diff options
Diffstat (limited to 'include/configs/RPXlite_DW.h')
| -rw-r--r-- | include/configs/RPXlite_DW.h | 462 |
1 files changed, 0 insertions, 462 deletions
diff --git a/include/configs/RPXlite_DW.h b/include/configs/RPXlite_DW.h deleted file mode 100644 index 50c82c68eb..0000000000 --- a/include/configs/RPXlite_DW.h +++ /dev/null @@ -1,462 +0,0 @@ -/* - * (C) Copyright 2004 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * Sam Song, IEMC. SHU, samsongshu@yahoo.com.cn - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config.h - configuration options, board specific - */ - -/* Yoo. Jonghoon, IPone, yooth@ipone.co.kr - * U-BOOT port on RPXlite board - */ - -/* - * Sam Song, IEMC. SHU, samsongshu@yahoo.com.cn - * U-BOOT port on RPXlite DW version board--RPXlite_DW - * June 8 ,2004 - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -/* #define DEBUG 1 */ -/* #define DEPLOYMENT 1 */ - -#undef CONFIG_MPC860 -#define CONFIG_MPC823 1 /* This is a MPC823e CPU. */ -#define CONFIG_RPXLITE 1 /* RPXlite DW version board */ - -#define CONFIG_SYS_TEXT_BASE 0xff000000 - -#ifdef CONFIG_LCD /* with LCD controller ? */ -#define CONFIG_MPC8XX_LCD -#define CONFIG_SPLASH_SCREEN /* ... with splashscreen support*/ -#endif - -#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ -#undef CONFIG_8xx_CONS_SMC2 -#undef CONFIG_8xx_CONS_NONE -#define CONFIG_BAUDRATE 9600 /* console default baudrate = 9600bps */ - -#ifdef DEBUG -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 6 /* autoboot after 6 seconds */ - -#ifdef DEPLOYMENT -#define CONFIG_BOOT_RETRY_TIME -1 -#define CONFIG_AUTOBOOT_KEYED -#define CONFIG_AUTOBOOT_PROMPT \ - "autoboot in %d seconds (stop with 'st')...\n", bootdelay -#define CONFIG_AUTOBOOT_STOP_STR "st" -#define CONFIG_ZERO_BOOTDELAY_CHECK -#define CONFIG_RESET_TO_RETRY 1 -#define CONFIG_BOOT_RETRY_MIN 1 -#endif /* DEPLOYMENT */ -#endif /* DEBUG */ - -/* pre-boot commands */ -#define CONFIG_PREBOOT "setenv stdout serial;setenv stdin serial" - -#undef CONFIG_BOOTARGS -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "nfsargs=setenv bootargs console=tty0 console=ttyS0,9600 " \ - "root=/dev/nfs rw nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs console=tty0 root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "flash_nfs=run nfsargs addip;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ - "gatewayip=172.16.115.254\0" \ - "netmask=255.255.255.0\0" \ - "kernel_addr=ff040000\0" \ - "ramdisk_addr=ff200000\0" \ - "ku=era ${kernel_addr} ff1fffff;cp.b 100000 ${kernel_addr} " \ - "${filesize};md ${kernel_addr};" \ - "echo kernel updating finished\0" \ - "uu=protect off 1:0-4;era 1:0-4;cp.b 100000 ff000000 " \ - "${filesize};md ff000000;" \ - "echo u-boot updating finished\0" \ - "eu=protect off 1:6;era 1:6;reset\0" \ - "lcd=setenv stdout lcd;setenv stdin lcd\0" \ - "ser=setenv stdout serial;setenv stdin serial\0" \ - "verify=no" - -#define CONFIG_BOOTCOMMAND "run flash_self" - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ -#undef CONFIG_WATCHDOG /* watchdog disabled */ -#undef CONFIG_STATUS_LED /* disturbs display. Status LED disabled. */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_BOOTFILESIZE - - -#if 1 /* Enable this stuff could make image enlarge about 25KB. Mask it if you - don't want the advanced function */ - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_JFFS2 -#define CONFIG_CMD_PING -#define CONFIG_CMD_ELF -#define CONFIG_CMD_REGINFO -#define CONFIG_CMD_DHCP - -#ifdef CONFIG_SPLASH_SCREEN -#define CONFIG_CMD_BMP -#endif - - -/* test-only */ -#define CONFIG_SYS_JFFS2_FIRST_BANK 0 /* use for JFFS2 */ -#define CONFIG_SYS_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */ - -#define CONFIG_NETCONSOLE - -#endif /* 1 */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT "u-boot>" /* Monitor Command Prompt */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif - -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x0040000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00C0000 /* 4 ... 12 MB in DRAM */ -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ -/*----------------------------------------------------------------------- - * Internal Memory Mapped Register - */ -#define CONFIG_SYS_IMMR 0xFA200000 - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0xFF000000 - -#if defined(DEBUG) || defined(CONFIG_CMD_IDE) -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#else -#define CONFIG_SYS_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */ -#endif - -#define CONFIG_SYS_MONITOR_BASE 0xFF000000 -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 71 /* max number of sectors on one chip */ -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -#ifdef CONFIG_ENV_IS_IN_NVRAM -#define CONFIG_ENV_ADDR 0xFA000100 -#define CONFIG_ENV_SIZE 0x1000 -#else -#define CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_OFFSET 0x30000 /* Offset of Environment Sector */ -#define CONFIG_ENV_SIZE 0x8000 /* Total Size of Environment Sector */ -#endif /* CONFIG_ENV_IS_IN_NVRAM */ - -#define CONFIG_SYS_RESET_ADDRESS ((ulong)((((immap_t *)CONFIG_SYS_IMMR)->im_clkrst.res))) - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ -#endif - -/*----------------------------------------------------------------------- - * SYPCR - System Protection Control 32-bit 12-35 - * SYPCR can only be written once after reset! - *----------------------------------------------------------------------- - * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze - */ -#if defined(CONFIG_WATCHDOG) -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ - SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) -#else -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | 0x00000600 | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) -#endif /* We can get SYPCR: 0xFFFF0689. */ - -/*----------------------------------------------------------------------- - * SIUMCR - SIU Module Configuration 32-bit 12-30 - *----------------------------------------------------------------------- - * PCMCIA config., multi-function pin tri-state - */ -#define CONFIG_SYS_SIUMCR (SIUMCR_MLRC10) /* SIUMCR:0x00000800 */ - -/*--------------------------------------------------------------------- - * TBSCR - Time Base Status and Control 16-bit 12-16 - *--------------------------------------------------------------------- - * Clear Reference Interrupt Status, Timebase freezing enabled - */ -#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF | TBSCR_TBE) -/* TBSCR: 0x00C3 [SAM] */ - -/*----------------------------------------------------------------------- - * RTCSC - Real-Time Clock Status and Control Register 16-bit 12-18 - *----------------------------------------------------------------------- - * [RTC enabled but not stopped on FRZ] - */ -#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTE) /* RTCSC:0x00C1 */ - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control 16-bit 12-23 - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled - * [Periodic timer enabled,Periodic timer interrupt disable. ] - */ -#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF | PISCR_PTE) /* PISCR:0x0083 */ - -/*----------------------------------------------------------------------- - * PLPRCR - PLL, Low-Power, and Reset Control Register 32-bit 5-7 - *----------------------------------------------------------------------- - * Reset PLL lock status sticky bit, timer expired status bit and timer - * interrupt status bit - */ -/* up to 64 MHz we use a 1:2 clock */ -#if defined(RPXlite_64MHz) -#define CONFIG_SYS_PLPRCR ( (7 << PLPRCR_MF_SHIFT) | PLPRCR_TEXPS ) /*PLPRCR: 0x00700000. */ -#else -#define CONFIG_SYS_PLPRCR ( (5 << PLPRCR_MF_SHIFT) | PLPRCR_TEXPS ) -#endif - -/*----------------------------------------------------------------------- - * SCCR - System Clock and reset Control Register 5-3 - *----------------------------------------------------------------------- - * Set clock output, timebase and RTC source and divider, - * power management and some other internal clocks - */ -#define SCCR_MASK SCCR_EBDF00 -/* Up to 48MHz system clock, we use 1:1 SYSTEM/BUS ratio */ -#if defined(RPXlite_64MHz) -#define CONFIG_SYS_SCCR ( SCCR_TBS | SCCR_EBDF01 ) /* %%%SCCR:0x02020000 */ -#else -#define CONFIG_SYS_SCCR ( SCCR_TBS | SCCR_EBDF00 ) /* %%%SCCR:0x02000000 */ -#endif - -/*----------------------------------------------------------------------- - * PCMCIA stuff - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000) -#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 ) -#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000) -#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 ) -#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000) -#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 ) -#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000) -#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 ) - -/*----------------------------------------------------------------------- - * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter) - *----------------------------------------------------------------------- - */ -#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */ -#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */ - -#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ -#undef CONFIG_IDE_LED /* LED for ide not supported */ -#undef CONFIG_IDE_RESET /* reset for ide not supported */ - -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ -#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ - -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 -#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR - -/* Offset for data I/O */ -#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320) - -/* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320) - -/* Offset for alternate registers */ -#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100 - -#define CONFIG_SYS_DER 0 - -/* - * Init Memory Controller: - * - * BR0 and OR0 (FLASH) - */ -#define FLASH_BASE_PRELIM 0xFC000000 /* FLASH base */ -#define CONFIG_SYS_PRELIM_OR_AM 0xFC000000 /* OR addr mask */ - -/* FLASH timing: ACS = 0, TRLX = 0, CSNT = 0, SCY = 8, ETHR = 0, BIH = 1 */ -#define CONFIG_SYS_OR_TIMING_FLASH (OR_SCY_8_CLK | OR_BI) -#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) -#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE_PRELIM & BR_BA_MSK) | BR_V) - -/* - * BR1 and OR1 (SDRAM) - * - */ -#define SDRAM_BASE_PRELIM 0x00000000 /* SDRAM base */ -#define SDRAM_MAX_SIZE 0x08000000 /* max 128 MB in system */ - -/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */ -#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000E00 -#define CONFIG_SYS_OR_AM_SDRAM (-(SDRAM_MAX_SIZE & OR_AM_MSK)) -#define CONFIG_SYS_OR1_PRELIM ( CONFIG_SYS_OR_AM_SDRAM | CONFIG_SYS_OR_TIMING_SDRAM ) -#define CONFIG_SYS_BR1_PRELIM ((SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V ) - -/* RPXlite mem setting */ -#define CONFIG_SYS_BR3_PRELIM 0xFA400001 /* BCSR */ -#define CONFIG_SYS_OR3_PRELIM 0xFF7F8900 -#define CONFIG_SYS_BR4_PRELIM 0xFA000401 /* NVRAM&SRAM */ -#define CONFIG_SYS_OR4_PRELIM 0xFFFE0040 - -/* - * Memory Periodic Timer Prescaler - */ -/* periodic timer for refresh */ -#if defined(RPXlite_64MHz) -#define CONFIG_SYS_MAMR_PTA 32 -#else -#define CONFIG_SYS_MAMR_PTA 20 -#endif - -/* - * Refresh clock Prescalar - */ -#define CONFIG_SYS_MPTPR MPTPR_PTP_DIV2 - -/* - * MAMR settings for SDRAM - */ - -/* 9 column SDRAM */ -#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ - MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10) -/* CONFIG_SYS_MAMR_9COL:0x20904000 @ 64MHz */ - -/*%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% */ -/* Configuration variable added by yooth. */ -/*%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% */ -/* - * BCSRx - * - * Board Status and Control Registers - * - */ -#define BCSR0 0xFA400000 -#define BCSR1 0xFA400001 -#define BCSR2 0xFA400002 -#define BCSR3 0xFA400003 - -#define BCSR0_ENMONXCVR 0x01 /* Monitor XVCR Control */ -#define BCSR0_ENNVRAM 0x02 /* CS4# Control */ -#define BCSR0_LED5 0x04 /* LED5 control 0='on' 1='off' */ -#define BCSR0_LED4 0x08 /* LED4 control 0='on' 1='off' */ -#define BCSR0_FULLDPLX 0x10 /* Ethernet XCVR Control */ -#define BCSR0_COLTEST 0x20 -#define BCSR0_ETHLPBK 0x40 -#define BCSR0_ETHEN 0x80 - -#define BCSR1_PCVCTL7 0x01 /* PC Slot B Control */ -#define BCSR1_PCVCTL6 0x02 -#define BCSR1_PCVCTL5 0x04 -#define BCSR1_PCVCTL4 0x08 -#define BCSR1_IPB5SEL 0x10 - -#define BCSR1_SMC1CTS 0x40 /* Added by SAM. */ -#define BCSR1_SMC1TRS 0x80 /* Added by SAM. */ - -#define BCSR2_ENRTCIRQ 0x01 /* Added by SAM. */ -#define BCSR2_ENBRG1 0x04 /* Added by SAM. */ - -#define BCSR2_ENPA5HDR 0x08 /* USB Control */ -#define BCSR2_ENUSBCLK 0x10 -#define BCSR2_USBPWREN 0x20 -#define BCSR2_USBSPD 0x40 -#define BCSR2_USBSUSP 0x80 - -#define BCSR3_BWKAPWR 0x01 /* Changed by SAM. Backup battery situation */ -#define BCSR3_IRQRTC 0x02 /* Changed by SAM. NVRAM Battery */ -#define BCSR3_RDY_BSY 0x04 /* Changed by SAM. Flash Operation */ -#define BCSR3_MPLX_LIN 0x08 /* Changed by SAM. Linear or Multiplexed address Mode */ - -#define BCSR3_D27 0x10 /* Dip Switch settings */ -#define BCSR3_D26 0x20 -#define BCSR3_D25 0x40 -#define BCSR3_D24 0x80 - -/* - * Environment setting - */ -#define CONFIG_ETHADDR 00:10:EC:00:37:5B -#define CONFIG_IPADDR 172.16.115.7 -#define CONFIG_SERVERIP 172.16.115.6 -#define CONFIG_ROOTPATH "/workspace/myfilesystem/target/" -#define CONFIG_BOOTFILE "uImage.rpxusb" -#define CONFIG_HOSTNAME LITE_H1_DW - -#endif /* __CONFIG_H */ |