diff options
Diffstat (limited to 'include/configs/bamboo.h')
| -rw-r--r-- | include/configs/bamboo.h | 211 |
1 files changed, 0 insertions, 211 deletions
diff --git a/include/configs/bamboo.h b/include/configs/bamboo.h deleted file mode 100644 index 8868deb1c16..00000000000 --- a/include/configs/bamboo.h +++ /dev/null @@ -1,211 +0,0 @@ -/* - * (C) Copyright 2005-2007 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/************************************************************************ - * bamboo.h - configuration for BAMBOO board - ***********************************************************************/ -#ifndef __CONFIG_H -#define __CONFIG_H - -/*----------------------------------------------------------------------- - * High Level Configuration Options - *----------------------------------------------------------------------*/ -#define CONFIG_BAMBOO 1 /* Board is BAMBOO */ -#define CONFIG_440EP 1 /* Specific PPC440EP support */ -#define CONFIG_440 1 /* ... PPC440 family */ -#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ - -#ifndef CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_TEXT_BASE 0xFFFA0000 -#endif - -/* - * Include common defines/options for all AMCC eval boards - */ -#define CONFIG_HOSTNAME bamboo -#include "amcc-common.h" - -/* Reclaim some space. */ -#undef CONFIG_SYS_LONGHELP - -/* - * Please note that, if NAND support is enabled, the 2nd ethernet port - * can't be used because of pin multiplexing. So, if you want to use the - * 2nd ethernet port you have to "undef" the following define. - */ -#define CONFIG_BAMBOO_NAND 1 /* enable nand flash support */ - -/*----------------------------------------------------------------------- - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_FLASH_BASE 0xfff00000 /* start of FLASH */ -#define CONFIG_SYS_PCI_MEMBASE 0xa0000000 /* mapped pci memory*/ -#define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000 -#define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000 -#define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000 - -/*Don't change either of these*/ -#define CONFIG_SYS_PCI_BASE 0xe0000000 /* internal PCI regs*/ -/*Don't change either of these*/ - -#define CONFIG_SYS_USB_DEVICE 0x50000000 -#define CONFIG_SYS_NVRAM_BASE_ADDR 0x80000000 -#define CONFIG_SYS_BOOT_BASE_ADDR 0xf0000000 -#define CONFIG_SYS_NAND_ADDR 0x90000000 -#define CONFIG_SYS_NAND2_ADDR 0x94000000 - -/*----------------------------------------------------------------------- - * Initial RAM & stack pointer (placed in SDRAM) - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_INIT_RAM_DCACHE 1 /* d-cache as init ram */ -#define CONFIG_SYS_INIT_RAM_ADDR 0x70000000 /* DCache */ -#define CONFIG_SYS_INIT_RAM_SIZE (4 << 10) -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Serial Port - *----------------------------------------------------------------------*/ -#define CONFIG_CONS_INDEX 1 /* Use UART0 */ -#define CONFIG_SYS_EXT_SERIAL_CLOCK 11059200 /* use external 11.059MHz clk */ - -/*----------------------------------------------------------------------- - * NVRAM/RTC - * - * NOTE: The RTC registers are located at 0x7FFF0 - 0x7FFFF - * The DS1558 code assumes this condition - * - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_NVRAM_SIZE (0x2000 - 0x10) /* NVRAM size(8k)- RTC regs */ -#define CONFIG_RTC_DS1556 1 /* DS1556 RTC */ - -/*----------------------------------------------------------------------- - * Environment - *----------------------------------------------------------------------*/ -#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ - -/*----------------------------------------------------------------------- - * FLASH related - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_MAX_FLASH_BANKS 3 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 256 /* sectors per device */ - -#undef CONFIG_SYS_FLASH_CHECKSUM -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -#define CONFIG_SYS_FLASH_ADDR0 0x555 -#define CONFIG_SYS_FLASH_ADDR1 0x2aa -#define CONFIG_SYS_FLASH_WORD_SIZE unsigned char - -#define CONFIG_SYS_FLASH_2ND_16BIT_DEV 1 /* bamboo has 8 and 16bit device */ -#define CONFIG_SYS_FLASH_2ND_ADDR 0x87800000 /* bamboo has 8 and 16bit device */ - -#ifdef CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ -#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) -#endif /* CONFIG_ENV_IS_IN_FLASH */ - -/*----------------------------------------------------------------------- - * NAND FLASH - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_MAX_NAND_DEVICE 2 -#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_ADDR + CONFIG_SYS_NAND_CS) -#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_ADDR + 2 } -#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ -#define CONFIG_SYS_NAND_CS 1 - -/*----------------------------------------------------------------------- - * DDR SDRAM - *----------------------------------------------------------------------------- */ -#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */ -#undef CONFIG_DDR_ECC /* don't use ECC */ -#define CONFIG_SYS_SIMULATE_SPD_EEPROM 0xff /* simulate spd eeprom on this address */ -#define SPD_EEPROM_ADDRESS {CONFIG_SYS_SIMULATE_SPD_EEPROM, 0x50, 0x51} -#define CONFIG_SYS_MBYTES_SDRAM (64) /* 64MB fixed size for early-sdram-init */ -#define CONFIG_PROG_SDRAM_TLB - -/*----------------------------------------------------------------------- - * I2C - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 - -#define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1) -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 - -#ifdef CONFIG_ENV_IS_IN_EEPROM -#define CONFIG_ENV_SIZE 0x200 /* Size of Environment vars */ -#define CONFIG_ENV_OFFSET 0x0 -#endif /* CONFIG_ENV_IS_IN_EEPROM */ - -/* - * Default environment variables - */ -#define CONFIG_EXTRA_ENV_SETTINGS \ - CONFIG_AMCC_DEF_ENV \ - CONFIG_AMCC_DEF_ENV_POWERPC \ - CONFIG_AMCC_DEF_ENV_PPC_OLD \ - CONFIG_AMCC_DEF_ENV_NOR_UPD \ - "kernel_addr=fff00000\0" \ - "ramdisk_addr=fff10000\0" \ - "" - -#define CONFIG_HAS_ETH0 -#define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */ -#define CONFIG_PHY1_ADDR 1 - -#ifndef CONFIG_BAMBOO_NAND -#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ -#endif /* CONFIG_BAMBOO_NAND */ - -#ifdef CONFIG_440EP -/* USB */ -#define CONFIG_USB_OHCI - -/*Comment this out to enable USB 1.1 device*/ -#define USB_2_0_DEVICE -#endif /*CONFIG_440EP*/ - -/* - * Commands additional to the ones defined in amcc-common.h - */ -#define CONFIG_CMD_PCI -#define CONFIG_CMD_SDRAM - -#ifdef CONFIG_BAMBOO_NAND -#define CONFIG_CMD_NAND -#endif - -#define CONFIG_SUPPORT_VFAT - -/* Partitions */ - -/*----------------------------------------------------------------------- - * PCI stuff - *----------------------------------------------------------------------- - */ -/* General PCI */ -#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ -#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE*/ - -/* Board-specific PCI */ -#define CONFIG_SYS_PCI_TARGET_INIT -#define CONFIG_SYS_PCI_MASTER_INIT - -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ -#define CONFIG_SYS_PCI_SUBSYS_ID 0xcafe /* Whatever */ - -#endif /* __CONFIG_H */ |