diff options
Diffstat (limited to 'board/st/nhk8815/platform.S')
-rw-r--r-- | board/st/nhk8815/platform.S | 340 |
1 files changed, 0 insertions, 340 deletions
diff --git a/board/st/nhk8815/platform.S b/board/st/nhk8815/platform.S deleted file mode 100644 index 2a671102312..00000000000 --- a/board/st/nhk8815/platform.S +++ /dev/null @@ -1,340 +0,0 @@ -/* - * Board specific setup info - * - * (C) Copyright 2005 - * STMicrolelctronics, <www.st.com> - * - * (C) Copyright 2004, ARM Ltd. - * Philippe Robin, <philippe.robin@arm.com> - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#include <config.h> -#include <version.h> - -.globl lowlevel_init -lowlevel_init: - /* Jump to the flash address */ - ldr r0, =CFG_ONENAND_BASE - - /* - * Make it independent whether we boot from 0x0 or 0x30000000. - * Non-portable: it relies on the knowledge that ip has to be updated - */ - orr ip, ip, r0 /* adjust return address of cpu_init_crit */ - orr lr, lr, r0 /* adjust return address */ - orr pc, pc, r0 /* jump to the normal address */ - nop - - /* Initialize PLL, Remap clear, FSMC, MPMC here! */ - /* What about GPIO, CLCD and UART */ - - /* PLL Initialization */ - /* Prog the PLL1 @ 266 MHz ==> SDRAM Clock = 100.8 MHz */ - ldr r0, =NOMADIK_SRC_BASE - - ldr r1, =0x2B013502 - - str r1, [r0, #0x14] - - /* Used to set all the timers clock to 2.4MHZ */ - ldr r1, =0x2AAAA004 - str r1, [r0] - - ldr r1, =0x10000000 - str r1, [r0, #0x10] - - /* FSMC setup ---- */ - ldr r0, =NOMADIK_FSMC_BASE - - ldr r1, =0x10DB /* For 16-bit NOR flash */ - str r1, [r0, #0x08] - - ldr r1, =0x03333333 /* For 16-bit NOR flash */ - str r1, [r0, #0xc] - - /* oneNAND setting */ - ldr r1, =0x0000105B /* BCR0 Prog control register */ - str r1, [r0] - - ldr r1, =0x0A200551 /* BTR0 Prog timing register */ - str r1, [r0, #0x04] - - /* preload the instructions into icache */ - add r0, pc, #0x1F - bic r0, r0, #0x1F - mcr p15, 0, r0, c7, c13, 1 - add r0, r0, #0x20 - mcr p15, 0, r0, c7, c13, 1 - - /* Now Clear Remap */ - ldr r0, =NOMADIK_SRC_BASE - - ldr r1, =0x2004 - str r1, [r0] - - ldr r1, =0x10000000 - str r1, [r0, #0x10] - - ldr r0, =0x101E9000 - ldr r1, =0x2004 - str r1, [r0] - - ldr r0, =NOMADIK_SRC_BASE - ldr r1, =0x2104 - str r1, [r0] - - /* FSMC setup -- */ - mov r0, #(NOMADIK_FSMC_BASE & 0x10000000) - orr r0, r0, #(NOMADIK_FSMC_BASE & 0x0FFFFFFF) - - ldr r1, =0x10DB /* For 16-bit NOR flash */ - str r1, [r0, #0x8] - - ldr r1, =0x03333333 /* For 16-bit NOR flash */ - str r1, [r0, #0xc] - - /* MPMC Setup */ - ldr r0, =NOMADIK_MPMC_BASE - - ldr r1, =0xF00003 - str r1, [r0] /* Enable the MPMC and the DLL */ - - ldr r1, =0x183 - str r1, [r0, #0x20] - - ldr r2, =NOMADIK_PMU_BASE - - ldr r1, =0x1111 - str r1, [r2] - - ldr r1, =0x1111 /* Prog the, mand delay strategy */ - str r1, [r0, #0x28] - - ldr r1, =0x103 /* NOP ,mand */ - str r1, [r0, #0x20] - - /* FIXME -- Wait required here */ - - ldr r1, =0x103 /* PALL ,mand*/ - str r1, [r0, #0x20] - - ldr r1, =0x1 - str r1, [r0, #0x24] /* To do at least two auto-refresh */ - - /* FIXME -- Wait required here */ - - /* Auto-refresh period = 7.8us @ SDRAM Clock = 100.8 MHz */ - ldr r1, =0x31 - str r1, [r0, #0x24] - - /* Prog Little Endian, Not defined in 8800 board */ - ldr r1, =0x0 - str r1, [r0, #0x8] - - - ldr r1, =0x2 - str r1, [r0, #0x30] /* Prog tRP timing */ - - ldr r1, =0x4 /* Change for 8815 */ - str r1, [r0, #0x34] /* Prog tRAS timing */ - - ldr r1, =0xB - str r1, [r0, #0x38] /* Prog tSREX timing */ - - - ldr r1, =0x1 - str r1, [r0, #0x44] /* Prog tWR timing */ - - ldr r1, =0x8 - str r1, [r0, #0x48] /* Prog tRC timing */ - - ldr r1, =0xA - str r1, [r0, #0x4C] /* Prog tRFC timing */ - - ldr r1, =0xB - str r1, [r0, #0x50] /* Prog tXSR timing */ - - ldr r1, =0x1 - str r1, [r0, #0x54] /* Prog tRRD timing */ - - ldr r1, =0x1 - str r1, [r0, #0x58] /* Prog tMRD timing */ - - ldr r1, =0x1 - str r1, [r0, #0x5C] /* Prog tCDLR timing */ - - /* DDR-SDRAM MEMORY IS ON BANK0 8815 */ - ldr r1, =0x304 /* Prog RAS and CAS for CS 0 */ - str r1, [r0, #0x104] - - /* SDR-SDRAM MEMORY IS ON BANK1 8815 */ - ldr r1, =0x304 /* Prog RAS and CAS for CS 1 */ - str r1, [r0, #0x124] - /* THE DATA BUS WIDE IS PROGRAM FOR 16-BITS */ - /* DDR-SDRAM MEMORY IS ON BANK0*/ - - ldr r1, =0x884 /* 8815 : config reg in BRC for CS0 */ - str r1, [r0, #0x100] - - /*SDR-SDRAM MEMORY IS ON BANK1*/ - - ldr r1, =0x884 /* 8815 : config reg in BRC for CS1 */ - str r1, [r0, #0x120] - - ldr r1, =0x83 /*MODE Mand*/ - str r1, [r0, #0x20] - - /* LOAD MODE REGISTER FOR 2 bursts of 16b, with DDR mem ON BANK0 */ - - ldr r1, =0x62000 /*Data in*/ - ldr r1, [r1] - - /* LOAD MODE REGISTER FOR 2 bursts of 16b, with DDR mem ON BANK1 */ - - ldr r1, =0x8062000 - ldr r1, [r1] - - ldr r1, =0x003 - str r1, [r0, #0x20] - - /* ENABLE ALL THE BUFFER FOR EACH AHB PORT*/ - - ldr r1, =0x01 /* Enable buffer 0 */ - str r1, [r0, #0x400] - - ldr r1, =0x01 /* Enable buffer 1 */ - str r1, [r0, #0x420] - - ldr r1, =0x01 /* Enable buffer 2 */ - str r1, [r0, #0x440] - - ldr r1, =0x01 /* Enable buffer 3 */ - str r1, [r0, #0x460] - - ldr r1, =0x01 /* Enable buffer 4 */ - str r1, [r0, #0x480] - - ldr r1, =0x01 /* Enable buffer 5 */ - str r1, [r0, #0x4A0] - - /* GPIO settings */ - - ldr r0, =NOMADIK_GPIO1_BASE - - ldr r1, =0xC0600000 - str r1, [r0, #0x20] - - ldr r1, =0x3F9FFFFF /* ABHI change this for uart1 */ - str r1, [r0, #0x24] - - ldr r1, =0x3F9FFFFF /* ABHI change this for uart1 */ - str r1, [r0, #0x28] - - ldr r0, =NOMADIK_GPIO0_BASE - - ldr r1, =0xFFFFFFFF - str r1, [r0, #0x20] - - ldr r1, =0x00 - str r1, [r0, #0x24] - - ldr r1, =0x00 - str r1, [r0, #0x28] - - /* Configure CPLD_CTRL register for enabling MUX logic for UART0/UART2 */ - - ldr r0, =NOMADIK_FSMC_BASE - - ldr r1, =0x10DB /* INIT FSMC bank 0 */ - str r1, [r0, #0x00] - - ldr r1, =0x0FFFFFFF - str r1, [r0, #0x04] - - ldr r1, =0x010DB /* INIT FSMC bank 1 */ - str r1, [r0, #0x08] - - ldr r1, =0x00FFFFFFF - str r1, [r0, #0x0C] - - ldr r0, =NOMADIK_UART0_BASE - - ldr r1, =0x00000000 - str r1, [r0, #0x30] - - ldr r1, =0x0000004e - str r1, [r0, #0x24] - - ldr r1, =0x00000008 - str r1, [r0, #0x28] - - ldr r1, =0x00000060 - str r1, [r0, #0x2C] - - ldr r1, =0x00000301 - str r1, [r0, #0x30] - - ldr r1, =0x00000066 - str r1, [r0] - - ldr r0, =NOMADIK_UART1_BASE - - ldr r1, =0x00000000 - str r1, [r0, #0x30] - - ldr r1, =0x0000004e - str r1, [r0, #0x24] - - ldr r1, =0x00000008 - str r1, [r0, #0x28] - - ldr r1, =0x00000060 - str r1, [r0, #0x2C] - - ldr r1, =0x00000301 - str r1, [r0, #0x30] - - ldr r1, =0x00000066 - str r1, [r0] - - ldr r0, =NOMADIK_UART2_BASE - - ldr r1, =0x00000000 - str r1, [r0, #0x30] - - ldr r1, =0x0000004e - str r1, [r0, #0x24] - - ldr r1, =0x00000008 - str r1, [r0, #0x28] - - ldr r1, =0x00000060 - str r1, [r0, #0x2C] - - ldr r1, =0x00000301 - str r1, [r0, #0x30] - - ldr r1, =0x00000066 - str r1, [r0] - - /* Configure CPLD to enable UART0 */ - - mov pc, lr |