diff options
Diffstat (limited to 'board/ti')
-rw-r--r-- | board/ti/omap5912osk/Kconfig | 23 | ||||
-rw-r--r-- | board/ti/omap5912osk/MAINTAINERS | 6 | ||||
-rw-r--r-- | board/ti/omap5912osk/Makefile | 9 | ||||
-rw-r--r-- | board/ti/omap5912osk/config.mk | 30 | ||||
-rw-r--r-- | board/ti/omap5912osk/lowlevel_init.S | 477 | ||||
-rw-r--r-- | board/ti/omap5912osk/omap5912osk.c | 307 |
6 files changed, 0 insertions, 852 deletions
diff --git a/board/ti/omap5912osk/Kconfig b/board/ti/omap5912osk/Kconfig deleted file mode 100644 index 9f7493a35fb..00000000000 --- a/board/ti/omap5912osk/Kconfig +++ /dev/null @@ -1,23 +0,0 @@ -if TARGET_OMAP5912OSK - -config SYS_CPU - string - default "arm926ejs" - -config SYS_BOARD - string - default "omap5912osk" - -config SYS_VENDOR - string - default "ti" - -config SYS_SOC - string - default "omap" - -config SYS_CONFIG_NAME - string - default "omap5912osk" - -endif diff --git a/board/ti/omap5912osk/MAINTAINERS b/board/ti/omap5912osk/MAINTAINERS deleted file mode 100644 index 43ffb9b7b9e..00000000000 --- a/board/ti/omap5912osk/MAINTAINERS +++ /dev/null @@ -1,6 +0,0 @@ -OMAP5912OSK BOARD -M: Rishi Bhattacharya <rishi@ti.com> -S: Maintained -F: board/ti/omap5912osk/ -F: include/configs/omap5912osk.h -F: configs/omap5912osk_defconfig diff --git a/board/ti/omap5912osk/Makefile b/board/ti/omap5912osk/Makefile deleted file mode 100644 index d7c0ebd729d..00000000000 --- a/board/ti/omap5912osk/Makefile +++ /dev/null @@ -1,9 +0,0 @@ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y := omap5912osk.o -obj-y += lowlevel_init.o diff --git a/board/ti/omap5912osk/config.mk b/board/ti/omap5912osk/config.mk deleted file mode 100644 index 5b8d952ba6d..00000000000 --- a/board/ti/omap5912osk/config.mk +++ /dev/null @@ -1,30 +0,0 @@ -# -# (C) Copyright 2002-2004 -# Gary Jennejohn, DENX Software Engineering, <garyj@denx.de> -# David Mueller, ELSOFT AG, <d.mueller@elsoft.ch> -# -# (C) Copyright 2003 -# Texas Instruments, <www.ti.com> -# Kshitij Gupta <Kshitij@ti.com> -# -# (C) Copyright 2004 -# Texas Instruments, <www.ti.com> -# Rishi Bhattacharya <rishi@ti.com> -# -# TI OSK board with OMAP5912 (ARM925EJS) cpu -# see http://www.ti.com/ for more information on Texas Instruments -# -# OSK has 1 bank of 32 MB SDRAM -# Physical Address: -# 1000'0000 to 1200'0000 -# -# -# Linux-Kernel is expected to be at 1000'8000, entry 1000'8000 -# (mem base + reserved) -# -# When running from RAM use address 1108'0000, otherwise when -# booting from NOR flash link to address 0000'0000. -# - -CONFIG_SYS_TEXT_BASE = 0x00000000 -#CONFIG_SYS_TEXT_BASE = 0x11080000 diff --git a/board/ti/omap5912osk/lowlevel_init.S b/board/ti/omap5912osk/lowlevel_init.S deleted file mode 100644 index e05a1c7b557..00000000000 --- a/board/ti/omap5912osk/lowlevel_init.S +++ /dev/null @@ -1,477 +0,0 @@ -/* - * Board specific setup info - * - * (C) Copyright 2003 - * Texas Instruments, <www.ti.com> - * Kshitij Gupta <Kshitij@ti.com> - * - * Modified for OMAP 1610 H2 board by Nishant Kamat, Jan 2004 - * - * Modified for OMAP 5912 OSK board by Rishi Bhattacharya, Apr 2004 - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <config.h> -#include <version.h> - -#if defined(CONFIG_OMAP1610) -#include <./configs/omap1510.h> -#endif - -.globl lowlevel_init -lowlevel_init: - - /*------------------------------------------------------* - * Ensure i-cache is enabled * - * To configure TC regs without fetching instruction * - *------------------------------------------------------*/ - mrc p15, 0, r0, c1, c0 - orr r0, r0, #0x1000 - mcr p15, 0, r0, c1, c0 - - /*------------------------------------------------------* - *mask all IRQs by setting all bits in the INTMR default* - *------------------------------------------------------*/ - mov r1, #0xffffffff - ldr r0, =REG_IHL1_MIR - str r1, [r0] - ldr r0, =REG_IHL2_MIR - str r1, [r0] - - /*------------------------------------------------------* - * Set up ARM CLM registers (IDLECT1) * - *------------------------------------------------------*/ - ldr r0, REG_ARM_IDLECT1 - ldr r1, VAL_ARM_IDLECT1 - str r1, [r0] - - /*------------------------------------------------------* - * Set up ARM CLM registers (IDLECT2) * - *------------------------------------------------------*/ - ldr r0, REG_ARM_IDLECT2 - ldr r1, VAL_ARM_IDLECT2 - str r1, [r0] - - /*------------------------------------------------------* - * Set up ARM CLM registers (IDLECT3) * - *------------------------------------------------------*/ - ldr r0, REG_ARM_IDLECT3 - ldr r1, VAL_ARM_IDLECT3 - str r1, [r0] - - mov r1, #0x01 /* PER_EN bit */ - ldr r0, REG_ARM_RSTCT2 - strh r1, [r0] /* CLKM; Peripheral reset. */ - - /* Set CLKM to Sync-Scalable */ - mov r1, #0x1000 - ldr r0, REG_ARM_SYSST - - mov r2, #0 -1: cmp r2, #1 - streqh r1, [r0] - add r2, r2, #1 - cmp r2, #0x100 /* wait for any bubbles to finish */ - bne 1b - - ldr r1, VAL_ARM_CKCTL - ldr r0, REG_ARM_CKCTL - strh r1, [r0] - - /* a few nops to let settle */ - nop - nop - nop - nop - nop - nop - nop - nop - nop - nop - - /* setup DPLL 1 */ - /* Ramp up the clock to 96Mhz */ - ldr r1, VAL_DPLL1_CTL - ldr r0, REG_DPLL1_CTL - strh r1, [r0] - ands r1, r1, #0x10 /* Check if PLL is enabled. */ - beq lock_end /* Do not look for lock if BYPASS selected */ -2: - ldrh r1, [r0] - ands r1, r1, #0x01 /* Check the LOCK bit.*/ - beq 2b /* loop until bit goes hi. */ -lock_end: - - /*------------------------------------------------------* - * Turn off the watchdog during init... * - *------------------------------------------------------*/ - ldr r0, REG_WATCHDOG - ldr r1, WATCHDOG_VAL1 - str r1, [r0] - ldr r1, WATCHDOG_VAL2 - str r1, [r0] - ldr r0, REG_WSPRDOG - ldr r1, WSPRDOG_VAL1 - str r1, [r0] - ldr r0, REG_WWPSDOG - -watch1Wait: - ldr r1, [r0] - tst r1, #0x10 - bne watch1Wait - - ldr r0, REG_WSPRDOG - ldr r1, WSPRDOG_VAL2 - str r1, [r0] - ldr r0, REG_WWPSDOG -watch2Wait: - ldr r1, [r0] - tst r1, #0x10 - bne watch2Wait - - /* Set memory timings corresponding to the new clock speed */ - ldr r3, VAL_SDRAM_CONFIG_SDF0 - - /* Check execution location to determine current execution location - * and branch to appropriate initialization code. - */ - mov r0, #0x10000000 /* Load physical SDRAM base. */ - mov r1, pc /* Get current execution location. */ - cmp r1, r0 /* Compare. */ - bge skip_sdram /* Skip over EMIF-fast initialization if running from SDRAM. */ - - /* identify the device revision, -- TMX or TMP(TMS) */ - ldr r0, REG_DEVICE_ID - ldr r1, [r0] - - ldr r0, VAL_DEVICE_ID_TMP - mov r1, r1, lsl #15 - mov r1, r1, lsr #16 - cmp r0, r1 - bne skip_TMP_Patch - - /* Enable TMP/TMS device new features */ - mov r0, #1 - ldr r1, REG_TC_EMIFF_DOUBLER - str r0, [r1] - - /* Enable new ac parameters */ - mov r0, #0x0b - ldr r1, REG_SDRAM_CONFIG2 - str r0, [r1] - - ldr r3, VAL_SDRAM_CONFIG_SDF1 - -skip_TMP_Patch: - - /* - * Delay for SDRAM initialization. - */ - mov r0, #0x1800 /* value should be checked */ -3: - subs r0, r0, #0x1 /* Decrement count */ - bne 3b - - /* - * Set SDRAM control values. Disable refresh before MRS command. - */ - - /* mobile ddr operation */ - ldr r0, REG_SDRAM_OPERATION - mov r2, #07 - str r2, [r0] - - /* config register */ - ldr r0, REG_SDRAM_CONFIG - str r3, [r0] - - /* manual command register */ - ldr r0, REG_SDRAM_MANUAL_CMD - - /* issue set cke high */ - mov r1, #CMD_SDRAM_CKE_SET_HIGH - str r1, [r0] - - /* issue nop */ - mov r1, #CMD_SDRAM_NOP - str r1, [r0] - - mov r2, #0x0100 -waitMDDR1: - subs r2, r2, #1 - bne waitMDDR1 /* delay loop */ - - /* issue precharge */ - mov r1, #CMD_SDRAM_PRECHARGE - str r1, [r0] - - /* issue autorefresh x 2 */ - mov r1, #CMD_SDRAM_AUTOREFRESH - str r1, [r0] - str r1, [r0] - - /* mrs register ddr mobile */ - ldr r0, REG_SDRAM_MRS - mov r1, #0x33 - str r1, [r0] - - /* emrs1 low-power register */ - ldr r0, REG_SDRAM_EMRS1 - /* self refresh on all banks */ - mov r1, #0 - str r1, [r0] - - ldr r0, REG_DLL_URD_CONTROL - ldr r1, DLL_URD_CONTROL_VAL - str r1, [r0] - - ldr r0, REG_DLL_LRD_CONTROL - ldr r1, DLL_LRD_CONTROL_VAL - str r1, [r0] - - ldr r0, REG_DLL_WRT_CONTROL - ldr r1, DLL_WRT_CONTROL_VAL - str r1, [r0] - - /* delay loop */ - mov r0, #0x0100 -waitMDDR2: - subs r0, r0, #1 - bne waitMDDR2 - - /* - * Delay for SDRAM initialization. - */ - mov r0, #0x1800 -4: - subs r0, r0, #1 /* Decrement count. */ - bne 4b - b common_tc - -skip_sdram: - ldr r0, REG_SDRAM_CONFIG - str r3, [r0] - -common_tc: - /* slow interface */ - ldr r1, VAL_TC_EMIFS_CS0_CONFIG - ldr r0, REG_TC_EMIFS_CS0_CONFIG - str r1, [r0] /* Chip Select 0 */ - - ldr r1, VAL_TC_EMIFS_CS1_CONFIG - ldr r0, REG_TC_EMIFS_CS1_CONFIG - str r1, [r0] /* Chip Select 1 */ - - ldr r1, VAL_TC_EMIFS_CS3_CONFIG - ldr r0, REG_TC_EMIFS_CS3_CONFIG - str r1, [r0] /* Chip Select 3 */ - - ldr r1, VAL_TC_EMIFS_DWS - ldr r0, REG_TC_EMIFS_DWS - str r1, [r0] /* Enable EMIFS.RDY for CS1 (ether) */ - -#ifdef CONFIG_H2_OMAP1610 - /* inserting additional 2 clock cycle hold time for LAN */ - ldr r0, REG_TC_EMIFS_CS1_ADVANCED - ldr r1, VAL_TC_EMIFS_CS1_ADVANCED - str r1, [r0] -#endif - /* Start MPU Timer 1 */ - ldr r0, REG_MPU_LOAD_TIMER - ldr r1, VAL_MPU_LOAD_TIMER - str r1, [r0] - - ldr r0, REG_MPU_CNTL_TIMER - ldr r1, VAL_MPU_CNTL_TIMER - str r1, [r0] - - /* - * Setup a temporary stack - */ - ldr sp, SRAM_STACK - bic sp, sp, #7 /* 8-byte alignment for ABI compliance */ - - /* - * Save the old lr(passed in ip) and the current lr to stack - */ - push {ip, lr} - - /* - * go setup pll, mux, memory - */ - bl s_init - pop {ip, pc} - - /* back to arch calling code */ - mov pc, lr - - /* the literal pools origin */ - .ltorg - -REG_DEVICE_ID: /* 32 bits */ - .word 0xfffe2004 -REG_TC_EMIFS_CONFIG: - .word 0xfffecc0c -REG_TC_EMIFS_CS0_CONFIG: /* 32 bits */ - .word 0xfffecc10 -REG_TC_EMIFS_CS1_CONFIG: /* 32 bits */ - .word 0xfffecc14 -REG_TC_EMIFS_CS2_CONFIG: /* 32 bits */ - .word 0xfffecc18 -REG_TC_EMIFS_CS3_CONFIG: /* 32 bits */ - .word 0xfffecc1c -REG_TC_EMIFS_DWS: /* 32 bits */ - .word 0xfffecc40 -#ifdef CONFIG_H2_OMAP1610 -REG_TC_EMIFS_CS1_ADVANCED: /* 32 bits */ - .word 0xfffecc54 -#endif - -/* MPU clock/reset/power mode control registers */ -REG_ARM_CKCTL: /* 16 bits */ - .word 0xfffece00 -REG_ARM_IDLECT3: /* 16 bits */ - .word 0xfffece24 -REG_ARM_IDLECT2: /* 16 bits */ - .word 0xfffece08 -REG_ARM_IDLECT1: /* 16 bits */ - .word 0xfffece04 -REG_ARM_RSTCT2: /* 16 bits */ - .word 0xfffece14 -REG_ARM_SYSST: /* 16 bits */ - .word 0xfffece18 - -/* DPLL control registers */ -REG_DPLL1_CTL: /* 16 bits */ - .word 0xfffecf00 - -/* Watch Dog register */ -/* secure watchdog stop */ -REG_WSPRDOG: - .word 0xfffeb048 -/* watchdog write pending */ -REG_WWPSDOG: - .word 0xfffeb034 - -WSPRDOG_VAL1: - .word 0x0000aaaa -WSPRDOG_VAL2: - .word 0x00005555 - -/* SDRAM config is: auto refresh enabled, 16 bit 4 bank, - counter @8192 rows, 10 ns, 8 burst */ -REG_SDRAM_CONFIG: - .word 0xfffecc20 -REG_SDRAM_CONFIG2: - .word 0xfffecc3c -REG_TC_EMIFF_DOUBLER: /* 32 bits */ - .word 0xfffecc60 - -/* Operation register */ -REG_SDRAM_OPERATION: - .word 0xfffecc80 - -/* Manual command register */ -REG_SDRAM_MANUAL_CMD: - .word 0xfffecc84 - -/* SDRAM MRS (New) config is: CAS latency is 2, burst length 8 */ -REG_SDRAM_MRS: - .word 0xfffecc70 - -/* SDRAM MRS (New) config is: CAS latency is 2, burst length 8 */ -REG_SDRAM_EMRS1: - .word 0xfffecc78 - -/* WRT DLL register */ -REG_DLL_WRT_CONTROL: - .word 0xfffecc68 -DLL_WRT_CONTROL_VAL: - .word 0x03f00002 /* Phase of 72deg, write offset +31 */ - -/* URD DLL register */ -REG_DLL_URD_CONTROL: - .word 0xfffeccc0 -DLL_URD_CONTROL_VAL: - .word 0x00800002 /* Phase of 72deg, read offset +31 */ - -/* LRD DLL register */ -REG_DLL_LRD_CONTROL: - .word 0xfffecccc -DLL_LRD_CONTROL_VAL: - .word 0x00800002 /* read offset +31 */ - -REG_WATCHDOG: - .word 0xfffec808 -WATCHDOG_VAL1: - .word 0x000000f5 -WATCHDOG_VAL2: - .word 0x000000a0 - -REG_MPU_LOAD_TIMER: - .word 0xfffec504 -REG_MPU_CNTL_TIMER: - .word 0xfffec500 -VAL_MPU_LOAD_TIMER: - .word 0xffffffff -VAL_MPU_CNTL_TIMER: - .word 0xffffffa1 - -/* 96 MHz Samsung Mobile DDR */ -/* Original setting for TMX device */ -VAL_SDRAM_CONFIG_SDF0: - .word 0x0014e6fe - -/* NEW_SYS_FREQ mode (valid only TMP/TMS devices) */ -VAL_SDRAM_CONFIG_SDF1: - .word 0x0114e6fe - -VAL_ARM_CKCTL: - .word 0x2000 /* was: 0x3000, now use CLK_REF for timer input */ -VAL_DPLL1_CTL: - .word 0x2830 - -#ifdef CONFIG_OSK_OMAP5912 -VAL_TC_EMIFS_CS0_CONFIG: - .word 0x002130b0 -VAL_TC_EMIFS_CS1_CONFIG: - .word 0x00001133 -VAL_TC_EMIFS_CS2_CONFIG: - .word 0x000055f0 -VAL_TC_EMIFS_CS3_CONFIG: - .word 0x88013141 -VAL_TC_EMIFS_DWS: /* Enable EMIFS.RDY for CS1 access (ether) */ - .word 0x000000c0 -VAL_DEVICE_ID_TMP: /* TMP/TMS=0xb65f, TMX=0xb58c */ - .word 0xb65f -#endif - -#ifdef CONFIG_H2_OMAP1610 -VAL_TC_EMIFS_CS0_CONFIG: - .word 0x00203331 -VAL_TC_EMIFS_CS1_CONFIG: - .word 0x8180fff3 -VAL_TC_EMIFS_CS2_CONFIG: - .word 0xf800f22a -VAL_TC_EMIFS_CS3_CONFIG: - .word 0x88013141 -VAL_TC_EMIFS_CS1_ADVANCED: - .word 0x00000022 -#endif - -VAL_ARM_IDLECT1: - .word 0x00000400 -VAL_ARM_IDLECT2: - .word 0x00000886 -VAL_ARM_IDLECT3: - .word 0x00000015 - -SRAM_STACK: - .word CONFIG_SYS_INIT_SP_ADDR - -/* command values */ -.equ CMD_SDRAM_NOP, 0x00000000 -.equ CMD_SDRAM_PRECHARGE, 0x00000001 -.equ CMD_SDRAM_AUTOREFRESH, 0x00000002 -.equ CMD_SDRAM_CKE_SET_HIGH, 0x00000007 diff --git a/board/ti/omap5912osk/omap5912osk.c b/board/ti/omap5912osk/omap5912osk.c deleted file mode 100644 index 88a7310cec6..00000000000 --- a/board/ti/omap5912osk/omap5912osk.c +++ /dev/null @@ -1,307 +0,0 @@ -/* - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH <www.elinos.com> - * Marius Groeger <mgroeger@sysgo.de> - * - * (C) Copyright 2002 - * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch> - * - * (C) Copyright 2003 - * Texas Instruments, <www.ti.com> - * Kshitij Gupta <Kshitij@ti.com> - * - * (C) Copyright 2004 - * Texas Instruments, <www.ti.com> - * Rishi Bhattacharya <rishi@ti.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <netdev.h> -#if defined(CONFIG_OMAP1610) -#include <./configs/omap1510.h> -#endif - -DECLARE_GLOBAL_DATA_PTR; - -void flash__init (void); -void ether__init (void); -void set_muxconf_regs (void); -void peripheral_power_enable (void); - -#define COMP_MODE_ENABLE ((unsigned int)0x0000EAEF) - -static inline void delay (unsigned long loops) -{ - __asm__ volatile ("1:\n" - "subs %0, %1, #1\n" - "bne 1b":"=r" (loops):"0" (loops)); -} - -/* - * Miscellaneous platform dependent initialisations - */ - -int board_init (void) -{ - gd->bd->bi_arch_number = MACH_TYPE_OMAP_OSK; - - /* adress of boot parameters */ - gd->bd->bi_boot_params = 0x10000100; - - flash__init(); - ether__init(); - - return 0; -} - -void s_init(void) -{ - /* Configure MUX settings */ - set_muxconf_regs (); - peripheral_power_enable (); - -/* this speeds up your boot a quite a bit. However to make it - * work, you need make sure your kernel startup flush bug is fixed. - * ... rkw ... - */ - icache_enable (); -} - -/****************************** - Routine: - Description: -******************************/ -void flash__init (void) -{ -#define EMIFS_GlB_Config_REG 0xfffecc0c - unsigned int regval; - regval = *((volatile unsigned int *) EMIFS_GlB_Config_REG); - /* Turn off write protection for flash devices. */ - regval = regval | 0x0001; - *((volatile unsigned int *) EMIFS_GlB_Config_REG) = regval; -} -/************************************************************* - Routine:ether__init - Description: take the Ethernet controller out of reset and wait - for the EEPROM load to complete. -*************************************************************/ -void ether__init (void) -{ -#define ETH_CONTROL_REG 0x0480000b - int i; - - *((volatile unsigned short *) 0xfffece08) = 0x03FF; - *((volatile unsigned short *) 0xfffb3824) = 0x8000; - *((volatile unsigned short *) 0xfffb3830) = 0x0000; - *((volatile unsigned short *) 0xfffb3834) = 0x0009; - *((volatile unsigned short *) 0xfffb3838) = 0x0009; - *((volatile unsigned short *) 0xfffb3818) = 0x0002; - *((volatile unsigned short *) 0xfffb382C) = 0x0048; - *((volatile unsigned short *) 0xfffb3824) = 0x8603; - udelay (3); - for (i=0;i<2000;i++); - *((volatile unsigned short *) 0xfffb381C) = 0x6610; - udelay (30); - for (i=0;i<10000;i++); - - *((volatile unsigned char *) ETH_CONTROL_REG) &= ~0x01; - udelay (3); - - -} - -/****************************** - Routine: - Description: -******************************/ -int dram_init(void) -{ - gd->ram_size = get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE); - - return 0; -} - -void dram_init_banksize(void) -{ - gd->bd->bi_dram[0].start = PHYS_SDRAM_1; - gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE; -} - -/****************************************************** - Routine: set_muxconf_regs - Description: Setting up the configuration Mux registers - specific to the hardware -*******************************************************/ -void set_muxconf_regs (void) -{ - volatile unsigned int *MuxConfReg; - /* set each registers to its reset value; */ - MuxConfReg = - (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_0); - /* setup for UART1 */ - *MuxConfReg &= ~(0x02000000); /* bit 25 */ - /* setup for UART2 */ - *MuxConfReg &= ~(0x01000000); /* bit 24 */ - /* Disable Uwire CS Hi-Z */ - *MuxConfReg |= 0x08000000; - MuxConfReg = - (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_3); - *MuxConfReg = 0x00000000; - MuxConfReg = - (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_4); - *MuxConfReg = 0x00000000; - MuxConfReg = - (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_5); - *MuxConfReg = 0x00000000; - MuxConfReg = - (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_6); - /*setup mux for UART3 */ - *MuxConfReg |= 0x00000001; /* bit3, 1, 0 (mux0 5,5,26) */ - *MuxConfReg &= ~0x0000003e; - MuxConfReg = - (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_7); - *MuxConfReg = 0x00000000; - MuxConfReg = - (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_8); - /* Disable Uwire CS Hi-Z */ - *MuxConfReg |= 0x00001200; /*bit 9 for CS0 12 for CS3 */ - MuxConfReg = - (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_9); - /* Need to turn on bits 21 and 12 in FUNC_MUX_CTRL_9 so the */ - /* hardware will actually use TX and RTS based on bit 25 in */ - /* FUNC_MUX_CTRL_0. I told you this thing was screwy! */ - *MuxConfReg |= 0x00201000; - MuxConfReg = - (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_A); - *MuxConfReg = 0x00000000; - MuxConfReg = - (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_B); - *MuxConfReg = 0x00000000; - MuxConfReg = - (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_C); - /* setup for UART2 */ - /* Need to turn on bits 27 and 24 in FUNC_MUX_CTRL_C so the */ - /* hardware will actually use TX and RTS based on bit 24 in */ - /* FUNC_MUX_CTRL_0. */ - *MuxConfReg |= 0x09000000; - MuxConfReg = - (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_D); - *MuxConfReg |= 0x00000020; - MuxConfReg = - (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_0); - *MuxConfReg = 0x00000000; - MuxConfReg = - (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_1); - *MuxConfReg = 0x00000000; - /* mux setup for SD/MMC driver */ - MuxConfReg = - (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_2); - *MuxConfReg &= 0xFFFE0FFF; - MuxConfReg = - (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_3); - *MuxConfReg = 0x00000000; - MuxConfReg = - (volatile unsigned int *) ((unsigned int) MOD_CONF_CTRL_0); - /* bit 13 for MMC2 XOR_CLK */ - *MuxConfReg &= ~(0x00002000); - /* bit 29 for UART 1 */ - *MuxConfReg &= ~(0x00002000); - MuxConfReg = - (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_0); - /* Configure for USB. Turn on VBUS_CTRL and VBUS_MODE. */ - *MuxConfReg |= 0x000C0000; - MuxConfReg = - (volatile unsigned int *) ((unsigned int)USB_TRANSCEIVER_CTRL); - *MuxConfReg &= ~(0x00000070); - *MuxConfReg &= ~(0x00000008); - *MuxConfReg |= 0x00000003; - *MuxConfReg |= 0x00000180; - MuxConfReg = - (volatile unsigned int *) ((unsigned int) MOD_CONF_CTRL_0); - /* bit 17, software controls VBUS */ - *MuxConfReg &= ~(0x00020000); - /* Enable USB 48 and 12M clocks */ - *MuxConfReg |= 0x00000200; - *MuxConfReg &= ~(0x00000180); - /*2.75V for MMCSDIO1 */ - MuxConfReg = - (volatile unsigned int *) ((unsigned int) VOLTAGE_CTRL_0); - *MuxConfReg = 0x00001FE7; - MuxConfReg = - (volatile unsigned int *) ((unsigned int) PU_PD_SEL_0); - *MuxConfReg = 0x00000000; - MuxConfReg = - (volatile unsigned int *) ((unsigned int) PU_PD_SEL_1); - *MuxConfReg = 0x00000000; - MuxConfReg = - (volatile unsigned int *) ((unsigned int) PU_PD_SEL_2); - *MuxConfReg = 0x00000000; - MuxConfReg = - (volatile unsigned int *) ((unsigned int) PU_PD_SEL_3); - *MuxConfReg = 0x00000000; - MuxConfReg = - (volatile unsigned int *) ((unsigned int) PU_PD_SEL_4); - *MuxConfReg = 0x00000000; - MuxConfReg = - (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_4); - *MuxConfReg = 0x00000000; - /* Turn on UART2 48 MHZ clock */ - MuxConfReg = - (volatile unsigned int *) ((unsigned int) MOD_CONF_CTRL_0); - *MuxConfReg |= 0x40000000; - MuxConfReg = - (volatile unsigned int *) ((unsigned int) USB_OTG_CTRL); - /* setup for USB VBus detection OMAP161x */ - *MuxConfReg |= 0x00040000; /* bit 18 */ - MuxConfReg = - (volatile unsigned int *) ((unsigned int) PU_PD_SEL_2); - /* PullUps for SD/MMC driver */ - *MuxConfReg |= ~(0xFFFE0FFF); - MuxConfReg = - (volatile unsigned int *) ((unsigned int)COMP_MODE_CTRL_0); - *MuxConfReg = COMP_MODE_ENABLE; -} - -/****************************************************** - Routine: peripheral_power_enable - Description: Enable the power for UART1 -*******************************************************/ -void peripheral_power_enable (void) -{ -#define UART1_48MHZ_ENABLE ((unsigned short)0x0200) -#define SW_CLOCK_REQUEST ((volatile unsigned short *)0xFFFE0834) - - *SW_CLOCK_REQUEST |= UART1_48MHZ_ENABLE; -} - -/* - * Check Board Identity - */ -int checkboard(void) -{ - char buf[64]; - int i = getenv_f("serial#", buf, sizeof(buf)); - - puts("Board: OSK5912"); - - if (i > 0) { - puts(", serial# "); - puts(buf); - } - putc('\n'); - - return (0); -} - -#ifdef CONFIG_CMD_NET -int board_eth_init(bd_t *bis) -{ - int rc = 0; -#ifdef CONFIG_LAN91C96 - rc = lan91c96_initialize(0, CONFIG_LAN91C96_BASE); -#endif - return rc; -} -#endif |