diff options
Diffstat (limited to 'cpu/arm_cortexa8/mx6/generic.c')
| -rw-r--r-- | cpu/arm_cortexa8/mx6/generic.c | 103 |
1 files changed, 103 insertions, 0 deletions
diff --git a/cpu/arm_cortexa8/mx6/generic.c b/cpu/arm_cortexa8/mx6/generic.c index bf796138b0..7a42a5f70a 100644 --- a/cpu/arm_cortexa8/mx6/generic.c +++ b/cpu/arm_cortexa8/mx6/generic.c @@ -82,6 +82,14 @@ enum pll_clocks { #define NFC_CLK_MAX PLL2_FREQ_MAX #endif +#define OCOTP_THERMAL_OFFSET 0x4E0 +#define TEMPERATURE_MIN -25 +#define TEMPERATURE_HOT 80 +#define TEMPERATURE_MAX 125 +#define REG_VALUE_TO_CEL(ratio, raw) ((raw_n25c - raw) * 100 / ratio - 25) +static int cpu_tmp; +static unsigned int fuse; + #define SNVS_LPGPR_OFFSET 0x68 static u32 __decode_pll(enum pll_clocks pll, u32 infreq) @@ -792,6 +800,98 @@ int clk_config(u32 ref, u32 freq, u32 clk_type) } #endif +int read_cpu_temperature(void) +{ + unsigned int reg, tmp, temperature, i; + unsigned int raw_25c, raw_hot, hot_temp, raw_n25c, ratio; + unsigned int ccm_ccgr2; + + ccm_ccgr2 = readl(MXC_CCM_CCGR2); + writel(readl(MXC_CCM_CCGR2) | (0x3 << MXC_CCM_CCGR2_CG6_OFFSET), + MXC_CCM_CCGR2); + fuse = readl(OCOTP_BASE_ADDR + OCOTP_THERMAL_OFFSET); + writel(ccm_ccgr2, MXC_CCM_CCGR2); + if (fuse == 0 || fuse == 0xffffffff) + return TEMPERATURE_MIN; + + /* Fuse data layout: + * [31:20] sensor value @ 25C + * [19:8] sensor value of hot + * [7:0] hot temperature value */ + raw_25c = fuse >> 20; + raw_hot = (fuse & 0xfff00) >> 8; + hot_temp = fuse & 0xff; + + ratio = ((raw_25c - raw_hot) * 100) / (hot_temp - 25); + raw_n25c = raw_25c + ratio / 2; + + /* now we only using single measure, every time we measure + the temperature, we will power on/down the anadig module*/ + writel(BM_ANADIG_TEMPSENSE0_POWER_DOWN, + ANATOP_BASE_ADDR + HW_ANADIG_TEMPSENSE0_CLR); + writel(BM_ANADIG_ANA_MISC0_REFTOP_SELBIASOFF, + ANATOP_BASE_ADDR + HW_ANADIG_ANA_MISC0_SET); + + /* write measure freq */ + reg = readl(ANATOP_BASE_ADDR + HW_ANADIG_TEMPSENSE1); + reg &= ~BM_ANADIG_TEMPSENSE1_MEASURE_FREQ; + reg |= 327; + writel(reg, ANATOP_BASE_ADDR + HW_ANADIG_TEMPSENSE1); + + writel(BM_ANADIG_TEMPSENSE0_MEASURE_TEMP, + ANATOP_BASE_ADDR + HW_ANADIG_TEMPSENSE0_CLR); + writel(BM_ANADIG_TEMPSENSE0_FINISHED, + ANATOP_BASE_ADDR + HW_ANADIG_TEMPSENSE0_CLR); + writel(BM_ANADIG_TEMPSENSE0_MEASURE_TEMP, + ANATOP_BASE_ADDR + HW_ANADIG_TEMPSENSE0_SET); + + tmp = 0; + /* read five times of temperature values to get average*/ + for (i = 0; i < 5; i++) { + while ((readl(ANATOP_BASE_ADDR + HW_ANADIG_TEMPSENSE0) + & BM_ANADIG_TEMPSENSE0_FINISHED) == 0) + udelay(10000); + reg = readl(ANATOP_BASE_ADDR + HW_ANADIG_TEMPSENSE0); + tmp += (reg & BM_ANADIG_TEMPSENSE0_TEMP_VALUE) + >> BP_ANADIG_TEMPSENSE0_TEMP_VALUE; + writel(BM_ANADIG_TEMPSENSE0_FINISHED, + ANATOP_BASE_ADDR + HW_ANADIG_TEMPSENSE0_CLR); + } + + tmp = tmp / 5; + if (tmp <= raw_n25c) + temperature = REG_VALUE_TO_CEL(ratio, tmp); + else + temperature = TEMPERATURE_MIN; + /* power down anatop thermal sensor */ + writel(BM_ANADIG_TEMPSENSE0_POWER_DOWN, + ANATOP_BASE_ADDR + HW_ANADIG_TEMPSENSE0_SET); + writel(BM_ANADIG_ANA_MISC0_REFTOP_SELBIASOFF, + ANATOP_BASE_ADDR + HW_ANADIG_ANA_MISC0_CLR); + + return temperature; + +} + +void check_cpu_temperature(void) +{ + cpu_tmp = read_cpu_temperature(); + while (cpu_tmp > TEMPERATURE_MIN && cpu_tmp < TEMPERATURE_MAX) { + if (cpu_tmp >= TEMPERATURE_HOT) { + printf("CPU is %d C, too hot to boot, waiting...\n", + cpu_tmp); + udelay(5000000); + cpu_tmp = read_cpu_temperature(); + } else + break; + } + if (cpu_tmp > TEMPERATURE_MIN && cpu_tmp < TEMPERATURE_MAX) + printf("Temperature: %d C, calibration data 0x%x\n", + cpu_tmp, fuse); + else + printf("Temperature: can't get valid data!\n"); +} + #if defined(CONFIG_DISPLAY_CPUINFO) int print_cpuinfo(void) { @@ -799,6 +899,9 @@ int print_cpuinfo(void) (get_board_rev() & 0xFF) >> 4, (get_board_rev() & 0xF), __get_mcu_main_clk() / SZ_DEC_1M); + + check_cpu_temperature(); + mxc_dump_clocks(); return 0; } |