diff options
Diffstat (limited to 'board/freescale/bsc9132qds/README')
| -rw-r--r-- | board/freescale/bsc9132qds/README | 150 |
1 files changed, 150 insertions, 0 deletions
diff --git a/board/freescale/bsc9132qds/README b/board/freescale/bsc9132qds/README new file mode 100644 index 0000000000..4a3dbfe5d4 --- /dev/null +++ b/board/freescale/bsc9132qds/README @@ -0,0 +1,150 @@ +Overview +-------- + The BSC9132 is a highly integrated device that targets the evolving + Microcell, Picocell, and Enterprise-Femto base station market subsegments. + + The BSC9132 device combines Power Architecture e500 and DSP StarCore SC3850 + core technologies with MAPLE-B2P baseband acceleration processing elements + to address the need for a high performance, low cost, integrated solution + that handles all required processing layers without the need for an + external device except for an RF transceiver or, in a Micro base station + configuration, a host device that handles the L3/L4 and handover between + sectors. + + The BSC9132 SoC includes the following function and features: + - Power Architecture subsystem including two e500 processors with + 512-Kbyte shared L2 cache + - Two StarCore SC3850 DSP subsystems, each with a 512-Kbyte private L2 + cache + - 32 Kbyte of shared M3 memory + - The Multi Accelerator Platform Engine for Pico BaseStation Baseband + Processing (MAPLE-B2P) + - Two DDR3/3L memory interfaces with 32-bit data width (40 bits including + ECC), up to 1333 MHz data rate + - Dedicated security engine featuring trusted boot + - Two DMA controllers + - OCNDMA with four bidirectional channels + - SysDMA with sixteen bidirectional channels + - Interfaces + - Four-lane SerDes PHY + - PCI Express controller complies with the PEX Specification-Rev 2.0 + - Two Common Public Radio Interface (CPRI) controller lanes + - High-speed USB 2.0 host and device controller with ULPI interface + - Enhanced secure digital (SD/MMC) host controller (eSDHC) + - Antenna interface controller (AIC), supporting four industry + standard JESD207/four custom ADI RF interfaces + - ADI lanes support both full duplex FDD support & half duplex TDD + - Universal Subscriber Identity Module (USIM) interface that + facilitates communication to SIM cards or Eurochip pre-paid phone + cards + - Two DUART, two eSPI, and two I2C controllers + - Integrated Flash memory controller (IFC) + - GPIO + - Sixteen 32-bit timers + +The SC3850 core subsystem consists of the following: + - 32 KB, 8-way, level 1 instruction cache (L1 ICache) + - 32 KB, 8-way, level 1 data cache (L1 DCache) + - 512 KB, 8-way, level 2 unified instruction/data cache (L2 cache/M2 memory) + - Memory management unit (MMU) + - Global interrupt controller ( GIC) + - Debug and profiling unit (DPU) + - Two 32-bit quad timers + +BSC9132QDS board Overview +------------------------- + 2Gbyte DDR3 (on board DDR), Dual Ranki + 32Mbyte 16bit NOR flash + 128Mbyte 2K page size NAND Flash + 256 Kbit M24256 I2C EEPROM + 128 Mbit SPI Flash memory + SD slot + USB-ULPI + eTSEC1: Connected to SGMII PHY + eTSEC2: Connected to SGMII PHY + PCIe + CPRI + SerDes + I2C RTC + DUART interface: supports one UARTs up to 115200 bps for console display + +Frequency Combinations Supported +-------------------------------- +Core MHz/CCB MHz/DDR(MT/s) +1. CPU0/CPU1/CCB/DDR: 1000MHz/1000MHz/500MHz/800MHz + (SYSCLK = 100MHz, DDRCLK = 100MHz) +2. CPU0/CPU1/CCB/DDR: 1200MHz/1200MHz/600MHz/1330MHz + (SYSCLK = 100MHz, DDRCLK = 133MHz) + +Boot Methods Supported +----------------------- +1. NOR Flash +2. NAND Flash +3. SD Card +4. SPI flash + +Default Boot Method +-------------------- +NOR boot + +Building U-boot +-------------- +To build the u-boot for BSC9132QDS: +1. NOR Flash + make BSC9132QDS_NOR_DDRCLK100 : For 100MHZ DDR CLK + make BSC9132QDS_NOR_DDRCLK133 : For 133MHZ DDR CLK +2. NAND Flash : It is currently not supported +3. SPI Flash + make BSC9132QDS_SPIFLASH_DDRCLK100 : For 100MHZ DDR CLK + make BSC9132QDS_SPIFLASH_DDRCLK133 : For 133MHZ DDR CLK +4. SD Card + make BSC9132QDS_SDCARD_DDRCLK100 : For 100MHZ DDR CLK + make BSC9132QDS_SDCARD_DDRCLK133 : For 133MHZ DDR CLK + +Memory map +----------- + 0x0000_0000 0x7FFF_FFFF DDR 2G cacheable + 0x8000_0000 0x8FFF_FFFF NOR Flash 256M + 0x9000_0000 0x9FFF_FFFF PCIe Memory 256M + 0xA000_0000 0xA7FF_FFFF DSP core1 L2 space 128M + 0xB000_0000 0xB0FF_FFFF DSP core0 M2 space 16M + 0xB100_0000 0xB1FF_FFFF DSP core1 M2 space 16M + 0xC000_0000 0xC000_7FFF M3 Memory 32K + 0xC001_0000 0xC001_FFFF PCI Express I/O 64K + 0xC100_0000 0xC13F_FFFF MAPLE-2F 4M + 0xC1F0_0000 0xC1F7_FFFF PA SRAM Region 0 512K + 0xC1F8_0000 0xC1FB_FFFF PA SRAM Region 1 512K + 0xFED0_0000 0xFED0_3FFF SEC Secured RAM 16K + 0xFEE0_0000 0xFEE0_0FFF DSP Boot ROM 4K + 0xFF60_0000 0xFF6F_FFFF DSP CCSR 1M + 0xFF70_0000 0xFF7F_FFFF PA CCSR 1M + 0xFF80_0000 0xFFFF_FFFF Boot Page & NAND Buffer 8M + +Flashing Images +--------------- +To place a new u-boot image in the NAND flash and then boot +with that new image temporarily, use this: + tftp 1000000 u-boot-nand.bin + nand erase 0 100000 + nand write 1000000 0 100000 + reset + +Using the Device Tree Source File +--------------------------------- +To create the DTB (Device Tree Binary) image file, +use a command similar to this: + + dtc -b 0 -f -I dts -O dtb bsc9132qds.dts > bsc9132qds.dtb + +Likely, that .dts file will come from here; + + linux-2.6/arch/powerpc/boot/dts/bsc9132qds.dts + +Booting Linux +------------- +Place a linux uImage in the TFTP disk area. + + tftp 1000000 uImage + tftp 2000000 rootfs.ext2.gz.uboot + tftp c00000 bsc9132qds.dtb + bootm 1000000 2000000 c00000 |