diff options
Diffstat (limited to 'include/configs/PIP405.h')
| -rw-r--r-- | include/configs/PIP405.h | 305 |
1 files changed, 0 insertions, 305 deletions
diff --git a/include/configs/PIP405.h b/include/configs/PIP405.h deleted file mode 100644 index 1f5b9f045f..0000000000 --- a/include/configs/PIP405.h +++ /dev/null @@ -1,305 +0,0 @@ -/* - * (C) Copyright 2001 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/*********************************************************** - * High Level Configuration Options - * (easy to change) - ***********************************************************/ -#define CONFIG_405GP 1 /* This is a PPC405 CPU */ -#define CONFIG_PIP405 1 /* ...on a PIP405 board */ - -#define CONFIG_SYS_TEXT_BASE 0xFFF80000 - -/*********************************************************** - * Clock - ***********************************************************/ -#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - -/* - * Command line configuration. - */ -#define CONFIG_CMD_PCI -#define CONFIG_CMD_REGINFO -#define CONFIG_SCSI -#define CONFIG_CMD_SDRAM -#define CONFIG_CMD_SAVES - -/************************************************************** - * I2C Stuff: - * the PIP405 is equiped with an Atmel 24C128/256 EEPROM at address - * 0x53. - * Caution: on the same bus is the SPD (Serial Presens Detect - * EEPROM of the SDRAM - * The Atmel EEPROM uses 16Bit addressing. - ***************************************************************/ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_PPC4XX -#define CONFIG_SYS_I2C_PPC4XX_CH0 -#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 50000 -#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F - -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x53 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ -#define CONFIG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */ -#define CONFIG_ENV_SIZE 0x800 /* 2 kBytes may be used for env vars */ - -#undef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* The Atmel 24C128/256 has */ - /* 64 byte page write mode using*/ - /* last 6 bits of the address */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ - -/*************************************************************** - * Definitions for Serial Presence Detect EEPROM address - * (to get SDRAM settings) - ***************************************************************/ -#define SPD_EEPROM_ADDRESS 0x50 - -#define CONFIG_BOARD_EARLY_INIT_R - -/************************************************************** - * Environment definitions - **************************************************************/ - -/* autoboot (do NOT change this set environment variable "bootdelay" to -1 instead) */ -/* #define CONFIG_BOOT_RETRY_TIME -10 /XXX* feature is available but not enabled */ - -#define CONFIG_BOOTCOMMAND "diskboot 400000 0:1; bootm" /* autoboot command */ -#define CONFIG_BOOTARGS "console=ttyS0,9600 root=/dev/hda5" /* boot arguments */ - -#define CONFIG_IPADDR 10.0.0.100 -#define CONFIG_SERVERIP 10.0.0.1 -#define CONFIG_PREBOOT -/*************************************************************** - * defines if an overwrite_console function exists - *************************************************************/ -/*************************************************************** - * defines if the overwrite_console should be stored in the - * environment - **************************************************************/ - -/************************************************************** - * loads config - *************************************************************/ -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#define CONFIG_MISC_INIT_R -/*********************************************************** - * Miscellaneous configurable options - **********************************************************/ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x0100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 1 ... 12 MB in DRAM */ - -#define CONFIG_CONS_INDEX 1 /* Use UART0 */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_serial_clock() - -#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ -#define CONFIG_SYS_BASE_BAUD 691200 - -/* The following table includes the supported baudrates */ -#define CONFIG_SYS_BAUDRATE_TABLE \ - { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \ - 57600, 115200, 230400, 460800, 921600 } - -#define CONFIG_SYS_LOAD_ADDR 0x400000 /* default load address */ -#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -/*----------------------------------------------------------------------- - * PCI stuff - *----------------------------------------------------------------------- - */ -#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */ -#define PCI_HOST_FORCE 1 /* configure as pci host */ -#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ - -#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ -#define CONFIG_PCI_HOST PCI_HOST_FORCE /* configure as pci-host */ - /* resource configuration */ -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */ -#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */ -#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ -#define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */ -#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ -#define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */ -#define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */ -#define CONFIG_SYS_PCI_PTM2PCI 0x00000000 /* Host: use this pci address */ - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0xFFF80000 -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserve 1024 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_UPDATE_FLASH_SIZE -#define CONFIG_SYS_FLASH_PROTECTION -#define CONFIG_SYS_FLASH_EMPTY_INFO - -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_FLASH_CFI_DRIVER - -#define CONFIG_FLASH_SHOW_PROGRESS 45 - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -#define CONFIG_SYS_MAX_FLASH_SECT 256 - -/* - * Init Memory Controller: - */ -#define FLASH_MAX_SIZE 0x00800000 /* 8MByte max */ -#define FLASH_BASE_PRELIM 0xFF800000 /* open the flash CS */ -/* Size: 0=1MB, 1=2MB, 2=4MB, 3=8MB, 4=16MB, 5=32MB, 6=64MB, 7=128MB */ -#define FLASH_SIZE_PRELIM 3 /* maximal flash FLASH size bank #0 */ - -/* Configuration Port location */ -#define CONFIG_PORT_ADDR 0xF4000000 -#define MULTI_PURPOSE_SOCKET_ADDR 0xF8000000 - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in On Chip SRAM) - */ -#define CONFIG_SYS_TEMP_STACK_OCM 1 -#define CONFIG_SYS_OCM_DATA_ADDR 0xF0000000 -#define CONFIG_SYS_OCM_DATA_SIZE 0x1000 -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of On Chip SRAM */ -#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of On Chip SRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*********************************************************************** - * External peripheral base address - ***********************************************************************/ -#define CONFIG_SYS_ISA_IO_BASE_ADDRESS 0xE8000000 - -/*********************************************************************** - * Last Stage Init - ***********************************************************************/ -#define CONFIG_LAST_STAGE_INIT -/************************************************************ - * Ethernet Stuff - ***********************************************************/ -#define CONFIG_PPC4xx_EMAC -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 1 /* PHY address */ -/************************************************************ - * RTC - ***********************************************************/ -#define CONFIG_RTC_MC146818 -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/************************************************************ - * IDE/ATA stuff - ************************************************************/ -#define CONFIG_SYS_IDE_MAXBUS 2 /* max. 2 IDE busses */ -#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */ - -#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_ISA_IO_BASE_ADDRESS /* base address */ -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x01F0 /* ide0 offste */ -#define CONFIG_SYS_ATA_IDE1_OFFSET 0x0170 /* ide1 offset */ -#define CONFIG_SYS_ATA_DATA_OFFSET 0 /* data reg offset */ -#define CONFIG_SYS_ATA_REG_OFFSET 0 /* reg offset */ -#define CONFIG_SYS_ATA_ALT_OFFSET 0x200 /* alternate register offset */ - -#undef CONFIG_IDE_LED /* no led for ide supported */ -#define CONFIG_IDE_RESET /* reset for ide supported... */ -#define CONFIG_IDE_RESET_ROUTINE /* with a special reset function */ -#define CONFIG_SUPPORT_VFAT - -/************************************************************ - * ATAPI support (experimental) - ************************************************************/ -#define CONFIG_ATAPI /* enable ATAPI Support */ - -/************************************************************ - * SCSI support (experimental) only SYM53C8xx supported - ************************************************************/ -#define CONFIG_SCSI_SYM53C8XX -#define CONFIG_SYS_SCSI_MAX_LUN 8 /* number of supported LUNs */ -#define CONFIG_SYS_SCSI_MAX_SCSI_ID 7 /* maximum SCSI ID (0..6) */ -#define CONFIG_SYS_SCSI_MAX_DEVICE CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN /* maximum Target devices */ -#define CONFIG_SYS_SCSI_SPIN_UP_TIME 2 - -/************************************************************ - * Disk-On-Chip configuration - ************************************************************/ -#define CONFIG_SYS_MAX_DOC_DEVICE 1 /* Max number of DOC devices */ -#define CONFIG_SYS_DOC_SHORT_TIMEOUT -#define CONFIG_SYS_DOC_SUPPORT_2000 -#define CONFIG_SYS_DOC_SUPPORT_MILLENNIUM - -/************************************************************ - * DISK Partition support - ************************************************************/ - -/************************************************************ - * Video support - ************************************************************/ -#define CONFIG_VIDEO_LOGO -#define CONFIG_VIDEO_ONBOARD /* Video controller is on-board */ - -/************************************************************ - * USB support - ************************************************************/ -#define CONFIG_USB_UHCI - -/* Enable needed helper functions */ - -/************************************************************ - * Debug support - ************************************************************/ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#endif - -/************************************************************ - * support BZIP2 compression - ************************************************************/ -#define CONFIG_BZIP2 1 - -#endif /* __CONFIG_H */ |