diff options
Diffstat (limited to 'doc/README.mpc8569mds')
| -rw-r--r-- | doc/README.mpc8569mds | 77 |
1 files changed, 0 insertions, 77 deletions
diff --git a/doc/README.mpc8569mds b/doc/README.mpc8569mds deleted file mode 100644 index 3d12a964cd..0000000000 --- a/doc/README.mpc8569mds +++ /dev/null @@ -1,77 +0,0 @@ -Overview --------- -MPC8569MDS is composed of two boards - PB (Processor Board) and PIB (Platform -I/O Board). The mpc8569 PowerTM processor is mounted on PB board. - -Building U-boot ------------ - make MPC8569MDS_config - make - -Memory Map ----------- -0x0000_0000 0x7fff_ffff DDR 2G -0xa000_0000 0xbfff_ffff PCIe MEM 512MB -0xe000_0000 0xe00f_ffff CCSRBAR 1M -0xe280_0000 0xe2ff_ffff PCIe I/O 8M -0xc000_0000 0xdfff_ffff SRIO 512MB -0xf000_0000 0xf3ff_ffff SDRAM 64MB -0xf800_0000 0xf800_7fff BCSR 32KB -0xf800_8000 0xf800_ffff PIB (CS4) 32KB -0xf801_0000 0xf801_7fff PIB (CS5) 32KB -0xfe00_0000 0xffff_ffff Flash 32MB - - -Flashing u-boot Images ---------------- - -Use the following commands to program u-boot image into flash: - - => tftp 1000000 u-boot.bin - => protect off all - => erase fff80000 ffffffff - => cp.b 1000000 fff80000 80000 - - -Setting the correct MAC addresses ------------------------ -The command - "mac", is introduced to set on-board system EEPROM in the format -defined in board/freescale/common/sys_eeprom.c. we must set all 8 MAC -addresses for the MPC8569MDS's 8 Ethernet ports and save it by "mac save" when -we first get the board. The commands are as follows: - => mac i NXID /* Set NXID to this EEPROM */ - => mac e 01 /* Set Errata, this value is not defined by hardware - designer, we can set whatever we want */ - => mac n a0 /* Set Serial Number. This is not defined by hardware - designer, we can set whatever we want */ - => mac date 090512080000 /* Set the date in YYMMDDhhmmss format */ - - => mac p 8 /* Set the number of mac ports, it should be 8 */ - => mac 0 xx:xx:xx:xx:xx:xx /* xx:xx:xx:xx:xx:xx should be the real mac - address, you can refer to the value on - the sticker of the rear side of the board - */ - ..... - => mac 7 xx:xx:xx:xx:xx:xx - => mac read - => mac save - -After resetting the board, the ethxaddrs will be filled with the mac addresses -if such environment variables are blank(never been set before). If the ethxaddr -has been set but we want to update it, we can use the following commands: - => setenv ethxaddr /* x = "none",1,2,3,4,5,6,7 */ - => save - => reset - - -Programming the ucode to flash ---------------------------------- -MPC8569 doesn't have ROM in QE, so we must upload the microcode(ucode) to QE's -IRAM so that the QE can work. The ucode binary can be downloaded from -http://opensource.freescale.com/firmware/, and it must be programmed to -the address 0xfff0000 in the flash. Otherwise, the QE can't work and uboot -hangs at "Net:" - - -Please note the above two steps(setting mac addresses and programming ucode) are -very important to get the board booting up and working properly. |