diff options
Diffstat (limited to 'drivers/mtd/nand/raw/fsl_elbc_nand.c')
| -rw-r--r-- | drivers/mtd/nand/raw/fsl_elbc_nand.c | 810 |
1 files changed, 810 insertions, 0 deletions
diff --git a/drivers/mtd/nand/raw/fsl_elbc_nand.c b/drivers/mtd/nand/raw/fsl_elbc_nand.c new file mode 100644 index 0000000000..263d46ec8f --- /dev/null +++ b/drivers/mtd/nand/raw/fsl_elbc_nand.c @@ -0,0 +1,810 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* Freescale Enhanced Local Bus Controller FCM NAND driver + * + * Copyright (c) 2006-2008 Freescale Semiconductor + * + * Authors: Nick Spence <nick.spence@freescale.com>, + * Scott Wood <scottwood@freescale.com> + */ + +#include <common.h> +#include <malloc.h> +#include <nand.h> + +#include <linux/mtd/mtd.h> +#include <linux/mtd/rawnand.h> +#include <linux/mtd/nand_ecc.h> + +#include <asm/io.h> +#include <linux/errno.h> + +#ifdef VERBOSE_DEBUG +#define DEBUG_ELBC +#define vdbg(format, arg...) printf("DEBUG: " format, ##arg) +#else +#define vdbg(format, arg...) do {} while (0) +#endif + +/* Can't use plain old DEBUG because the linux mtd + * headers define it as a macro. + */ +#ifdef DEBUG_ELBC +#define dbg(format, arg...) printf("DEBUG: " format, ##arg) +#else +#define dbg(format, arg...) do {} while (0) +#endif + +#define MAX_BANKS 8 +#define ERR_BYTE 0xFF /* Value returned for read bytes when read failed */ + +#define LTESR_NAND_MASK (LTESR_FCT | LTESR_PAR | LTESR_CC) + +struct fsl_elbc_ctrl; + +/* mtd information per set */ + +struct fsl_elbc_mtd { + struct nand_chip chip; + struct fsl_elbc_ctrl *ctrl; + + struct device *dev; + int bank; /* Chip select bank number */ + u8 __iomem *vbase; /* Chip select base virtual address */ + int page_size; /* NAND page size (0=512, 1=2048) */ + unsigned int fmr; /* FCM Flash Mode Register value */ +}; + +/* overview of the fsl elbc controller */ + +struct fsl_elbc_ctrl { + struct nand_hw_control controller; + struct fsl_elbc_mtd *chips[MAX_BANKS]; + + /* device info */ + fsl_lbc_t *regs; + u8 __iomem *addr; /* Address of assigned FCM buffer */ + unsigned int page; /* Last page written to / read from */ + unsigned int read_bytes; /* Number of bytes read during command */ + unsigned int column; /* Saved column from SEQIN */ + unsigned int index; /* Pointer to next byte to 'read' */ + unsigned int status; /* status read from LTESR after last op */ + unsigned int mdr; /* UPM/FCM Data Register value */ + unsigned int use_mdr; /* Non zero if the MDR is to be set */ + unsigned int oob; /* Non zero if operating on OOB data */ +}; + +/* These map to the positions used by the FCM hardware ECC generator */ + +/* Small Page FLASH with FMR[ECCM] = 0 */ +static struct nand_ecclayout fsl_elbc_oob_sp_eccm0 = { + .eccbytes = 3, + .eccpos = {6, 7, 8}, + .oobfree = { {0, 5}, {9, 7} }, +}; + +/* Small Page FLASH with FMR[ECCM] = 1 */ +static struct nand_ecclayout fsl_elbc_oob_sp_eccm1 = { + .eccbytes = 3, + .eccpos = {8, 9, 10}, + .oobfree = { {0, 5}, {6, 2}, {11, 5} }, +}; + +/* Large Page FLASH with FMR[ECCM] = 0 */ +static struct nand_ecclayout fsl_elbc_oob_lp_eccm0 = { + .eccbytes = 12, + .eccpos = {6, 7, 8, 22, 23, 24, 38, 39, 40, 54, 55, 56}, + .oobfree = { {1, 5}, {9, 13}, {25, 13}, {41, 13}, {57, 7} }, +}; + +/* Large Page FLASH with FMR[ECCM] = 1 */ +static struct nand_ecclayout fsl_elbc_oob_lp_eccm1 = { + .eccbytes = 12, + .eccpos = {8, 9, 10, 24, 25, 26, 40, 41, 42, 56, 57, 58}, + .oobfree = { {1, 7}, {11, 13}, {27, 13}, {43, 13}, {59, 5} }, +}; + +/* + * fsl_elbc_oob_lp_eccm* specify that LP NAND's OOB free area starts at offset + * 1, so we have to adjust bad block pattern. This pattern should be used for + * x8 chips only. So far hardware does not support x16 chips anyway. + */ +static u8 scan_ff_pattern[] = { 0xff, }; + +static struct nand_bbt_descr largepage_memorybased = { + .options = 0, + .offs = 0, + .len = 1, + .pattern = scan_ff_pattern, +}; + +/* + * ELBC may use HW ECC, so that OOB offsets, that NAND core uses for bbt, + * interfere with ECC positions, that's why we implement our own descriptors. + * OOB {11, 5}, works for both SP and LP chips, with ECCM = 1 and ECCM = 0. + */ +static u8 bbt_pattern[] = {'B', 'b', 't', '0' }; +static u8 mirror_pattern[] = {'1', 't', 'b', 'B' }; + +static struct nand_bbt_descr bbt_main_descr = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE | + NAND_BBT_2BIT | NAND_BBT_VERSION, + .offs = 11, + .len = 4, + .veroffs = 15, + .maxblocks = 4, + .pattern = bbt_pattern, +}; + +static struct nand_bbt_descr bbt_mirror_descr = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE | + NAND_BBT_2BIT | NAND_BBT_VERSION, + .offs = 11, + .len = 4, + .veroffs = 15, + .maxblocks = 4, + .pattern = mirror_pattern, +}; + +/*=================================*/ + +/* + * Set up the FCM hardware block and page address fields, and the fcm + * structure addr field to point to the correct FCM buffer in memory + */ +static void set_addr(struct mtd_info *mtd, int column, int page_addr, int oob) +{ + struct nand_chip *chip = mtd_to_nand(mtd); + struct fsl_elbc_mtd *priv = nand_get_controller_data(chip); + struct fsl_elbc_ctrl *ctrl = priv->ctrl; + fsl_lbc_t *lbc = ctrl->regs; + int buf_num; + + ctrl->page = page_addr; + + if (priv->page_size) { + out_be32(&lbc->fbar, page_addr >> 6); + out_be32(&lbc->fpar, + ((page_addr << FPAR_LP_PI_SHIFT) & FPAR_LP_PI) | + (oob ? FPAR_LP_MS : 0) | column); + buf_num = (page_addr & 1) << 2; + } else { + out_be32(&lbc->fbar, page_addr >> 5); + out_be32(&lbc->fpar, + ((page_addr << FPAR_SP_PI_SHIFT) & FPAR_SP_PI) | + (oob ? FPAR_SP_MS : 0) | column); + buf_num = page_addr & 7; + } + + ctrl->addr = priv->vbase + buf_num * 1024; + ctrl->index = column; + + /* for OOB data point to the second half of the buffer */ + if (oob) + ctrl->index += priv->page_size ? 2048 : 512; + + vdbg("set_addr: bank=%d, ctrl->addr=0x%p (0x%p), " + "index %x, pes %d ps %d\n", + buf_num, ctrl->addr, priv->vbase, ctrl->index, + chip->phys_erase_shift, chip->page_shift); +} + +/* + * execute FCM command and wait for it to complete + */ +static int fsl_elbc_run_command(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd_to_nand(mtd); + struct fsl_elbc_mtd *priv = nand_get_controller_data(chip); + struct fsl_elbc_ctrl *ctrl = priv->ctrl; + fsl_lbc_t *lbc = ctrl->regs; + u32 timeo = (CONFIG_SYS_HZ * 10) / 1000; + u32 time_start; + u32 ltesr; + + /* Setup the FMR[OP] to execute without write protection */ + out_be32(&lbc->fmr, priv->fmr | 3); + if (ctrl->use_mdr) + out_be32(&lbc->mdr, ctrl->mdr); + + vdbg("fsl_elbc_run_command: fmr=%08x fir=%08x fcr=%08x\n", + in_be32(&lbc->fmr), in_be32(&lbc->fir), in_be32(&lbc->fcr)); + vdbg("fsl_elbc_run_command: fbar=%08x fpar=%08x " + "fbcr=%08x bank=%d\n", + in_be32(&lbc->fbar), in_be32(&lbc->fpar), + in_be32(&lbc->fbcr), priv->bank); + + /* execute special operation */ + out_be32(&lbc->lsor, priv->bank); + + /* wait for FCM complete flag or timeout */ + time_start = get_timer(0); + + ltesr = 0; + while (get_timer(time_start) < timeo) { + ltesr = in_be32(&lbc->ltesr); + if (ltesr & LTESR_CC) + break; + } + + ctrl->status = ltesr & LTESR_NAND_MASK; + out_be32(&lbc->ltesr, ctrl->status); + out_be32(&lbc->lteatr, 0); + + /* store mdr value in case it was needed */ + if (ctrl->use_mdr) + ctrl->mdr = in_be32(&lbc->mdr); + + ctrl->use_mdr = 0; + + vdbg("fsl_elbc_run_command: stat=%08x mdr=%08x fmr=%08x\n", + ctrl->status, ctrl->mdr, in_be32(&lbc->fmr)); + + /* returns 0 on success otherwise non-zero) */ + return ctrl->status == LTESR_CC ? 0 : -EIO; +} + +static void fsl_elbc_do_read(struct nand_chip *chip, int oob) +{ + struct fsl_elbc_mtd *priv = nand_get_controller_data(chip); + struct fsl_elbc_ctrl *ctrl = priv->ctrl; + fsl_lbc_t *lbc = ctrl->regs; + + if (priv->page_size) { + out_be32(&lbc->fir, + (FIR_OP_CW0 << FIR_OP0_SHIFT) | + (FIR_OP_CA << FIR_OP1_SHIFT) | + (FIR_OP_PA << FIR_OP2_SHIFT) | + (FIR_OP_CW1 << FIR_OP3_SHIFT) | + (FIR_OP_RBW << FIR_OP4_SHIFT)); + + out_be32(&lbc->fcr, (NAND_CMD_READ0 << FCR_CMD0_SHIFT) | + (NAND_CMD_READSTART << FCR_CMD1_SHIFT)); + } else { + out_be32(&lbc->fir, + (FIR_OP_CW0 << FIR_OP0_SHIFT) | + (FIR_OP_CA << FIR_OP1_SHIFT) | + (FIR_OP_PA << FIR_OP2_SHIFT) | + (FIR_OP_RBW << FIR_OP3_SHIFT)); + + if (oob) + out_be32(&lbc->fcr, + NAND_CMD_READOOB << FCR_CMD0_SHIFT); + else + out_be32(&lbc->fcr, NAND_CMD_READ0 << FCR_CMD0_SHIFT); + } +} + +/* cmdfunc send commands to the FCM */ +static void fsl_elbc_cmdfunc(struct mtd_info *mtd, unsigned int command, + int column, int page_addr) +{ + struct nand_chip *chip = mtd_to_nand(mtd); + struct fsl_elbc_mtd *priv = nand_get_controller_data(chip); + struct fsl_elbc_ctrl *ctrl = priv->ctrl; + fsl_lbc_t *lbc = ctrl->regs; + + ctrl->use_mdr = 0; + + /* clear the read buffer */ + ctrl->read_bytes = 0; + if (command != NAND_CMD_PAGEPROG) + ctrl->index = 0; + + switch (command) { + /* READ0 and READ1 read the entire buffer to use hardware ECC. */ + case NAND_CMD_READ1: + column += 256; + + /* fall-through */ + case NAND_CMD_READ0: + vdbg("fsl_elbc_cmdfunc: NAND_CMD_READ0, page_addr:" + " 0x%x, column: 0x%x.\n", page_addr, column); + + out_be32(&lbc->fbcr, 0); /* read entire page to enable ECC */ + set_addr(mtd, 0, page_addr, 0); + + ctrl->read_bytes = mtd->writesize + mtd->oobsize; + ctrl->index += column; + + fsl_elbc_do_read(chip, 0); + fsl_elbc_run_command(mtd); + return; + + /* READOOB reads only the OOB because no ECC is performed. */ + case NAND_CMD_READOOB: + vdbg("fsl_elbc_cmdfunc: NAND_CMD_READOOB, page_addr:" + " 0x%x, column: 0x%x.\n", page_addr, column); + + out_be32(&lbc->fbcr, mtd->oobsize - column); + set_addr(mtd, column, page_addr, 1); + + ctrl->read_bytes = mtd->writesize + mtd->oobsize; + + fsl_elbc_do_read(chip, 1); + fsl_elbc_run_command(mtd); + + return; + + /* READID must read all 5 possible bytes while CEB is active */ + case NAND_CMD_READID: + case NAND_CMD_PARAM: + vdbg("fsl_elbc_cmdfunc: NAND_CMD 0x%x.\n", command); + + out_be32(&lbc->fir, (FIR_OP_CW0 << FIR_OP0_SHIFT) | + (FIR_OP_UA << FIR_OP1_SHIFT) | + (FIR_OP_RBW << FIR_OP2_SHIFT)); + out_be32(&lbc->fcr, command << FCR_CMD0_SHIFT); + /* + * although currently it's 8 bytes for READID, we always read + * the maximum 256 bytes(for PARAM) + */ + out_be32(&lbc->fbcr, 256); + ctrl->read_bytes = 256; + ctrl->use_mdr = 1; + ctrl->mdr = column; + set_addr(mtd, 0, 0, 0); + fsl_elbc_run_command(mtd); + return; + + /* ERASE1 stores the block and page address */ + case NAND_CMD_ERASE1: + vdbg("fsl_elbc_cmdfunc: NAND_CMD_ERASE1, " + "page_addr: 0x%x.\n", page_addr); + set_addr(mtd, 0, page_addr, 0); + return; + + /* ERASE2 uses the block and page address from ERASE1 */ + case NAND_CMD_ERASE2: + vdbg("fsl_elbc_cmdfunc: NAND_CMD_ERASE2.\n"); + + out_be32(&lbc->fir, + (FIR_OP_CW0 << FIR_OP0_SHIFT) | + (FIR_OP_PA << FIR_OP1_SHIFT) | + (FIR_OP_CM1 << FIR_OP2_SHIFT)); + + out_be32(&lbc->fcr, + (NAND_CMD_ERASE1 << FCR_CMD0_SHIFT) | + (NAND_CMD_ERASE2 << FCR_CMD1_SHIFT)); + + out_be32(&lbc->fbcr, 0); + ctrl->read_bytes = 0; + + fsl_elbc_run_command(mtd); + return; + + /* SEQIN sets up the addr buffer and all registers except the length */ + case NAND_CMD_SEQIN: { + u32 fcr; + vdbg("fsl_elbc_cmdfunc: NAND_CMD_SEQIN/PAGE_PROG, " + "page_addr: 0x%x, column: 0x%x.\n", + page_addr, column); + + ctrl->column = column; + ctrl->oob = 0; + + if (priv->page_size) { + fcr = (NAND_CMD_SEQIN << FCR_CMD0_SHIFT) | + (NAND_CMD_PAGEPROG << FCR_CMD1_SHIFT); + + out_be32(&lbc->fir, + (FIR_OP_CW0 << FIR_OP0_SHIFT) | + (FIR_OP_CA << FIR_OP1_SHIFT) | + (FIR_OP_PA << FIR_OP2_SHIFT) | + (FIR_OP_WB << FIR_OP3_SHIFT) | + (FIR_OP_CW1 << FIR_OP4_SHIFT)); + } else { + fcr = (NAND_CMD_PAGEPROG << FCR_CMD1_SHIFT) | + (NAND_CMD_SEQIN << FCR_CMD2_SHIFT); + + out_be32(&lbc->fir, + (FIR_OP_CW0 << FIR_OP0_SHIFT) | + (FIR_OP_CM2 << FIR_OP1_SHIFT) | + (FIR_OP_CA << FIR_OP2_SHIFT) | + (FIR_OP_PA << FIR_OP3_SHIFT) | + (FIR_OP_WB << FIR_OP4_SHIFT) | + (FIR_OP_CW1 << FIR_OP5_SHIFT)); + + if (column >= mtd->writesize) { + /* OOB area --> READOOB */ + column -= mtd->writesize; + fcr |= NAND_CMD_READOOB << FCR_CMD0_SHIFT; + ctrl->oob = 1; + } else if (column < 256) { + /* First 256 bytes --> READ0 */ + fcr |= NAND_CMD_READ0 << FCR_CMD0_SHIFT; + } else { + /* Second 256 bytes --> READ1 */ + fcr |= NAND_CMD_READ1 << FCR_CMD0_SHIFT; + } + } + + out_be32(&lbc->fcr, fcr); + set_addr(mtd, column, page_addr, ctrl->oob); + return; + } + + /* PAGEPROG reuses all of the setup from SEQIN and adds the length */ + case NAND_CMD_PAGEPROG: { + vdbg("fsl_elbc_cmdfunc: NAND_CMD_PAGEPROG " + "writing %d bytes.\n", ctrl->index); + + /* if the write did not start at 0 or is not a full page + * then set the exact length, otherwise use a full page + * write so the HW generates the ECC. + */ + if (ctrl->oob || ctrl->column != 0 || + ctrl->index != mtd->writesize + mtd->oobsize) + out_be32(&lbc->fbcr, ctrl->index); + else + out_be32(&lbc->fbcr, 0); + + fsl_elbc_run_command(mtd); + + return; + } + + /* CMD_STATUS must read the status byte while CEB is active */ + /* Note - it does not wait for the ready line */ + case NAND_CMD_STATUS: + out_be32(&lbc->fir, + (FIR_OP_CM0 << FIR_OP0_SHIFT) | + (FIR_OP_RBW << FIR_OP1_SHIFT)); + out_be32(&lbc->fcr, NAND_CMD_STATUS << FCR_CMD0_SHIFT); + out_be32(&lbc->fbcr, 1); + set_addr(mtd, 0, 0, 0); + ctrl->read_bytes = 1; + + fsl_elbc_run_command(mtd); + + /* The chip always seems to report that it is + * write-protected, even when it is not. + */ + out_8(ctrl->addr, in_8(ctrl->addr) | NAND_STATUS_WP); + return; + + /* RESET without waiting for the ready line */ + case NAND_CMD_RESET: + dbg("fsl_elbc_cmdfunc: NAND_CMD_RESET.\n"); + out_be32(&lbc->fir, FIR_OP_CM0 << FIR_OP0_SHIFT); + out_be32(&lbc->fcr, NAND_CMD_RESET << FCR_CMD0_SHIFT); + fsl_elbc_run_command(mtd); + return; + + default: + printf("fsl_elbc_cmdfunc: error, unsupported command 0x%x.\n", + command); + } +} + +static void fsl_elbc_select_chip(struct mtd_info *mtd, int chip) +{ + /* The hardware does not seem to support multiple + * chips per bank. + */ +} + +/* + * Write buf to the FCM Controller Data Buffer + */ +static void fsl_elbc_write_buf(struct mtd_info *mtd, const u8 *buf, int len) +{ + struct nand_chip *chip = mtd_to_nand(mtd); + struct fsl_elbc_mtd *priv = nand_get_controller_data(chip); + struct fsl_elbc_ctrl *ctrl = priv->ctrl; + unsigned int bufsize = mtd->writesize + mtd->oobsize; + + if (len <= 0) { + printf("write_buf of %d bytes", len); + ctrl->status = 0; + return; + } + + if ((unsigned int)len > bufsize - ctrl->index) { + printf("write_buf beyond end of buffer " + "(%d requested, %u available)\n", + len, bufsize - ctrl->index); + len = bufsize - ctrl->index; + } + + memcpy_toio(&ctrl->addr[ctrl->index], buf, len); + /* + * This is workaround for the weird elbc hangs during nand write, + * Scott Wood says: "...perhaps difference in how long it takes a + * write to make it through the localbus compared to a write to IMMR + * is causing problems, and sync isn't helping for some reason." + * Reading back the last byte helps though. + */ + in_8(&ctrl->addr[ctrl->index] + len - 1); + + ctrl->index += len; +} + +/* + * read a byte from either the FCM hardware buffer if it has any data left + * otherwise issue a command to read a single byte. + */ +static u8 fsl_elbc_read_byte(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd_to_nand(mtd); + struct fsl_elbc_mtd *priv = nand_get_controller_data(chip); + struct fsl_elbc_ctrl *ctrl = priv->ctrl; + + /* If there are still bytes in the FCM, then use the next byte. */ + if (ctrl->index < ctrl->read_bytes) + return in_8(&ctrl->addr[ctrl->index++]); + + printf("read_byte beyond end of buffer\n"); + return ERR_BYTE; +} + +/* + * Read from the FCM Controller Data Buffer + */ +static void fsl_elbc_read_buf(struct mtd_info *mtd, u8 *buf, int len) +{ + struct nand_chip *chip = mtd_to_nand(mtd); + struct fsl_elbc_mtd *priv = nand_get_controller_data(chip); + struct fsl_elbc_ctrl *ctrl = priv->ctrl; + int avail; + + if (len < 0) + return; + + avail = min((unsigned int)len, ctrl->read_bytes - ctrl->index); + memcpy_fromio(buf, &ctrl->addr[ctrl->index], avail); + ctrl->index += avail; + + if (len > avail) + printf("read_buf beyond end of buffer " + "(%d requested, %d available)\n", + len, avail); +} + +/* This function is called after Program and Erase Operations to + * check for success or failure. + */ +static int fsl_elbc_wait(struct mtd_info *mtd, struct nand_chip *chip) +{ + struct fsl_elbc_mtd *priv = nand_get_controller_data(chip); + struct fsl_elbc_ctrl *ctrl = priv->ctrl; + fsl_lbc_t *lbc = ctrl->regs; + + if (ctrl->status != LTESR_CC) + return NAND_STATUS_FAIL; + + /* Use READ_STATUS command, but wait for the device to be ready */ + ctrl->use_mdr = 0; + out_be32(&lbc->fir, + (FIR_OP_CW0 << FIR_OP0_SHIFT) | + (FIR_OP_RBW << FIR_OP1_SHIFT)); + out_be32(&lbc->fcr, NAND_CMD_STATUS << FCR_CMD0_SHIFT); + out_be32(&lbc->fbcr, 1); + set_addr(mtd, 0, 0, 0); + ctrl->read_bytes = 1; + + fsl_elbc_run_command(mtd); + + if (ctrl->status != LTESR_CC) + return NAND_STATUS_FAIL; + + /* The chip always seems to report that it is + * write-protected, even when it is not. + */ + out_8(ctrl->addr, in_8(ctrl->addr) | NAND_STATUS_WP); + return fsl_elbc_read_byte(mtd); +} + +static int fsl_elbc_read_page(struct mtd_info *mtd, struct nand_chip *chip, + uint8_t *buf, int oob_required, int page) +{ + fsl_elbc_read_buf(mtd, buf, mtd->writesize); + fsl_elbc_read_buf(mtd, chip->oob_poi, mtd->oobsize); + + if (fsl_elbc_wait(mtd, chip) & NAND_STATUS_FAIL) + mtd->ecc_stats.failed++; + + return 0; +} + +/* ECC will be calculated automatically, and errors will be detected in + * waitfunc. + */ +static int fsl_elbc_write_page(struct mtd_info *mtd, struct nand_chip *chip, + const uint8_t *buf, int oob_required, + int page) +{ + fsl_elbc_write_buf(mtd, buf, mtd->writesize); + fsl_elbc_write_buf(mtd, chip->oob_poi, mtd->oobsize); + + return 0; +} + +static struct fsl_elbc_ctrl *elbc_ctrl; + +/* ECC will be calculated automatically, and errors will be detected in + * waitfunc. + */ +static int fsl_elbc_write_subpage(struct mtd_info *mtd, struct nand_chip *chip, + uint32_t offset, uint32_t data_len, + const uint8_t *buf, int oob_required, int page) +{ + fsl_elbc_write_buf(mtd, buf, mtd->writesize); + fsl_elbc_write_buf(mtd, chip->oob_poi, mtd->oobsize); + + return 0; +} + +static void fsl_elbc_ctrl_init(void) +{ + elbc_ctrl = kzalloc(sizeof(*elbc_ctrl), GFP_KERNEL); + if (!elbc_ctrl) + return; + + elbc_ctrl->regs = LBC_BASE_ADDR; + + /* clear event registers */ + out_be32(&elbc_ctrl->regs->ltesr, LTESR_NAND_MASK); + out_be32(&elbc_ctrl->regs->lteatr, 0); + + /* Enable interrupts for any detected events */ + out_be32(&elbc_ctrl->regs->lteir, LTESR_NAND_MASK); + + elbc_ctrl->read_bytes = 0; + elbc_ctrl->index = 0; + elbc_ctrl->addr = NULL; +} + +static int fsl_elbc_chip_init(int devnum, u8 *addr) +{ + struct mtd_info *mtd; + struct nand_chip *nand; + struct fsl_elbc_mtd *priv; + uint32_t br = 0, or = 0; + int ret; + + if (!elbc_ctrl) { + fsl_elbc_ctrl_init(); + if (!elbc_ctrl) + return -1; + } + + priv = kzalloc(sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + priv->ctrl = elbc_ctrl; + priv->vbase = addr; + + /* Find which chip select it is connected to. It'd be nice + * if we could pass more than one datum to the NAND driver... + */ + for (priv->bank = 0; priv->bank < MAX_BANKS; priv->bank++) { + phys_addr_t phys_addr = virt_to_phys(addr); + + br = in_be32(&elbc_ctrl->regs->bank[priv->bank].br); + or = in_be32(&elbc_ctrl->regs->bank[priv->bank].or); + + if ((br & BR_V) && (br & BR_MSEL) == BR_MS_FCM && + (br & or & BR_BA) == BR_PHYS_ADDR(phys_addr)) + break; + } + + if (priv->bank >= MAX_BANKS) { + printf("fsl_elbc_nand: address did not match any " + "chip selects\n"); + kfree(priv); + return -ENODEV; + } + + nand = &priv->chip; + mtd = nand_to_mtd(nand); + + elbc_ctrl->chips[priv->bank] = priv; + + /* fill in nand_chip structure */ + /* set up function call table */ + nand->read_byte = fsl_elbc_read_byte; + nand->write_buf = fsl_elbc_write_buf; + nand->read_buf = fsl_elbc_read_buf; + nand->select_chip = fsl_elbc_select_chip; + nand->cmdfunc = fsl_elbc_cmdfunc; + nand->waitfunc = fsl_elbc_wait; + + /* set up nand options */ + nand->bbt_td = &bbt_main_descr; + nand->bbt_md = &bbt_mirror_descr; + + /* set up nand options */ + nand->options = NAND_NO_SUBPAGE_WRITE; + nand->bbt_options = NAND_BBT_USE_FLASH; + + nand->controller = &elbc_ctrl->controller; + nand_set_controller_data(nand, priv); + + nand->ecc.read_page = fsl_elbc_read_page; + nand->ecc.write_page = fsl_elbc_write_page; + nand->ecc.write_subpage = fsl_elbc_write_subpage; + + priv->fmr = (15 << FMR_CWTO_SHIFT) | (2 << FMR_AL_SHIFT); + + /* If CS Base Register selects full hardware ECC then use it */ + if ((br & BR_DECC) == BR_DECC_CHK_GEN) { + nand->ecc.mode = NAND_ECC_HW; + + nand->ecc.layout = (priv->fmr & FMR_ECCM) ? + &fsl_elbc_oob_sp_eccm1 : + &fsl_elbc_oob_sp_eccm0; + + nand->ecc.size = 512; + nand->ecc.bytes = 3; + nand->ecc.steps = 1; + nand->ecc.strength = 1; + } else { + /* otherwise fall back to software ECC */ +#if defined(CONFIG_NAND_ECC_BCH) + nand->ecc.mode = NAND_ECC_SOFT_BCH; +#else + nand->ecc.mode = NAND_ECC_SOFT; +#endif + } + + ret = nand_scan_ident(mtd, 1, NULL); + if (ret) + return ret; + + /* Large-page-specific setup */ + if (mtd->writesize == 2048) { + setbits_be32(&elbc_ctrl->regs->bank[priv->bank].or, + OR_FCM_PGS); + in_be32(&elbc_ctrl->regs->bank[priv->bank].or); + + priv->page_size = 1; + nand->badblock_pattern = &largepage_memorybased; + + /* + * Hardware expects small page has ECCM0, large page has + * ECCM1 when booting from NAND, and we follow that even + * when not booting from NAND. + */ + priv->fmr |= FMR_ECCM; + + /* adjust ecc setup if needed */ + if ((br & BR_DECC) == BR_DECC_CHK_GEN) { + nand->ecc.steps = 4; + nand->ecc.layout = (priv->fmr & FMR_ECCM) ? + &fsl_elbc_oob_lp_eccm1 : + &fsl_elbc_oob_lp_eccm0; + } + } else if (mtd->writesize == 512) { + clrbits_be32(&elbc_ctrl->regs->bank[priv->bank].or, + OR_FCM_PGS); + in_be32(&elbc_ctrl->regs->bank[priv->bank].or); + } else { + return -ENODEV; + } + + ret = nand_scan_tail(mtd); + if (ret) + return ret; + + ret = nand_register(devnum, mtd); + if (ret) + return ret; + + return 0; +} + +#ifndef CONFIG_SYS_NAND_BASE_LIST +#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } +#endif + +static unsigned long base_address[CONFIG_SYS_MAX_NAND_DEVICE] = + CONFIG_SYS_NAND_BASE_LIST; + +void board_nand_init(void) +{ + int i; + + for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++) + fsl_elbc_chip_init(i, (u8 *)base_address[i]); +} |