diff options
Diffstat (limited to 'arch/mips/Kconfig')
| -rw-r--r-- | arch/mips/Kconfig | 35 |
1 files changed, 3 insertions, 32 deletions
diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig index a5cec387a0..28234aa0bb 100644 --- a/arch/mips/Kconfig +++ b/arch/mips/Kconfig @@ -22,7 +22,7 @@ config TARGET_MALTA select DYNAMIC_IO_PORT_BASE select MIPS_CM select MIPS_INSERT_BOOT_CONFIG - select MIPS_L1_CACHE_SHIFT_6 + select SYS_CACHE_SHIFT_6 select MIPS_L2_CACHE select OF_CONTROL select OF_ISA_BUS @@ -132,7 +132,7 @@ config TARGET_BOSTON select DM select DM_SERIAL select MIPS_CM - select MIPS_L1_CACHE_SHIFT_6 + select SYS_CACHE_SHIFT_6 select MIPS_L2_CACHE select OF_BOARD_SETUP select OF_CONTROL @@ -153,7 +153,7 @@ config TARGET_XILFPGA select DM_ETH select DM_GPIO select DM_SERIAL - select MIPS_L1_CACHE_SHIFT_4 + select SYS_CACHE_SHIFT_4 select OF_CONTROL select ROM_EXCEPTION_VECTORS select SUPPORTS_CPU_MIPS32_R1 @@ -346,7 +346,6 @@ config MIPS_RELOCATION_TABLE_SIZE config RESTORE_EXCEPTION_VECTOR_BASE bool "Restore exception vector base before booting linux kernel" - default n help In U-Boot the exception vector base will be moved to top of memory, to be used to display register dump when exception occurs. @@ -361,7 +360,6 @@ config RESTORE_EXCEPTION_VECTOR_BASE config OVERRIDE_EXCEPTION_VECTOR_BASE bool "Override the exception vector base to be restored" depends on RESTORE_EXCEPTION_VECTOR_BASE - default n help Enable this option if you want to use a different exception vector base rather than the previously saved one. @@ -376,7 +374,6 @@ config NEW_EXCEPTION_VECTOR_BASE config INIT_STACK_WITHOUT_MALLOC_F bool "Do not reserve malloc space on initial stack" - default n help Enable this option if you don't want to reserve malloc space on initial stack. This is useful if the initial stack can't hold large @@ -385,7 +382,6 @@ config INIT_STACK_WITHOUT_MALLOC_F config SPL_INIT_STACK_WITHOUT_MALLOC_F bool "Do not reserve malloc space on initial stack in SPL" - default n help Enable this option if you don't want to reserve malloc space on initial stack. This is useful if the initial stack can't hold large @@ -394,7 +390,6 @@ config SPL_INIT_STACK_WITHOUT_MALLOC_F config SPL_LOADER_SUPPORT bool - default n help Enable this option if you want to use SPL loaders without DM enabled. @@ -422,7 +417,6 @@ config MIPS_BOOT_ENV_LEGACY config MIPS_BOOT_FDT bool "Hand over a flattened device tree to Linux kernel" - default n help Enable this option if you want U-Boot to hand over a flattened device tree to the kernel. According to UHI register $a0 will be set @@ -501,7 +495,6 @@ config SYS_MIPS_CACHE_INIT_RAM_LOAD config MIPS_INIT_STACK_IN_SRAM bool - default n help Select this if the initial stack frame could be setup in SRAM. Normally the initial stack frame is set up in DRAM which is often @@ -512,7 +505,6 @@ config MIPS_INIT_STACK_IN_SRAM config MIPS_SRAM_INIT bool - default n depends on MIPS_INIT_STACK_IN_SRAM help Select this if the SRAM for initial stack needs to be initialized @@ -566,26 +558,6 @@ config SYS_CACHE_SIZE_AUTO so if you know the cache configuration for your system at compile time it would be beneficial to configure it. -config MIPS_L1_CACHE_SHIFT_4 - bool - -config MIPS_L1_CACHE_SHIFT_5 - bool - -config MIPS_L1_CACHE_SHIFT_6 - bool - -config MIPS_L1_CACHE_SHIFT_7 - bool - -config MIPS_L1_CACHE_SHIFT - int - default "7" if MIPS_L1_CACHE_SHIFT_7 - default "6" if MIPS_L1_CACHE_SHIFT_6 - default "5" if MIPS_L1_CACHE_SHIFT_5 - default "4" if MIPS_L1_CACHE_SHIFT_4 - default "5" - config MIPS_L2_CACHE bool help @@ -604,7 +576,6 @@ config MIPS_CM config MIPS_INSERT_BOOT_CONFIG bool - default n help Enable this to insert some board-specific boot configuration in the U-Boot binary at offset 0x10. |