diff options
Diffstat (limited to 'include/configs/aev.h')
-rw-r--r-- | include/configs/aev.h | 79 |
1 files changed, 43 insertions, 36 deletions
diff --git a/include/configs/aev.h b/include/configs/aev.h index 8d9f0a16610..5bab793e9cc 100644 --- a/include/configs/aev.h +++ b/include/configs/aev.h @@ -44,11 +44,6 @@ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ -#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) -# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* * Serial console configuration */ @@ -91,34 +86,42 @@ CFG_POST_I2C) #ifdef CONFIG_POST -#define CFG_CMD_POST_DIAG CFG_CMD_DIAG /* preserve space for the post_word at end of on-chip SRAM */ #define MPC5XXX_SRAM_POST_SIZE MPC5XXX_SRAM_SIZE-4 -#else -#define CFG_CMD_POST_DIAG 0 #endif + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + /* - * Supported commands + * Command line configuration. */ -#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ - ADD_BMP_CMD | \ - CFG_CMD_PCI | \ - CFG_CMD_ASKENV | \ - CFG_CMD_DATE | \ - CFG_CMD_DHCP | \ - CFG_CMD_ECHO | \ - CFG_CMD_EEPROM | \ - CFG_CMD_I2C | \ - CFG_CMD_MII | \ - CFG_CMD_NFS | \ - CFG_CMD_PING | \ - CFG_CMD_POST_DIAG | \ - CFG_CMD_REGINFO | \ - CFG_CMD_SNTP ) - -/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ -#include <cmd_confdefs.h> +#include <config_cmd_default.h> + +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_ECHO +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_NFS +#define CONFIG_CMD_PCI +#define CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO +#define CONFIG_CMD_SNTP + +#ifdef CONFIG_POST +#define CONFIG_CMD_DIAG +#endif + #define CONFIG_TIMESTAMP /* display image timestamps */ @@ -166,17 +169,17 @@ /* * IPB Bus clocking configuration. */ -#define CFG_IPBSPEED_133 /* define for 133MHz speed */ +#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ -#if defined(CFG_IPBSPEED_133) +#if defined(CFG_IPBCLK_EQUALS_XLBCLK) /* * PCI Bus clocking configuration * * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if - * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet hasn't - * been tested with a IPB Bus Clock of 66 MHz. + * CFG_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock + * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz. */ -#define CFG_PCISPEED_66 /* define for 66MHz speed */ +#define CFG_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */ #endif /* @@ -324,7 +327,7 @@ */ #define CFG_LONGHELP /* undef to save memory */ #define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ @@ -343,9 +346,13 @@ #define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ +#if defined(CONFIG_CMD_KGDB) +# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + /* - * Enable loopw commando. This has only affect, if CFG_CMD_MEM is defined, - * which is normally part of the default commands (CFV_CMD_DFL) + * Enable loopw command. */ #define CONFIG_LOOPW @@ -362,7 +369,7 @@ #define CFG_BOOTCS_START CFG_FLASH_BASE #define CFG_BOOTCS_SIZE CFG_FLASH_SIZE -#ifdef CFG_PCISPEED_66 +#ifdef CFG_PCICLK_EQUALS_IPBCLK_DIV2 #define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */ #else #define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */ |