diff options
Diffstat (limited to 'board/sc3/init.S')
| -rw-r--r-- | board/sc3/init.S | 360 |
1 files changed, 0 insertions, 360 deletions
diff --git a/board/sc3/init.S b/board/sc3/init.S deleted file mode 100644 index 097aa4a5e7..0000000000 --- a/board/sc3/init.S +++ /dev/null @@ -1,360 +0,0 @@ -/* - * SPDX-License-Identifier: GPL-2.0 IBM-pibs - */ -#include <config.h> -#include <asm/ppc4xx.h> - -#include <ppc_asm.tmpl> -#include <ppc_defs.h> - -#include <asm/cache.h> -#include <asm/mmu.h> - -/** - * ext_bus_cntlr_init - Initializes the External Bus Controller for the external peripherals - * - * IMPORTANT: For pass1 this code must run from cache since you can not - * reliably change a peripheral banks timing register (pbxap) while running - * code from that bank. For ex., since we are running from ROM on bank 0, we - * can NOT execute the code that modifies bank 0 timings from ROM, so - * we run it from cache. - * - * Bank 0 - Boot-Flash - * Bank 1 - NAND-Flash - * Bank 2 - ISA bus - * Bank 3 - Second Flash - * Bank 4 - USB controller - */ - .globl ext_bus_cntlr_init -ext_bus_cntlr_init: -/* - * We need the current boot up configuration to set correct - * timings into internal flash and external flash - */ - mfdcr r24,CPC0_PSR /* xxxx xxxx xxxx xxx? ?xxx xxxx xxxx xxxx - 0 0 -> 8 bit external ROM - 0 1 -> 16 bit internal ROM */ - addi r4,0,2 - srw r24,r24,r4 /* shift right r24 two positions */ - andi. r24,r24,0x06000 -/* - * All calculations are based on 33MHz EBC clock. - * - * First, create a "very slow" timing (~250ns) with burst mode enabled - * This is need for the external flash access - */ - lis r25,0x0800 - /* 0000 1000 0xxx 0000 0000 0010 100x xxxx = 0x03800280 */ - ori r25,r25,0x0280 -/* - * Second, create a fast timing: - * 90ns first cycle - 3 clock access - * and 90ns burst cycle, plus 1 clock after the last access - * This is used for the internal access - */ - lis r26,0x8900 - /* 1000 1001 0xxx 0000 0000 0010 100x xxxx */ - ori r26,r26,0x0280 -/* - * We can't change settings on CS# if we currently use them. - * -> load a few instructions into cache and run this code from cache - */ - mflr r4 /* save link register */ - bl ..getAddr -..getAddr: - mflr r3 /* get address of ..getAddr */ - mtlr r4 /* restore link register */ - addi r4,0,14 /* set ctr to 10; used to prefetch */ - mtctr r4 /* 10 cache lines to fit this function - in cache (gives us 8x10=80 instructions) */ -..ebcloop: - icbt r0,r3 /* prefetch cache line for addr in r3 */ - addi r3,r3,32 /* move to next cache line */ - bdnz ..ebcloop /* continue for 10 cache lines */ -/* - * Delay to ensure all accesses to ROM are complete before changing - * bank 0 timings. 200usec should be enough. - * 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles - */ - lis r3,0x0 - ori r3,r3,0xA000 /* ensure 200usec have passed since reset */ - mtctr r3 -..spinlp: - bdnz ..spinlp /* spin loop */ - -/*----------------------------------------------------------------------- - * Memory Bank 0 (BOOT-ROM) initialization - * 0xFFEF00000....0xFFFFFFF - * We only have to change the timing. Mapping is ok by boot-strapping - *----------------------------------------------------------------------- */ - - li r4,PB1AP /* PB0AP=Peripheral Bank 0 Access Parameters */ - mtdcr EBC0_CFGADDR,r4 - - mr r4,r26 /* assume internal fast flash is boot flash */ - cmpwi r24,0x2000 /* assumption true? ... */ - beq 1f /* ...yes! */ - mr r4,r25 /* ...no, use the slow variant */ - mr r25,r26 /* use this for the other flash */ -1: - mtdcr EBC0_CFGDATA,r4 /* change timing now */ - - li r4,PB0CR /* PB0CR=Peripheral Bank 0 Control Register */ - mtdcr EBC0_CFGADDR,r4 - mfdcr r4,EBC0_CFGDATA - lis r3,0x0001 - ori r3,r3,0x8000 /* allow reads and writes */ - or r4,r4,r3 - mtdcr EBC0_CFGDATA,r4 - -/*----------------------------------------------------------------------- - * Memory Bank 3 (Second-Flash) initialization - * 0xF0000000...0xF01FFFFF -> 2MB - *----------------------------------------------------------------------- */ - - li r4,PB3AP /* Peripheral Bank 1 Access Parameter */ - mtdcr EBC0_CFGADDR,r4 - mtdcr EBC0_CFGDATA,r2 /* change timing */ - - li r4,PB3CR /* Peripheral Bank 1 Configuration Registers */ - mtdcr EBC0_CFGADDR,r4 - - lis r4,0xF003 - ori r4,r4,0x8000 -/* - * Consider boot configuration - */ - xori r24,r24,0x2000 /* invert current bus width */ - or r4,r4,r24 - mtdcr EBC0_CFGDATA,r4 - -/*----------------------------------------------------------------------- - * Memory Bank 1 (NAND-Flash) initialization - * 0x77D00000...0x77DFFFFF -> 1MB - * - the write/read pulse to the NAND can be as short as 25ns, bus the cycle time is always 50ns - * - the setup time is 0ns - * - the hold time is 15ns - * -> - * - TWT = 0 - * - CSN = 0 - * - OEN = 0 - * - WBN = 0 - * - WBF = 0 - * - TH = 1 - * ----> 2 clocks per cycle = 60ns cycle (30ns active, 30ns hold) - *----------------------------------------------------------------------- */ - - li r4,PB1AP /* Peripheral Bank 1 Access Parameter */ - mtdcr EBC0_CFGADDR,r4 - - lis r4,0x0000 - ori r4,r4,0x0200 - mtdcr EBC0_CFGDATA,r4 - - li r4,PB1CR /* Peripheral Bank 1 Configuration Registers */ - mtdcr EBC0_CFGADDR,r4 - - lis r4,0x77D1 - ori r4,r4,0x8000 - mtdcr EBC0_CFGDATA,r4 - - -/* USB init (without acceleration) */ -#ifndef CONFIG_ISP1161_PRESENT - li r4,PB4AP /* PB4AP=Peripheral Bank 4 Access Parameters */ - mtdcr EBC0_CFGADDR,r4 - lis r4,0x0180 - ori r4,r4,0x5940 - mtdcr EBC0_CFGDATA,r4 -#endif - -/*----------------------------------------------------------------------- - * Memory Bank 2 (ISA Access) initialization (plus memory bank 6 and 7) - * 0x78000000...0x7BFFFFFF -> 64 MB - * Wir arbeiten bei 33 MHz -> 30ns - *----------------------------------------------------------------------- - - A7 (ppc notation) or A24 (standard notation) decides about - the type of access: - A7/A24=0 -> memory cycle - A7/ /A24=1 -> I/O cycle -*/ - li r4,PB2AP /* PB2AP=Peripheral Bank 2 Access Parameters */ - mtdcr EBC0_CFGADDR,r4 -/* - We emulate an ISA access - - 1. Address active - 2. wait 0 EBC clocks -> CSN=0 - 3. set CS# - 4. wait 0 EBC clock -> OEN/WBN=0 - 5. set OE#/WE# - 6. wait 4 clocks (ca. 90ns) and for Ready signal - 7. hold for 4 clocks -> TH=4 -*/ - -#if 1 -/* faster access to isa-bus */ - lis r4,0x0180 - ori r4,r4,0x5940 -#else - lis r4,0x0100 - ori r4,r4,0x0340 -#endif - mtdcr EBC0_CFGDATA,r4 - -#ifdef IDE_USES_ISA_EMULATION - li r25,PB5AP /* PB5AP=Peripheral Bank 5 Access Parameters */ - mtdcr EBC0_CFGADDR,r25 - mtdcr EBC0_CFGDATA,r4 -#endif - - li r25,PB6AP /* PB6AP=Peripheral Bank 6 Access Parameters */ - mtdcr EBC0_CFGADDR,r25 - mtdcr EBC0_CFGDATA,r4 - li r25,PB7AP /* PB7AP=Peripheral Bank 7 Access Parameters */ - mtdcr EBC0_CFGADDR,r25 - mtdcr EBC0_CFGDATA,r4 - - li r25,PB2CR /* PB2CR=Peripheral Bank 2 Configuration Register */ - mtdcr EBC0_CFGADDR,r25 - - lis r4,0x780B - ori r4,r4,0xA000 - mtdcr EBC0_CFGDATA,r4 -/* - * the other areas are only 1MiB in size - */ - lis r4,0x7401 - ori r4,r4,0xA000 - - li r25,PB6CR /* PB6CR=Peripheral Bank 6 Configuration Register */ - mtdcr EBC0_CFGADDR,r25 - lis r4,0x7401 - ori r4,r4,0xA000 - mtdcr EBC0_CFGDATA,r4 - - li r25,PB7CR /* PB7CR=Peripheral Bank 7 Configuration Register */ - mtdcr EBC0_CFGADDR,r25 - lis r4,0x7411 - ori r4,r4,0xA000 - mtdcr EBC0_CFGDATA,r4 - -#ifndef CONFIG_ISP1161_PRESENT - li r25,PB4CR /* PB4CR=Peripheral Bank 4 Configuration Register */ - mtdcr EBC0_CFGADDR,r25 - lis r4,0x7421 - ori r4,r4,0xA000 - mtdcr EBC0_CFGDATA,r4 -#endif -#ifdef IDE_USES_ISA_EMULATION - li r25,PB5CR /* PB5CR=Peripheral Bank 5 Configuration Register */ - mtdcr EBC0_CFGADDR,r25 - lis r4,0x0000 - ori r4,r4,0x0000 - mtdcr EBC0_CFGDATA,r4 -#endif - -/*----------------------------------------------------------------------- - * Memory bank 4: USB controller Philips ISP6111 - * 0x77C00000 ... 0x77CFFFFF - * - * The chip is connected to: - * - CPU CS#4 - * - CPU IRQ#2 - * - CPU DMA 3 - * - * Timing: - * - command to first data: 300ns. Software must ensure this timing! - * - Write pulse: 26ns - * - Read pulse: 33ns - * - read cycle time: 150ns - * - write cycle time: 140ns - * - * Note: All calculations are based on 33MHz EBC clock. One '#' or '_' is 30ns - * - * |- 300ns --| - * |---- 420ns ---|---- 420ns ---| cycle - * CS ############:###____#######:###____####### - * OE ############:####___#######:####___####### - * WE ############:####__########:####__######## - * - * ----> 2 clocks RD/WR pulses: 60ns - * ----> CSN: 3 clock, 90ns - * ----> OEN: 1 clocks (read cycle) - * ----> WBN: 1 clocks (write cycle) - * ----> WBE: 2 clocks - * ----> TH: 7 clock, 210ns - * ----> TWT: 7 clocks - *----------------------------------------------------------------------- */ - -#ifdef CONFIG_ISP1161_PRESENT - - li r4,PB4AP /* PB4AP=Peripheral Bank 4 Access Parameters */ - mtdcr EBC0_CFGADDR,r4 - - lis r4,0x030D - ori r4,r4,0x5E80 - mtdcr EBC0_CFGDATA,r4 - - li r4,PB4CR /* PB2CR=Peripheral Bank 4 Configuration Register */ - mtdcr EBC0_CFGADDR,r4 - - lis r4,0x77C1 - ori r4,r4,0xA000 - mtdcr EBC0_CFGDATA,r4 - -#endif - -#ifndef IDE_USES_ISA_EMULATION - -/*----------------------------------------------------------------------- - * Memory Bank 5 used for IDE access - * - * Timings for IDE Interface - * - * SETUP / LENGTH / HOLD - cycles valid for 33.3 MHz clk -> 30ns cycle time - * 70 165 30 PIO-Mode 0, [ns] - * 3 6 1 [Cycles] ----> AP=0x040C0200 - * 50 125 20 PIO-Mode 1, [ns] - * 2 5 1 [Cycles] ----> AP=0x03080200 - * 30 100 15 PIO-Mode 2, [ns] - * 1 4 1 [Cycles] ----> AP=0x02040200 - * 30 80 10 PIO-Mode 3, [ns] - * 1 3 1 [Cycles] ----> AP=0x01840200 - * 25 70 10 PIO-Mode 4, [ns] - * 1 3 1 [Cycles] ----> AP=0x01840200 - * - *----------------------------------------------------------------------- */ - - li r4,PB5AP - mtdcr EBC0_CFGADDR,r4 - lis r4,0x040C - ori r4,r4,0x0200 - mtdcr EBC0_CFGDATA,r4 - - li r4,PB5CR /* PB2CR=Peripheral Bank 2 Configuration Register */ - mtdcr EBC0_CFGADDR,r4 - - lis r4,0x7A01 - ori r4,r4,0xA000 - mtdcr EBC0_CFGDATA,r4 -#endif -/* - * External Peripheral Control Register - */ - li r4,EBC0_CFG - mtdcr EBC0_CFGADDR,r4 - - lis r4,0xB84E - ori r4,r4,0xF000 - mtdcr EBC0_CFGDATA,r4 -/* - * drive POST code - */ - lis r4,0x7900 - ori r4,r4,0x0080 - li r3,0x0001 - stb r3,0(r4) /* 01 -> external bus controller is initialized */ - nop /* pass2 DCR errata #8 */ - blr |