diff options
Diffstat (limited to 'board/kosagi/novena/novena_spl.c')
| -rw-r--r-- | board/kosagi/novena/novena_spl.c | 64 |
1 files changed, 46 insertions, 18 deletions
diff --git a/board/kosagi/novena/novena_spl.c b/board/kosagi/novena/novena_spl.c index a8389d9c6b..c4155ddee2 100644 --- a/board/kosagi/novena/novena_spl.c +++ b/board/kosagi/novena/novena_spl.c @@ -41,6 +41,10 @@ DECLARE_GLOBAL_DATA_PTR; PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ PAD_CTL_DSE_40ohm | PAD_CTL_HYS) +#define ENET_PHY_CFG_PAD_CTRL \ + (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_22K_UP | PAD_CTL_HYS) + #define RGMII_PAD_CTRL \ (PAD_CTL_PKE | PAD_CTL_PUE | \ PAD_CTL_PUS_100K_UP | PAD_CTL_DSE_40ohm | PAD_CTL_HYS) @@ -98,18 +102,20 @@ static iomux_v3_cfg_t enet_pads1[] = { MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(RGMII_PAD_CTRL), MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(RGMII_PAD_CTRL), MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL), - /* pin 35 - 1 (PHY_AD2) on reset */ - MX6_PAD_RGMII_RXC__GPIO6_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL), - /* pin 32 - 1 - (MODE0) all */ - MX6_PAD_RGMII_RD0__GPIO6_IO25 | MUX_PAD_CTRL(NO_PAD_CTRL), - /* pin 31 - 1 - (MODE1) all */ - MX6_PAD_RGMII_RD1__GPIO6_IO27 | MUX_PAD_CTRL(NO_PAD_CTRL), - /* pin 28 - 1 - (MODE2) all */ - MX6_PAD_RGMII_RD2__GPIO6_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL), - /* pin 27 - 1 - (MODE3) all */ - MX6_PAD_RGMII_RD3__GPIO6_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL), - /* pin 33 - 1 - (CLK125_EN) 125Mhz clockout enabled */ - MX6_PAD_RGMII_RX_CTL__GPIO6_IO24 | MUX_PAD_CTRL(NO_PAD_CTRL), + + /* pin 35, PHY_AD2 */ + MX6_PAD_RGMII_RXC__GPIO6_IO30 | MUX_PAD_CTRL(ENET_PHY_CFG_PAD_CTRL), + /* pin 32, MODE0 */ + MX6_PAD_RGMII_RD0__GPIO6_IO25 | MUX_PAD_CTRL(ENET_PHY_CFG_PAD_CTRL), + /* pin 31, MODE1 */ + MX6_PAD_RGMII_RD1__GPIO6_IO27 | MUX_PAD_CTRL(ENET_PHY_CFG_PAD_CTRL), + /* pin 28, MODE2 */ + MX6_PAD_RGMII_RD2__GPIO6_IO28 | MUX_PAD_CTRL(ENET_PHY_CFG_PAD_CTRL), + /* pin 27, MODE3 */ + MX6_PAD_RGMII_RD3__GPIO6_IO29 | MUX_PAD_CTRL(ENET_PHY_CFG_PAD_CTRL), + /* pin 33, CLK125_EN */ + MX6_PAD_RGMII_RX_CTL__GPIO6_IO24 | MUX_PAD_CTRL(ENET_PHY_CFG_PAD_CTRL), + /* pin 42 PHY nRST */ MX6_PAD_EIM_D23__GPIO3_IO23 | MUX_PAD_CTRL(NO_PAD_CTRL), }; @@ -127,15 +133,37 @@ static void novena_spl_setup_iomux_enet(void) { imx_iomux_v3_setup_multiple_pads(enet_pads1, ARRAY_SIZE(enet_pads1)); + /* Assert Ethernet PHY nRST */ gpio_direction_output(IMX_GPIO_NR(3, 23), 0); - gpio_direction_output(IMX_GPIO_NR(6, 30), 1); - gpio_direction_output(IMX_GPIO_NR(6, 25), 1); - gpio_direction_output(IMX_GPIO_NR(6, 27), 1); - gpio_direction_output(IMX_GPIO_NR(6, 28), 1); - gpio_direction_output(IMX_GPIO_NR(6, 29), 1); - gpio_direction_output(IMX_GPIO_NR(6, 24), 1); + /* + * Use imx6 internal pull-ups to drive PHY mode pins during PHY reset + * de-assertion. The intention is to use weak signal drivers (pull-ups) + * to prevent the conflict between PHY pins becoming outputs after + * reset and imx6 still driving the pins. The issue is described in PHY + * datasheet, p.14 + */ + gpio_direction_input(IMX_GPIO_NR(6, 30)); /* PHY_AD2 = 1 */ + gpio_direction_input(IMX_GPIO_NR(6, 25)); /* MODE0 = 1 */ + gpio_direction_input(IMX_GPIO_NR(6, 27)); /* MODE1 = 1 */ + gpio_direction_input(IMX_GPIO_NR(6, 28)); /* MODE2 = 1 */ + gpio_direction_input(IMX_GPIO_NR(6, 29)); /* MODE3 = 1 */ + gpio_direction_input(IMX_GPIO_NR(6, 24)); /* CLK125_EN = 1 */ + + /* Following reset timing (p.53, fig.8 from the PHY datasheet) */ + mdelay(10); + + /* De-assert Ethernet PHY nRST */ + gpio_set_value(IMX_GPIO_NR(3, 23), 1); + + /* PHY is now configured, connect FEC to the pads */ imx_iomux_v3_setup_multiple_pads(enet_pads2, ARRAY_SIZE(enet_pads2)); + + /* + * PHY datasheet recommends on p.53 to wait at least 100us after reset + * before using MII, so we enforce the delay here + */ + udelay(100); } /* |