diff options
Diffstat (limited to 'include/configs/CATcenter.h')
-rw-r--r-- | include/configs/CATcenter.h | 168 |
1 files changed, 117 insertions, 51 deletions
diff --git a/include/configs/CATcenter.h b/include/configs/CATcenter.h index 4f81cde9259..15420474df0 100644 --- a/include/configs/CATcenter.h +++ b/include/configs/CATcenter.h @@ -1,4 +1,6 @@ /* + * ueberarbeitet durch Christoph Seyfert + * * (C) Copyright 2004 DENX Software Engineering, * Wolfgang Grandegger <wg@denx.de> * (C) Copyright 2003 @@ -40,6 +42,20 @@ #define CONFIG_PPCHAMELEON_MODULE_MODEL CONFIG_PPCHAMELEON_MODULE_BA #endif +/* Only one of the following two symbols must be defined (default is 25 MHz) + * CONFIG_PPCHAMELEON_CLK_25 + * CONFIG_PPCHAMELEON_CLK_33 + */ +#if (!defined(CONFIG_PPCHAMELEON_CLK_25) && !defined(CONFIG_PPCHAMELEON_CLK_33)) +#define CONFIG_PPCHAMELEON_CLK_25 +#endif + +#if (defined(CONFIG_PPCHAMELEON_CLK_25) && defined(CONFIG_PPCHAMELEON_CLK_33)) +#error "* Two external frequencies (SysClk) are defined! *" +#endif + +#undef CONFIG_PPCHAMELEON_SMI712 + /* * Debug stuff */ @@ -62,42 +78,52 @@ #define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */ #define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ +#ifdef CONFIG_PPCHAMELEON_CLK_25 +# define CONFIG_SYS_CLK_FREQ 25000000 /* external frequency to pll */ +#elif (defined (CONFIG_PPCHAMELEON_CLK_33)) #define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ +#else +# error "* External frequency (SysClk) not defined! *" +#endif -#define CONFIG_UART1_CONSOLE 1 /* Use second UART */ +#define CONFIG_UART1_CONSOLE 1 /* Use second UART */ #define CONFIG_BAUDRATE 115200 #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#define CONFIG_VERSION_VARIABLE 1 /* add version variable */ +#define CONFIG_IDENT_STRING "1" + #undef CONFIG_BOOTARGS /* Ethernet stuff */ #define CONFIG_ENV_OVERWRITE /* Let the user to change the Ethernet MAC addresses */ -#define CONFIG_ETHADDR 00:50:C2:1E:AF:FC -#define CONFIG_ETH1ADDR 00:50:C2:1E:AF:FB +#define CONFIG_ETHADDR 00:50:C2:1E:AF:FE +#define CONFIG_ETH1ADDR 00:50:C2:1E:AF:FD #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #undef CONFIG_EXT_PHY +#define CONFIG_NET_MULTI 1 #define CONFIG_MII 1 /* MII PHY management */ #ifndef CONFIG_EXT_PHY -#define CONFIG_PHY_ADDR 1 /* PHY address */ +#define CONFIG_PHY_ADDR 0 /* EMAC0 PHY address */ +#define CONFIG_PHY1_ADDR 1 /* EMAC1 PHY address */ #else #define CONFIG_PHY_ADDR 2 /* PHY address */ #endif #define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ #define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \ - CFG_CMD_DATE | \ CFG_CMD_ELF | \ CFG_CMD_EEPROM | \ CFG_CMD_I2C | \ CFG_CMD_IRQ | \ + CFG_CMD_JFFS2 | \ CFG_CMD_MII | \ - CFG_CMD_NAND | \ - CFG_CMD_JFFS2) + CFG_CMD_NAND ) #define CONFIG_MAC_PARTITION #define CONFIG_DOS_PARTITION @@ -118,7 +144,7 @@ #define CFG_LONGHELP /* undef to save memory */ #define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#undef CFG_HUSH_PARSER /* use "hush" command parser */ +#define CFG_HUSH_PARSER /* use "hush" command parser */ #ifdef CFG_HUSH_PARSER #define CFG_PROMPT_HUSH_PS2 "> " #endif @@ -294,9 +320,10 @@ #define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */ -#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */ -#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */ +#define CFG_PCI_SUBSYS_VENDORID 0x1014 /* PCI Vendor ID: IBM */ +#define CFG_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: --- */ #define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/ + #define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */ #define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */ #define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ @@ -417,23 +444,21 @@ #define CFG_EBC_PB3AP 0x92015480 #define CFG_EBC_PB3CR 0xFF058000 /* BAS=0xFF0,BS=4MB,BU=R/W,BW=8bit */ - -#if 0 /* Roese */ -/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization */ -#define CFG_EBC_PB1AP 0x92015480 -#define CFG_EBC_PB1CR 0xFF858000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=8bit */ - -/* Memory Bank 2 (CAN0, 1) initialization */ -#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ -#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */ - -/* Memory Bank 3 (CompactFlash IDE) initialization */ -#define CFG_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ -#define CFG_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */ - -/* Memory Bank 4 (NVRAM/RTC) initialization */ -#define CFG_EBC_PB4AP 0x01005280 /* TWT=2,WBN=1,WBF=1,TH=1,SOR=1 */ -#define CFG_EBC_PB4CR 0xF0218000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit */ +#ifdef CONFIG_PPCHAMELEON_SMI712 +/* + * Video console (graphic: SMI LynxEM) + */ +#define CONFIG_VIDEO +#define CONFIG_CFB_CONSOLE +#define CONFIG_VIDEO_SMI_LYNXEM +#define CONFIG_VIDEO_LOGO +/*#define CONFIG_VIDEO_BMP_LOGO*/ +#define CONFIG_CONSOLE_EXTRA_INFO +#define CONFIG_VGA_AS_SINGLE_DEVICE +/* This is the base address (on 405EP-side) used to generate I/O accesses on PCI bus */ +#define CFG_ISA_IO 0xE8000000 +/* see also drivers/videomodes.c */ +#define CFG_DEFAULT_VIDEO_MODE 0x303 #endif /*----------------------------------------------------------------------- @@ -480,7 +505,7 @@ * Definitions for initial stack pointer and data area (in data cache) */ /* use on chip memory ( OCM ) for temperary stack until sdram is tested */ -#define CFG_TEMP_STACK_OCM 1 +#define CFG_TEMP_STACK_OCM 1 /* On Chip Memory location */ #define CFG_OCM_DATA_ADDR 0xF8000000 @@ -540,7 +565,6 @@ #define DIMM_READ_ADDR 0xAB #define DIMM_WRITE_ADDR 0xAA - #define CPC0_PLLMR0 (CNTRL_DCR_BASE+0x0) /* PLL mode 0 register */ #define CPC0_BOOT (CNTRL_DCR_BASE+0x1) /* Chip Clock Status register */ #define CPC0_CR1 (CNTRL_DCR_BASE+0x2) /* Chip Control 1 register */ @@ -652,44 +676,86 @@ #define PLL_PCIDIV_3 0x00000002 #define PLL_PCIDIV_4 0x00000003 +#ifdef CONFIG_PPCHAMELEON_CLK_25 +/* CPU - PLB/SDRAM - EBC - OPB - PCI (assuming a 25.0 MHz input clock to the 405EP) */ +#define PPCHAMELEON_PLLMR0_133_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_1 | \ + PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \ + PLL_MALDIV_1 | PLL_PCIDIV_4) +#define PPCHAMELEON_PLLMR1_133_133_33_66_33 (PLL_FBKDIV_8 | \ + PLL_FWDDIVA_6 | PLL_FWDDIVB_4 | \ + PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) + +#define PPCHAMELEON_PLLMR0_200_100_50_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ + PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ + PLL_MALDIV_1 | PLL_PCIDIV_4) +#define PPCHAMELEON_PLLMR1_200_100_50_33 (PLL_FBKDIV_8 | \ + PLL_FWDDIVA_4 | PLL_FWDDIVB_4 | \ + PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) + +#define PPCHAMELEON_PLLMR0_266_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ + PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \ + PLL_MALDIV_1 | PLL_PCIDIV_4) +#define PPCHAMELEON_PLLMR1_266_133_33_66_33 (PLL_FBKDIV_8 | \ + PLL_FWDDIVA_3 | PLL_FWDDIVB_4 | \ + PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) + +#define PPCHAMELEON_PLLMR0_333_111_37_55_55 (PLL_CPUDIV_1 | PLL_PLBDIV_3 | \ + PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ + PLL_MALDIV_1 | PLL_PCIDIV_2) +#define PPCHAMELEON_PLLMR1_333_111_37_55_55 (PLL_FBKDIV_10 | \ + PLL_FWDDIVA_3 | PLL_FWDDIVB_4 | \ + PLL_TUNE_15_M_40 | PLL_TUNE_VCO_HI) + +#elif (defined (CONFIG_PPCHAMELEON_CLK_33)) + /* CPU - PLB/SDRAM - EBC - OPB - PCI (assuming a 33.3MHz input clock to the 405EP) */ -#define PLLMR0_133_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_1 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \ +#define PPCHAMELEON_PLLMR0_133_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_1 | \ + PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \ PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PLLMR1_133_133_33_66_33 (PLL_FBKDIV_4 | \ - PLL_FWDDIVA_6 | PLL_FWDDIVB_6 | \ +#define PPCHAMELEON_PLLMR1_133_133_33_66_33 (PLL_FBKDIV_4 | \ + PLL_FWDDIVA_6 | PLL_FWDDIVB_6 | \ PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) -#define PLLMR0_200_100_50_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ + +#define PPCHAMELEON_PLLMR0_200_100_50_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ + PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PLLMR1_200_100_50_33 (PLL_FBKDIV_6 | \ - PLL_FWDDIVA_4 | PLL_FWDDIVB_4 | \ +#define PPCHAMELEON_PLLMR1_200_100_50_33 (PLL_FBKDIV_6 | \ + PLL_FWDDIVA_4 | PLL_FWDDIVB_4 | \ PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) -#define PLLMR0_266_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \ + +#define PPCHAMELEON_PLLMR0_266_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ + PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \ PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PLLMR1_266_133_33_66_33 (PLL_FBKDIV_8 | \ - PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \ +#define PPCHAMELEON_PLLMR1_266_133_33_66_33 (PLL_FBKDIV_8 | \ + PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \ PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) -#define PLLMR0_333_111_37_55_55 (PLL_CPUDIV_1 | PLL_PLBDIV_3 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ + +#define PPCHAMELEON_PLLMR0_333_111_37_55_55 (PLL_CPUDIV_1 | PLL_PLBDIV_3 | \ + PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ PLL_MALDIV_1 | PLL_PCIDIV_2) -#define PLLMR1_333_111_37_55_55 (PLL_FBKDIV_10 | \ - PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \ +#define PPCHAMELEON_PLLMR1_333_111_37_55_55 (PLL_FBKDIV_10 | \ + PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \ PLL_TUNE_15_M_40 | PLL_TUNE_VCO_HI) +#else +#error "* External frequency (SysClk) not defined! *" +#endif + #if (CONFIG_PPCHAMELEON_MODULE_MODEL == CONFIG_PPCHAMELEON_MODULE_HI) /* Model HI */ -#define PLLMR0_DEFAULT PLLMR0_333_111_37_55_55 -#define PLLMR1_DEFAULT PLLMR1_333_111_37_55_55 +#define PLLMR0_DEFAULT PPCHAMELEON_PLLMR0_333_111_37_55_55 +#define PLLMR1_DEFAULT PPCHAMELEON_PLLMR1_333_111_37_55_55 +#define CFG_OPB_FREQ 55555555 /* Model ME */ #elif (CONFIG_PPCHAMELEON_MODULE_MODEL == CONFIG_PPCHAMELEON_MODULE_ME) -#define PLLMR0_DEFAULT PLLMR0_266_133_33_66_33 -#define PLLMR1_DEFAULT PLLMR1_266_133_33_66_33 +#define PLLMR0_DEFAULT PPCHAMELEON_PLLMR0_266_133_33_66_33 +#define PLLMR1_DEFAULT PPCHAMELEON_PLLMR1_266_133_33_66_33 +#define CFG_OPB_FREQ 66666666 #else /* Model BA (default) */ -#define PLLMR0_DEFAULT PLLMR0_133_133_33_66_33 -#define PLLMR1_DEFAULT PLLMR1_133_133_33_66_33 +#define PLLMR0_DEFAULT PPCHAMELEON_PLLMR0_133_133_33_66_33 +#define PLLMR1_DEFAULT PPCHAMELEON_PLLMR1_133_133_33_66_33 +#define CFG_OPB_FREQ 66666666 #endif #endif /* CONFIG_NO_SERIAL_EEPROM */ |