diff options
Diffstat (limited to 'doc')
-rw-r--r-- | doc/README.kmeter1 | 91 | ||||
-rw-r--r-- | doc/README.simpc8313 | 80 |
2 files changed, 171 insertions, 0 deletions
diff --git a/doc/README.kmeter1 b/doc/README.kmeter1 new file mode 100644 index 00000000000..44ebb7a7811 --- /dev/null +++ b/doc/README.kmeter1 @@ -0,0 +1,91 @@ +Keymile kmeter1 Board +----------------------------------------- +1. Alternative Boot EEPROM + + Upon the kmeter1 startup the I2C_1 controller is used to fetch the boot + configuration from a serial EEPROM. During the development and debugging + phase it might be helpful to apply an alternative boot configuration in + a simple way. Therefore it is an alternative boot eeprom on the PIGGY, + which can be activated by setting the "ST" jumper on the PIGGY board. + +2. Memory Map + + BaseAddr PortSz Size Device + ----------- ------ ----- ------ + 0x0000_0000 64 bit 256MB DDR + 0x8000_0000 8 bit 256KB GPIO/PIGGY on CS1 + 0xa000_0000 8 bit 256MB PAXE on CS3 + 0xe000_0000 2MB Int Mem Reg Space + 0xf000_0000 16 bit 256MB FLASH on CS0 + + + DDR-SDRAM: + The current realization is made with four 16-bits memory devices. + Mounting options have been foreseen for device architectures from + 4Mx16 to 512Mx16. The kmeter1 is equipped with four 32Mx16 devices + thus resulting in a total capacity of 256MBytes. + +3. Compilation + + Assuming you're using BASH shell: + + export CROSS_COMPILE=your-cross-compile-prefix + cd u-boot + make distclean + make kmeter1_config + make + +4. Downloading and Flashing Images + +4.0 Download over serial line using Kermit: + + loadb + [Drop to kermit: + ^\c + send <u-boot-bin-image> + c + ] + + + Or via tftp: + + tftp 10000 u-boot.bin + => run load + Using FSL UEC0 device + TFTP from server 192.168.1.1; our IP address is 192.168.205.4 + Filename '/tftpboot/kmeter1/u-boot.bin'. + Load address: 0x200000 + Loading: ############## + done + Bytes transferred = 204204 (31dac hex) + => + +4.1 Reflash U-boot Image using U-boot + + => run update + ..... done + Un-Protected 5 sectors + + ..... done + Erased 5 sectors + Copy to Flash... done + ..... done + Protected 5 sectors + Total of 204204 bytes were the same + Saving Environment to Flash... + . done + Un-Protected 1 sectors + . done + Un-Protected 1 sectors + Erasing Flash... + . done + Erased 1 sectors + Writing to Flash... done + . done + Protected 1 sectors + . done + Protected 1 sectors + => + +5. Notes + 1) The console baudrate for kmeter1 is 115200bps. diff --git a/doc/README.simpc8313 b/doc/README.simpc8313 new file mode 100644 index 00000000000..b362c6aeea0 --- /dev/null +++ b/doc/README.simpc8313 @@ -0,0 +1,80 @@ +Sheldon Instruments SIMPC8313 Board +----------------------------------------- + +1. Board Switches and Jumpers + + S2 is used to set CFG_RESET_SOURCE. + + To boot the image in Large page NAND flash, use these DIP + switch settings for S2: + + +----------+ ON + | * * **** | + | * * | + +----------+ + 12345678 + + To boot the image in Small page NAND flash, use these DIP + switch settings for S2: + + +----------+ ON + | *** **** | + | * | + +----------+ + 12345678 + (where the '*' indicates the position of the tab of the switch.) + +2. Memory Map + The memory map looks like this: + + 0x0000_0000 0x1fff_ffff DDR 512M + 0x8000_0000 0x8fff_ffff PCI MEM 256M + 0x9000_0000 0x9fff_ffff PCI_MMIO 256M + 0xe000_0000 0xe00f_ffff IMMR 1M + 0xe200_0000 0xe20f_ffff PCI IO 16M + 0xe280_0000 0xe280_7fff NAND FLASH (CS0) 32K + or + 0xe280_0000 0xe281_ffff NAND FLASH (CS0) 128K + 0xff00_0000 0xff00_7fff FPGA (CS1) 1M + +3. Compilation + + Assuming you're using BASH (or similar) as your shell: + + export CROSS_COMPILE=your-cross-compiler-prefix- + make distclean + make SIMPC8313_LP_config + (or make SIMPC8313_SP_config, depending on the page size + of your NAND flash) + make + +4. Downloading and Flashing Images + +4.1 Reflash U-boot Image using U-boot + + =>run update_uboot + + You may want to try + =>tftp $loadaddr $uboot + first, to make sure that the TFTP load will succeed before it + goes ahead and wipes out your current firmware. And of course, + if the new u-boot doesn't boot, you can plug the board into + your PCI slot and with the supplied driver and sample app + you can reburn a working u-boot. + +4.2 Downloading and Booting Linux Kernel + + Ensure that all networking-related environment variables are set + properly (including ipaddr, serverip, gatewayip (if needed), + netmask, ethaddr, eth1addr, fdtfile, and bootfile). + + =>tftp $loadaddr uImage + =>nand write $loadaddr kernel $filesize + =>tftp $loadaddr $fdtfile + =>nand write $loadaddr 7e0000 1800 + + =>boot + +5 Notes + + The console baudrate for SIMPC8313 is 115200bps. |