diff options
Diffstat (limited to 'arch/arm/dts/sun8i-h3-orangepi-pc.dts')
| -rw-r--r-- | arch/arm/dts/sun8i-h3-orangepi-pc.dts | 139 |
1 files changed, 115 insertions, 24 deletions
diff --git a/arch/arm/dts/sun8i-h3-orangepi-pc.dts b/arch/arm/dts/sun8i-h3-orangepi-pc.dts index 3ae8f7c00e..4624033412 100644 --- a/arch/arm/dts/sun8i-h3-orangepi-pc.dts +++ b/arch/arm/dts/sun8i-h3-orangepi-pc.dts @@ -46,7 +46,6 @@ #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/input/input.h> -#include <dt-bindings/pinctrl/sun4i-a10.h> / { model = "Xunlong Orange Pi PC"; @@ -61,6 +60,17 @@ stdout-path = "serial0:115200n8"; }; + connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; + leds { compatible = "gpio-leds"; pinctrl-names = "default"; @@ -91,6 +101,26 @@ }; }; +&codec { + allwinner,audio-routing = + "Line Out", "LINEOUT", + "MIC1", "Mic", + "Mic", "MBIAS"; + status = "okay"; +}; + +&de { + status = "okay"; +}; + +&cpu0 { + cpu-supply = <®_vdd_cpux>; +}; + +&ehci0 { + status = "okay"; +}; + &ehci1 { status = "okay"; }; @@ -103,6 +133,23 @@ status = "okay"; }; +&emac { + phy-handle = <&int_mii_phy>; + phy-mode = "mii"; + allwinner,leds-active-low; + status = "okay"; +}; + +&hdmi { + status = "okay"; +}; + +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + &ir { pinctrl-names = "default"; pinctrl-0 = <&ir_pins_a>; @@ -112,8 +159,11 @@ &mmc0 { vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */ - cd-inverted; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ + status = "okay"; +}; + +&ohci0 { status = "okay"; }; @@ -130,44 +180,85 @@ }; &pio { - leds_opc: led_pins@0 { - allwinner,pins = "PA15"; - allwinner,function = "gpio_out"; - allwinner,drive = <SUN4I_PINCTRL_10_MA>; - allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + leds_opc: led_pins { + pins = "PA15"; + function = "gpio_out"; + }; +}; + +&r_i2c { + status = "okay"; + + reg_vdd_cpux: regulator@65 { + compatible = "silergy,sy8106a"; + reg = <0x65>; + regulator-name = "vdd-cpux"; + silergy,fixed-microvolt = <1200000>; + /* + * The datasheet uses 1.1V as the minimum value of VDD-CPUX, + * however both the Armbian DVFS table and the official one + * have operating points with voltage under 1.1V, and both + * DVFS table are known to work properly at the lowest + * operating point. + * + * Use 1.0V as the minimum voltage instead. + */ + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + regulator-always-on; }; }; &r_pio { - leds_r_opc: led_pins@0 { - allwinner,pins = "PL10"; - allwinner,function = "gpio_out"; - allwinner,drive = <SUN4I_PINCTRL_10_MA>; - allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + leds_r_opc: led_pins { + pins = "PL10"; + function = "gpio_out"; }; - sw_r_opc: key_pins@0 { - allwinner,pins = "PL3"; - allwinner,function = "gpio_in"; - allwinner,drive = <SUN4I_PINCTRL_10_MA>; - allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + sw_r_opc: key_pins { + pins = "PL3"; + function = "gpio_in"; }; }; +®_usb0_vbus { + gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */ + status = "okay"; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pins_a>; status = "okay"; }; -&usbphy { - /* USB VBUS is always on */ +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>; + status = "disabled"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; + status = "disabled"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins>; + status = "disabled"; +}; + +&usb_otg { + dr_mode = "otg"; status = "okay"; }; -&emac { - phy-handle = <&int_mii_phy>; - phy-mode = "mii"; - allwinner,leds-active-low; +&usbphy { + usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */ + usb0_vbus-supply = <®_usb0_vbus>; + /* VBUS on USB host ports are always on */ status = "okay"; }; |