SYS_BANK7_ENABLE 0 /* * Memory bank enable bitmask, specifying which of the banks defined above are actually present. MSB is for bank #7, LSB is for bank #0. */ -#define CFG_BANK_ENABLE 0x01 +#define CONFIG_SYS_BANK_ENABLE 0x01 -#define CFG_ODCR 0xff /* configures line driver impedances, */ +#define CONFIG_SYS_ODCR 0xff /* configures line driver impedances, */ /* see 8240 book for bit definitions */ -#define CFG_PGMAX 0x32 /* how long the 8240 retains the */ +#define CONFIG_SYS_PGMAX 0x32 /* how long the 8240 retains the */ /* currently accessed page in memory */ /* see 8240 book for details */ /* SDRAM 0 - 256MB */ -#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) -#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) /* stack in DCACHE @ 1GB (no backing mem) */ #if defined(USE_DINK32) -#define CFG_IBAT1L (0x40000000 | BATL_PP_00 ) -#define CFG_IBAT1U (0x40000000 | BATU_BL_128K ) +#define CONFIG_SYS_IBAT1L (0x40000000 | BATL_PP_00 ) +#define CONFIG_SYS_IBAT1U (0x40000000 | BATU_BL_128K ) #else -#define CFG_IBAT1L (CFG_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE) -#define CFG_IBAT1U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) #endif /* PCI memory */ -#define CFG_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT) -#define CFG_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT) +#define CONFIG_SYS_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP) /* Flash, config addrs, etc */ -#define CFG_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT) -#define CFG_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP) - -#define CFG_DBAT0L CFG_IBAT0L -#define CFG_DBAT0U CFG_IBAT0U -#define CFG_DBAT1L CFG_IBAT1L -#define CFG_DBAT1U CFG_IBAT1U -#define CFG_DBAT2L CFG_IBAT2L -#define CFG_DBAT2U CFG_IBAT2U -#define CFG_DBAT3L CFG_IBAT3L -#define CFG_DBAT3U CFG_IBAT3U +#define CONFIG_SYS_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT) +#define CONFIG_SYS_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP) + +#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L +#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U +#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L +#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U +#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L +#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U +#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L +#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization */ -#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CFG_MAX_FLASH_SECT 20 /* max number of sectors on one chip */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 20 /* max number of sectors on one chip */ -#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ -#define CFG_FLASH_CHECKSUM +#define CONFIG_SYS_FLASH_CHECKSUM /*----------------------------------------------------------------------- * Cache Configuration */ -#define CFG_CACHELINE_SIZE 32 /* For MPC8240 CPU */ +#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8240 CPU */ #if defined(CONFIG_CMD_KGDB) -# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ #endif |