summaryrefslogtreecommitdiff
path: root/board/work-microwave/work_92105
diff options
context:
space:
mode:
Diffstat (limited to 'board/work-microwave/work_92105')
-rw-r--r--board/work-microwave/work_92105/Kconfig15
-rw-r--r--board/work-microwave/work_92105/MAINTAINERS6
-rw-r--r--board/work-microwave/work_92105/Makefile10
-rw-r--r--board/work-microwave/work_92105/README91
-rw-r--r--board/work-microwave/work_92105/work_92105.c77
-rw-r--r--board/work-microwave/work_92105/work_92105_display.c349
-rw-r--r--board/work-microwave/work_92105/work_92105_display.h14
-rw-r--r--board/work-microwave/work_92105/work_92105_spl.c85
8 files changed, 647 insertions, 0 deletions
diff --git a/board/work-microwave/work_92105/Kconfig b/board/work-microwave/work_92105/Kconfig
new file mode 100644
index 0000000000..74f004f53c
--- /dev/null
+++ b/board/work-microwave/work_92105/Kconfig
@@ -0,0 +1,15 @@
+if TARGET_WORK_92105
+
+config SYS_BOARD
+ default "work_92105"
+
+config SYS_VENDOR
+ default "work-microwave"
+
+config SYS_SOC
+ default "lpc32xx"
+
+config SYS_CONFIG_NAME
+ default "work_92105"
+
+endif
diff --git a/board/work-microwave/work_92105/MAINTAINERS b/board/work-microwave/work_92105/MAINTAINERS
new file mode 100644
index 0000000000..29a92c5ffe
--- /dev/null
+++ b/board/work-microwave/work_92105/MAINTAINERS
@@ -0,0 +1,6 @@
+WORK_92105 BOARD
+M: Albert ARIBAUD <albert.aribaud@3adev.fr>
+S: Maintained
+F: board/work-microwave/work_92105/
+F: include/configs/work_92105.h
+F: configs/work_92105_defconfig
diff --git a/board/work-microwave/work_92105/Makefile b/board/work-microwave/work_92105/Makefile
new file mode 100644
index 0000000000..ba31c8e4f4
--- /dev/null
+++ b/board/work-microwave/work_92105/Makefile
@@ -0,0 +1,10 @@
+#
+# (C) Copyright 2014 DENX Software Engineering GmbH
+# Written-by: Albert ARIBAUD <albert.aribaud@3adev.fr>
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y := work_92105.o work_92105_display.o
+
+obj-$(CONFIG_SPL_BUILD) += work_92105_spl.o
diff --git a/board/work-microwave/work_92105/README b/board/work-microwave/work_92105/README
new file mode 100644
index 0000000000..3c256e0b2c
--- /dev/null
+++ b/board/work-microwave/work_92105/README
@@ -0,0 +1,91 @@
+Work_92105 from Work Microwave is an LPC3250- based board with the
+following features:
+
+ - 64MB SDR DRAM
+ - 1 GB SLC NAND, managed through MLC controller.
+ - Ethernet
+ - Ethernet + PHY SMSC8710
+ - I2C:
+ - EEPROM (24M01-compatible)
+ - RTC (DS1374-compatible)
+ - Temperature sensor (DS620)
+ - DACs (2 x MAX518)
+ - SPI (through SSP interface)
+ - Port expander MAX6957
+ - LCD display (HD44780-compatible), controlled
+ through the port expander and DACs
+
+Standard SPL and U-Boot binaries
+--------------------------------
+
+The default 'make' (or the 'make all') command will produce the
+following files:
+
+1. spl/u-boot-spl.bin SPL, intended to run from SRAM at address 0.
+ This file can be loaded in SRAM through a JTAG
+ debugger or through the LPC32XX Service Boot
+ mechanism.
+
+2. u-boot.bin The raw U-Boot image, which can be loaded in
+ DDR through a JTAG debugger (for instance by
+ breaking SPL after DDR init), or by a running
+ U-Boot through e.g. 'loady' or 'tftp' and then
+ executed with 'go'.
+
+3. u-boot.img A U-Boot image with a mkimage header prepended.
+ SPL assumes (even when loaded through JTAG or
+ Service Boot) that such an image will be found
+ at offset 0x00040000 in NAND.
+
+NAND cold-boot binaries
+-----------------------
+
+The board can boot entirely from power-on with only SPL and U-Boot in
+NAND. The LPC32XX-specific 'make lpc32xx-full.bin' command will produce
+(in addition to spl/u-boot-spl.bin and u-boot.img if they were not made
+already) the following files:
+
+4. lpc32xx-spl.img spl/u-boot-spl.bin, with a LPC32XX boot header
+ prepended. This header is required for the ROM
+ code to load SPL into SRAM and branch into it.
+ The content of this file is expected to reside
+ in NAND at addresses 0x00000000 and 0x00020000
+ (two copies).
+
+5. lpc32xx-boot-0.bin lpc32xx-spl.img, padded with 0xFF bytes to a
+ size of 0x20000 bytes. This file covers exactly
+ the reserved area for the first bootloader copy
+ in NAND.
+
+6. lpc32xx-boot-1.bin Same as lpc32xx-boot-0.bin. This is intended to
+ be used as the second bootloader copy.
+
+7. lpc32xx-full.bin lpc32xx-boot-0.bin, lpc32xx-boot-1.bin and
+ u-boot.img concatenated. This file represents
+ the content of whole bootloader as present in
+ NAND at offset 00x00000000.
+
+Flashing instructions
+---------------------
+
+The following assumes a working U-Boot on the target, with the ability
+to load files into DDR.
+
+To update the whole bootloader:
+
+ nand erase 0x00000000 0x80000
+ (load lpc32xx-full.bin at location $loadaddr)
+ nand write $loadaddr 0x00000000 $filesize
+
+To update SPL only (note the double nand write) :
+
+ nand erase 0x00000000 0x40000
+ (load lpc32xx-spl.img or lpc32xx-boot-N.bin at location $loadaddr)
+ nand write $loadaddr 0x00000000 $filesize
+ nand write $loadaddr 0x00020000 $filesize
+
+To update U-Boot only:
+
+ nand erase 0x00040000 0x40000
+ (load u-boot.img at location $loadaddr)
+ nand write $loadaddr 0x00040000 $filesize
diff --git a/board/work-microwave/work_92105/work_92105.c b/board/work-microwave/work_92105/work_92105.c
new file mode 100644
index 0000000000..f782284d60
--- /dev/null
+++ b/board/work-microwave/work_92105/work_92105.c
@@ -0,0 +1,77 @@
+/*
+ * WORK Microwave work_92105 board support
+ *
+ * (C) Copyright 2014 DENX Software Engineering GmbH
+ * Written-by: Albert ARIBAUD <albert.aribaud@3adev.fr>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/clk.h>
+#include <asm/arch/emc.h>
+#include <asm/arch/wdt.h>
+#include <asm/gpio.h>
+#include <spl.h>
+#include "work_92105_display.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static struct clk_pm_regs *clk = (struct clk_pm_regs *)CLK_PM_BASE;
+static struct wdt_regs *wdt = (struct wdt_regs *)WDT_BASE;
+
+void reset_periph(void)
+{
+ setbits_le32(&clk->timclk_ctrl, CLK_TIMCLK_WATCHDOG);
+ writel(WDTIM_MCTRL_RESFRC1, &wdt->mctrl);
+ udelay(150);
+ writel(0, &wdt->mctrl);
+ clrbits_le32(&clk->timclk_ctrl, CLK_TIMCLK_WATCHDOG);
+}
+
+int board_early_init_f(void)
+{
+ /* initialize serial port for console */
+ lpc32xx_uart_init(CONFIG_SYS_LPC32XX_UART);
+ /* enable I2C, SSP, MAC, NAND */
+ lpc32xx_i2c_init(1); /* only I2C1 has devices, I2C2 has none */
+ lpc32xx_ssp_init();
+ lpc32xx_mac_init();
+ lpc32xx_mlc_nand_init();
+ /* Display must wait until after relocation and devices init */
+ return 0;
+}
+
+#define GPO_19 115
+
+int board_early_init_r(void)
+{
+ /* Set NAND !WP to 1 through GPO_19 */
+ gpio_request(GPO_19, "NAND_nWP");
+ gpio_direction_output(GPO_19, 1);
+
+ /* initialize display */
+ work_92105_display_init();
+
+ return 0;
+}
+
+int board_init(void)
+{
+ reset_periph();
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+
+ return 0;
+}
+
+int dram_init(void)
+{
+ gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
+ CONFIG_SYS_SDRAM_SIZE);
+
+ return 0;
+}
diff --git a/board/work-microwave/work_92105/work_92105_display.c b/board/work-microwave/work_92105/work_92105_display.c
new file mode 100644
index 0000000000..c8b10131f9
--- /dev/null
+++ b/board/work-microwave/work_92105/work_92105_display.c
@@ -0,0 +1,349 @@
+/*
+ * work_92105 display support
+ *
+ * (C) Copyright 2014 DENX Software Engineering GmbH
+ * Written-by: Albert ARIBAUD <albert.aribaud@3adev.fr>
+ *
+ * The work_92105 display is a HD44780-compatible module
+ * controlled through a MAX6957AAX SPI port expander, two
+ * MAX518 I2C DACs and native LPC32xx GPO 15.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/emc.h>
+#include <asm/gpio.h>
+#include <spi.h>
+#include <i2c.h>
+#include <version.h>
+#include <vsprintf.h>
+
+/*
+ * GPO 15 in port 3 is gpio 3*32+15 = 111
+ */
+
+#define GPO_15 111
+
+/**
+ * MAX6957AAX registers that we will be using
+ */
+
+#define MAX6957_CONF 0x04
+
+#define MAX6957_CONF_08_11 0x0A
+#define MAX6957_CONF_12_15 0x0B
+#define MAX6957_CONF_16_19 0x0C
+
+/**
+ * Individual gpio ports (one per gpio) to HD44780
+ */
+
+#define MAX6957AAX_HD44780_RS 0x29
+#define MAX6957AAX_HD44780_R_W 0x2A
+#define MAX6957AAX_HD44780_EN 0x2B
+#define MAX6957AAX_HD44780_DATA 0x4C
+
+/**
+ * Display controller instructions
+ */
+
+/* Function set: eight bits, two lines, 8-dot font */
+#define HD44780_FUNCTION_SET 0x38
+
+/* Display ON / OFF: turn display on */
+#define HD44780_DISPLAY_ON_OFF_CONTROL 0x0C
+
+/* Entry mode: increment */
+#define HD44780_ENTRY_MODE_SET 0x06
+
+/* Clear */
+#define HD44780_CLEAR_DISPLAY 0x01
+
+/* Set DDRAM addr (to be ORed with exact address) */
+#define HD44780_SET_DDRAM_ADDR 0x80
+
+/* Set CGRAM addr (to be ORed with exact address) */
+#define HD44780_SET_CGRAM_ADDR 0x40
+
+/**
+ * Default value for contrats
+ */
+
+#define CONTRAST_DEFAULT 25
+
+/**
+ * Define slave as a module-wide local to save passing it around,
+ * plus we will need it after init for the "hd44780" command.
+ */
+
+static struct spi_slave *slave;
+
+/*
+ * Write a value into a MAX6957AAX register.
+ */
+
+static void max6957aax_write(uint8_t reg, uint8_t value)
+{
+ uint8_t dout[2];
+
+ dout[0] = reg;
+ dout[1] = value;
+ gpio_set_value(GPO_15, 0);
+ /* do SPI read/write (passing din==dout is OK) */
+ spi_xfer(slave, 16, dout, dout, SPI_XFER_BEGIN | SPI_XFER_END);
+ gpio_set_value(GPO_15, 1);
+}
+
+/*
+ * Read a value from a MAX6957AAX register.
+ *
+ * According to the MAX6957AAX datasheet, we should release the chip
+ * select halfway through the read sequence, when the actual register
+ * value is read; but the WORK_92105 hardware prevents the MAX6957AAX
+ * SPI OUT from reaching the LPC32XX SIP MISO if chip is not selected.
+ * so let's release the CS an hold it again while reading the result.
+ */
+
+static uint8_t max6957aax_read(uint8_t reg)
+{
+ uint8_t dout[2], din[2];
+
+ /* send read command */
+ dout[0] = reg | 0x80; /* set bit 7 to indicate read */
+ dout[1] = 0;
+ gpio_set_value(GPO_15, 0);
+ /* do SPI read/write (passing din==dout is OK) */
+ spi_xfer(slave, 16, dout, dout, SPI_XFER_BEGIN | SPI_XFER_END);
+ /* latch read command */
+ gpio_set_value(GPO_15, 1);
+ /* read register -- din = noop on xmit, din[1] = reg on recv */
+ din[0] = 0;
+ din[1] = 0;
+ gpio_set_value(GPO_15, 0);
+ /* do SPI read/write (passing din==dout is OK) */
+ spi_xfer(slave, 16, din, din, SPI_XFER_BEGIN | SPI_XFER_END);
+ /* end of read. */
+ gpio_set_value(GPO_15, 1);
+ return din[1];
+}
+
+static void hd44780_instruction(unsigned long instruction)
+{
+ max6957aax_write(MAX6957AAX_HD44780_RS, 0);
+ max6957aax_write(MAX6957AAX_HD44780_R_W, 0);
+ max6957aax_write(MAX6957AAX_HD44780_EN, 1);
+ max6957aax_write(MAX6957AAX_HD44780_DATA, instruction);
+ max6957aax_write(MAX6957AAX_HD44780_EN, 0);
+ /* HD44780 takes 37 us for most instructions, 1520 for clear */
+ if (instruction == HD44780_CLEAR_DISPLAY)
+ udelay(2000);
+ else
+ udelay(100);
+}
+
+static void hd44780_write_char(char c)
+{
+ max6957aax_write(MAX6957AAX_HD44780_RS, 1);
+ max6957aax_write(MAX6957AAX_HD44780_R_W, 0);
+ max6957aax_write(MAX6957AAX_HD44780_EN, 1);
+ max6957aax_write(MAX6957AAX_HD44780_DATA, c);
+ max6957aax_write(MAX6957AAX_HD44780_EN, 0);
+ /* HD44780 takes 37 us to write to DDRAM or CGRAM */
+ udelay(100);
+}
+
+static void hd44780_write_str(char *s)
+{
+ max6957aax_write(MAX6957AAX_HD44780_RS, 1);
+ max6957aax_write(MAX6957AAX_HD44780_R_W, 0);
+ while (*s) {
+ max6957aax_write(MAX6957AAX_HD44780_EN, 1);
+ max6957aax_write(MAX6957AAX_HD44780_DATA, *s);
+ max6957aax_write(MAX6957AAX_HD44780_EN, 0);
+ s++;
+ /* HD44780 takes 37 us to write to DDRAM or CGRAM */
+ udelay(100);
+ }
+}
+
+/*
+ * Existing user code might expect these custom characters to be
+ * recognized and displayed on the LCD
+ */
+
+static u8 char_gen_chars[] = {
+ /* #8, empty rectangle */
+ 0x1F, 0x11, 0x11, 0x11, 0x11, 0x11, 0x11, 0x1F,
+ /* #9, filled right arrow */
+ 0x10, 0x18, 0x1C, 0x1E, 0x1C, 0x18, 0x10, 0x00,
+ /* #10, filled left arrow */
+ 0x01, 0x03, 0x07, 0x0F, 0x07, 0x03, 0x01, 0x00,
+ /* #11, up and down arrow */
+ 0x04, 0x0E, 0x1F, 0x00, 0x00, 0x1F, 0x0E, 0x04,
+ /* #12, plus/minus */
+ 0x04, 0x04, 0x1F, 0x04, 0x04, 0x00, 0x1F, 0x00,
+ /* #13, fat exclamation mark */
+ 0x06, 0x06, 0x06, 0x06, 0x00, 0x06, 0x06, 0x00,
+ /* #14, empty square */
+ 0x00, 0x1F, 0x11, 0x11, 0x11, 0x1F, 0x00, 0x00,
+ /* #15, struck out square */
+ 0x00, 0x1F, 0x19, 0x15, 0x13, 0x1F, 0x00, 0x00,
+};
+
+static void hd44780_init_char_gen(void)
+{
+ int i;
+
+ hd44780_instruction(HD44780_SET_CGRAM_ADDR);
+
+ for (i = 0; i < sizeof(char_gen_chars); i++)
+ hd44780_write_char(char_gen_chars[i]);
+
+ hd44780_instruction(HD44780_SET_DDRAM_ADDR);
+}
+
+void work_92105_display_init(void)
+{
+ int claim_err;
+ char *display_contrast_str;
+ uint8_t display_contrast = CONTRAST_DEFAULT;
+ uint8_t enable_backlight = 0x96;
+
+ slave = spi_setup_slave(0, 0, 500000, 0);
+
+ if (!slave) {
+ printf("Failed to set up SPI slave\n");
+ return;
+ }
+
+ claim_err = spi_claim_bus(slave);
+
+ if (claim_err)
+ debug("Failed to claim SPI bus: %d\n", claim_err);
+
+ /* enable backlight */
+ i2c_write(0x2c, 0x01, 1, &enable_backlight, 1);
+
+ /* set display contrast */
+ display_contrast_str = getenv("fwopt_dispcontrast");
+ if (display_contrast_str)
+ display_contrast = simple_strtoul(display_contrast_str,
+ NULL, 10);
+ i2c_write(0x2c, 0x00, 1, &display_contrast, 1);
+
+ /* request GPO_15 as an output initially set to 1 */
+ gpio_request(GPO_15, "MAX6957_nCS");
+ gpio_direction_output(GPO_15, 1);
+
+ /* enable MAX6957 portexpander */
+ max6957aax_write(MAX6957_CONF, 0x01);
+ /* configure pin 8 as input, pins 9..19 as outputs */
+ max6957aax_write(MAX6957_CONF_08_11, 0x56);
+ max6957aax_write(MAX6957_CONF_12_15, 0x55);
+ max6957aax_write(MAX6957_CONF_16_19, 0x55);
+
+ /* initialize HD44780 */
+ max6957aax_write(MAX6957AAX_HD44780_EN, 0);
+ hd44780_instruction(HD44780_FUNCTION_SET);
+ hd44780_instruction(HD44780_DISPLAY_ON_OFF_CONTROL);
+ hd44780_instruction(HD44780_ENTRY_MODE_SET);
+
+ /* write custom character glyphs */
+ hd44780_init_char_gen();
+
+ /* Show U-Boot version, date and time as a sign-of-life */
+ hd44780_instruction(HD44780_CLEAR_DISPLAY);
+ hd44780_instruction(HD44780_SET_DDRAM_ADDR | 0);
+ hd44780_write_str(U_BOOT_VERSION);
+ hd44780_instruction(HD44780_SET_DDRAM_ADDR | 64);
+ hd44780_write_str(U_BOOT_DATE);
+ hd44780_instruction(HD44780_SET_DDRAM_ADDR | 64 | 20);
+ hd44780_write_str(U_BOOT_TIME);
+}
+
+#ifdef CONFIG_CMD_MAX6957
+
+static int do_max6957aax(cmd_tbl_t *cmdtp, int flag, int argc,
+ char *const argv[])
+{
+ int reg, val;
+
+ if (argc != 3)
+ return CMD_RET_USAGE;
+ switch (argv[1][0]) {
+ case 'r':
+ case 'R':
+ reg = simple_strtoul(argv[2], NULL, 0);
+ val = max6957aax_read(reg);
+ printf("MAX6957 reg 0x%02x read 0x%02x\n", reg, val);
+ return 0;
+ default:
+ reg = simple_strtoul(argv[1], NULL, 0);
+ val = simple_strtoul(argv[2], NULL, 0);
+ max6957aax_write(reg, val);
+ printf("MAX6957 reg 0x%02x wrote 0x%02x\n", reg, val);
+ return 0;
+ }
+ return 1;
+}
+
+#ifdef CONFIG_SYS_LONGHELP
+static char max6957aax_help_text[] =
+ "max6957aax - write or read display register:\n"
+ "\tmax6957aax R|r reg - read display register;\n"
+ "\tmax6957aax reg val - write display register.";
+#endif
+
+U_BOOT_CMD(
+ max6957aax, 6, 1, do_max6957aax,
+ "SPI MAX6957 display write/read",
+ max6957aax_help_text
+);
+#endif /* CONFIG_CMD_MAX6957 */
+
+#ifdef CONFIG_CMD_HD44760
+
+/*
+ * We need the HUSH parser because we need string arguments, and
+ * only HUSH can understand them.
+ */
+
+#if !defined(CONFIG_SYS_HUSH_PARSER)
+#error CONFIG_CMD_HD44760 requires CONFIG_SYS_HUSH_PARSER
+#endif
+
+static int do_hd44780(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[])
+{
+ char *cmd;
+
+ if (argc != 3)
+ return CMD_RET_USAGE;
+
+ cmd = argv[1];
+
+ if (strcasecmp(cmd, "cmd") == 0)
+ hd44780_instruction(simple_strtol(argv[2], NULL, 0));
+ else if (strcasecmp(cmd, "data") == 0)
+ hd44780_write_char(simple_strtol(argv[2], NULL, 0));
+ else if (strcasecmp(cmd, "str") == 0)
+ hd44780_write_str(argv[2]);
+ return 0;
+}
+
+#ifdef CONFIG_SYS_LONGHELP
+static char hd44780_help_text[] =
+ "hd44780 - control LCD driver:\n"
+ "\thd44780 cmd <val> - send command <val> to driver;\n"
+ "\thd44780 data <val> - send data <val> to driver;\n"
+ "\thd44780 str \"<text>\" - send \"<text>\" to driver.";
+#endif
+
+U_BOOT_CMD(
+ hd44780, 6, 1, do_hd44780,
+ "HD44780 LCD driver control",
+ hd44780_help_text
+);
+#endif /* CONFIG_CMD_HD44780 */
diff --git a/board/work-microwave/work_92105/work_92105_display.h b/board/work-microwave/work_92105/work_92105_display.h
new file mode 100644
index 0000000000..dd6e768eaf
--- /dev/null
+++ b/board/work-microwave/work_92105/work_92105_display.h
@@ -0,0 +1,14 @@
+/*
+ * work_92105 display support interface
+ *
+ * (C) Copyright 2014 DENX Software Engineering GmbH
+ * Written-by: Albert ARIBAUD <albert.aribaud@3adev.fr>
+ *
+ * The work_92105 display is a HD44780-compatible module
+ * controlled through a MAX6957AAX SPI port expander, two
+ * MAX518 I2C DACs and native LPC32xx GPO 15.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+void work_92105_display_init(void);
diff --git a/board/work-microwave/work_92105/work_92105_spl.c b/board/work-microwave/work_92105/work_92105_spl.c
new file mode 100644
index 0000000000..282a6dd3a7
--- /dev/null
+++ b/board/work-microwave/work_92105/work_92105_spl.c
@@ -0,0 +1,85 @@
+/*
+ * WORK Microwave work_92105 board support
+ *
+ * (C) Copyright 2014 DENX Software Engineering GmbH
+ * Written-by: Albert ARIBAUD <albert.aribaud@3adev.fr>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/emc.h>
+#include <asm/gpio.h>
+#include <spl.h>
+#include "work_92105_display.h"
+
+struct emc_dram_settings dram_64mb = {
+ .cmddelay = 0x0001C000,
+ .config0 = 0x00005682,
+ .rascas0 = 0x00000302,
+ .rdconfig = 0x00000011,
+ .trp = 52631578,
+ .tras = 20833333,
+ .tsrex = 12500000,
+ .twr = 66666666,
+ .trc = 13888888,
+ .trfc = 10256410,
+ .txsr = 12500000,
+ .trrd = 1,
+ .tmrd = 1,
+ .tcdlr = 0,
+ .refresh = 128000,
+ .mode = 0x00018000,
+ .emode = 0x02000000
+};
+
+const struct emc_dram_settings dram_128mb = {
+ .cmddelay = 0x0001C000,
+ .config0 = 0x00005882,
+ .rascas0 = 0x00000302,
+ .rdconfig = 0x00000011,
+ .trp = 52631578,
+ .tras = 22222222,
+ .tsrex = 8333333,
+ .twr = 66666666,
+ .trc = 14814814,
+ .trfc = 10256410,
+ .txsr = 8333333,
+ .trrd = 1,
+ .tmrd = 1,
+ .tcdlr = 0,
+ .refresh = 128000,
+ .mode = 0x00030000,
+ .emode = 0x02000000
+};
+
+void spl_board_init(void)
+{
+ /* initialize serial port for console */
+ lpc32xx_uart_init(CONFIG_SYS_LPC32XX_UART);
+ /* initialize console */
+ preloader_console_init();
+ /* init DDR and NAND to chainload U-Boot */
+ ddr_init(&dram_128mb);
+ /*
+ * If this is actually a 64MB module, then the highest column
+ * bit in any address will be ignored, and thus address 0x80000000
+ * should be mirrored at address 0x80000800. Test this.
+ */
+ writel(0x31415926, 0x80000000); /* write Pi at 0x80000000 */
+ writel(0x16180339, 0x80000800); /* write Phi at 0x80000800 */
+ if (readl(0x80000000) == 0x16180339) /* check 0x80000000 */ {
+ /* actually 64MB mirrored: reconfigure controller */
+ ddr_init(&dram_64mb);
+ }
+ /* initialize NAND controller to load U-Boot from NAND */
+ lpc32xx_mlc_nand_init();
+}
+
+u32 spl_boot_device(void)
+{
+ return BOOT_DEVICE_NAND;
+}