1 files changed, 192 insertions, 0 deletions
diff --git a/arch/arm/dts/k3-am62-verdin-dev.dtsi b/arch/arm/dts/k3-am62-verdin-dev.dtsi
new file mode 100644
index 0000000000..54dabe1437
--- /dev/null
+++ b/arch/arm/dts/k3-am62-verdin-dev.dtsi
@@ -0,0 +1,192 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2023 Toradex
+ *
+ * Common dtsi for Verdin AM62 SoM on Development carrier board
+ *
+ * https://www.toradex.com/computer-on-modules/verdin-arm-family/ti-am62
+ * https://www.toradex.com/products/carrier-board/verdin-development-board-kit
+ */
+
+/* Verdin ETHs */
+&cpsw3g {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii1>, <&pinctrl_rgmii2>;
+	status = "okay";
+};
+
+/* MDIO, shared by Verdin ETH_1 (On-module PHY) and Verdin ETH_2_RGMII */
+&cpsw3g_mdio {
+	status = "okay";
+
+	cpsw3g_phy1: ethernet-phy@7 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <7>;
+		interrupt-parent = <&main_gpio0>;
+		interrupts = <38 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_eth2_rgmii_int>;
+		micrel,led-mode = <0>;
+	};
+};
+
+/* Verdin ETH_1 (On-module PHY) */
+&cpsw_port1 {
+	status = "okay";
+};
+
+/* Verdin ETH_2_RGMII */
+&cpsw_port2 {
+	phy-handle = <&cpsw3g_phy1>;
+	phy-mode = "rgmii-rxid";
+	status = "okay";
+};
+
+/* Verdin PWM_1, PWM_2 */
+&epwm0 {
+	status = "okay";
+};
+
+/* Verdin PWM_3_DSI */
+&epwm1 {
+	status = "okay";
+};
+
+&main_gpio0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ctrl_sleep_moci>,
+		    <&pinctrl_gpio_5>,
+		    <&pinctrl_gpio_6>,
+		    <&pinctrl_gpio_7>,
+		    <&pinctrl_gpio_8>;
+};
+
+/* Verdin I2C_1 */
+&main_i2c1 {
+	status = "okay";
+
+	/* IO Expander */
+	gpio_expander_21: gpio@21 {
+		compatible = "nxp,pcal6416";
+		reg = <0x21>;
+		#gpio-cells = <2>;
+		gpio-controller;
+	};
+
+	/* Current measurement into module VCC */
+	hwmon@40 {
+		compatible = "ti,ina219";
+		reg = <0x40>;
+		shunt-resistor = <10000>;
+	};
+
+	/* Temperature sensor */
+	sensor@4f {
+		compatible = "ti,tmp75c";
+		reg = <0x4f>;
+	};
+
+	/* EEPROM */
+	eeprom@57 {
+		compatible = "st,24c02", "atmel,24c02";
+		reg = <0x57>;
+		pagesize = <16>;
+	};
+};
+
+/* Verdin I2C_2_DSI */
+&main_i2c2 {
+	status = "okay";
+};
+
+/* Verdin I2C_4_CSI */
+&main_i2c3 {
+	status = "okay";
+};
+
+/* Verdin CAN_1 */
+&main_mcan0 {
+	status = "okay";
+};
+
+/* Verdin SPI_1 */
+&main_spi1 {
+	status = "okay";
+};
+
+/* Verdin UART_3 */
+&main_uart0 {
+	status = "okay";
+};
+
+/* Verdin UART_1, connector X50 through RS485 transceiver. */
+&main_uart1 {
+	linux,rs485-enabled-at-boot-time;
+	rs485-rx-during-tx;
+	status = "okay";
+};
+
+#if 0
+/* Verdin I2S_1 */
+&mcasp0 {
+	status = "okay";
+};
+#endif
+
+&mcu_gpio0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio_1>,
+		    <&pinctrl_gpio_2>,
+		    <&pinctrl_gpio_3>,
+		    <&pinctrl_gpio_4>;
+};
+
+/* Verdin I2C_3_HDMI */
+&mcu_i2c0 {
+	status = "okay";
+};
+
+/* Verdin UART_4 */
+&mcu_uart0 {
+	status = "okay";
+};
+
+/* Verdin QSPI_1 */
+&ospi0 {
+	status = "okay";
+};
+
+/* Verdin SD_1 */
+&sdhci1 {
+	ti,driver-strength-ohm = <33>;
+	status = "okay";
+};
+
+/* Verdin USB_1 */
+&usbss0 {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
+
+/* Verdin USB_2 */
+&usbss1 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};
+
+/* Verdin CTRL_WAKE1_MICO# */
+&verdin_gpio_keys {
+	status = "okay";
+};
+
+/* Verdin UART_2 */
+&wkup_uart0 {
+	/* FIXME: WKUP UART0 is used by DM firmware */
+	status = "reserved";
+};