diff options
Diffstat (limited to 'board/w7o/init.S')
-rw-r--r-- | board/w7o/init.S | 244 |
1 files changed, 0 insertions, 244 deletions
diff --git a/board/w7o/init.S b/board/w7o/init.S deleted file mode 100644 index dfde1499569..00000000000 --- a/board/w7o/init.S +++ /dev/null @@ -1,244 +0,0 @@ -/* - * SPDX-License-Identifier: GPL-2.0 IBM-pibs - */ -#include <config.h> -#include <asm/ppc4xx.h> - -#include <ppc_asm.tmpl> -#include <ppc_defs.h> - -#include <asm/cache.h> -#include <asm/mmu.h> - -/****************************************************************************** - * Function: ext_bus_cntlr_init - * - * Description: Configures EBC Controller and a few basic chip selects. - * - * CS0 is setup to get the Boot Flash out of the addresss range - * so that we may setup a stack. CS7 is setup so that we can - * access and reset the hardware watchdog. - * - * IMPORTANT: For pass1 this code must run from - * cache since you can not reliably change a peripheral banks - * timing register (pbxap) while running code from that bank. - * For ex., since we are running from ROM on bank 0, we can NOT - * execute the code that modifies bank 0 timings from ROM, so - * we run it from cache. - * - * Notes: Does NOT use the stack. - *****************************************************************************/ - .section ".text" - .align 2 - .globl ext_bus_cntlr_init - .type ext_bus_cntlr_init, @function -ext_bus_cntlr_init: - mflr r0 - /******************************************************************** - * Prefetch entire ext_bus_cntrl_init function into the icache. - * This is necessary because we are going to change the same CS we - * are executing from. Otherwise a CPU lockup may occur. - *******************************************************************/ - bl ..getAddr -..getAddr: - mflr r3 /* get address of ..getAddr */ - - /* Calculate number of cache lines for this function */ - addi r4, 0, (((.Lfe0 - ..getAddr) / CONFIG_SYS_CACHELINE_SIZE) + 2) - mtctr r4 -..ebcloop: - icbt r0, r3 /* prefetch cache line for addr in r3*/ - addi r3, r3, CONFIG_SYS_CACHELINE_SIZE /* move to next cache line */ - bdnz ..ebcloop /* continue for $CTR cache lines */ - - /******************************************************************** - * Delay to ensure all accesses to ROM are complete before changing - * bank 0 timings. 200usec should be enough. - * 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles. - *******************************************************************/ - addis r3, 0, 0x0 - ori r3, r3, 0xA000 /* wait 200us from reset */ - mtctr r3 -..spinlp: - bdnz ..spinlp /* spin loop */ - - /******************************************************************** - * Setup External Bus Controller (EBC). - *******************************************************************/ - addi r3, 0, EBC0_CFG - mtdcr EBC0_CFGADDR, r3 - addis r4, 0, 0xb040 /* Device base timeout = 1024 cycles */ - ori r4, r4, 0x0 /* Drive CS with external master */ - mtdcr EBC0_CFGDATA, r4 - - /******************************************************************** - * Change PCIINT signal to PerWE - *******************************************************************/ - mfdcr r4, CPC0_CR1 - ori r4, r4, 0x4000 - mtdcr CPC0_CR1, r4 - - /******************************************************************** - * Memory Bank 0 (Flash Bank 0) initialization - *******************************************************************/ - addi r3, 0, PB1AP - mtdcr EBC0_CFGADDR, r3 - addis r4, 0, CONFIG_SYS_W7O_EBC_PB0AP@h - ori r4, r4, CONFIG_SYS_W7O_EBC_PB0AP@l - mtdcr EBC0_CFGDATA, r4 - - addi r3, 0, PB0CR - mtdcr EBC0_CFGADDR, r3 - addis r4, 0, CONFIG_SYS_W7O_EBC_PB0CR@h - ori r4, r4, CONFIG_SYS_W7O_EBC_PB0CR@l - mtdcr EBC0_CFGDATA, r4 - - /******************************************************************** - * Memory Bank 7 LEDs - NEEDED BECAUSE OF HW WATCHDOG AND LEDs. - *******************************************************************/ - addi r3, 0, PB7AP - mtdcr EBC0_CFGADDR, r3 - addis r4, 0, CONFIG_SYS_W7O_EBC_PB7AP@h - ori r4, r4, CONFIG_SYS_W7O_EBC_PB7AP@l - mtdcr EBC0_CFGDATA, r4 - - addi r3, 0, PB7CR - mtdcr EBC0_CFGADDR, r3 - addis r4, 0, CONFIG_SYS_W7O_EBC_PB7CR@h - ori r4, r4, CONFIG_SYS_W7O_EBC_PB7CR@l - mtdcr EBC0_CFGDATA, r4 - - /* We are all done */ - mtlr r0 /* Restore link register */ - blr /* Return to calling function */ -.Lfe0: .size ext_bus_cntlr_init,.Lfe0-ext_bus_cntlr_init -/* end ext_bus_cntlr_init() */ - -/****************************************************************************** - * Function: sdram_init - * - * Description: Configures SDRAM memory banks. - * - * Serial Presence Detect, "SPD," reads the SDRAM EEPROM - * via the IIC bus and then configures the SDRAM memory - * banks appropriately. If Auto Memory Configuration is - * is not used, it is assumed that a 4MB 11x8x2, non-ECC, - * SDRAM is soldered down. - * - * Notes: Expects that the stack is already setup. - *****************************************************************************/ - .section ".text" - .align 2 - .globl sdram_init - .type sdram_init, @function -sdram_init: - /* save the return info on stack */ - mflr r0 /* Get link register */ - stwu r1, -8(r1) /* Save back chain and move SP */ - stw r0, +12(r1) /* Save link register */ - - /* - * First call spd_sdram to try to init SDRAM according to the - * contents of the SPD EEPROM. If the SPD EEPROM is blank or - * erronious, spd_sdram returns 0 in R3. - */ - li r3,0 - bl spd_sdram - addic. r3, r3, 0 /* Check for error, save dram size */ - bne ..sdri_done /* If it worked, we're done... */ - - /******************************************************************** - * If SPD detection fails, we'll default to 4MB, 11x8x2, as this - * is the SMALLEST SDRAM size the 405 supports. We can do this - * because W7O boards have soldered on RAM, and there will always - * be some amount present. If we were using DIMMs, we should hang - * the board instead, since it doesn't have any RAM to continue - * running with. - *******************************************************************/ - - /* - * Disable memory controller to allow - * values to be changed. - */ - addi r3, 0, SDRAM0_CFG - mtdcr SDRAM0_CFGADDR, r3 - addis r4, 0, 0x0 - ori r4, r4, 0x0 - mtdcr SDRAM0_CFGDATA, r4 - - /* - * Set MB0CF for ext bank 0. (0-4MB) Address Mode 5 since 11x8x2 - * All other banks are disabled. - */ - addi r3, 0, SDRAM0_B0CR - mtdcr SDRAM0_CFGADDR, r3 - addis r4, 0, 0x0000 /* BA=0x0, SZ=4MB */ - ori r4, r4, 0x8001 /* Mode is 5, 11x8x2or4, BE=Enabled */ - mtdcr SDRAM0_CFGDATA, r4 - - /* Clear MB1CR,MB2CR,MB3CR to turn other banks off */ - addi r4, 0, 0 /* Zero the data reg */ - - addi r3, r3, 4 /* Point to MB1CF reg */ - mtdcr SDRAM0_CFGADDR, r3 /* Set the address */ - mtdcr SDRAM0_CFGDATA, r4 /* Zero the reg */ - - addi r3, r3, 4 /* Point to MB2CF reg */ - mtdcr SDRAM0_CFGADDR, r3 /* Set the address */ - mtdcr SDRAM0_CFGDATA, r4 /* Zero the reg */ - - addi r3, r3, 4 /* Point to MB3CF reg */ - mtdcr SDRAM0_CFGADDR, r3 /* Set the address */ - mtdcr SDRAM0_CFGDATA, r4 /* Zero the reg */ - - /******************************************************************** - * Set the SDRAM Timing reg, SDTR1 and the refresh timer reg, RTR. - * To set the appropriate timings, we assume sdram is - * 100MHz (pc100 compliant). - *******************************************************************/ - - /* - * Set up SDTR1 - */ - addi r3, 0, SDRAM0_TR - mtdcr SDRAM0_CFGADDR, r3 - addis r4, 0, 0x0086 /* SDTR1 value for 100Mhz */ - ori r4, r4, 0x400D - mtdcr SDRAM0_CFGDATA, r4 - - /* - * Set RTR - */ - addi r3, 0, SDRAM0_RTR - mtdcr SDRAM0_CFGADDR, r3 - addis r4, 0, 0x05F0 /* RTR refresh val = 15.625ms@100Mhz */ - mtdcr SDRAM0_CFGDATA, r4 - - /******************************************************************** - * Delay to ensure 200usec have elapsed since reset. Assume worst - * case that the core is running 200Mhz: - * 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles - *******************************************************************/ - addis r3, 0, 0x0000 - ori r3, r3, 0xA000 /* Wait 200us from reset */ - mtctr r3 -..spinlp2: - bdnz ..spinlp2 /* spin loop */ - - /******************************************************************** - * Set memory controller options reg, MCOPT1. - *******************************************************************/ - addi r3, 0, SDRAM0_CFG - mtdcr SDRAM0_CFGADDR, r3 - addis r4, 0, 0x80E0 /* DC_EN=1,SRE=0,PME=0,MEMCHK=0 */ - ori r4, r4, 0x0000 /* REGEN=0,DRW=00,BRPF=01,ECCDD=1 */ - mtdcr SDRAM0_CFGDATA, r4 /* EMDULR=1 */ - -..sdri_done: - /* restore and return */ - lwz r0, +12(r1) /* Get saved link register */ - addi r1, r1, +8 /* Remove frame from stack */ - mtlr r0 /* Restore link register */ - blr /* Return to calling function */ -.Lfe1: .size sdram_init,.Lfe1-sdram_init -/* end sdram_init() */ |