summaryrefslogtreecommitdiff
path: root/board/Marvell/openrd/kwbimage.cfg
diff options
context:
space:
mode:
Diffstat (limited to 'board/Marvell/openrd/kwbimage.cfg')
-rw-r--r--board/Marvell/openrd/kwbimage.cfg152
1 files changed, 0 insertions, 152 deletions
diff --git a/board/Marvell/openrd/kwbimage.cfg b/board/Marvell/openrd/kwbimage.cfg
deleted file mode 100644
index 8e5993715e..0000000000
--- a/board/Marvell/openrd/kwbimage.cfg
+++ /dev/null
@@ -1,152 +0,0 @@
-#
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Refer doc/README.kwbimage for more details about how-to configure
-# and create kirkwood boot image
-#
-
-# Boot Media configurations
-BOOT_FROM nand
-NAND_ECC_MODE default
-NAND_PAGE_SIZE 0x0800
-
-# SOC registers configuration using bootrom header extension
-# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
-
-# Configure RGMII-0 interface pad voltage to 1.8V
-DATA 0xFFD100e0 0x1b1b1b9b
-
-#Dram initalization for SINGLE x16 CL=5 @ 400MHz
-DATA 0xFFD01400 0x43000c30 # DDR Configuration register
-# bit13-0: 0xc30 (3120 DDR2 clks refresh rate)
-# bit23-14: zero
-# bit24: 1= enable exit self refresh mode on DDR access
-# bit25: 1 required
-# bit29-26: zero
-# bit31-30: 01
-
-DATA 0xFFD01404 0x37543000 # DDR Controller Control Low
-# bit 4: 0=addr/cmd in smame cycle
-# bit 5: 0=clk is driven during self refresh, we don't care for APX
-# bit 6: 0=use recommended falling edge of clk for addr/cmd
-# bit14: 0=input buffer always powered up
-# bit18: 1=cpu lock transaction enabled
-# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
-# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
-# bit30-28: 3 required
-# bit31: 0=no additional STARTBURST delay
-
-DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1)
-# bit3-0: TRAS lsbs
-# bit7-4: TRCD
-# bit11- 8: TRP
-# bit15-12: TWR
-# bit19-16: TWTR
-# bit20: TRAS msb
-# bit23-21: 0x0
-# bit27-24: TRRD
-# bit31-28: TRTP
-
-DATA 0xFFD0140C 0x00000a33 # DDR Timing (High)
-# bit6-0: TRFC
-# bit8-7: TR2R
-# bit10-9: TR2W
-# bit12-11: TW2W
-# bit31-13: zero required
-
-DATA 0xFFD01410 0x000000cc # DDR Address Control
-# bit1-0: 00, Cs0width=x8
-# bit3-2: 11, Cs0size=1Gb
-# bit5-4: 00, Cs1width=x8
-# bit7-6: 11, Cs1size=1Gb
-# bit9-8: 00, Cs2width=nonexistent
-# bit11-10: 00, Cs2size =nonexistent
-# bit13-12: 00, Cs3width=nonexistent
-# bit15-14: 00, Cs3size =nonexistent
-# bit16: 0, Cs0AddrSel
-# bit17: 0, Cs1AddrSel
-# bit18: 0, Cs2AddrSel
-# bit19: 0, Cs3AddrSel
-# bit31-20: 0 required
-
-DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
-# bit0: 0, OpenPage enabled
-# bit31-1: 0 required
-
-DATA 0xFFD01418 0x00000000 # DDR Operation
-# bit3-0: 0x0, DDR cmd
-# bit31-4: 0 required
-
-DATA 0xFFD0141C 0x00000C52 # DDR Mode
-# bit2-0: 2, BurstLen=2 required
-# bit3: 0, BurstType=0 required
-# bit6-4: 4, CL=5
-# bit7: 0, TestMode=0 normal
-# bit8: 0, DLL reset=0 normal
-# bit11-9: 6, auto-precharge write recovery ????????????
-# bit12: 0, PD must be zero
-# bit31-13: 0 required
-
-DATA 0xFFD01420 0x00000042 # DDR Extended Mode
-# bit0: 0, DDR DLL enabled
-# bit1: 1, DDR drive strength reduced
-# bit2: 0, DDR ODT control lsd (disabled)
-# bit5-3: 000, required
-# bit6: 1, DDR ODT control msb, (disabled)
-# bit9-7: 000, required
-# bit10: 0, differential DQS enabled
-# bit11: 0, required
-# bit12: 0, DDR output buffer enabled
-# bit31-13: 0 required
-
-DATA 0xFFD01424 0x0000F17F # DDR Controller Control High
-# bit2-0: 111, required
-# bit3 : 1 , MBUS Burst Chop disabled
-# bit6-4: 111, required
-# bit7 : 0
-# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
-# bit9 : 0 , no half clock cycle addition to dataout
-# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
-# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
-# bit15-12: 1111 required
-# bit31-16: 0 required
-
-DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
-DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
-
-DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
-DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size
-# bit0: 1, Window enabled
-# bit1: 0, Write Protect disabled
-# bit3-2: 00, CS0 hit selected
-# bit23-4: ones, required
-# bit31-24: 0x0F, Size (i.e. 256MB)
-
-DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb
-DATA 0xFFD0150C 0x0FFFFFF5 # CS[1]n Size 256Mb Window enabled for CS1
-
-DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
-DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
-
-DATA 0xFFD01494 0x00120012 # DDR ODT Control (Low)
-# bit3-0: 0010, (read) M_ODT[0] is asserted during read from DRAM CS1
-# bit7-4: 0001, (read) M_ODT[1] is asserted during read from DRAM CS0
-# bit19-16: 0010, (write) M_ODT[0] is asserted during write to DRAM CS1.
-# bit23-20: 0001, (write) M_ODT[1] is asserted during write to DRAM CS0.
-DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
-
-DATA 0xFFD0149C 0x0000E40f # CPU ODT Control
-# bit3-0: 1111, internal ODT is asserted during read from DRAM bank 0-3
-# bit11-10: 01, M_DQ, M_DM, and M_DQS I/O buffer ODT Select: 150 ohm
-# bit13-12: 10, M_STARTBURST_IN I/O buffer ODT Select: 75 ohm
-# bit14: 1, M_STARTBURST_IN ODT: Enabled
-# bit15: 1, DDR IO ODT Unit: Use ODT block
-DATA 0xFFD01480 0x00000001 # DDR Initialization Control
-#bit0=1, enable DDR init upon this register write
-
-# End of Header extension
-DATA 0x0 0x0