diff options
Diffstat (limited to 'board/freescale/p1022ds/ddr.c')
-rw-r--r-- | board/freescale/p1022ds/ddr.c | 106 |
1 files changed, 106 insertions, 0 deletions
diff --git a/board/freescale/p1022ds/ddr.c b/board/freescale/p1022ds/ddr.c new file mode 100644 index 00000000000..7ecfb3e81b5 --- /dev/null +++ b/board/freescale/p1022ds/ddr.c @@ -0,0 +1,106 @@ +/* + * Copyright 2010 Freescale Semiconductor, Inc. + * Authors: Srikanth Srinivasan <srikanth.srinivasan@freescale.com> + * Timur Tabi <timur@freescale.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + */ + +#include <common.h> +#include <i2c.h> + +#include <asm/fsl_ddr_sdram.h> +#include <asm/fsl_ddr_dimm_params.h> + +unsigned int fsl_ddr_get_mem_data_rate(void) +{ + return get_ddr_freq(0); +} + +void fsl_ddr_get_spd(ddr3_spd_eeprom_t *ctrl_dimms_spd, unsigned int ctrl_num) +{ + int ret; + + /* + * The P1022 has only one DDR controller, and the board has only one + * DIMM slot. + */ + ret = i2c_read(SPD_EEPROM_ADDRESS1, 0, 1, (u8 *)ctrl_dimms_spd, + sizeof(ddr3_spd_eeprom_t)); + if (ret) { + debug("DDR: failed to read SPD from address %u\n", + SPD_EEPROM_ADDRESS1); + memset(ctrl_dimms_spd, 0, sizeof(ddr3_spd_eeprom_t)); + } +} + +typedef struct { + u32 datarate_mhz_low; + u32 datarate_mhz_high; + u32 n_ranks; + u32 clk_adjust; /* Range: 0-8 */ + u32 cpo; /* Range: 2-31 */ + u32 write_data_delay; /* Range: 0-6 */ + u32 force_2T; +} board_specific_parameters_t; + +static const board_specific_parameters_t bsp[] = { +/* + * lo| hi| num| clk| cpo|wrdata|2T + * mhz| mhz|ranks|adjst| | delay| + */ + { 0, 333, 1, 5, 31, 3, 0}, + {334, 400, 1, 5, 31, 3, 0}, + {401, 549, 1, 5, 31, 3, 0}, + {550, 680, 1, 5, 31, 5, 0}, + {681, 850, 1, 5, 31, 5, 0}, + { 0, 333, 2, 5, 31, 3, 0}, + {334, 400, 2, 5, 31, 3, 0}, + {401, 549, 2, 5, 31, 3, 0}, + {550, 680, 2, 5, 31, 5, 0}, + {681, 850, 2, 5, 31, 5, 0}, +}; + +void fsl_ddr_board_options(memctl_options_t *popts, dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + unsigned long ddr_freq; + unsigned int i; + + /* set odt_rd_cfg and odt_wr_cfg. */ + for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { + popts->cs_local_opts[i].odt_rd_cfg = 0; + popts->cs_local_opts[i].odt_wr_cfg = 1; + } + + /* + * Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr + * freqency and n_banks specified in board_specific_parameters table. + */ + ddr_freq = get_ddr_freq(0) / 1000000; + for (i = 0; i < ARRAY_SIZE(bsp); i++) { + if (ddr_freq >= bsp[i].datarate_mhz_low && + ddr_freq <= bsp[i].datarate_mhz_high && + pdimm->n_ranks == bsp[i].n_ranks) { + popts->clk_adjust = bsp[i].clk_adjust; + popts->cpo_override = bsp[i].cpo; + popts->write_data_delay = bsp[i].write_data_delay; + popts->twoT_en = bsp[i].force_2T; + break; + } + } + + popts->half_strength_driver_enable = 1; + + /* Per AN4039, enable ZQ calibration. */ + popts->zq_en = 1; + + /* + * For wake-up on ARP, we need auto self refresh enabled + */ + popts->auto_self_refresh_en = 1; + popts->sr_it = 0xb; +} |