diff options
Diffstat (limited to 'board/freescale/bsc9131rdb/README')
| -rw-r--r-- | board/freescale/bsc9131rdb/README | 137 |
1 files changed, 137 insertions, 0 deletions
diff --git a/board/freescale/bsc9131rdb/README b/board/freescale/bsc9131rdb/README new file mode 100644 index 0000000000..065faa378d --- /dev/null +++ b/board/freescale/bsc9131rdb/README @@ -0,0 +1,137 @@ +Overview +-------- +- BSC9131 is integrated device that targets Femto base station market. + It combines Power Architecture e500v2 and DSP StarCore SC3850 core + technologies with MAPLE-B2F baseband acceleration processing elements. +- It's MAPLE disabled personality is called 9231. + +The BSC9131 SoC includes the following function and features: +. Power Architecture subsystem including a e500 processor with 256-Kbyte shared + L2 cache +. StarCore SC3850 DSP subsystem with a 512-Kbyte private L2 cache +. The Multi Accelerator Platform Engine for Femto BaseStation Baseband + Processing (MAPLE-B2F) +. A multi-standard baseband algorithm accelerator for Channel Decoding/Encoding, + Fourier Transforms, UMTS chip rate processing, LTE UP/DL Channel processing, + and CRC algorithms +. Consists of accelerators for Convolution, Filtering, Turbo Encoding, + Turbo Decoding, Viterbi decoding, Chiprate processing, and Matrix Inversion + operations +. DDR3/3L memory interface with 32-bit data width without ECC and 16-bit with + ECC, up to 400-MHz clock/800 MHz data rate +. Dedicated security engine featuring trusted boot +. DMA controller +. OCNDMA with four bidirectional channels +. Interfaces +. Two triple-speed Gigabit Ethernet controllers featuring network acceleration + including IEEE 1588. v2 hardware support and virtualization (eTSEC) +. eTSEC 1 supports RGMII/RMII +. eTSEC 2 supports RGMII +. High-speed USB 2.0 host and device controller with ULPI interface +. Enhanced secure digital (SD/MMC) host controller (eSDHC) +. Antenna interface controller (AIC), supporting three industry standard + JESD207/three custom ADI RF interfaces (two dual port and one single port) + and three MAXIM's MaxPHY serial interfaces +. ADI lanes support both full duplex FDD support and half duplex TDD support +. Universal Subscriber Identity Module (USIM) interface that facilitates + communication to SIM cards or Eurochip pre-paid phone cards +. TDM with one TDM port +. Two DUART, four eSPI, and two I2C controllers +. Integrated Flash memory controller (IFC) +. TDM with 256 channels +. GPIO +. Sixteen 32-bit timers + +The e500 core subsystem within the Power Architecture consists of the following: +. 32-Kbyte L1 instruction cache +. 32-Kbyte L1 data cache +. 256-Kbyte L2 cache/L2 memory/L2 stash +. programmable interrupt controller (PIC) +. Debug support +. Timers + +The SC3850 core subsystem consists of the following: +. 32 Kbyte 8-way level 1 instruction cache (L1 ICache) +. 32 Kbyte 8-way level 1 data cache (L1 DCache) +. 512 Kbyte 8-way level 2 unified instruction/data cache (M2 memory) +. Memory management unit (MMU) +. Enhanced programmable interrupt controller (EPIC) +. Debug and profiling unit (DPU) +. Two 32-bit timers + +BSC9131RDB board Overview +------------------------- + 1Gbyte DDR3 (on board DDR) + 128Mbyte 2K page size NAND Flash + 256 Kbit M24256 I2C EEPROM + 128 Mbit SPI Flash memory + USB-ULPI + eTSEC1: Connected to RGMII PHY + eTSEC2: Connected to RGMII PHY + DUART interface: supports one UARTs up to 115200 bps for console display + USIM connector + +Frequency Combinations Supported +-------------------------------- +Core MHz/CCB MHz/DDR(MT/s) +1. 1000/500/800 +2. 800/400/667 + +Boot Methods Supported +----------------------- +1. NAND Flash +2. SPI Flash + +Default Boot Method +-------------------- +NAND boot + +Building U-boot +-------------- +To build the u-boot for BSC9131RDB: +1. NAND Flash + make BSC9131RDB_NAND +2. SPI Flash + make BSC9131RDB_SPIFLASH + +Memory map +----------- + 0x0000_0000 0x7FFF_FFFF DDR 1G cacheable + 0xA0000000 0xBFFFFFFF Shared DSP core L2/M2 space 512M + 0xC100_0000 0xC13F_FFFF MAPLE-2F 4M + 0xC1F0_0000 0xC1F3_FFFF PA SRAM Region 0 256K + 0xC1F8_0000 0xC1F9_FFFF PA SRAM Region 1 128K + 0xFED0_0000 0xFED0_3FFF SEC Secured RAM 16K + 0xFEE0_0000 0xFEE0_0FFF DSP Boot ROM 4K + 0xFF60_0000 0xFF6F_FFFF DSP CCSR 1M + 0xFF70_0000 0xFF7F_FFFF PA CCSR 1M + 0xFF80_0000 0xFFFF_FFFF Boot Page & NAND Buffer 8M + +Flashing Images +--------------- +To place a new u-boot image in the NAND flash and then boot +with that new image temporarily, use this: + tftp 1000000 u-boot-nand.bin + nand erase 0 100000 + nand write 1000000 0 100000 + reset + +Using the Device Tree Source File +--------------------------------- +To create the DTB (Device Tree Binary) image file, +use a command similar to this: + + dtc -b 0 -f -I dts -O dtb bsc9131rdb.dts > bsc9131rdb.dtb + +Likely, that .dts file will come from here; + + linux-2.6/arch/powerpc/boot/dts/bsc9131rdb.dts + +Booting Linux +------------- +Place a linux uImage in the TFTP disk area. + + tftp 1000000 uImage + tftp 2000000 rootfs.ext2.gz.uboot + tftp c00000 bsc9131rdb.dtb + bootm 1000000 2000000 c00000 |