diff options
Diffstat (limited to 'board/bf533-stamp')
-rw-r--r-- | board/bf533-stamp/bf533-stamp.c | 33 | ||||
-rw-r--r-- | board/bf533-stamp/spi.c | 39 |
2 files changed, 37 insertions, 35 deletions
diff --git a/board/bf533-stamp/bf533-stamp.c b/board/bf533-stamp/bf533-stamp.c index 3e074e3a1b2..2f6e75187b1 100644 --- a/board/bf533-stamp/bf533-stamp.c +++ b/board/bf533-stamp/bf533-stamp.c @@ -27,6 +27,7 @@ #include <common.h> #include <asm/mem_init.h> +#include <asm/io.h> #include "bf533-stamp.h" #define STATUS_LED_OFF 0 @@ -74,9 +75,9 @@ void swap_to(int device_id) if (device_id == ETHERNET) { *pFIO_DIR = PF0; - __builtin_bfin_ssync(); + sync(); *pFIO_FLAG_S = PF0; - __builtin_bfin_ssync(); + sync(); } else if (device_id == FLASH) { *pFIO_DIR = (PF4 | PF3 | PF2 | PF1 | PF0); *pFIO_FLAG_S = (PF4 | PF3 | PF2); @@ -86,7 +87,7 @@ void swap_to(int device_id) *pFIO_EDGE = (PF8 | PF7 | PF6 | PF5); *pFIO_INEN = (PF8 | PF7 | PF6 | PF5); *pFIO_FLAG_D = (PF4 | PF3 | PF2); - __builtin_bfin_ssync(); + sync(); } else { printf("Unknown bank to switch\n"); } @@ -153,15 +154,15 @@ void cf_outb(unsigned char val, volatile unsigned char *addr) */ *pFIO_FLAG_S = CF_PF0; *pFIO_FLAG_C = CF_PF1; - __builtin_bfin_ssync(); + sync(); *(addr) = val; - __builtin_bfin_ssync(); + sync(); /* Setback PF1 PF0 to 0 0 to address external * memory banks */ *(volatile unsigned short *)pFIO_FLAG_C = CF_PF1_PF0; - __builtin_bfin_ssync(); + sync(); } unsigned char cf_inb(volatile unsigned char *addr) @@ -170,13 +171,13 @@ unsigned char cf_inb(volatile unsigned char *addr) *pFIO_FLAG_S = CF_PF0; *pFIO_FLAG_C = CF_PF1; - __builtin_bfin_ssync(); + sync(); c = *(addr); - __builtin_bfin_ssync(); + sync(); *pFIO_FLAG_C = CF_PF1_PF0; - __builtin_bfin_ssync(); + sync(); return c; } @@ -187,15 +188,15 @@ void cf_insw(unsigned short *sect_buf, unsigned short *addr, int words) *pFIO_FLAG_S = CF_PF0; *pFIO_FLAG_C = CF_PF1; - __builtin_bfin_ssync(); + sync(); for (i = 0; i < words; i++) { *(sect_buf + i) = *(addr); - __builtin_bfin_ssync(); + sync(); } *pFIO_FLAG_C = CF_PF1_PF0; - __builtin_bfin_ssync(); + sync(); } void cf_outsw(unsigned short *addr, unsigned short *sect_buf, int words) @@ -204,15 +205,15 @@ void cf_outsw(unsigned short *addr, unsigned short *sect_buf, int words) *pFIO_FLAG_S = CF_PF0; *pFIO_FLAG_C = CF_PF1; - __builtin_bfin_ssync(); + sync(); for (i = 0; i < words; i++) { *(addr) = *(sect_buf + i); - __builtin_bfin_ssync(); + sync(); } *pFIO_FLAG_C = CF_PF1_PF0; - __builtin_bfin_ssync(); + sync(); } #endif @@ -233,7 +234,7 @@ void stamp_led_set(int LED1, int LED2, int LED3) *pFIO_FLAG_S = PF4; else *pFIO_FLAG_C = PF4; - __builtin_bfin_ssync(); + sync(); } void show_boot_progress(int status) diff --git a/board/bf533-stamp/spi.c b/board/bf533-stamp/spi.c index 1b585aac954..d30750faa3b 100644 --- a/board/bf533-stamp/spi.c +++ b/board/bf533-stamp/spi.c @@ -3,6 +3,7 @@ ****************************************************************************/ #include <common.h> #include <linux/ctype.h> +#include <asm/io.h> #if defined(CONFIG_SPI) @@ -152,7 +153,7 @@ void SendSingleCommand(const int iCommand) /*sends the actual command to the SPI TX register */ *pSPI_TDBR = iCommand; - __builtin_bfin_ssync(); + sync(); /*The SPI status register will be polled to check the SPIF bit */ Wait_For_SPIF(); @@ -173,7 +174,7 @@ void SetupSPI(const int spi_setting) *pSPI_FLG = 0xFB04; *pSPI_BAUD = CONFIG_SPI_BAUD; *pSPI_CTL = spi_setting; - __builtin_bfin_ssync(); + sync(); } void SPI_OFF(void) @@ -182,7 +183,7 @@ void SPI_OFF(void) *pSPI_CTL = 0x0400; /* disable SPI */ *pSPI_FLG = 0; *pSPI_BAUD = 0; - __builtin_bfin_ssync(); + sync(); udelay(CONFIG_CCLK_HZ / 50000000); } @@ -240,10 +241,10 @@ char ReadStatusRegister(void) SetupSPI((COMMON_SPI_SETTINGS | TIMOD01)); /* Turn on the SPI */ *pSPI_TDBR = SPI_RDSR; /* send instruction to read status register */ - __builtin_bfin_ssync(); + sync(); Wait_For_SPIF(); /*wait until the instruction has been sent */ *pSPI_TDBR = 0; /*send dummy to receive the status register */ - __builtin_bfin_ssync(); + sync(); Wait_For_SPIF(); /*wait until the data has been sent */ status_register = *pSPI_RDBR; /*read the status register */ @@ -304,18 +305,18 @@ ERROR_CODE EraseBlock(int nBlock) /* Send the erase block command to the flash followed by the 24 address */ /* to point to the start of a sector. */ *pSPI_TDBR = SPI_SE; - __builtin_bfin_ssync(); + sync(); Wait_For_SPIF(); ShiftValue = (ulSectorOff >> 16); /* Send the highest byte of the 24 bit address at first */ *pSPI_TDBR = ShiftValue; - __builtin_bfin_ssync(); + sync(); Wait_For_SPIF(); /* Wait until the instruction has been sent */ ShiftValue = (ulSectorOff >> 8); /* Send the middle byte of the 24 bit address at second */ *pSPI_TDBR = ShiftValue; - __builtin_bfin_ssync(); + sync(); Wait_For_SPIF(); /* Wait until the instruction has been sent */ *pSPI_TDBR = ulSectorOff; /* Send the lowest byte of the 24 bit address finally */ - __builtin_bfin_ssync(); + sync(); Wait_For_SPIF(); /* Wait until the instruction has been sent */ /*Turns off the SPI */ @@ -350,25 +351,25 @@ ERROR_CODE ReadData(unsigned long ulStart, long lCount, int *pnData) SetupSPI((COMMON_SPI_SETTINGS | TIMOD01)); *pSPI_TDBR = SPI_READ; /* Send the read command to SPI device */ - __builtin_bfin_ssync(); + sync(); Wait_For_SPIF(); /* Wait until the instruction has been sent */ ShiftValue = (ulStart >> 16); /* Send the highest byte of the 24 bit address at first */ *pSPI_TDBR = ShiftValue; /* Send the byte to the SPI device */ - __builtin_bfin_ssync(); + sync(); Wait_For_SPIF(); /* Wait until the instruction has been sent */ ShiftValue = (ulStart >> 8); /* Send the middle byte of the 24 bit address at second */ *pSPI_TDBR = ShiftValue; /* Send the byte to the SPI device */ - __builtin_bfin_ssync(); + sync(); Wait_For_SPIF(); /* Wait until the instruction has been sent */ *pSPI_TDBR = ulStart; /* Send the lowest byte of the 24 bit address finally */ - __builtin_bfin_ssync(); + sync(); Wait_For_SPIF(); /* Wait until the instruction has been sent */ /* After the SPI device address has been placed on the MOSI pin the data can be */ /* received on the MISO pin. */ for (i = 0; i < lCount; i++) { *pSPI_TDBR = 0; /*send dummy */ - __builtin_bfin_ssync(); + sync(); while (!(*pSPI_STAT & RXS)) ; *cnData++ = *pSPI_RDBR; /*read */ @@ -405,26 +406,26 @@ ERROR_CODE WriteFlash(unsigned long ulStartAddr, long lTransferCount, /* Third, the 24 bit address will be shifted out the SPI MOSI bytewise. */ SetupSPI((COMMON_SPI_SETTINGS | TIMOD01)); /* Turns the SPI on */ *pSPI_TDBR = SPI_PP; - __builtin_bfin_ssync(); + sync(); Wait_For_SPIF(); /*wait until the instruction has been sent */ ulWAddr = (ulStartAddr >> 16); *pSPI_TDBR = ulWAddr; - __builtin_bfin_ssync(); + sync(); Wait_For_SPIF(); /*wait until the instruction has been sent */ ulWAddr = (ulStartAddr >> 8); *pSPI_TDBR = ulWAddr; - __builtin_bfin_ssync(); + sync(); Wait_For_SPIF(); /*wait until the instruction has been sent */ ulWAddr = ulStartAddr; *pSPI_TDBR = ulWAddr; - __builtin_bfin_ssync(); + sync(); Wait_For_SPIF(); /*wait until the instruction has been sent */ /* Fourth, maximum number of 256 bytes will be taken from the Buffer */ /* and sent to the SPI device. */ for (i = 0; (i < lTransferCount) && (i < 256); i++, lWTransferCount++) { iData = *temp; *pSPI_TDBR = iData; - __builtin_bfin_ssync(); + sync(); Wait_For_SPIF(); /*wait until the instruction has been sent */ temp++; } |