diff options
Diffstat (limited to 'cpu/ppc4xx/44x_spd_ddr2.c')
| -rw-r--r-- | cpu/ppc4xx/44x_spd_ddr2.c | 317 |
1 files changed, 193 insertions, 124 deletions
diff --git a/cpu/ppc4xx/44x_spd_ddr2.c b/cpu/ppc4xx/44x_spd_ddr2.c index 15250d470da..b40e4b15150 100644 --- a/cpu/ppc4xx/44x_spd_ddr2.c +++ b/cpu/ppc4xx/44x_spd_ddr2.c @@ -60,7 +60,25 @@ "SDRAM_" #mnemonic, SDRAM_##mnemonic, data); \ } while (0) -static inline void ppc4xx_ibm_ddr2_register_dump(void); +#if defined(CONFIG_440) +/* + * This DDR2 setup code can dynamically setup the TLB entries for the DDR2 + * memory region. Right now the cache should still be disabled in U-Boot + * because of the EMAC driver, that need its buffer descriptor to be located + * in non cached memory. + * + * If at some time this restriction doesn't apply anymore, just define + * CONFIG_4xx_DCACHE in the board config file and this code should setup + * everything correctly. + */ +#ifdef CONFIG_4xx_DCACHE +/* enable caching on SDRAM */ +#define MY_TLB_WORD2_I_ENABLE 0 +#else +/* disable caching on SDRAM */ +#define MY_TLB_WORD2_I_ENABLE TLB_WORD2_I_ENABLE +#endif /* CONFIG_4xx_DCACHE */ +#endif /* CONFIG_440 */ #if defined(CONFIG_SPD_EEPROM) @@ -133,22 +151,6 @@ static inline void ppc4xx_ibm_ddr2_register_dump(void); #define NUMLOOPS 64 /* memory test loops */ /* - * This DDR2 setup code can dynamically setup the TLB entries for the DDR2 memory - * region. Right now the cache should still be disabled in U-Boot because of the - * EMAC driver, that need it's buffer descriptor to be located in non cached - * memory. - * - * If at some time this restriction doesn't apply anymore, just define - * CONFIG_4xx_DCACHE in the board config file and this code should setup - * everything correctly. - */ -#ifdef CONFIG_4xx_DCACHE -#define MY_TLB_WORD2_I_ENABLE 0 /* enable caching on SDRAM */ -#else -#define MY_TLB_WORD2_I_ENABLE TLB_WORD2_I_ENABLE /* disable caching on SDRAM */ -#endif - -/* * Newer PPC's like 440SPe, 460EX/GT can be equipped with more than 2GB of SDRAM. * To support such configurations, we "only" map the first 2GB via the TLB's. We * need some free virtual address space for the remaining peripherals like, SoC @@ -260,62 +262,19 @@ static void program_ecc_addr(unsigned long start_address, unsigned long num_bytes, unsigned long tlb_word2_i_value); #endif +#if !defined(CONFIG_PPC4xx_DDR_AUTOCALIBRATION) static void program_DQS_calibration(unsigned long *dimm_populated, - unsigned char *iic0_dimm_addr, - unsigned long num_dimm_banks); + unsigned char *iic0_dimm_addr, + unsigned long num_dimm_banks); #ifdef HARD_CODED_DQS /* calibration test with hardvalues */ static void test(void); #else static void DQS_calibration_process(void); #endif +#endif int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]); void dcbz_area(u32 start_address, u32 num_bytes); -static u32 mfdcr_any(u32 dcr) -{ - u32 val; - - switch (dcr) { - case SDRAM_R0BAS + 0: - val = mfdcr(SDRAM_R0BAS + 0); - break; - case SDRAM_R0BAS + 1: - val = mfdcr(SDRAM_R0BAS + 1); - break; - case SDRAM_R0BAS + 2: - val = mfdcr(SDRAM_R0BAS + 2); - break; - case SDRAM_R0BAS + 3: - val = mfdcr(SDRAM_R0BAS + 3); - break; - default: - printf("DCR %d not defined in case statement!!!\n", dcr); - val = 0; /* just to satisfy the compiler */ - } - - return val; -} - -static void mtdcr_any(u32 dcr, u32 val) -{ - switch (dcr) { - case SDRAM_R0BAS + 0: - mtdcr(SDRAM_R0BAS + 0, val); - break; - case SDRAM_R0BAS + 1: - mtdcr(SDRAM_R0BAS + 1, val); - break; - case SDRAM_R0BAS + 2: - mtdcr(SDRAM_R0BAS + 2, val); - break; - case SDRAM_R0BAS + 3: - mtdcr(SDRAM_R0BAS + 3, val); - break; - default: - printf("DCR %d not defined in case statement!!!\n", dcr); - } -} - static unsigned char spd_read(uchar chip, uint addr) { unsigned char data[2]; @@ -447,8 +406,8 @@ phys_size_t initdram(int board_type) */ /* switch to correct I2C bus */ - I2C_SET_BUS(CFG_SPD_BUS_NUM); - i2c_init(CFG_I2C_SPEED, CFG_I2C_SLAVE); + I2C_SET_BUS(CONFIG_SYS_SPD_BUS_NUM); + i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); /*------------------------------------------------------------------ * Clear out the serial presence detect buffers. @@ -609,7 +568,11 @@ phys_size_t initdram(int board_type) /*------------------------------------------------------------------ * DQS calibration. *-----------------------------------------------------------------*/ +#if defined(CONFIG_PPC4xx_DDR_AUTOCALIBRATION) + DQS_autocalibration(); +#else program_DQS_calibration(dimm_populated, iic0_dimm_addr, num_dimm_banks); +#endif #ifdef CONFIG_DDR_ECC /*------------------------------------------------------------------ @@ -2302,10 +2265,12 @@ static void program_memory_queue(unsigned long *dimm_populated, /* * Set optimal value for Memory Queue HB/LL Configuration registers */ - mtdcr(SDRAM_CONF1HB, mfdcr(SDRAM_CONF1HB) | SDRAM_CONF1HB_AAFR | - SDRAM_CONF1HB_RPEN | SDRAM_CONF1HB_RFTE); - mtdcr(SDRAM_CONF1LL, mfdcr(SDRAM_CONF1LL) | SDRAM_CONF1LL_AAFR | - SDRAM_CONF1LL_RPEN | SDRAM_CONF1LL_RFTE); + mtdcr(SDRAM_CONF1HB, (mfdcr(SDRAM_CONF1HB) & ~SDRAM_CONF1HB_MASK) | + SDRAM_CONF1HB_AAFR | SDRAM_CONF1HB_RPEN | SDRAM_CONF1HB_RFTE | + SDRAM_CONF1HB_RPLM | SDRAM_CONF1HB_WRCL); + mtdcr(SDRAM_CONF1LL, (mfdcr(SDRAM_CONF1LL) & ~SDRAM_CONF1LL_MASK) | + SDRAM_CONF1LL_AAFR | SDRAM_CONF1LL_RPEN | SDRAM_CONF1LL_RFTE | + SDRAM_CONF1LL_RPLM); mtdcr(SDRAM_CONFPATHB, mfdcr(SDRAM_CONFPATHB) | SDRAM_CONFPATHB_TPEN); #endif } @@ -2329,18 +2294,6 @@ static unsigned long is_ecc_enabled(void) return ecc; } -static void blank_string(int size) -{ - int i; - - for (i=0; i<size; i++) - putc('\b'); - for (i=0; i<size; i++) - putc(' '); - for (i=0; i<size; i++) - putc('\b'); -} - #ifdef CONFIG_DDR_ECC /*-----------------------------------------------------------------------------+ * program_ecc. @@ -2468,6 +2421,7 @@ static void program_ecc_addr(unsigned long start_address, } #endif +#if !defined(CONFIG_PPC4xx_DDR_AUTOCALIBRATION) /*-----------------------------------------------------------------------------+ * program_DQS_calibration. *-----------------------------------------------------------------------------*/ @@ -3001,15 +2955,17 @@ static void test(void) (ppcMfdcr_sdram(SDRAM_MCOPT1) & ~SDRAM_MCOPT1_MCHK_MASK) | ecc_temp); } -#endif +#endif /* !HARD_CODED_DQS */ +#endif /* !defined(CONFIG_PPC4xx_DDR_AUTOCALIBRATION) */ #else /* CONFIG_SPD_EEPROM */ /*----------------------------------------------------------------------------- * Function: initdram - * Description: Configures the PPC405EX(r) DDR1/DDR2 SDRAM memory - * banks. The configuration is performed using static, compile- + * Description: Configures the PPC4xx IBM DDR1/DDR2 SDRAM memory controller. + * The configuration is performed using static, compile- * time parameters. + * Configures the PPC405EX(r) and PPC460EX/GT *---------------------------------------------------------------------------*/ phys_size_t initdram(int board_type) { @@ -3025,64 +2981,76 @@ phys_size_t initdram(int board_type) #if !defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) unsigned long val; +#if defined(CONFIG_440) + mtdcr(SDRAM_R0BAS, CONFIG_SYS_SDRAM_R0BAS); + mtdcr(SDRAM_R1BAS, CONFIG_SYS_SDRAM_R1BAS); + mtdcr(SDRAM_R2BAS, CONFIG_SYS_SDRAM_R2BAS); + mtdcr(SDRAM_R3BAS, CONFIG_SYS_SDRAM_R3BAS); + mtdcr(SDRAM_PLBADDULL, CONFIG_SYS_SDRAM_PLBADDULL); /* MQ0_BAUL */ + mtdcr(SDRAM_PLBADDUHB, CONFIG_SYS_SDRAM_PLBADDUHB); /* MQ0_BAUH */ + mtdcr(SDRAM_CONF1LL, CONFIG_SYS_SDRAM_CONF1LL); + mtdcr(SDRAM_CONF1HB, CONFIG_SYS_SDRAM_CONF1HB); + mtdcr(SDRAM_CONFPATHB, CONFIG_SYS_SDRAM_CONFPATHB); +#endif + /* Set Memory Bank Configuration Registers */ - mtsdram(SDRAM_MB0CF, CFG_SDRAM0_MB0CF); - mtsdram(SDRAM_MB1CF, CFG_SDRAM0_MB1CF); - mtsdram(SDRAM_MB2CF, CFG_SDRAM0_MB2CF); - mtsdram(SDRAM_MB3CF, CFG_SDRAM0_MB3CF); + mtsdram(SDRAM_MB0CF, CONFIG_SYS_SDRAM0_MB0CF); + mtsdram(SDRAM_MB1CF, CONFIG_SYS_SDRAM0_MB1CF); + mtsdram(SDRAM_MB2CF, CONFIG_SYS_SDRAM0_MB2CF); + mtsdram(SDRAM_MB3CF, CONFIG_SYS_SDRAM0_MB3CF); /* Set Memory Clock Timing Register */ - mtsdram(SDRAM_CLKTR, CFG_SDRAM0_CLKTR); + mtsdram(SDRAM_CLKTR, CONFIG_SYS_SDRAM0_CLKTR); /* Set Refresh Time Register */ - mtsdram(SDRAM_RTR, CFG_SDRAM0_RTR); + mtsdram(SDRAM_RTR, CONFIG_SYS_SDRAM0_RTR); /* Set SDRAM Timing Registers */ - mtsdram(SDRAM_SDTR1, CFG_SDRAM0_SDTR1); - mtsdram(SDRAM_SDTR2, CFG_SDRAM0_SDTR2); - mtsdram(SDRAM_SDTR3, CFG_SDRAM0_SDTR3); + mtsdram(SDRAM_SDTR1, CONFIG_SYS_SDRAM0_SDTR1); + mtsdram(SDRAM_SDTR2, CONFIG_SYS_SDRAM0_SDTR2); + mtsdram(SDRAM_SDTR3, CONFIG_SYS_SDRAM0_SDTR3); /* Set Mode and Extended Mode Registers */ - mtsdram(SDRAM_MMODE, CFG_SDRAM0_MMODE); - mtsdram(SDRAM_MEMODE, CFG_SDRAM0_MEMODE); + mtsdram(SDRAM_MMODE, CONFIG_SYS_SDRAM0_MMODE); + mtsdram(SDRAM_MEMODE, CONFIG_SYS_SDRAM0_MEMODE); /* Set Memory Controller Options 1 Register */ - mtsdram(SDRAM_MCOPT1, CFG_SDRAM0_MCOPT1); + mtsdram(SDRAM_MCOPT1, CONFIG_SYS_SDRAM0_MCOPT1); /* Set Manual Initialization Control Registers */ - mtsdram(SDRAM_INITPLR0, CFG_SDRAM0_INITPLR0); - mtsdram(SDRAM_INITPLR1, CFG_SDRAM0_INITPLR1); - mtsdram(SDRAM_INITPLR2, CFG_SDRAM0_INITPLR2); - mtsdram(SDRAM_INITPLR3, CFG_SDRAM0_INITPLR3); - mtsdram(SDRAM_INITPLR4, CFG_SDRAM0_INITPLR4); - mtsdram(SDRAM_INITPLR5, CFG_SDRAM0_INITPLR5); - mtsdram(SDRAM_INITPLR6, CFG_SDRAM0_INITPLR6); - mtsdram(SDRAM_INITPLR7, CFG_SDRAM0_INITPLR7); - mtsdram(SDRAM_INITPLR8, CFG_SDRAM0_INITPLR8); - mtsdram(SDRAM_INITPLR9, CFG_SDRAM0_INITPLR9); - mtsdram(SDRAM_INITPLR10, CFG_SDRAM0_INITPLR10); - mtsdram(SDRAM_INITPLR11, CFG_SDRAM0_INITPLR11); - mtsdram(SDRAM_INITPLR12, CFG_SDRAM0_INITPLR12); - mtsdram(SDRAM_INITPLR13, CFG_SDRAM0_INITPLR13); - mtsdram(SDRAM_INITPLR14, CFG_SDRAM0_INITPLR14); - mtsdram(SDRAM_INITPLR15, CFG_SDRAM0_INITPLR15); + mtsdram(SDRAM_INITPLR0, CONFIG_SYS_SDRAM0_INITPLR0); + mtsdram(SDRAM_INITPLR1, CONFIG_SYS_SDRAM0_INITPLR1); + mtsdram(SDRAM_INITPLR2, CONFIG_SYS_SDRAM0_INITPLR2); + mtsdram(SDRAM_INITPLR3, CONFIG_SYS_SDRAM0_INITPLR3); + mtsdram(SDRAM_INITPLR4, CONFIG_SYS_SDRAM0_INITPLR4); + mtsdram(SDRAM_INITPLR5, CONFIG_SYS_SDRAM0_INITPLR5); + mtsdram(SDRAM_INITPLR6, CONFIG_SYS_SDRAM0_INITPLR6); + mtsdram(SDRAM_INITPLR7, CONFIG_SYS_SDRAM0_INITPLR7); + mtsdram(SDRAM_INITPLR8, CONFIG_SYS_SDRAM0_INITPLR8); + mtsdram(SDRAM_INITPLR9, CONFIG_SYS_SDRAM0_INITPLR9); + mtsdram(SDRAM_INITPLR10, CONFIG_SYS_SDRAM0_INITPLR10); + mtsdram(SDRAM_INITPLR11, CONFIG_SYS_SDRAM0_INITPLR11); + mtsdram(SDRAM_INITPLR12, CONFIG_SYS_SDRAM0_INITPLR12); + mtsdram(SDRAM_INITPLR13, CONFIG_SYS_SDRAM0_INITPLR13); + mtsdram(SDRAM_INITPLR14, CONFIG_SYS_SDRAM0_INITPLR14); + mtsdram(SDRAM_INITPLR15, CONFIG_SYS_SDRAM0_INITPLR15); /* Set On-Die Termination Registers */ - mtsdram(SDRAM_CODT, CFG_SDRAM0_CODT); - mtsdram(SDRAM_MODT0, CFG_SDRAM0_MODT0); - mtsdram(SDRAM_MODT1, CFG_SDRAM0_MODT1); + mtsdram(SDRAM_CODT, CONFIG_SYS_SDRAM0_CODT); + mtsdram(SDRAM_MODT0, CONFIG_SYS_SDRAM0_MODT0); + mtsdram(SDRAM_MODT1, CONFIG_SYS_SDRAM0_MODT1); /* Set Write Timing Register */ - mtsdram(SDRAM_WRDTR, CFG_SDRAM0_WRDTR); + mtsdram(SDRAM_WRDTR, CONFIG_SYS_SDRAM0_WRDTR); /* * Start Initialization by SDRAM0_MCOPT2[SREN] = 0 and @@ -3103,10 +3071,13 @@ phys_size_t initdram(int board_type) /* Set Delay Control Registers */ - mtsdram(SDRAM_DLCR, CFG_SDRAM0_DLCR); - mtsdram(SDRAM_RDCC, CFG_SDRAM0_RDCC); - mtsdram(SDRAM_RQDC, CFG_SDRAM0_RQDC); - mtsdram(SDRAM_RFDC, CFG_SDRAM0_RFDC); + mtsdram(SDRAM_DLCR, CONFIG_SYS_SDRAM0_DLCR); + +#if !defined(CONFIG_PPC4xx_DDR_AUTOCALIBRATION) + mtsdram(SDRAM_RDCC, CONFIG_SYS_SDRAM0_RDCC); + mtsdram(SDRAM_RQDC, CONFIG_SYS_SDRAM0_RQDC); + mtsdram(SDRAM_RFDC, CONFIG_SYS_SDRAM0_RFDC); +#endif /* !CONFIG_PPC4xx_DDR_AUTOCALIBRATION */ /* * Enable Controller by SDRAM0_MCOPT2[DCEN] = 1: @@ -3115,18 +3086,116 @@ phys_size_t initdram(int board_type) mfsdram(SDRAM_MCOPT2, val); mtsdram(SDRAM_MCOPT2, val | SDRAM_MCOPT2_DCEN_ENABLE); +#if defined(CONFIG_440) + /* + * Program TLB entries with caches enabled, for best performace + * while auto-calibrating and ECC generation + */ + program_tlb(0, 0, (CONFIG_SYS_MBYTES_SDRAM << 20), 0); +#endif + +#if defined(CONFIG_PPC4xx_DDR_AUTOCALIBRATION) +#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) + /*------------------------------------------------------------------ + | DQS calibration. + +-----------------------------------------------------------------*/ + DQS_autocalibration(); +#endif /* !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) */ +#endif /* CONFIG_PPC4xx_DDR_AUTOCALIBRATION */ + #if defined(CONFIG_DDR_ECC) - ecc_init(CFG_SDRAM_BASE, CFG_MBYTES_SDRAM << 20); + ecc_init(CONFIG_SYS_SDRAM_BASE, CONFIG_SYS_MBYTES_SDRAM << 20); #endif /* defined(CONFIG_DDR_ECC) */ +#if defined(CONFIG_440) + /* + * Now after initialization (auto-calibration and ECC generation) + * remove the TLB entries with caches enabled and program again with + * desired cache functionality + */ + remove_tlb(0, (CONFIG_SYS_MBYTES_SDRAM << 20)); + program_tlb(0, 0, (CONFIG_SYS_MBYTES_SDRAM << 20), MY_TLB_WORD2_I_ENABLE); +#endif + ppc4xx_ibm_ddr2_register_dump(); + +#if defined(CONFIG_PPC4xx_DDR_AUTOCALIBRATION) + /* + * Clear potential errors resulting from auto-calibration. + * If not done, then we could get an interrupt later on when + * exceptions are enabled. + */ + set_mcsr(get_mcsr()); +#endif /* CONFIG_PPC4xx_DDR_AUTOCALIBRATION */ + #endif /* !defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) */ - return (CFG_MBYTES_SDRAM << 20); + return (CONFIG_SYS_MBYTES_SDRAM << 20); } #endif /* CONFIG_SPD_EEPROM */ -static inline void ppc4xx_ibm_ddr2_register_dump(void) +#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) +#if defined(CONFIG_440) +u32 mfdcr_any(u32 dcr) +{ + u32 val; + + switch (dcr) { + case SDRAM_R0BAS + 0: + val = mfdcr(SDRAM_R0BAS + 0); + break; + case SDRAM_R0BAS + 1: + val = mfdcr(SDRAM_R0BAS + 1); + break; + case SDRAM_R0BAS + 2: + val = mfdcr(SDRAM_R0BAS + 2); + break; + case SDRAM_R0BAS + 3: + val = mfdcr(SDRAM_R0BAS + 3); + break; + default: + printf("DCR %d not defined in case statement!!!\n", dcr); + val = 0; /* just to satisfy the compiler */ + } + + return val; +} + +void mtdcr_any(u32 dcr, u32 val) +{ + switch (dcr) { + case SDRAM_R0BAS + 0: + mtdcr(SDRAM_R0BAS + 0, val); + break; + case SDRAM_R0BAS + 1: + mtdcr(SDRAM_R0BAS + 1, val); + break; + case SDRAM_R0BAS + 2: + mtdcr(SDRAM_R0BAS + 2, val); + break; + case SDRAM_R0BAS + 3: + mtdcr(SDRAM_R0BAS + 3, val); + break; + default: + printf("DCR %d not defined in case statement!!!\n", dcr); + } +} +#endif /* defined(CONFIG_440) */ + +void blank_string(int size) +{ + int i; + + for (i = 0; i < size; i++) + putc('\b'); + for (i = 0; i < size; i++) + putc(' '); + for (i = 0; i < size; i++) + putc('\b'); +} +#endif /* !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) */ + +inline void ppc4xx_ibm_ddr2_register_dump(void) { #if defined(DEBUG) printf("\nPPC4xx IBM DDR2 Register Dump:\n"); |