diff options
Diffstat (limited to 'arch/arm/dts/sun9i-a80-cubieboard4.dts')
| -rw-r--r-- | arch/arm/dts/sun9i-a80-cubieboard4.dts | 260 |
1 files changed, 238 insertions, 22 deletions
diff --git a/arch/arm/dts/sun9i-a80-cubieboard4.dts b/arch/arm/dts/sun9i-a80-cubieboard4.dts index 1526b41c70..85da85faf8 100644 --- a/arch/arm/dts/sun9i-a80-cubieboard4.dts +++ b/arch/arm/dts/sun9i-a80-cubieboard4.dts @@ -47,7 +47,6 @@ #include "sun9i-a80.dtsi" #include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/pinctrl/sun4i-a10.h> / { model = "Cubietech Cubieboard4"; @@ -63,8 +62,6 @@ leds { compatible = "gpio-leds"; - pinctrl-names = "default"; - pinctrl-0 = <&led_pins_cubieboard4>; green { label = "cubieboard4:green:usr"; @@ -76,18 +73,96 @@ gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */ }; }; + + vga-connector { + compatible = "vga-connector"; + label = "vga"; + ddc-i2c-bus = <&i2c3>; + + port { + vga_con_in: endpoint { + remote-endpoint = <&vga_dac_out>; + }; + }; + }; + + vga-dac { + compatible = "corpro,gm7123", "adi,adv7123", "dumb-vga-dac"; + vdd-supply = <®_dcdc1>; + #address-cells = <1>; + #size-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + vga_dac_in: endpoint@0 { + reg = <0>; + remote-endpoint = <&tcon0_out_vga>; + }; + }; + + port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + vga_dac_out: endpoint@0 { + reg = <0>; + remote-endpoint = <&vga_con_in>; + }; + }; + }; + }; + + wifi_pwrseq: wifi-pwrseq { + compatible = "mmc-pwrseq-simple"; + clocks = <&ac100_rtc 1>; + clock-names = "ext_clock"; + /* enables internal regulator and de-asserts reset */ + reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */ + }; +}; + +&de { + status = "okay"; +}; + +&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c3_pins>; + status = "okay"; }; &mmc0 { pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins>, <&mmc0_cd_pin_cubieboard4>; + pinctrl-0 = <&mmc0_pins>; vmmc-supply = <®_dcdc1>; bus-width = <4>; - cd-gpios = <&pio 7 18 GPIO_ACTIVE_HIGH>; /* PH18 */ - cd-inverted; + cd-gpios = <&pio 7 18 GPIO_ACTIVE_LOW>; /* PH18 */ + status = "okay"; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + vmmc-supply = <®_dldo1>; + vqmmc-supply = <®_cldo3>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; status = "okay"; }; +&mmc1_pins { + bias-pull-up; +}; + &mmc2 { pinctrl-names = "default"; pinctrl-0 = <&mmc2_8bit_pins>; @@ -100,23 +175,12 @@ &mmc2_8bit_pins { /* Increase drive strength for DDR modes */ - allwinner,drive = <SUN4I_PINCTRL_40_MA>; + drive-strength = <40>; }; -&pio { - led_pins_cubieboard4: led-pins@0 { - allwinner,pins = "PH6", "PH17"; - allwinner,function = "gpio_out"; - allwinner,drive = <SUN4I_PINCTRL_10_MA>; - allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; - }; - - mmc0_cd_pin_cubieboard4: mmc0_cd_pin@0 { - allwinner,pins = "PH18"; - allwinner,function = "gpio_in"; - allwinner,drive = <SUN4I_PINCTRL_10_MA>; - allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; - }; +&osc32k { + /* osc32k input is from AC100 */ + clocks = <&ac100_rtc 0>; }; &r_ir { @@ -248,14 +312,166 @@ reg_rtc_ldo: rtc_ldo { regulator-name = "vcc-rtc-vdd1v8-io"; }; + + sw { + /* unused */ + }; + }; + }; + + axp806: pmic@745 { + compatible = "x-powers,axp806"; + reg = <0x745>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <1>; + bldoin-supply = <®_dcdce>; + + regulators { + reg_s_aldo1: aldo1 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; + }; + + aldo2 { + /* + * unused, but use a different name to + * avoid name clash with axp809's aldo's + */ + regulator-name = "s_aldo2"; + }; + + aldo3 { + /* + * unused, but use a different name to + * avoid name clash with axp809's aldo's + */ + regulator-name = "s_aldo3"; + }; + + reg_bldo1: bldo1 { + regulator-always-on; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <1900000>; + regulator-name = "vcc18-efuse-adc-display-csi"; + }; + + reg_bldo2: bldo2 { + regulator-always-on; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <1900000>; + regulator-name = + "vdd18-drampll-vcc18-pll-cpvdd"; + }; + + bldo3 { + /* unused */ + }; + + reg_bldo4: bldo4 { + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1300000>; + regulator-name = "vcc12-hsic"; + }; + + reg_cldo1: cldo1 { + /* + * This was 3V in the original design, but + * 3.3V is the recommended supply voltage + * for the Ethernet PHY. + */ + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-gmac-phy"; + }; + + reg_cldo2: cldo2 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "afvcc-cam"; + }; + + reg_cldo3: cldo3 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-io-wifi-codec-io2"; + }; + + reg_dcdca: dcdca { + regulator-always-on; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpub"; + }; + + reg_dcdcd: dcdcd { + regulator-always-on; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-vpu"; + }; + + reg_dcdce: dcdce { + regulator-always-on; + regulator-min-microvolt = <2100000>; + regulator-max-microvolt = <2100000>; + regulator-name = "vcc-bldo-codec-ldoin"; + }; + + sw { + /* + * unused, but use a different name to + * avoid name clash with axp809's sw + */ + regulator-name = "s_sw"; + }; + }; + }; + + ac100: codec@e89 { + compatible = "x-powers,ac100"; + reg = <0xe89>; + + ac100_codec: codec { + compatible = "x-powers,ac100-codec"; + interrupt-parent = <&r_pio>; + interrupts = <0 9 IRQ_TYPE_LEVEL_LOW>; /* PL9 */ + #clock-cells = <0>; + clock-output-names = "4M_adda"; + }; + + ac100_rtc: rtc { + compatible = "x-powers,ac100-rtc"; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + clocks = <&ac100_codec>; + #clock-cells = <1>; + clock-output-names = "cko1_rtc", + "cko2_rtc", + "cko3_rtc"; }; }; }; #include "axp809.dtsi" +&tcon0 { + pinctrl-names = "default"; + pinctrl-0 = <&lcd0_rgb888_pins>; +}; + +&tcon0_out { + tcon0_out_vga: endpoint@0 { + reg = <0>; + remote-endpoint = <&vga_dac_in>; + }; +}; + &uart0 { pinctrl-names = "default"; - pinctrl-0 = <&uart0_pins_a>; + pinctrl-0 = <&uart0_ph_pins>; status = "okay"; }; |