diff options
93 files changed, 2954 insertions, 1295 deletions
diff --git a/MAINTAINERS b/MAINTAINERS index c209af57f91..aabd8713486 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -552,6 +552,7 @@ Stefano Babic <sbabic@denx.de> polaris xscale trizepsiv xscale mx51evk i.MX51 + vision2 i.MX51 Dirk Behme <dirk.behme@gmail.com> @@ -803,6 +804,10 @@ Hugo Villeneuve <hugo.villeneuve@lyrtech.com> SFFSDR ARM926EJS +Matt Waddel <matt.waddel@linaro.org> + + ca9x4_ct_vxp ARM ARMV7 (Quad Core) + Prafulla Wadaskar <prafulla@marvell.com> mv88f6281gtw_ge ARM926EJS (Kirkwood SoC) @@ -489,6 +489,7 @@ LIST_ARM11=" \ ######################################################################### LIST_ARMV7=" \ am3517_evm \ + ca9x4_ct_vxp \ devkit8000 \ mx51evk \ omap3_beagle \ diff --git a/arch/arm/cpu/arm1136/start.S b/arch/arm/cpu/arm1136/start.S index 8b631920c94..494768edfb2 100644 --- a/arch/arm/cpu/arm1136/start.S +++ b/arch/arm/cpu/arm1136/start.S @@ -235,8 +235,8 @@ stack_setup: copy_loop: ldmia r0!, {r9-r10} /* copy from source address [r0] */ stmia r6!, {r9-r10} /* copy to target address [r1] */ - cmp r0, r2 /* until source end addreee [r2] */ - ble copy_loop + cmp r0, r2 /* until source end address [r2] */ + blo copy_loop #ifndef CONFIG_PRELOADER /* fix got entries */ @@ -355,8 +355,8 @@ relocate: /* relocate U-Boot to RAM */ copy_loop: ldmia r0!, {r3-r10} /* copy from source address [r0] */ stmia r1!, {r3-r10} /* copy to target address [r1] */ - cmp r0, r2 /* until source end addreee [r2] */ - ble copy_loop + cmp r0, r2 /* until source end address [r2] */ + blo copy_loop #endif /* CONFIG_SKIP_RELOCATE_UBOOT */ /* Set up the stack */ diff --git a/arch/arm/cpu/arm1176/start.S b/arch/arm/cpu/arm1176/start.S index e5e7913d948..6277ae09215 100644 --- a/arch/arm/cpu/arm1176/start.S +++ b/arch/arm/cpu/arm1176/start.S @@ -284,8 +284,8 @@ stack_setup: copy_loop: ldmia r0!, {r9-r10} /* copy from source address [r0] */ stmia r6!, {r9-r10} /* copy to target address [r1] */ - cmp r0, r2 /* until source end addreee [r2] */ - ble copy_loop + cmp r0, r2 /* until source end address [r2] */ + blo copy_loop #ifndef CONFIG_PRELOADER /* fix got entries */ @@ -500,8 +500,8 @@ relocate: /* relocate U-Boot to RAM */ copy_loop: ldmia r0!, {r3-r10} /* copy from source address [r0] */ stmia r1!, {r3-r10} /* copy to target address [r1] */ - cmp r0, r2 /* until source end addreee [r2] */ - ble copy_loop + cmp r0, r2 /* until source end address [r2] */ + blo copy_loop #endif /* CONFIG_SKIP_RELOCATE_UBOOT */ #ifdef CONFIG_ENABLE_MMU @@ -559,7 +559,7 @@ clbss_l: str r2, [r0] /* clear loop... */ add r0, r0, #4 cmp r0, r1 - ble clbss_l + blo clbss_l #ifndef CONFIG_NAND_SPL ldr pc, _start_armboot diff --git a/arch/arm/cpu/arm720t/start.S b/arch/arm/cpu/arm720t/start.S index 0f5f6c46111..6a8d57b09c9 100644 --- a/arch/arm/cpu/arm720t/start.S +++ b/arch/arm/cpu/arm720t/start.S @@ -201,8 +201,8 @@ stack_setup: copy_loop: ldmia r0!, {r9-r10} /* copy from source address [r0] */ stmia r6!, {r9-r10} /* copy to target address [r1] */ - cmp r0, r2 /* until source end addreee [r2] */ - ble copy_loop + cmp r0, r2 /* until source end address [r2] */ + blo copy_loop #ifndef CONFIG_PRELOADER /* fix got entries */ @@ -318,8 +318,8 @@ relocate: /* relocate U-Boot to RAM */ copy_loop: ldmia r0!, {r3-r10} /* copy from source address [r0] */ stmia r1!, {r3-r10} /* copy to target address [r1] */ - cmp r0, r2 /* until source end addreee [r2] */ - ble copy_loop + cmp r0, r2 /* until source end address [r2] */ + blo copy_loop #endif /* CONFIG_SKIP_RELOCATE_UBOOT */ @@ -342,7 +342,7 @@ clear_bss: clbss_l:str r2, [r0] /* clear loop... */ add r0, r0, #4 cmp r0, r1 - ble clbss_l + blo clbss_l ldr pc, _start_armboot diff --git a/arch/arm/cpu/arm920t/start.S b/arch/arm/cpu/arm920t/start.S index a079bb27271..09ee815270a 100644 --- a/arch/arm/cpu/arm920t/start.S +++ b/arch/arm/cpu/arm920t/start.S @@ -246,8 +246,8 @@ stack_setup: copy_loop: ldmia r0!, {r9-r10} /* copy from source address [r0] */ stmia r6!, {r9-r10} /* copy to target address [r1] */ - cmp r0, r2 /* until source end addreee [r2] */ - ble copy_loop + cmp r0, r2 /* until source end address [r2] */ + blo copy_loop #ifndef CONFIG_PRELOADER /* fix got entries */ @@ -406,8 +406,8 @@ relocate: /* relocate U-Boot to RAM */ copy_loop: ldmia r0!, {r3-r10} /* copy from source address [r0] */ stmia r1!, {r3-r10} /* copy to target address [r1] */ - cmp r0, r2 /* until source end addreee [r2] */ - ble copy_loop + cmp r0, r2 /* until source end address [r2] */ + blo copy_loop #endif /* CONFIG_SKIP_RELOCATE_UBOOT */ /* Set up the stack */ @@ -429,7 +429,7 @@ clear_bss: clbss_l:str r2, [r0] /* clear loop... */ add r0, r0, #4 cmp r0, r1 - ble clbss_l + blo clbss_l ldr pc, _start_armboot diff --git a/arch/arm/cpu/arm925t/start.S b/arch/arm/cpu/arm925t/start.S index c0a856dfe1d..f173400ac3b 100644 --- a/arch/arm/cpu/arm925t/start.S +++ b/arch/arm/cpu/arm925t/start.S @@ -238,8 +238,8 @@ stack_setup: copy_loop: ldmia r0!, {r9-r10} /* copy from source address [r0] */ stmia r6!, {r9-r10} /* copy to target address [r1] */ - cmp r0, r2 /* until source end addreee [r2] */ - ble copy_loop + cmp r0, r2 /* until source end address [r2] */ + blo copy_loop #ifndef CONFIG_PRELOADER /* fix got entries */ @@ -377,8 +377,8 @@ relocate: /* relocate U-Boot to RAM */ copy_loop: ldmia r0!, {r3-r10} /* copy from source address [r0] */ stmia r1!, {r3-r10} /* copy to target address [r1] */ - cmp r0, r2 /* until source end addreee [r2] */ - ble copy_loop + cmp r0, r2 /* until source end address [r2] */ + blo copy_loop #endif /* CONFIG_SKIP_RELOCATE_UBOOT */ /* Set up the stack */ @@ -400,7 +400,7 @@ clear_bss: clbss_l:str r2, [r0] /* clear loop... */ add r0, r0, #4 cmp r0, r1 - ble clbss_l + blo clbss_l ldr pc, _start_armboot diff --git a/arch/arm/cpu/arm926ejs/at91/cpu.c b/arch/arm/cpu/arm926ejs/at91/cpu.c index 141a7d1ec63..5e30f1dccc4 100644 --- a/arch/arm/cpu/arm926ejs/at91/cpu.c +++ b/arch/arm/cpu/arm926ejs/at91/cpu.c @@ -1,4 +1,6 @@ /* + * (C) Copyright 2010 + * Reinhard Meyer, reinhard.meyer@emk-elektronik.de * (C) Copyright 2009 * Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> * @@ -22,12 +24,11 @@ */ #include <common.h> -#ifdef CONFIG_AT91_LEGACY -#warning Your board is using legacy SoC access. Please update! -#endif #include <asm/arch/hardware.h> #include <asm/arch/at91_pmc.h> +#include <asm/arch/at91_pit.h> +#include <asm/arch/at91_gpbr.h> #include <asm/arch/clk.h> #include <asm/arch/io.h> @@ -35,18 +36,26 @@ #define CONFIG_SYS_AT91_MAIN_CLOCK 0 #endif -/* - * The at91sam9260 has 4 GPBR (0-3), we'll use the last one, nr 3, - * to keep track of the bootcount. - */ -#define AT91_GPBR_BOOTCOUNT_REGISTER 3 -#define AT91_BOOTCOUNT_ADDRESS (AT91_GPBR + 4*AT91_GPBR_BOOTCOUNT_REGISTER) - int arch_cpu_init(void) { return at91_clock_init(CONFIG_SYS_AT91_MAIN_CLOCK); } +void arch_preboot_os(void) +{ + ulong cpiv; + at91_pit_t *pit = (at91_pit_t *) AT91_PIT_BASE; + + cpiv = AT91_PIT_MR_PIV_MASK(readl(&pit->piir)); + + /* + * Disable PITC + * Add 0x1000 to current counter to stop it faster + * without waiting for wrapping back to 0 + */ + writel(cpiv + 0x1000, &pit->mr); +} + #if defined(CONFIG_DISPLAY_CPUINFO) int print_cpuinfo(void) { @@ -66,27 +75,26 @@ int print_cpuinfo(void) #ifdef CONFIG_BOOTCOUNT_LIMIT /* - * Just as the mpc5xxx, we combine the BOOTCOUNT_MAGIC and boocount - * in one 32-bit register. This is done, as the AT91SAM9260 only has - * 4 GPBR. + * We combine the BOOTCOUNT_MAGIC and bootcount in one 32-bit register. + * This is done so we need to use only one of the four GPBR registers. */ void bootcount_store (ulong a) { - volatile ulong *save_addr = - (volatile ulong *)(AT91_BASE_SYS + AT91_BOOTCOUNT_ADDRESS); + at91_gpbr_t *gpbr = (at91_gpbr_t *) AT91_GPR_BASE; - *save_addr = (BOOTCOUNT_MAGIC & 0xffff0000) | (a & 0x0000ffff); + writel((BOOTCOUNT_MAGIC & 0xffff0000) | (a & 0x0000ffff), + &gpbr->reg[AT91_GPBR_INDEX_BOOTCOUNT]); } ulong bootcount_load (void) { - volatile ulong *save_addr = - (volatile ulong *)(AT91_BASE_SYS + AT91_BOOTCOUNT_ADDRESS); + at91_gpbr_t *gpbr = (at91_gpbr_t *) AT91_GPR_BASE; - if ((*save_addr & 0xffff0000) != (BOOTCOUNT_MAGIC & 0xffff0000)) + ulong val = readl(&gpbr->reg[AT91_GPBR_INDEX_BOOTCOUNT]); + if ((val & 0xffff0000) != (BOOTCOUNT_MAGIC & 0xffff0000)) return 0; else - return (*save_addr & 0x0000ffff); + return val & 0x0000ffff; } #endif /* CONFIG_BOOTCOUNT_LIMIT */ diff --git a/arch/arm/cpu/arm926ejs/kirkwood/cpu.c b/arch/arm/cpu/arm926ejs/kirkwood/cpu.c index 82c978bd93e..b4a4c0428f9 100644 --- a/arch/arm/cpu/arm926ejs/kirkwood/cpu.c +++ b/arch/arm/cpu/arm926ejs/kirkwood/cpu.c @@ -54,10 +54,11 @@ unsigned char get_random_hex(void) u8 outbuf[BUFLEN]; /* - * in case of 88F6281/88F6192 A0, + * in case of 88F6281/88F6282/88F6192 A0, * Bit7 need to reset to generate random values in KW_REG_UNDOC_0x1470 - * Soc reg offsets KW_REG_UNDOC_0x1470 and KW_REG_UNDOC_0x1478 are reserved regs and - * Does not have names at this moment (no errata available) + * Soc reg offsets KW_REG_UNDOC_0x1470 and KW_REG_UNDOC_0x1478 are + * reserved regs and does not have names at this moment + * (no errata available) */ writel(readl(KW_REG_UNDOC_0x1478) & ~(1 << 7), KW_REG_UNDOC_0x1478); for (i = 0; i < BUFLEN; i++) { @@ -271,20 +272,31 @@ static void kw_sysrst_check(void) #if defined(CONFIG_DISPLAY_CPUINFO) int print_cpuinfo(void) { - char *name = "Unknown"; + char *rev; + u16 devid = (readl(KW_REG_PCIE_DEVID) >> 16) & 0xffff; + u8 revid = readl(KW_REG_PCIE_REVID) & 0xff; - switch (readl(KW_REG_DEVICE_ID) & 0x03) { - case 1: - name = "88F6192_A0"; + if ((readl(KW_REG_DEVICE_ID) & 0x03) > 2) { + printf("Error.. %s:Unsupported Kirkwood SoC 88F%04x\n", __FUNCTION__, devid); + return -1; + } + + switch (revid) { + case 0: + rev = "Z0"; break; case 2: - name = "88F6281_A0"; + rev = "A0"; + break; + case 3: + rev = "A1"; break; default: - printf("SoC: Unsupported Kirkwood\n"); - return -1; + rev = "??"; + break; } - printf("SoC: Kirkwood %s\n", name); + + printf("SoC: Kirkwood 88F%04x_%s\n", devid, rev); return 0; } #endif /* CONFIG_DISPLAY_CPUINFO */ diff --git a/arch/arm/cpu/arm926ejs/kirkwood/dram.c b/arch/arm/cpu/arm926ejs/kirkwood/dram.c index 8f2a18af6b3..7439c87f681 100644 --- a/arch/arm/cpu/arm926ejs/kirkwood/dram.c +++ b/arch/arm/cpu/arm926ejs/kirkwood/dram.c @@ -23,8 +23,11 @@ */ #include <config.h> +#include <common.h> #include <asm/arch/kirkwood.h> +DECLARE_GLOBAL_DATA_PTR; + #define KW_REG_CPUCS_WIN_BAR(x) (KW_REGISTER(0x1500) + (x * 0x08)) #define KW_REG_CPUCS_WIN_SZ(x) (KW_REGISTER(0x1504) + (x * 0x08)) /* @@ -56,3 +59,38 @@ u32 kw_sdram_bs(enum memory_bank bank) result += 0x01000000; return result; } + +#ifndef CONFIG_SYS_BOARD_DRAM_INIT +int dram_init(void) +{ + int i; + + gd->ram_size = 0; + for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { + gd->bd->bi_dram[i].start = kw_sdram_bar(i); + gd->bd->bi_dram[i].size = kw_sdram_bs(i); + /* + * It is assumed that all memory banks are consecutive + * and without gaps. + * If the gap is found, ram_size will be reported for + * consecutive memory only + */ + if (gd->bd->bi_dram[i].start != gd->ram_size) + break; + + gd->ram_size += gd->bd->bi_dram[i].size; + + } + return 0; +} + +/* + * If this function is not defined here, + * board.c alters dram bank zero configuration defined above. + */ +void dram_init_banksize(void) +{ + dram_init(); +} +#endif /* CONFIG_SYS_BOARD_DRAM_INIT */ + diff --git a/arch/arm/cpu/arm926ejs/orion5x/cpu.c b/arch/arm/cpu/arm926ejs/orion5x/cpu.c index 260f88b46e0..1894b52fbf1 100644 --- a/arch/arm/cpu/arm926ejs/orion5x/cpu.c +++ b/arch/arm/cpu/arm926ejs/orion5x/cpu.c @@ -48,24 +48,34 @@ void reset_cpu(unsigned long ignored) } /* - * Window Size + * Compute Window Size field value from size expressed in bytes * Used with the Base register to set the address window size and location. * Must be programmed from LSB to MSB as sequence of ones followed by * sequence of zeros. The number of ones specifies the size of the window in - * 64 KByte granularity (e.g., a value of 0x00FF specifies 256 = 16 MByte). - * NOTE: A value of 0x0 specifies 64-KByte size. + * 64 KiB granularity (e.g., a value of 0x00FF specifies 256 = 16 MiB). + * NOTES: + * 1) A sizeval equal to 0x0 specifies 4 GiB. + * 2) A return value of 0x0 specifies 64 KiB. */ unsigned int orion5x_winctrl_calcsize(unsigned int sizeval) { - int i; - unsigned int j = 0; - u32 val = sizeval >> 1; - - for (i = 0; val >= 0x10000; i++) { - j |= (1 << i); - val = val >> 1; - } - return 0x0000ffff & j; + /* + * Calculate the number of 64 KiB blocks needed minus one (rounding up). + * For sizeval > 0 this is equivalent to: + * sizeval = (u32) ceil((double) sizeval / 65536.0) - 1 + */ + sizeval = (sizeval - 1) >> 16; + + /* + * Propagate 'one' bits to the right by 'oring' them. + * We need only treat bits 15-0. + */ + sizeval |= sizeval >> 1; /* 'Or' bit 15 onto bit 14 */ + sizeval |= sizeval >> 2; /* 'Or' bits 15-14 onto bits 13-12 */ + sizeval |= sizeval >> 4; /* 'Or' bits 15-12 onto bits 11-8 */ + sizeval |= sizeval >> 8; /* 'Or' bits 15-8 onto bits 7-0*/ + + return sizeval; } /* @@ -77,6 +87,17 @@ unsigned int orion5x_winctrl_calcsize(unsigned int sizeval) * * If remap function not used, remap_lo must be set as base * + * NOTES: + * + * 1) in order to avoid windows with inconsistent control and base values + * (which could prevent access to BOOTCS and hence execution from FLASH) + * always disable window before writing the base value then reenable it + * by writing the control value. + * + * 2) in order to avoid losing access to BOOTCS when disabling window 7, + * first configure window 6 for BOOTCS, then configure window 7 for BOOTCS, + * then configure windows 6 for its own target. + * * Reference Documentation: * Mbus-L to Mbus Bridge Registers Configuration. * (Sec 25.1 and 25.3 of Datasheet) @@ -86,57 +107,64 @@ int orion5x_config_adr_windows(void) struct orion5x_win_registers *winregs = (struct orion5x_win_registers *)ORION5X_CPU_WIN_BASE; - /* Window 0: PCIE MEM address space */ - writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_PCIE_MEM, - ORION5X_TARGET_PCIE, ORION5X_ATTR_PCIE_MEM, - ORION5X_WIN_ENABLE), &winregs[0].ctrl); +/* Disable window 0, configure it for its intended target, enable it. */ + writel(0, &winregs[0].ctrl); writel(ORION5X_ADR_PCIE_MEM, &winregs[0].base); writel(ORION5X_ADR_PCIE_MEM_REMAP_LO, &winregs[0].remap_lo); writel(ORION5X_ADR_PCIE_MEM_REMAP_HI, &winregs[0].remap_hi); - - /* Window 1: PCIE IO address space */ - writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_PCIE_IO, - ORION5X_TARGET_PCIE, ORION5X_ATTR_PCIE_IO, - ORION5X_WIN_ENABLE), &winregs[1].ctrl); + writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_PCIE_MEM, + ORION5X_TARGET_PCIE, ORION5X_ATTR_PCIE_MEM, + ORION5X_WIN_ENABLE), &winregs[0].ctrl); +/* Disable window 1, configure it for its intended target, enable it. */ + writel(0, &winregs[1].ctrl); writel(ORION5X_ADR_PCIE_IO, &winregs[1].base); writel(ORION5X_ADR_PCIE_IO_REMAP_LO, &winregs[1].remap_lo); writel(ORION5X_ADR_PCIE_IO_REMAP_HI, &winregs[1].remap_hi); - - /* Window 2: PCI MEM address space */ + writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_PCIE_IO, + ORION5X_TARGET_PCIE, ORION5X_ATTR_PCIE_IO, + ORION5X_WIN_ENABLE), &winregs[1].ctrl); +/* Disable window 2, configure it for its intended target, enable it. */ + writel(0, &winregs[2].ctrl); + writel(ORION5X_ADR_PCI_MEM, &winregs[2].base); writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_PCI_MEM, ORION5X_TARGET_PCI, ORION5X_ATTR_PCI_MEM, ORION5X_WIN_ENABLE), &winregs[2].ctrl); - writel(ORION5X_ADR_PCI_MEM, &winregs[2].base); - - /* Window 3: PCI IO address space */ +/* Disable window 3, configure it for its intended target, enable it. */ + writel(0, &winregs[3].ctrl); + writel(ORION5X_ADR_PCI_IO, &winregs[3].base); writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_PCI_IO, ORION5X_TARGET_PCI, ORION5X_ATTR_PCI_IO, ORION5X_WIN_ENABLE), &winregs[3].ctrl); - writel(ORION5X_ADR_PCI_IO, &winregs[3].base); - - /* Window 4: DEV_CS0 address space */ +/* Disable window 4, configure it for its intended target, enable it. */ + writel(0, &winregs[4].ctrl); + writel(ORION5X_ADR_DEV_CS0, &winregs[4].base); writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_DEV_CS0, ORION5X_TARGET_DEVICE, ORION5X_ATTR_DEV_CS0, ORION5X_WIN_ENABLE), &winregs[4].ctrl); - writel(ORION5X_ADR_DEV_CS0, &winregs[4].base); - - /* Window 5: DEV_CS1 address space */ +/* Disable window 5, configure it for its intended target, enable it. */ + writel(0, &winregs[5].ctrl); + writel(ORION5X_ADR_DEV_CS1, &winregs[5].base); writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_DEV_CS1, ORION5X_TARGET_DEVICE, ORION5X_ATTR_DEV_CS1, ORION5X_WIN_ENABLE), &winregs[5].ctrl); - writel(ORION5X_ADR_DEV_CS1, &winregs[5].base); - - /* Window 6: DEV_CS2 address space */ - writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_DEV_CS2, - ORION5X_TARGET_DEVICE, ORION5X_ATTR_DEV_CS2, +/* Disable window 6, configure it for FLASH, enable it. */ + writel(0, &winregs[6].ctrl); + writel(ORION5X_ADR_BOOTROM, &winregs[6].base); + writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_BOOTROM, + ORION5X_TARGET_DEVICE, ORION5X_ATTR_BOOTROM, ORION5X_WIN_ENABLE), &winregs[6].ctrl); - writel(ORION5X_ADR_DEV_CS2, &winregs[6].base); - - /* Window 7: BOOT Memory address space */ +/* Disable window 7, configure it for FLASH, enable it. */ + writel(0, &winregs[7].ctrl); + writel(ORION5X_ADR_BOOTROM, &winregs[7].base); writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_BOOTROM, ORION5X_TARGET_DEVICE, ORION5X_ATTR_BOOTROM, ORION5X_WIN_ENABLE), &winregs[7].ctrl); - writel(ORION5X_ADR_BOOTROM, &winregs[7].base); +/* Disable window 6, configure it for its intended target, enable it. */ + writel(0, &winregs[6].ctrl); + writel(ORION5X_ADR_DEV_CS2, &winregs[6].base); + writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_DEV_CS2, + ORION5X_TARGET_DEVICE, ORION5X_ATTR_DEV_CS2, + ORION5X_WIN_ENABLE), &winregs[6].ctrl); return 0; } @@ -265,6 +293,8 @@ int arch_misc_init(void) writel(ORION5X_MPP16_23, ORION5X_MPP_BASE+0x50); writel(ORION5X_GPIO_OUT_ENABLE, ORION5X_GPIO_BASE+0x04); + /* initialize timer */ + timer_init_r(); return 0; } #endif /* CONFIG_ARCH_MISC_INIT */ diff --git a/arch/arm/cpu/arm926ejs/orion5x/timer.c b/arch/arm/cpu/arm926ejs/orion5x/timer.c index 115448fa3f0..089ef47b371 100644 --- a/arch/arm/cpu/arm926ejs/orion5x/timer.c +++ b/arch/arm/cpu/arm926ejs/orion5x/timer.c @@ -173,9 +173,11 @@ int timer_init(void) cntmrctrl |= CTCR_ARM_TIMER_EN(UBOOT_CNTR); cntmrctrl |= CTCR_ARM_TIMER_AUTO_EN(UBOOT_CNTR); writel(cntmrctrl, CNTMR_CTRL_REG); + return 0; +} +void timer_init_r(void) +{ /* init the timestamp and lastdec value */ reset_timer_masked(); - - return 0; } diff --git a/arch/arm/cpu/arm926ejs/start.S b/arch/arm/cpu/arm926ejs/start.S index 16ee972f2b9..a960689e759 100644 --- a/arch/arm/cpu/arm926ejs/start.S +++ b/arch/arm/cpu/arm926ejs/start.S @@ -236,8 +236,8 @@ stack_setup: copy_loop: ldmia r0!, {r9-r10} /* copy from source address [r0] */ stmia r6!, {r9-r10} /* copy to target address [r1] */ - cmp r0, r2 /* until source end addreee [r2] */ - ble copy_loop + cmp r0, r2 /* until source end address [r2] */ + blo copy_loop #ifndef CONFIG_PRELOADER /* fix got entries */ @@ -341,8 +341,8 @@ relocate: /* relocate U-Boot to RAM */ copy_loop: ldmia r0!, {r3-r10} /* copy from source address [r0] */ stmia r1!, {r3-r10} /* copy to target address [r1] */ - cmp r0, r2 /* until source end addreee [r2] */ - ble copy_loop + cmp r0, r2 /* until source end address [r2] */ + blo copy_loop #endif /* CONFIG_SKIP_RELOCATE_UBOOT */ /* Set up the stack */ @@ -368,7 +368,7 @@ clear_bss: clbss_l:str r2, [r0] /* clear loop... */ add r0, r0, #4 cmp r0, r1 - ble clbss_l + blo clbss_l bl coloured_LED_init bl red_LED_on diff --git a/arch/arm/cpu/arm946es/start.S b/arch/arm/cpu/arm946es/start.S index 18ed0b2da41..4f062e5fffb 100644 --- a/arch/arm/cpu/arm946es/start.S +++ b/arch/arm/cpu/arm946es/start.S @@ -207,8 +207,8 @@ stack_setup: copy_loop: ldmia r0!, {r9-r10} /* copy from source address [r0] */ stmia r6!, {r9-r10} /* copy to target address [r1] */ - cmp r0, r2 /* until source end addreee [r2] */ - ble copy_loop + cmp r0, r2 /* until source end address [r2] */ + blo copy_loop #ifndef CONFIG_PRELOADER /* fix got entries */ @@ -309,8 +309,8 @@ relocate: /* relocate U-Boot to RAM */ copy_loop: ldmia r0!, {r3-r10} /* copy from source address [r0] */ stmia r1!, {r3-r10} /* copy to target address [r1] */ - cmp r0, r2 /* until source end addreee [r2] */ - ble copy_loop + cmp r0, r2 /* until source end address [r2] */ + blo copy_loop /* Set up the stack */ stack_setup: diff --git a/arch/arm/cpu/arm_intcm/start.S b/arch/arm/cpu/arm_intcm/start.S index b39fdc64c41..79ef517369f 100644 --- a/arch/arm/cpu/arm_intcm/start.S +++ b/arch/arm/cpu/arm_intcm/start.S @@ -205,8 +205,8 @@ stack_setup: copy_loop: ldmia r0!, {r9-r10} /* copy from source address [r0] */ stmia r6!, {r9-r10} /* copy to target address [r1] */ - cmp r0, r2 /* until source end addreee [r2] */ - ble copy_loop + cmp r0, r2 /* until source end address [r2] */ + blo copy_loop #ifndef CONFIG_PRELOADER /* fix got entries */ @@ -305,8 +305,8 @@ relocate: /* relocate U-Boot to RAM */ copy_loop: ldmia r0!, {r3-r10} /* copy from source address [r0] */ stmia r1!, {r3-r10} /* copy to target address [r1] */ - cmp r0, r2 /* until source end addreee [r2] */ - ble copy_loop + cmp r0, r2 /* until source end address [r2] */ + blo copy_loop /* Set up the stack */ stack_setup: @@ -327,7 +327,7 @@ clear_bss: clbss_l:str r2, [r0] /* clear loop... */ add r0, r0, #4 cmp r0, r1 - ble clbss_l + blo clbss_l ldr pc, _start_armboot diff --git a/arch/arm/cpu/armv7/Makefile b/arch/arm/cpu/armv7/Makefile index ae20299db73..7743fefdbea 100644 --- a/arch/arm/cpu/armv7/Makefile +++ b/arch/arm/cpu/armv7/Makefile @@ -27,6 +27,7 @@ LIB = $(obj)lib$(CPU).a START := start.o COBJS := cpu.o +COBJS += syslib.o SRCS := $(START:.o=.S) $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(COBJS)) @@ -44,4 +45,4 @@ include $(SRCTREE)/rules.mk sinclude $(obj).depend -#########################################################################
\ No newline at end of file +######################################################################### diff --git a/arch/arm/cpu/armv7/omap-common/Makefile b/arch/arm/cpu/armv7/omap-common/Makefile index caee7263b15..aedea7b95b9 100644 --- a/arch/arm/cpu/armv7/omap-common/Makefile +++ b/arch/arm/cpu/armv7/omap-common/Makefile @@ -28,7 +28,6 @@ LIB = $(obj)libomap-common.a SOBJS := reset.o COBJS := timer.o -COBJS += syslib.o SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) diff --git a/arch/arm/cpu/armv7/start.S b/arch/arm/cpu/armv7/start.S index f411c0f4f05..c392c5d9d61 100644 --- a/arch/arm/cpu/armv7/start.S +++ b/arch/arm/cpu/armv7/start.S @@ -209,8 +209,8 @@ stack_setup: copy_loop: ldmia r0!, {r9-r10} /* copy from source address [r0] */ stmia r6!, {r9-r10} /* copy to target address [r1] */ - cmp r0, r2 /* until source end addreee [r2] */ - ble copy_loop + cmp r0, r2 /* until source end address [r2] */ + blo copy_loop #ifndef CONFIG_PRELOADER /* fix got entries */ @@ -324,8 +324,8 @@ relocate: @ relocate U-Boot to RAM copy_loop: @ copy 32 bytes at a time ldmia r0!, {r3 - r10} @ copy from source address [r0] stmia r1!, {r3 - r10} @ copy to target address [r1] - cmp r0, r2 @ until source end addreee [r2] - ble copy_loop + cmp r0, r2 @ until source end address [r2] + blo copy_loop #endif /* CONFIG_SKIP_RELOCATE_UBOOT */ /* Set up the stack */ diff --git a/arch/arm/cpu/armv7/omap-common/syslib.c b/arch/arm/cpu/armv7/syslib.c index f9ed9a307b7..f9ed9a307b7 100644 --- a/arch/arm/cpu/armv7/omap-common/syslib.c +++ b/arch/arm/cpu/armv7/syslib.c diff --git a/arch/arm/cpu/ixp/start.S b/arch/arm/cpu/ixp/start.S index b2c8255141e..940d45d7328 100644 --- a/arch/arm/cpu/ixp/start.S +++ b/arch/arm/cpu/ixp/start.S @@ -330,8 +330,8 @@ stack_setup: copy_loop: ldmia r0!, {r9-r10} /* copy from source address [r0] */ stmia r6!, {r9-r10} /* copy to target address [r1] */ - cmp r0, r2 /* until source end addreee [r2] */ - ble copy_loop + cmp r0, r2 /* until source end address [r2] */ + blo copy_loop #ifndef CONFIG_PRELOADER /* fix got entries */ @@ -547,8 +547,8 @@ relocate: /* relocate U-Boot to RAM */ copy_loop: ldmia r0!, {r3-r10} /* copy from source address [r0] */ stmia r1!, {r3-r10} /* copy to target address [r1] */ - cmp r0, r2 /* until source end addreee [r2] */ - ble copy_loop + cmp r0, r2 /* until source end address [r2] */ + blo copy_loop #endif /* CONFIG_SKIP_RELOCATE_UBOOT */ /* Set up the stack */ @@ -570,7 +570,7 @@ clear_bss: clbss_l:str r2, [r0] /* clear loop... */ add r0, r0, #4 cmp r0, r1 - ble clbss_l + blo clbss_l ldr pc, _start_armboot diff --git a/arch/arm/cpu/lh7a40x/start.S b/arch/arm/cpu/lh7a40x/start.S index 002116a4010..b8cf1b8b379 100644 --- a/arch/arm/cpu/lh7a40x/start.S +++ b/arch/arm/cpu/lh7a40x/start.S @@ -219,8 +219,8 @@ stack_setup: copy_loop: ldmia r0!, {r9-r10} /* copy from source address [r0] */ stmia r6!, {r9-r10} /* copy to target address [r1] */ - cmp r0, r2 /* until source end addreee [r2] */ - ble copy_loop + cmp r0, r2 /* until source end address [r2] */ + blo copy_loop #ifndef CONFIG_PRELOADER /* fix got entries */ @@ -341,9 +341,8 @@ relocate: /* relocate U-Boot to RAM */ copy_loop: ldmia r0!, {r3-r10} /* copy from source address [r0] */ stmia r1!, {r3-r10} /* copy to target address [r1] */ - cmp r0, r2 /* until source end addreee [r2] */ - blt copy_loop /* a 'ble' here actually copies */ - /* four bytes of bss */ + cmp r0, r2 /* until source end address [r2] */ + blo copy_loop #endif /* CONFIG_SKIP_RELOCATE_UBOOT */ /* Set up the stack */ @@ -367,7 +366,7 @@ clear_bss: clbss_l:str r2, [r0] /* clear loop... */ add r0, r0, #4 cmp r0, r1 - ble clbss_l + blo clbss_l ldr pc, _start_armboot diff --git a/arch/arm/cpu/pxa/start.S b/arch/arm/cpu/pxa/start.S index 064ddbcf3fb..cfb94112d0a 100644 --- a/arch/arm/cpu/pxa/start.S +++ b/arch/arm/cpu/pxa/start.S @@ -204,8 +204,8 @@ stack_setup: copy_loop: ldmia r0!, {r9-r10} /* copy from source address [r0] */ stmia r6!, {r9-r10} /* copy to target address [r1] */ - cmp r0, r2 /* until source end addreee [r2] */ - ble copy_loop + cmp r0, r2 /* until source end address [r2] */ + blo copy_loop #ifndef CONFIG_PRELOADER /* fix got entries */ @@ -310,7 +310,7 @@ copy_loop: ldmia r0!, {r3-r10} /* copy from source address [r0] */ stmia r1!, {r3-r10} /* copy to target address [r1] */ cmp r0, r2 /* until source end address [r2] */ - ble copy_loop + blo copy_loop #endif /* !CONFIG_SKIP_RELOCATE_UBOOT */ /* Set up the stack */ @@ -337,7 +337,7 @@ clear_bss: clbss_l:str r2, [r0] /* clear loop... */ add r0, r0, #4 cmp r0, r1 - ble clbss_l + blo clbss_l #endif ldr pc, _start_armboot diff --git a/arch/arm/cpu/s3c44b0/start.S b/arch/arm/cpu/s3c44b0/start.S index e1ab5ccb362..c5a67dc66d6 100644 --- a/arch/arm/cpu/s3c44b0/start.S +++ b/arch/arm/cpu/s3c44b0/start.S @@ -191,8 +191,8 @@ stack_setup: copy_loop: ldmia r0!, {r9-r10} /* copy from source address [r0] */ stmia r6!, {r9-r10} /* copy to target address [r1] */ - cmp r0, r2 /* until source end addreee [r2] */ - ble copy_loop + cmp r0, r2 /* until source end address [r2] */ + blo copy_loop #ifndef CONFIG_PRELOADER /* fix got entries */ @@ -225,7 +225,7 @@ vector_copy_loop: ldmia r0!, {r3-r10} stmia r1!, {r3-r10} cmp r0, r2 - ble vector_copy_loop + blo vector_copy_loop #endif /* #ifndef CONFIG_SKIP_RELOCATE_UBOOT */ clear_bss: @@ -310,8 +310,8 @@ relocate: /* relocate U-Boot to RAM */ copy_loop: ldmia r0!, {r3-r10} /* copy from source address [r0] */ stmia r1!, {r3-r10} /* copy to target address [r1] */ - cmp r0, r2 /* until source end addreee [r2] */ - ble copy_loop + cmp r0, r2 /* until source end address [r2] */ + blo copy_loop /* now copy to sram the interrupt vector @@ -324,7 +324,7 @@ vector_copy_loop: ldmia r0!, {r3-r10} stmia r1!, {r3-r10} cmp r0, r2 - ble vector_copy_loop + blo vector_copy_loop #endif /* CONFIG_SKIP_RELOCATE_UBOOT */ /* Set up the stack */ diff --git a/arch/arm/cpu/sa1100/start.S b/arch/arm/cpu/sa1100/start.S index 4730e5a9ab0..d1262ada2c7 100644 --- a/arch/arm/cpu/sa1100/start.S +++ b/arch/arm/cpu/sa1100/start.S @@ -195,8 +195,8 @@ stack_setup: copy_loop: ldmia r0!, {r9-r10} /* copy from source address [r0] */ stmia r6!, {r9-r10} /* copy to target address [r1] */ - cmp r0, r2 /* until source end addreee [r2] */ - ble copy_loop + cmp r0, r2 /* until source end address [r2] */ + blo copy_loop #ifndef CONFIG_PRELOADER /* fix got entries */ @@ -293,8 +293,8 @@ relocate: /* relocate U-Boot to RAM */ copy_loop: ldmia r0!, {r3-r10} /* copy from source address [r0] */ stmia r1!, {r3-r10} /* copy to target address [r1] */ - cmp r0, r2 /* until source end addreee [r2] */ - ble copy_loop + cmp r0, r2 /* until source end address [r2] */ + blo copy_loop #endif /* CONFIG_SKIP_RELOCATE_UBOOT */ /* Set up the stack */ @@ -316,7 +316,7 @@ clear_bss: clbss_l:str r2, [r0] /* clear loop... */ add r0, r0, #4 cmp r0, r1 - ble clbss_l + blo clbss_l ldr pc, _start_armboot diff --git a/arch/arm/include/asm/arch-arm925t/sizes.h b/arch/arm/include/asm/arch-arm925t/sizes.h deleted file mode 100644 index 7319bd92276..00000000000 --- a/arch/arm/include/asm/arch-arm925t/sizes.h +++ /dev/null @@ -1,50 +0,0 @@ -/* - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ -/* DO NOT EDIT!! - this file automatically generated - * from .s file by awk -f s2h.awk - */ -/* Size defintions - * Copyright (C) ARM Limited 1998. All rights reserved. - */ - -#ifndef __sizes_h -#define __sizes_h 1 - -/* handy sizes */ -#define SZ_1K 0x00000400 -#define SZ_4K 0x00001000 -#define SZ_8K 0x00002000 -#define SZ_16K 0x00004000 -#define SZ_64K 0x00010000 -#define SZ_128K 0x00020000 -#define SZ_256K 0x00040000 -#define SZ_512K 0x00080000 - -#define SZ_1M 0x00100000 -#define SZ_2M 0x00200000 -#define SZ_4M 0x00400000 -#define SZ_8M 0x00800000 -#define SZ_16M 0x01000000 -#define SZ_32M 0x02000000 -#define SZ_64M 0x04000000 -#define SZ_128M 0x08000000 -#define SZ_256M 0x10000000 -#define SZ_512M 0x20000000 - -#define SZ_1G 0x40000000 -#define SZ_2G 0x80000000 - -#endif /* __sizes_h */ diff --git a/arch/arm/include/asm/arch-arm926ejs/sizes.h b/arch/arm/include/asm/arch-arm926ejs/sizes.h deleted file mode 100644 index ef0b99b9467..00000000000 --- a/arch/arm/include/asm/arch-arm926ejs/sizes.h +++ /dev/null @@ -1,51 +0,0 @@ -/* - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA0 2111-1307 - * USA - */ -/* DO NOT EDIT!! - this file automatically generated - * from .s file by awk -f s2h.awk - */ -/* Size defintions - * Copyright (C) ARM Limited 1998. All rights reserved. - */ - -#ifndef __sizes_h -#define __sizes_h 1 - -/* handy sizes */ -#define SZ_1K 0x00000400 -#define SZ_4K 0x00001000 -#define SZ_8K 0x00002000 -#define SZ_16K 0x00004000 -#define SZ_64K 0x00010000 -#define SZ_128K 0x00020000 -#define SZ_256K 0x00040000 -#define SZ_512K 0x00080000 - -#define SZ_1M 0x00100000 -#define SZ_2M 0x00200000 -#define SZ_4M 0x00400000 -#define SZ_8M 0x00800000 -#define SZ_16M 0x01000000 -#define SZ_32M 0x02000000 -#define SZ_64M 0x04000000 -#define SZ_128M 0x08000000 -#define SZ_256M 0x10000000 -#define SZ_512M 0x20000000 - -#define SZ_1G 0x40000000 -#define SZ_2G 0x80000000 - -#endif /* __sizes_h */ diff --git a/arch/arm/include/asm/arch-armv7/sysctrl.h b/arch/arm/include/asm/arch-armv7/sysctrl.h new file mode 100644 index 00000000000..4e451675fc1 --- /dev/null +++ b/arch/arm/include/asm/arch-armv7/sysctrl.h @@ -0,0 +1,70 @@ +/* + * (C) Copyright 2010 Linaro + * Matt Waddel, <matt.waddel@linaro.org> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef _SYSCTRL_H_ +#define _SYSCTRL_H_ + +/* System controller (SP810) register definitions */ +#define SP810_TIMER0_ENSEL (1 << 15) +#define SP810_TIMER1_ENSEL (1 << 17) +#define SP810_TIMER2_ENSEL (1 << 19) +#define SP810_TIMER3_ENSEL (1 << 21) + +struct sysctrl { + u32 scctrl; /* 0x000 */ + u32 scsysstat; + u32 scimctrl; + u32 scimstat; + u32 scxtalctrl; + u32 scpllctrl; + u32 scpllfctrl; + u32 scperctrl0; + u32 scperctrl1; + u32 scperen; + u32 scperdis; + u32 scperclken; + u32 scperstat; + u32 res1[0x006]; + u32 scflashctrl; /* 0x04c */ + u32 res2[0x3a4]; + u32 scsysid0; /* 0xee0 */ + u32 scsysid1; + u32 scsysid2; + u32 scsysid3; + u32 scitcr; + u32 scitir0; + u32 scitir1; + u32 scitor; + u32 sccntctrl; + u32 sccntdata; + u32 sccntstep; + u32 res3[0x32]; + u32 scperiphid0; /* 0xfe0 */ + u32 scperiphid1; + u32 scperiphid2; + u32 scperiphid3; + u32 scpcellid0; + u32 scpcellid1; + u32 scpcellid2; + u32 scpcellid3; +}; +#endif /* _SYSCTRL_H_ */ diff --git a/board/freescale/mx51evk/mx51evk.h b/arch/arm/include/asm/arch-armv7/systimer.h index 2854e71e8d2..e745e375094 100644 --- a/board/freescale/mx51evk/mx51evk.h +++ b/arch/arm/include/asm/arch-armv7/systimer.h @@ -1,5 +1,6 @@ /* - * (C) Copyright 2009 Freescale Semiconductor, Inc. + * (C) Copyright 2010 Linaro + * Matt Waddel, <matt.waddel@linaro.org> * * See file CREDITS for list of people who contributed to this * project. @@ -19,32 +20,31 @@ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ +#ifndef _SYSTIMER_H_ +#define _SYSTIMER_H_ -#ifndef __BOARD_FREESCALE_MX51_EVK_H__ -#define __BOARD_FREESCALE_MX51_EVK_H__ +/* AMBA timer register base address */ +#define SYSTIMER_BASE 0x10011000 -#ifndef __ASSEMBLY__ -struct io_board_ctrl { - u16 led_ctrl; /* 0x00 */ - u16 resv1[0x03]; - u16 sb_stat; /* 0x08 */ - u16 resv2[0x03]; - u16 int_stat; /* 0x10 */ - u16 resv3[0x07]; - u16 int_rest; /* 0x20 */ - u16 resv4[0x0B]; - u16 int_mask; /* 0x38 */ - u16 resv5[0x03]; - u16 id1; /* 0x40 */ - u16 resv6[0x03]; - u16 id2; /* 0x48 */ - u16 resv7[0x03]; - u16 version; /* 0x50 */ - u16 resv8[0x03]; - u16 id3; /* 0x58 */ - u16 resv9[0x03]; - u16 sw_reset; /* 0x60 */ -}; -#endif +#define SYSHZ_CLOCK 1000000 /* Timers -> 1Mhz */ +#define SYSTIMER_RELOAD 0xFFFFFFFF +#define SYSTIMER_EN (1 << 7) +#define SYSTIMER_32BIT (1 << 1) -#endif +struct systimer { + u32 timer0load; /* 0x00 */ + u32 timer0value; + u32 timer0control; + u32 timer0intclr; + u32 timer0ris; + u32 timer0mis; + u32 timer0bgload; + u32 timer1load; /* 0x20 */ + u32 timer1value; + u32 timer1control; + u32 timer1intclr; + u32 timer1ris; + u32 timer1mis; + u32 timer1bgload; +}; +#endif /* _SYSTIMER_H_ */ diff --git a/arch/arm/include/asm/arch-armv7/wdt.h b/arch/arm/include/asm/arch-armv7/wdt.h new file mode 100644 index 00000000000..ee74c38c193 --- /dev/null +++ b/arch/arm/include/asm/arch-armv7/wdt.h @@ -0,0 +1,55 @@ +/* + * (C) Copyright 2010 + * Matt Waddel, <matt.waddel@linaro.org> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef _WDT_H_ +#define _WDT_H_ + +/* Watchdog timer (SP805) register base address */ +#define WDT_BASE 0x100E5000 + +#define WDT_EN 0x2 +#define WDT_RESET_LOAD 0x0 + +struct wdt { + u32 wdogload; /* 0x000 */ + u32 wdogvalue; + u32 wdogcontrol; + u32 wdogintclr; + u32 wdogris; + u32 wdogmis; + u32 res1[0x2F9]; + u32 wdoglock; /* 0xC00 */ + u32 res2[0xBE]; + u32 wdogitcr; /* 0xF00 */ + u32 wdogitop; + u32 res3[0x35]; + u32 wdogperiphid0; /* 0xFE0 */ + u32 wdogperiphid1; + u32 wdogperiphid2; + u32 wdogperiphid3; + u32 wdogpcellid0; + u32 wdogpcellid1; + u32 wdogpcellid2; + u32 wdogpcellid3; +}; + +#endif /* _WDT_H_ */ diff --git a/arch/arm/include/asm/arch-at91/at91_emac.h b/arch/arm/include/asm/arch-at91/at91_emac.h index 45ae33311e1..0e2ff78f421 100644 --- a/arch/arm/include/asm/arch-at91/at91_emac.h +++ b/arch/arm/include/asm/arch-at91/at91_emac.h @@ -61,7 +61,7 @@ typedef struct at91_emac { u32 reserved2[3]; u32 hsh; u32 hsl; - u32 sh1l; + u32 sa1l; u32 sa1h; u32 sa2l; u32 sa2h; diff --git a/arch/arm/include/asm/arch-kirkwood/cpu.h b/arch/arm/include/asm/arch-kirkwood/cpu.h index b3022a37801..d28c51a9b6b 100644 --- a/arch/arm/include/asm/arch-kirkwood/cpu.h +++ b/arch/arm/include/asm/arch-kirkwood/cpu.h @@ -35,6 +35,8 @@ #define KWGBE_PORT_SERIAL_CONTROL1_REG(_x) \ ((_x ? KW_EGIGA0_BASE : KW_EGIGA1_BASE) + 0x44c) +#define KW_REG_PCIE_DEVID (KW_REG_PCIE_BASE + 0x00) +#define KW_REG_PCIE_REVID (KW_REG_PCIE_BASE + 0x08) #define KW_REG_DEVICE_ID (KW_MPP_BASE + 0x34) #define KW_REG_SYSRST_CNT (KW_MPP_BASE + 0x50) #define SYSRST_CNT_1SEC_VAL (25*1000000) diff --git a/arch/arm/include/asm/arch-mx31/mx31-regs.h b/arch/arm/include/asm/arch-mx31/mx31-regs.h index d72585c8a01..f05e743d761 100644 --- a/arch/arm/include/asm/arch-mx31/mx31-regs.h +++ b/arch/arm/include/asm/arch-mx31/mx31-regs.h @@ -57,6 +57,14 @@ struct clock_control_regs { u32 pdr2; }; +/* GPIO Registers */ +struct gpio_regs { + u32 gpio_dr; + u32 gpio_dir; + u32 gpio_psr; +}; + + /* Bit definitions for RCSR register in CCM */ #define CCM_RCSR_NF16B (1 << 31) #define CCM_RCSR_NFMS (1 << 30) @@ -153,9 +161,9 @@ struct clock_control_regs { /* * GPIO */ -#define GPIO1_BASE 0x53FCC000 -#define GPIO2_BASE 0x53FD0000 -#define GPIO3_BASE 0x53FA4000 +#define GPIO1_BASE_ADDR 0x53FCC000 +#define GPIO2_BASE_ADDR 0x53FD0000 +#define GPIO3_BASE_ADDR 0x53FA4000 #define GPIO_DR 0x00000000 /* data register */ #define GPIO_GDIR 0x00000004 /* direction register */ #define GPIO_PSR 0x00000008 /* pad status register */ diff --git a/arch/arm/include/asm/arch-mx31/mx31.h b/arch/arm/include/asm/arch-mx31/mx31.h index f702d260f11..5a5aa114a74 100644 --- a/arch/arm/include/asm/arch-mx31/mx31.h +++ b/arch/arm/include/asm/arch-mx31/mx31.h @@ -28,31 +28,6 @@ extern u32 mx31_get_ipg_clk(void); #define imx_get_uartclk mx31_get_ipg_clk extern void mx31_gpio_mux(unsigned long mode); -enum mx31_gpio_direction { - MX31_GPIO_DIRECTION_IN, - MX31_GPIO_DIRECTION_OUT, -}; - -#ifdef CONFIG_MX31_GPIO -extern int mx31_gpio_direction(unsigned int gpio, - enum mx31_gpio_direction direction); -extern void mx31_gpio_set(unsigned int gpio, unsigned int value); -extern int mx31_gpio_get(unsigned int gpio); -#else -static inline int mx31_gpio_direction(unsigned int gpio, - enum mx31_gpio_direction direction) -{ - return 1; -} -static inline int mx31_gpio_get(unsigned int gpio) -{ - return 1; -} -static inline void mx31_gpio_set(unsigned int gpio, unsigned int value) -{ -} -#endif - void mx31_uart1_hw_init(void); void mx31_spi2_hw_init(void); diff --git a/arch/arm/include/asm/arch-mx51/imx-regs.h b/arch/arm/include/asm/arch-mx51/imx-regs.h index 3887d3cec48..3ddda401f31 100644 --- a/arch/arm/include/asm/arch-mx51/imx-regs.h +++ b/arch/arm/include/asm/arch-mx51/imx-regs.h @@ -23,9 +23,6 @@ #ifndef __ASM_ARCH_MXC_MX51_H__ #define __ASM_ARCH_MXC_MX51_H__ -#define __REG(x) (*((volatile u32 *)(x))) -#define __REG16(x) (*((volatile u16 *)(x))) -#define __REG8(x) (*((volatile u8 *)(x))) /* * IRAM */ @@ -207,7 +204,12 @@ #define BOARD_REV_1_0 0x0 #define BOARD_REV_2_0 0x1 -#ifndef __ASSEMBLY__ +#if !(defined(__KERNEL_STRICT_NAMES) || defined(__ASSEMBLY__)) +#include <asm/types.h> + +#define __REG(x) (*((volatile u32 *)(x))) +#define __REG16(x) (*((volatile u16 *)(x))) +#define __REG8(x) (*((volatile u8 *)(x))) struct clkctl { u32 ccr; @@ -256,6 +258,22 @@ struct weim { u32 cswcr2; }; +/* GPIO Registers */ +struct gpio_regs { + u32 gpio_dr; + u32 gpio_dir; + u32 gpio_psr; +}; + +/* System Reset Controller (SRC) */ +struct src { + u32 scr; + u32 sbmr; + u32 srsr; + u32 reserved1[2]; + u32 sisr; + u32 simr; +}; #endif /* __ASSEMBLER__*/ #endif /* __ASM_ARCH_MXC_MX51_H__ */ diff --git a/arch/arm/include/asm/arch-mx51/mx51_pins.h b/arch/arm/include/asm/arch-mx51/mx51_pins.h index ca26f4166b3..b44ff252bfe 100644 --- a/arch/arm/include/asm/arch-mx51/mx51_pins.h +++ b/arch/arm/include/asm/arch-mx51/mx51_pins.h @@ -368,6 +368,50 @@ enum iomux_pins { MX51_PIN_GPIO1_7 = _MXC_BUILD_GPIO_PIN(0, 7, 0, 0x3E4, 0x810), MX51_PIN_GPIO1_8 = _MXC_BUILD_GPIO_PIN(0, 8, 0, 0x3E8, 0x814), MX51_PIN_GPIO1_9 = _MXC_BUILD_GPIO_PIN(0, 9, 0, 0x3EC, 0x818), + + /* The following are PADS used for drive strength */ + + MX51_PIN_CTL_GRP_DDRPKS = _MXC_BUILD_NON_GPIO_PIN(0, 0x820), + MX51_PIN_CTL_GRP_PKEDDR = _MXC_BUILD_NON_GPIO_PIN(0, 0x838), + MX51_PIN_CTL_GRP_PKEADDR = _MXC_BUILD_NON_GPIO_PIN(0, 0x890), + MX51_PIN_CTL_GRP_DDRAPKS = _MXC_BUILD_NON_GPIO_PIN(0, 0x87C), + MX51_PIN_CTL_GRP_DDRAPUS = _MXC_BUILD_NON_GPIO_PIN(0, 0x84C), + MX51_PIN_CTL_GRP_DDRPUS = _MXC_BUILD_NON_GPIO_PIN(0, 0x884), + MX51_PIN_CTL_GRP_HYSDDR0 = _MXC_BUILD_NON_GPIO_PIN(0, 0x85C), + MX51_PIN_CTL_GRP_HYSDDR1 = _MXC_BUILD_NON_GPIO_PIN(0, 0x864), + MX51_PIN_CTL_GRP_HYSDDR2 = _MXC_BUILD_NON_GPIO_PIN(0, 0x86C), + MX51_PIN_CTL_GRP_HYSDDR3 = _MXC_BUILD_NON_GPIO_PIN(0, 0x874), + MX51_PIN_CTL_GRP_DDR_SR_B0 = _MXC_BUILD_NON_GPIO_PIN(0, 0x878), + MX51_PIN_CTL_GRP_DDR_SR_B1 = _MXC_BUILD_NON_GPIO_PIN(0, 0x880), + MX51_PIN_CTL_GRP_DDR_SR_B2 = _MXC_BUILD_NON_GPIO_PIN(0, 0x88C), + MX51_PIN_CTL_GRP_DDR_SR_B4 = _MXC_BUILD_NON_GPIO_PIN(0, 0x89C), + MX51_PIN_CTL_GRP_DRAM_B0 = _MXC_BUILD_NON_GPIO_PIN(0, 0x8A4), + MX51_PIN_CTL_GRP_DRAM_B1 = _MXC_BUILD_NON_GPIO_PIN(0, 0x8AC), + MX51_PIN_CTL_GRP_DRAM_B2 = _MXC_BUILD_NON_GPIO_PIN(0, 0x8B8), + MX51_PIN_CTL_GRP_DRAM_B4 = _MXC_BUILD_NON_GPIO_PIN(0, 0x82C), + MX51_PIN_CTL_GRP_INMODE1 = _MXC_BUILD_NON_GPIO_PIN(0, 0x8A0), + MX51_PIN_CTL_GRP_DDR_SR_A0 = _MXC_BUILD_NON_GPIO_PIN(0, 0x8B0), + MX51_PIN_CTL_GRP_EMI_DS5 = _MXC_BUILD_NON_GPIO_PIN(0, 0x8B4), + MX51_PIN_CTL_GRP_DDR_SR_A1 = _MXC_BUILD_NON_GPIO_PIN(0, 0x8BC), + MX51_PIN_CTL_GRP_DDR_A0 = _MXC_BUILD_NON_GPIO_PIN(0, 0x83C), + MX51_PIN_CTL_GRP_DDR_A1 = _MXC_BUILD_NON_GPIO_PIN(0, 0x848), + MX51_PIN_CTL_GRP_DISP_PKE0 = _MXC_BUILD_NON_GPIO_PIN(0, 0x868), + MX51_PIN_CTL_DRAM_RAS = _MXC_BUILD_NON_GPIO_PIN(0, 0x4A4), + MX51_PIN_CTL_DRAM_CAS = _MXC_BUILD_NON_GPIO_PIN(0, 0x4A8), + MX51_PIN_CTL_DRAM_SDWE = _MXC_BUILD_NON_GPIO_PIN(0, 0x4Ac), + MX51_PIN_CTL_DRAM_SDCKE0 = _MXC_BUILD_NON_GPIO_PIN(0, 0x4B0), + MX51_PIN_CTL_DRAM_SDCKE1 = _MXC_BUILD_NON_GPIO_PIN(0, 0x4B4), + MX51_PIN_CTL_DRAM_SDCLK = _MXC_BUILD_NON_GPIO_PIN(0, 0x4B8), + MX51_PIN_CTL_DRAM_SDQS0 = _MXC_BUILD_NON_GPIO_PIN(0, 0x4BC), + MX51_PIN_CTL_DRAM_SDQS1 = _MXC_BUILD_NON_GPIO_PIN(0, 0x4C0), + MX51_PIN_CTL_DRAM_SDQS2 = _MXC_BUILD_NON_GPIO_PIN(0, 0x4C4), + MX51_PIN_CTL_DRAM_SDQS3 = _MXC_BUILD_NON_GPIO_PIN(0, 0x4C8), + MX51_PIN_CTL_DRAM_CS0 = _MXC_BUILD_NON_GPIO_PIN(0, 0x4CC), + MX51_PIN_CTL_DRAM_CS1 = _MXC_BUILD_NON_GPIO_PIN(0, 0x4D0), + MX51_PIN_CTL_DRAM_DQM0 = _MXC_BUILD_NON_GPIO_PIN(0, 0x4D4), + MX51_PIN_CTL_DRAM_DQM1 = _MXC_BUILD_NON_GPIO_PIN(0, 0x4D8), + MX51_PIN_CTL_DRAM_DQM2 = _MXC_BUILD_NON_GPIO_PIN(0, 0x4DC), + MX51_PIN_CTL_DRAM_DQM3 = _MXC_BUILD_NON_GPIO_PIN(0, 0x4E0), }; #endif /* __ASSEMBLY__ */ diff --git a/arch/arm/include/asm/arch-mx51/sys_proto.h b/arch/arm/include/asm/arch-mx51/sys_proto.h index bf500a8b325..f687503cada 100644 --- a/arch/arm/include/asm/arch-mx51/sys_proto.h +++ b/arch/arm/include/asm/arch-mx51/sys_proto.h @@ -26,5 +26,6 @@ u32 get_cpu_rev(void); #define is_soc_rev(rev) ((get_cpu_rev() & 0xFF) - rev) +void sdelay(unsigned long); #endif diff --git a/arch/arm/include/asm/arch-omap/sizes.h b/arch/arm/include/asm/arch-omap/sizes.h deleted file mode 100644 index f8d92ca1204..00000000000 --- a/arch/arm/include/asm/arch-omap/sizes.h +++ /dev/null @@ -1,52 +0,0 @@ -/* - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ -/* DO NOT EDIT!! - this file automatically generated - * from .s file by awk -f s2h.awk - */ -/* Size defintions - * Copyright (C) ARM Limited 1998. All rights reserved. - */ - -#ifndef __sizes_h -#define __sizes_h 1 - -/* handy sizes */ -#define SZ_1K 0x00000400 -#define SZ_4K 0x00001000 -#define SZ_8K 0x00002000 -#define SZ_16K 0x00004000 -#define SZ_64K 0x00010000 -#define SZ_128K 0x00020000 -#define SZ_256K 0x00040000 -#define SZ_512K 0x00080000 - -#define SZ_1M 0x00100000 -#define SZ_2M 0x00200000 -#define SZ_4M 0x00400000 -#define SZ_8M 0x00800000 -#define SZ_16M 0x01000000 -#define SZ_32M 0x02000000 -#define SZ_64M 0x04000000 -#define SZ_128M 0x08000000 -#define SZ_256M 0x10000000 -#define SZ_512M 0x20000000 - -#define SZ_1G 0x40000000 -#define SZ_2G 0x80000000 - -#endif - -/* END */ diff --git a/arch/arm/include/asm/arch-omap24xx/omap2420.h b/arch/arm/include/asm/arch-omap24xx/omap2420.h index 0c11beccf68..60324196414 100644 --- a/arch/arm/include/asm/arch-omap24xx/omap2420.h +++ b/arch/arm/include/asm/arch-omap24xx/omap2420.h @@ -25,7 +25,7 @@ #ifndef _OMAP2420_SYS_H_ #define _OMAP2420_SYS_H_ -#include <asm/arch/sizes.h> +#include <asm/sizes.h> /* * 2420 specific Section diff --git a/arch/arm/include/asm/arch-omap24xx/sizes.h b/arch/arm/include/asm/arch-omap24xx/sizes.h deleted file mode 100644 index aaba18f1507..00000000000 --- a/arch/arm/include/asm/arch-omap24xx/sizes.h +++ /dev/null @@ -1,49 +0,0 @@ -/* - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ -/* Size defintions - * Copyright (C) ARM Limited 1998. All rights reserved. - */ - -#ifndef __sizes_h -#define __sizes_h 1 - -/* handy sizes */ -#define SZ_1K 0x00000400 -#define SZ_4K 0x00001000 -#define SZ_8K 0x00002000 -#define SZ_16K 0x00004000 -#define SZ_32K 0x00008000 -#define SZ_64K 0x00010000 -#define SZ_128K 0x00020000 -#define SZ_256K 0x00040000 -#define SZ_512K 0x00080000 - -#define SZ_1M 0x00100000 -#define SZ_2M 0x00200000 -#define SZ_4M 0x00400000 -#define SZ_8M 0x00800000 -#define SZ_16M 0x01000000 -#define SZ_31M 0x01F00000 -#define SZ_32M 0x02000000 -#define SZ_64M 0x04000000 -#define SZ_128M 0x08000000 -#define SZ_256M 0x10000000 -#define SZ_512M 0x20000000 - -#define SZ_1G 0x40000000 -#define SZ_2G 0x80000000 - -#endif /* __sizes_h */ diff --git a/arch/arm/include/asm/arch-orion5x/cpu.h b/arch/arm/include/asm/arch-orion5x/cpu.h index 6ce02a92125..c84efaf02bd 100644 --- a/arch/arm/include/asm/arch-orion5x/cpu.h +++ b/arch/arm/include/asm/arch-orion5x/cpu.h @@ -255,5 +255,6 @@ void reset_cpu(unsigned long ignored); u32 orion5x_device_id(void); u32 orion5x_device_rev(void); unsigned int orion5x_winctrl_calcsize(unsigned int sizeval); +void timer_init_r(void); #endif /* __ASSEMBLY__ */ #endif /* _ORION5X_CPU_H */ diff --git a/arch/arm/include/asm/sizes.h b/arch/arm/include/asm/sizes.h index f8d92ca1204..b0b4f6af618 100644 --- a/arch/arm/include/asm/sizes.h +++ b/arch/arm/include/asm/sizes.h @@ -13,9 +13,6 @@ * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ -/* DO NOT EDIT!! - this file automatically generated - * from .s file by awk -f s2h.awk - */ /* Size defintions * Copyright (C) ARM Limited 1998. All rights reserved. */ @@ -28,6 +25,7 @@ #define SZ_4K 0x00001000 #define SZ_8K 0x00002000 #define SZ_16K 0x00004000 +#define SZ_32K 0x00008000 #define SZ_64K 0x00010000 #define SZ_128K 0x00020000 #define SZ_256K 0x00040000 @@ -38,6 +36,7 @@ #define SZ_4M 0x00400000 #define SZ_8M 0x00800000 #define SZ_16M 0x01000000 +#define SZ_31M 0x01F00000 #define SZ_32M 0x02000000 #define SZ_64M 0x04000000 #define SZ_128M 0x08000000 diff --git a/board/Marvell/guruplug/guruplug.c b/board/Marvell/guruplug/guruplug.c index c028a53bcbf..4df4e9b2604 100644 --- a/board/Marvell/guruplug/guruplug.c +++ b/board/Marvell/guruplug/guruplug.c @@ -108,17 +108,6 @@ int board_init(void) return 0; } -int dram_init(void) -{ - int i; - - for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { - gd->bd->bi_dram[i].start = kw_sdram_bar(i); - gd->bd->bi_dram[i].size = kw_sdram_bs(i); - } - return 0; -} - #ifdef CONFIG_RESET_PHY_R void mv_phy_88e1121_init(char *name) { diff --git a/board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.c b/board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.c index c959bf879e9..93d1400be49 100644 --- a/board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.c +++ b/board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.c @@ -110,17 +110,6 @@ int board_init(void) return 0; } -int dram_init(void) -{ - int i; - - for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { - gd->bd->bi_dram[i].start = kw_sdram_bar(i); - gd->bd->bi_dram[i].size = kw_sdram_bs(i); - } - return 0; -} - #ifdef CONFIG_MV88E61XX_SWITCH void reset_phy(void) { diff --git a/board/Marvell/openrd_base/openrd_base.c b/board/Marvell/openrd_base/openrd_base.c index c00a08aeab3..d006b2ddf7d 100644 --- a/board/Marvell/openrd_base/openrd_base.c +++ b/board/Marvell/openrd_base/openrd_base.c @@ -113,17 +113,6 @@ int board_init(void) return 0; } -int dram_init(void) -{ - int i; - - for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { - gd->bd->bi_dram[i].start = kw_sdram_bar(i); - gd->bd->bi_dram[i].size = kw_sdram_bs(i); - } - return 0; -} - #ifdef CONFIG_RESET_PHY_R /* Configure and enable MV88E1116 PHY */ void reset_phy(void) diff --git a/board/Marvell/rd6281a/rd6281a.c b/board/Marvell/rd6281a/rd6281a.c index 8713a3cf9b2..0d76146b658 100644 --- a/board/Marvell/rd6281a/rd6281a.c +++ b/board/Marvell/rd6281a/rd6281a.c @@ -109,17 +109,6 @@ int board_init(void) return 0; } -int dram_init(void) -{ - int i; - - for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { - gd->bd->bi_dram[i].start = kw_sdram_bar(i); - gd->bd->bi_dram[i].size = kw_sdram_bs(i); - } - return 0; -} - void mv_phy_88e1116_init(char *name) { u16 reg; diff --git a/board/Marvell/sheevaplug/sheevaplug.c b/board/Marvell/sheevaplug/sheevaplug.c index 547126af8f0..173a7b809df 100644 --- a/board/Marvell/sheevaplug/sheevaplug.c +++ b/board/Marvell/sheevaplug/sheevaplug.c @@ -108,17 +108,6 @@ int board_init(void) return 0; } -int dram_init(void) -{ - int i; - - for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { - gd->bd->bi_dram[i].start = kw_sdram_bar(i); - gd->bd->bi_dram[i].size = kw_sdram_bs(i); - } - return 0; -} - #ifdef CONFIG_RESET_PHY_R /* Configure and enable MV88E1116 PHY */ void reset_phy(void) diff --git a/board/armltd/integrator/split_by_variant.sh b/board/armltd/integrator/split_by_variant.sh index 702b436c8e1..d869dd2b75b 100755 --- a/board/armltd/integrator/split_by_variant.sh +++ b/board/armltd/integrator/split_by_variant.sh @@ -10,12 +10,12 @@ then # --------------------------------------------------------- # Set the platform defines # --------------------------------------------------------- -echo -n "/* Integrator configuration implied " > ${config_file} -echo " by Makefile target */" >> ${config_file} -echo -n "#define CONFIG_INTEGRATOR" >> ${config_file} -echo " /* Integrator board */" >> ${config_file} -echo -n "#define CONFIG_ARCH_INTEGRATOR" >> ${config_file} -echo " 1 /* Integrator/AP */" >> ${config_file} +cat > ${config_file} << _EOF +/* Integrator configuration implied by Makefile target */ +#define CONFIG_INTEGRATOR /* Integrator board */ +#define CONFIG_ARCH_INTEGRATOR 1 /* Integrator/AP */ +_EOF + # --------------------------------------------------------- # Set the core module defines according to Core Module # --------------------------------------------------------- @@ -50,37 +50,37 @@ else ap720t_config) cpu="arm720t" - echo -n "#define CONFIG_CM720T" >> ${config_file} - echo " 1 /* CPU core is ARM720T */ " >> ${config_file} + echo "#define CONFIG_CM720T 1 /* CPU core is ARM720T */" \ + >> ${config_file} variant="Core module CM720T" ;; ap922_XA10_config) cpu="arm_intcm" variant="unported core module CM922T_XA10" - echo -n "#define CONFIG_CM922T_XA10" >> ${config_file} - echo " 1 /* CPU core is ARM922T_XA10 */" >> ${config_file} + echo "#define CONFIG_CM922T_XA10 1 /* CPU core is ARM922T_XA10 */" \ + >> ${config_file} ;; ap920t_config) cpu="arm920t" variant="Core module CM920T" - echo -n "#define CONFIG_CM920T" >> ${config_file} - echo " 1 /* CPU core is ARM920T */" >> ${config_file} + echo "#define CONFIG_CM920T 1 /* CPU core is ARM920T */" \ + >> ${config_file} ;; ap926ejs_config) cpu="arm926ejs" variant="Core module CM926EJ-S" - echo -n "#define CONFIG_CM926EJ_S" >> ${config_file} - echo " 1 /* CPU core is ARM926EJ-S */ " >> ${config_file} + echo "#define CONFIG_CM926EJ_S 1 /* CPU core is ARM926EJ-S */" \ + >> ${config_file} ;; ap946es_config) cpu="arm946es" variant="Core module CM946E-S" - echo -n "#define CONFIG_CM946E_S" >> ${config_file} - echo " 1 /* CPU core is ARM946E-S */ " >> ${config_file} + echo "#define CONFIG_CM946E_S 1 /* CPU core is ARM946E-S */" \ + >> ${config_file} ;; *) @@ -94,33 +94,26 @@ fi case "$cpu" in arm_intcm) - echo "/* Core module undefined/not ported */" >> ${config_file} - echo "#define CONFIG_ARM_INTCM 1" >> ${config_file} - echo -n "#undef CONFIG_CM_MULTIPLE_SSRAM" >> ${config_file} - echo -n " /* CM may not have " >> ${config_file} - echo "multiple SSRAM mapping */" >> ${config_file} - echo -n "#undef CONFIG_CM_SPD_DETECT " >> ${config_file} - echo -n " /* CM may not support SPD " >> ${config_file} - echo "query */" >> ${config_file} - echo -n "#undef CONFIG_CM_REMAP " >> ${config_file} - echo -n " /* CM may not support " >> ${config_file} - echo "remapping */" >> ${config_file} - echo -n "#undef CONFIG_CM_INIT " >> ${config_file} - echo -n " /* CM may not have " >> ${config_file} - echo "initialization reg */" >> ${config_file} - echo -n "#undef CONFIG_CM_TCRAM " >> ${config_file} - echo " /* CM may not have TCRAM */" >> ${config_file} - echo -n " /* May not be processor " >> ${config_file} - echo "without cache support */" >> ${config_file} - echo "#define CONFIG_SYS_NO_ICACHE 1" >> ${config_file} - echo "#define CONFIG_SYS_NO_DCACHE 1" >> ${config_file} + cat >> ${config_file} << _EOF +/* Core module undefined/not ported */ +#define CONFIG_ARM_INTCM 1 +#undef CONFIG_CM_MULTIPLE_SSRAM /* CM may not have multiple SSRAM mapping */ +#undef CONFIG_CM_SPD_DETECT /* CM may not support SPD query */ +#undef CONFIG_CM_REMAP /* CM may not support remapping */ +#undef CONFIG_CM_INIT /* CM may not have initialization reg */ +#undef CONFIG_CM_TCRAM /* CM may not have TCRAM */ +/* May not be processor without cache support */ +#define CONFIG_SYS_NO_ICACHE 1 +#define CONFIG_SYS_NO_DCACHE 1 +_EOF ;; arm720t) - echo -n " /* May not be processor " >> ${config_file} - echo "without cache support */" >> ${config_file} - echo "#define CONFIG_SYS_NO_ICACHE 1" >> ${config_file} - echo "#define CONFIG_SYS_NO_DCACHE 1" >> ${config_file} + cat >> ${config_file} << _EOF +/* May not be processor without cache support */ +#define CONFIG_SYS_NO_ICACHE 1 +#define CONFIG_SYS_NO_DCACHE 1 +_EOF ;; esac @@ -129,12 +122,11 @@ else # --------------------------------------------------------- # Set the platform defines # --------------------------------------------------------- -echo -n "/* Integrator configuration implied " > ${config_file} -echo " by Makefile target */" >> ${config_file} -echo -n "#define CONFIG_INTEGRATOR" >> ${config_file} -echo " /* Integrator board */" >> ${config_file} -echo -n "#define CONFIG_ARCH_CINTEGRATOR" >> ${config_file} -echo " 1 /* Integrator/CP */" >> ${config_file} +cat >> ${config_file} << _EOF +/* Integrator configuration implied by Makefile target */ +#define CONFIG_INTEGRATOR /* Integrator board */ +#define CONFIG_ARCH_CINTEGRATOR 1 /* Integrator/CP */ +_EOF cpu="arm_intcm" variant="unknown core module" @@ -163,37 +155,37 @@ else cp922_XA10_config) cpu="arm_intcm" variant="unported core module CM922T_XA10" - echo -n "#define CONFIG_CM922T_XA10" >> ${config_file} - echo " 1 /* CPU core is ARM922T_XA10 */" >> ${config_file} + echo "#define CONFIG_CM922T_XA10 1 /* CPU core is ARM922T_XA10 */" \ + >> ${config_file} ;; cp920t_config) cpu="arm920t" variant="Core module CM920T" - echo -n "#define CONFIG_CM920T" >> ${config_file} - echo " 1 /* CPU core is ARM920T */" >> ${config_file} + echo "#define CONFIG_CM920T 1 /* CPU core is ARM920T */" \ + >> ${config_file} ;; cp926ejs_config) cpu="arm926ejs" variant="Core module CM926EJ-S" - echo -n "#define CONFIG_CM926EJ_S" >> ${config_file} - echo " 1 /* CPU core is ARM926EJ-S */ " >> ${config_file} + echo "#define CONFIG_CM926EJ_S 1 /* CPU core is ARM926EJ-S */" \ + >> ${config_file} ;; cp946es_config) cpu="arm946es" variant="Core module CM946E-S" - echo -n "#define CONFIG_CM946E_S" >> ${config_file} - echo " 1 /* CPU core is ARM946E-S */ " >> ${config_file} + echo "#define CONFIG_CM946E_S 1 /* CPU core is ARM946E-S */" \ + >> ${config_file} ;; cp1136_config) cpu="arm1136" variant="Core module CM1136EJF-S" - echo -n "#define CONFIG_CM1136EJF_S" >> ${config_file} - echo " 1 /* CPU core is ARM1136JF-S */ " >> ${config_file} + echo "#define CONFIG_CM1136EJF_S 1 /* CPU core is ARM1136JF-S */" \ + >> ${config_file} ;; *) @@ -208,22 +200,15 @@ fi if [ "$cpu" = "arm_intcm" ] then - echo "/* Core module undefined/not ported */" >> ${config_file} - echo "#define CONFIG_ARM_INTCM 1" >> ${config_file} - echo -n "#undef CONFIG_CM_MULTIPLE_SSRAM" >> ${config_file} - echo -n " /* CM may not have " >> ${config_file} - echo "multiple SSRAM mapping */" >> ${config_file} - echo -n "#undef CONFIG_CM_SPD_DETECT " >> ${config_file} - echo -n " /* CM may not support SPD " >> ${config_file} - echo "query */" >> ${config_file} - echo -n "#undef CONFIG_CM_REMAP " >> ${config_file} - echo -n " /* CM may not support " >> ${config_file} - echo "remapping */" >> ${config_file} - echo -n "#undef CONFIG_CM_INIT " >> ${config_file} - echo -n " /* CM may not have " >> ${config_file} - echo "initialization reg */" >> ${config_file} - echo -n "#undef CONFIG_CM_TCRAM " >> ${config_file} - echo " /* CM may not have TCRAM */" >> ${config_file} + cat >> ${config_file} << _EOF +/* Core module undefined/not ported */ +#define CONFIG_ARM_INTCM 1 +#undef CONFIG_CM_MULTIPLE_SSRAM /* CM may not have multiple SSRAM mapping */ +#undef CONFIG_CM_SPD_DETECT /* CM may not support SPD query */ +#undef CONFIG_CM_REMAP /* CM may not support remapping */ +#undef CONFIG_CM_INIT /* CM may not have initialization reg */ +#undef CONFIG_CM_TCRAM /* CM may not have TCRAM */ +_EOF fi fi # ap diff --git a/board/armltd/vexpress/Makefile b/board/armltd/vexpress/Makefile new file mode 100644 index 00000000000..ee5c0d87ac0 --- /dev/null +++ b/board/armltd/vexpress/Makefile @@ -0,0 +1,49 @@ +# +# (C) Copyright 2000-2004 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS := ca9x4_ct_vxp.o + +SRCS := $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak $(obj).depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/armltd/vexpress/ca9x4_ct_vxp.c b/board/armltd/vexpress/ca9x4_ct_vxp.c new file mode 100644 index 00000000000..48dfc8c4358 --- /dev/null +++ b/board/armltd/vexpress/ca9x4_ct_vxp.c @@ -0,0 +1,220 @@ +/* + * (C) Copyright 2002 + * Sysgo Real-Time Solutions, GmbH <www.elinos.com> + * Marius Groeger <mgroeger@sysgo.de> + * + * (C) Copyright 2002 + * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch> + * + * (C) Copyright 2003 + * Texas Instruments, <www.ti.com> + * Kshitij Gupta <Kshitij@ti.com> + * + * (C) Copyright 2004 + * ARM Ltd. + * Philippe Robin, <philippe.robin@arm.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#include <common.h> +#include <netdev.h> +#include <asm/io.h> +#include <asm/arch/systimer.h> +#include <asm/arch/sysctrl.h> +#include <asm/arch/wdt.h> + +static ulong timestamp; +static ulong lastdec; + +static struct wdt *wdt_base = (struct wdt *)WDT_BASE; +static struct systimer *systimer_base = (struct systimer *)SYSTIMER_BASE; +static struct sysctrl *sysctrl_base = (struct sysctrl *)SCTL_BASE; + +static void flash__init(void); +static void vexpress_timer_init(void); +DECLARE_GLOBAL_DATA_PTR; + +#if defined(CONFIG_SHOW_BOOT_PROGRESS) +void show_boot_progress(int progress) +{ + printf("Boot reached stage %d\n", progress); +} +#endif + +static inline void delay(ulong loops) +{ + __asm__ volatile ("1:\n" + "subs %0, %1, #1\n" + "bne 1b" : "=r" (loops) : "0" (loops)); +} + +int board_init(void) +{ + gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR; + gd->bd->bi_arch_number = MACH_TYPE_VEXPRESS; + gd->flags = 0; + + icache_enable(); + flash__init(); + vexpress_timer_init(); + + return 0; +} + +int board_eth_init(bd_t *bis) +{ + int rc = 0; +#ifdef CONFIG_SMC911X + rc = smc911x_initialize(0, CONFIG_SMC911X_BASE); +#endif + return rc; +} + +static void flash__init(void) +{ + /* Setup the sytem control register to allow writing to flash */ + writel(readl(&sysctrl_base->scflashctrl) | VEXPRESS_FLASHPROG_FLVPPEN, + &sysctrl_base->scflashctrl); +} + +int dram_init(void) +{ + gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE, PHYS_SDRAM_1_SIZE); + return 0; +} + +void dram_init_banksize(void) +{ + gd->bd->bi_dram[0].start = PHYS_SDRAM_1; + gd->bd->bi_dram[0].size = get_ram_size(PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE); + gd->bd->bi_dram[1].start = PHYS_SDRAM_2; + gd->bd->bi_dram[1].size = get_ram_size(PHYS_SDRAM_2, PHYS_SDRAM_2_SIZE); +} + +int timer_init(void) +{ + return 0; +} + +/* + * Start timer: + * Setup a 32 bit timer, running at 1KHz + * Versatile Express Motherboard provides 1 MHz timer + */ +static void vexpress_timer_init(void) +{ + /* + * Set clock frequency in system controller: + * VEXPRESS_REFCLK is 32KHz + * VEXPRESS_TIMCLK is 1MHz + */ + writel(SP810_TIMER0_ENSEL | SP810_TIMER1_ENSEL | + SP810_TIMER2_ENSEL | SP810_TIMER3_ENSEL | + readl(&sysctrl_base->scctrl), &sysctrl_base->scctrl); + + /* + * Set Timer0 to be: + * Enabled, free running, no interrupt, 32-bit, wrapping + */ + writel(SYSTIMER_RELOAD, &systimer_base->timer0load); + writel(SYSTIMER_RELOAD, &systimer_base->timer0value); + writel(SYSTIMER_EN | SYSTIMER_32BIT | \ + readl(&systimer_base->timer0control), \ + &systimer_base->timer0control); + + reset_timer_masked(); +} + +/* Use the ARM Watchdog System to cause reset */ +void reset_cpu(ulong addr) +{ + writeb(WDT_EN, &wdt_base->wdogcontrol); + writel(WDT_RESET_LOAD, &wdt_base->wdogload); + while (1) + ; +} + +/* + * Delay x useconds AND perserve advance timstamp value + * assumes timer is ticking at 1 msec + */ +void udelay(ulong usec) +{ + ulong tmo, tmp; + + tmo = usec / 1000; + tmp = get_timer(0); /* get current timestamp */ + + /* + * If setting this forward will roll time stamp then + * reset "advancing" timestamp to 0 and set lastdec value + * otherwise set the advancing stamp to the wake up time + */ + if ((tmo + tmp + 1) < tmp) + reset_timer_masked(); + else + tmo += tmp; + + while (get_timer_masked() < tmo) + ; /* loop till wakeup event */ +} + +ulong get_timer(ulong base) +{ + return get_timer_masked() - base; +} + +void reset_timer_masked(void) +{ + lastdec = readl(&systimer_base->timer0value) / 1000; + timestamp = 0; +} + +void reset_timer(void) +{ + reset_timer_masked(); +} + +ulong get_timer_masked(void) +{ + ulong now = readl(&systimer_base->timer0value) / 1000; + + if (lastdec >= now) { /* normal mode (non roll) */ + timestamp += lastdec - now; + } else { /* count down timer overflowed */ + /* + * nts = ts + ld - now + * ts = old stamp, ld = time before passing through - 1 + * now = amount of time after passing though - 1 + * nts = new "advancing time stamp" + */ + timestamp += lastdec + SYSTIMER_RELOAD - now; + } + lastdec = now; + + return timestamp; +} + +void lowlevel_init(void) +{ +} + +ulong get_board_rev(void){ + return readl((u32 *)SYS_ID); +} diff --git a/board/armltd/vexpress/config.mk b/board/armltd/vexpress/config.mk new file mode 100644 index 00000000000..2d797d7151c --- /dev/null +++ b/board/armltd/vexpress/config.mk @@ -0,0 +1,23 @@ +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# +# Linux-Kernel is expected to be at 0x60008000 +# +TEXT_BASE = 0x60800000 +LDSCRIPT := $(SRCTREE)/board/armltd/vexpress/u-boot.lds diff --git a/board/armltd/vexpress/u-boot.lds b/board/armltd/vexpress/u-boot.lds new file mode 100644 index 00000000000..5ac62f2c24a --- /dev/null +++ b/board/armltd/vexpress/u-boot.lds @@ -0,0 +1,65 @@ +/* + * (C) Copyright 2002 + * Gary Jennejohn, DENX Software Engineering, <gj@denx.de> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm") +OUTPUT_ARCH(arm) +ENTRY(_start) +SECTIONS +{ + . = 0x00000000; + . = ALIGN(4); + .text : + { + arch/arm/cpu/armv7/start.o (.text) + *(.text) + } + + . = ALIGN(4); + .rodata : { *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata))) } + + . = ALIGN(4); + .data : { *(.data) + __datarel_start = .; + *(.data.rel) + __datarelrolocal_start = .; + *(.data.rel.ro.local) + __datarellocal_start = .; + *(.data.rel.local) + __datarelro_start = .; + *(.data.rel.ro) + } + + __got_start = .; + . = ALIGN(4); + .got : { *(.got) } + __got_end = .; + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + . = ALIGN(4); + __bss_start = .; + .bss : { *(.bss) } + _end = .; +} diff --git a/board/davedenx/qong/qong.c b/board/davedenx/qong/qong.c index e509383e8fd..9abc29c5f70 100644 --- a/board/davedenx/qong/qong.c +++ b/board/davedenx/qong/qong.c @@ -27,6 +27,7 @@ #include <asm/arch/mx31-regs.h> #include <nand.h> #include <fsl_pmic.h> +#include <mxc_gpio.h> #include "qong_fpga.h" DECLARE_GLOBAL_DATA_PTR; @@ -41,9 +42,9 @@ int dram_init (void) static void qong_fpga_reset(void) { - mx31_gpio_set(QONG_FPGA_RST_PIN, 0); + mxc_gpio_set(QONG_FPGA_RST_PIN, 0); udelay(30); - mx31_gpio_set(QONG_FPGA_RST_PIN, 1); + mxc_gpio_set(QONG_FPGA_RST_PIN, 1); udelay(300); } @@ -66,11 +67,11 @@ int board_early_init_f (void) /* FPGA reset Pin */ /* rstn = 0 */ - mx31_gpio_set(QONG_FPGA_RST_PIN, 0); - mx31_gpio_direction(QONG_FPGA_RST_PIN, MX31_GPIO_DIRECTION_OUT); + mxc_gpio_set(QONG_FPGA_RST_PIN, 0); + mxc_gpio_direction(QONG_FPGA_RST_PIN, MXC_GPIO_DIRECTION_OUT); /* set interrupt pin as input */ - mx31_gpio_direction(QONG_FPGA_IRQ_PIN, MX31_GPIO_DIRECTION_IN); + mxc_gpio_direction(QONG_FPGA_IRQ_PIN, MXC_GPIO_DIRECTION_IN); #endif @@ -206,27 +207,27 @@ static void board_nand_setup(void) qong_fpga_reset(); /* Enable NAND flash */ - mx31_gpio_set(15, 1); - mx31_gpio_set(14, 1); - mx31_gpio_direction(15, MX31_GPIO_DIRECTION_OUT); - mx31_gpio_direction(16, MX31_GPIO_DIRECTION_IN); - mx31_gpio_direction(14, MX31_GPIO_DIRECTION_IN); - mx31_gpio_set(15, 0); + mxc_gpio_set(15, 1); + mxc_gpio_set(14, 1); + mxc_gpio_direction(15, MXC_GPIO_DIRECTION_OUT); + mxc_gpio_direction(16, MXC_GPIO_DIRECTION_IN); + mxc_gpio_direction(14, MXC_GPIO_DIRECTION_IN); + mxc_gpio_set(15, 0); } int qong_nand_rdy(void *chip) { udelay(1); - return mx31_gpio_get(16); + return mxc_gpio_get(16); } void qong_nand_select_chip(struct mtd_info *mtd, int chip) { if (chip >= 0) - mx31_gpio_set(15, 0); + mxc_gpio_set(15, 0); else - mx31_gpio_set(15, 1); + mxc_gpio_set(15, 1); } diff --git a/board/freescale/mx51evk/mx51evk.c b/board/freescale/mx51evk/mx51evk.c index 75d642bf423..84386e6c8ff 100644 --- a/board/freescale/mx51evk/mx51evk.c +++ b/board/freescale/mx51evk/mx51evk.c @@ -33,12 +33,10 @@ #include <fsl_esdhc.h> #include <fsl_pmic.h> #include <mc13892.h> -#include "mx51evk.h" DECLARE_GLOBAL_DATA_PTR; static u32 system_rev; -struct io_board_ctrl *mx51_io_board; #ifdef CONFIG_FSL_ESDHC struct fsl_esdhc_cfg esdhc_cfg[2] = { diff --git a/board/ttcontrol/vision2/Makefile b/board/ttcontrol/vision2/Makefile new file mode 100644 index 00000000000..309e3a3df6b --- /dev/null +++ b/board/ttcontrol/vision2/Makefile @@ -0,0 +1,48 @@ +# +# Copyright (C) 2007, Guennadi Liakhovetski <lg@denx.de> +# +# (C) Copyright 2009 Freescale Semiconductor, Inc. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS := vision2.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/ttcontrol/vision2/config.mk b/board/ttcontrol/vision2/config.mk new file mode 100644 index 00000000000..59f3367cfc9 --- /dev/null +++ b/board/ttcontrol/vision2/config.mk @@ -0,0 +1,25 @@ +# +# Copyright 2009 Freescale Semiconductor, Inc. All Rights Reserved. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +LDSCRIPT = $(CPUDIR)/$(SOC)/u-boot.lds +TEXT_BASE = 0x97800000 +IMX_CONFIG = $(SRCTREE)/board/$(BOARDDIR)/imximage_hynix.cfg diff --git a/board/ttcontrol/vision2/imximage_hynix.cfg b/board/ttcontrol/vision2/imximage_hynix.cfg new file mode 100644 index 00000000000..ed531db0bc6 --- /dev/null +++ b/board/ttcontrol/vision2/imximage_hynix.cfg @@ -0,0 +1,209 @@ +# +# (C) Copyright 2009 +# Stefano Babic DENX Software Engineering sbabic@denx.de. +# +# (C) Copyright 2010 +# Klaus Steinhammer TTECH Control Gmbh kst@tttech.com +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not write to the Free Software +# Foundation Inc. 51 Franklin Street Fifth Floor Boston, +# MA 02110-1301 USA +# +# Refer docs/README.imxmage for more details about how-to configure +# and create imximage boot image +# +# The syntax is taken as close as possible with the kwbimage + +# Boot Device : one of +# spi, nand, onenand, sd + +BOOT_FROM spi + +# Device Configuration Data (DCD) +# +# Each entry must have the format: +# Addr-type Address Value +# +# where: +# Addr-type register length (1,2 or 4 bytes) +# Address absolute address of the register +# value value to be stored in the register + +####################### +### Disable WDOG ### +####################### +DATA 2 0x73f98000 0x30 + +####################### +### SET DDR Clk ### +####################### + +# CCM: CBMCR - ddr_clk_sel: axi_b (133MHz) +DATA 4 0x73FD4018 0x000024C0 + +# DOUBLE SPI CLK (13MHz->26 MHz Clock) +DATA 4 0x73FD4038 0x2010241 + +#IOMUXC_SW_PAD_CTL_PAD_CSPI1_MOSI HYS_ENABLE | DRV_MAX | SRE_FAST +DATA 4 0x73fa8600 0x00000107 +#IOMUXC_SW_PAD_CTL_PAD_CSPI1_MISO HYS_ENABLE | DRV_MAX | SRE_FAST +DATA 4 0x73fa8604 0x00000107 +#IOMUXC_SW_PAD_CTL_PAD_CSPI1_SS0 HYS_ENABLE | PKE_ENABLE | DRV_MAX | SRE_FAST +DATA 4 0x73fa8608 0x00000187 +#IOMUXC_SW_PAD_CTL_PAD_CSPI1_SS1 HYS_ENABLE | PKE_ENABLE | DRV_MAX | SRE_FAST +DATA 4 0x73fa860c 0x00000187 +#IOMUXC_SW_PAD_CTL_PAD_CSPI1_SCLK HYS_ENABLE | DRV_MAX | SRE_FAST +DATA 4 0x73fa8614 0x00000107 +#IOMUXC_SW_PAD_CTL_PAD_DI1_PIN11 HYS_ENABLE | DRV_MAX | SRE_FAST (CSPI1_SS2) +DATA 4 0x73fa86a8 0x00000187 + +####################### +### Settings IOMUXC ### +####################### + +# DDR IOMUX configuration +# Control, Data, Address pads are in their default state: HIGH DS, FAST SR. +# IOMUXC_SW_PAD_CTL_PAD_DRAM_SDCLK MAX DS +DATA 4 0x73fa84b8 0x000000e7 +# PVTC MAX (at GPC, PGR reg) +#DATA 4 0x73FD8004 0x1fc00000 + +#DQM0 DS high slew rate slow +DATA 4 0x73fa84d4 0x000000e4 +#DQM1 DS high slew rate slow +DATA 4 0x73fa84d8 0x000000e4 +#DQM2 DS high slew rate slow +DATA 4 0x73fa84dc 0x000000e4 +#DQM3 DS high slew rate slow +DATA 4 0x73fa84e0 0x000000e4 + +#IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS0 DS high & SLEW slow +DATA 4 0x73fa84bc 0x000000c4 +#IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS1 DS high & SLEW slow +DATA 4 0x73fa84c0 0x000000c4 +#IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS2 DS high & SLEW slow +DATA 4 0x73fa84c4 0x000000c4 +#IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS3 DS high & SLEW slow +DATA 4 0x73fa84c8 0x000000c4 + +#DRAM_DATA B0 +DATA 4 0x73fa88a4 0x00000004 +#DRAM_DATA B1 +DATA 4 0x73fa88ac 0x00000004 +#DRAM_DATA B2 +DATA 4 0x73fa88b8 0x00000004 +#DRAM_DATA B3 +DATA 4 0x73fa882c 0x00000004 + +#DRAM_DATA B0 slew rate +DATA 4 0x73fa8878 0x00000000 +#DRAM_DATA B1 slew rate +DATA 4 0x73fa8880 0x00000000 +#DRAM_DATA B2 slew rate +DATA 4 0x73fa888c 0x00000000 +#DRAM_DATA B3 slew rate +DATA 4 0x73fa889c 0x00000000 + +####################### +### Configure SDRAM ### +####################### + +# Configure CS0 +####################### + +# ESDCTL0: Enable controller +DATA 4 0x83fd9000 0x83220000 + +# Init DRAM on CS0 +# ESDSCR: Precharge command +DATA 4 0x83fd9014 0x04008008 +# ESDSCR: Refresh command +DATA 4 0x83fd9014 0x00008010 +# ESDSCR: Refresh command +DATA 4 0x83fd9014 0x00008010 +# ESDSCR: LMR with CAS=3 and BL=3 (Burst Length = 8) +DATA 4 0x83fd9014 0x00338018 +# ESDSCR: EMR with half Drive strength (= medium strength @ i.MX51) +DATA 4 0x83fd9014 0x0020801a +# ESDSCR +DATA 4 0x83fd9014 0x00008000 + +# ESDSCR: EMR with full Drive strength +#DATA 4 0x83fd9014 0x0000801a + +# ESDCTL0: 14 ROW, 10 COL, 32Bit, SREF=8 +DATA 4 0x83fd9000 0xC3220000 + +# ESDCFG0: tRFC:22clks, tXSR:28clks, tXP:2clks, tWTR:2clk, tRP:3clks, tMRD:2clks +# tRAS:8clks, tRRD:2clks, tWR:3clks, tRCD:3clks, tRC:11clks +#DATA 4 0x83fd9004 0xC33574AA + +#micron mDDR +# ESDCFG0: tRFC:11clks, tXSR:19clks, tXP:1clks, tWTR:2clk, tRP:3clks, tMRD:2clks +# tRAS:7clks, tRRD:2clks, tWR:3clks, tRCD:3clks, tRC:9clks +#DATA 4 0x83FD9004 0x101564a8 + +#hynix mDDR +# ESDCFG0: tRFC:17clks, tXSR:21clks, tXP:3clks, tWTR:1clk, tRP:3clks, tMRD:2clks +# tRAS:7clks, tRRD:2clks, tWR:3clks, tRCD:3clks, tRC:9clks +DATA 4 0x83FD9004 0x704564a8 + +# ESDMISC: AP=10, Bank interleaving on, MIF3 en, RALAT=2 +DATA 4 0x83fd9010 0x000a1700 + +# Configure CS1 +####################### + +# ESDCTL1: Enable controller +DATA 4 0x83fd9008 0x83220000 + +# Init DRAM on CS1 +# ESDSCR: Precharge command +DATA 4 0x83fd9014 0x0400800c +# ESDSCR: Refresh command +DATA 4 0x83fd9014 0x00008014 +# ESDSCR: Refresh command +DATA 4 0x83fd9014 0x00008014 +# ESDSCR: LMR with CAS=3 and BL=3 (Burst Length = 8) +DATA 4 0x83fd9014 0x0033801c +# ESDSCR: EMR with half Drive strength (= medium strength @ i.MX51) +DATA 4 0x83fd9014 0x0020801e +# ESDSCR +DATA 4 0x83fd9014 0x00008004 + +# ESDCTL1: 14 ROW, 10 COL, 32Bit, SREF=8 +DATA 4 0x83fd9008 0xC3220000 + +# ESDCFG1: tRFC:22clks, tXSR:28clks, tXP:2clks, tWTR:2clk, tRP:3clks, tMRD:2clks +# tRAS:8clks, tRRD:2clks, tWR:3clks, tRCD:3clks, tRC:11clks +#DATA 4 0x83fd900c 0xC33574AA + +#micron mDDR +# ESDCFG1: tRFC:11clks, tXSR:19clks, tXP:1clks, tWTR:2clk, tRP:3clks, tMRD:2clks +# tRAS:7clks, tRRD:2clks, tWR:3clks, tRCD:3clks, tRC:9clks +#DATA 4 0x83FD900C 0x101564a8 + +#hynix mDDR +# ESDCFG0: tRFC:17clks, tXSR:21clks, tXP:3clks, tWTR:1clk, tRP:3clks, tMRD:2clks +# tRAS:7clks, tRRD:2clks, tWR:3clks, tRCD:3clks, tRC:9clks +DATA 4 0x83FD900C 0x704564a8 + +# ESDSCR (mDRAM configuration finished) +DATA 4 0x83FD9014 0x00000004 + +# ESDSCR - clear "configuration request" bit +DATA 4 0x83fd9014 0x00000000 diff --git a/board/ttcontrol/vision2/vision2.c b/board/ttcontrol/vision2/vision2.c new file mode 100644 index 00000000000..c991ee271ec --- /dev/null +++ b/board/ttcontrol/vision2/vision2.c @@ -0,0 +1,711 @@ +/* + * (C) Copyright 2010 + * Stefano Babic, DENX Software Engineering, sbabic@denx.de. + * + * (C) Copyright 2009 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/io.h> +#include <asm/arch/imx-regs.h> +#include <asm/arch/mx51_pins.h> +#include <asm/arch/crm_regs.h> +#include <asm/arch/iomux.h> +#include <mxc_gpio.h> +#include <asm/arch/sys_proto.h> +#include <asm/errno.h> +#include <i2c.h> +#include <mmc.h> +#include <fsl_esdhc.h> +#include <fsl_pmic.h> +#include <mc13892.h> + +DECLARE_GLOBAL_DATA_PTR; + +static u32 system_rev; + +#ifdef CONFIG_HW_WATCHDOG +#include <watchdog.h> + +void hw_watchdog_reset(void) +{ + int val; + + /* toggle watchdog trigger pin */ + val = mxc_gpio_get(66); + val = val ? 0 : 1; + mxc_gpio_set(66, val); +} +#endif + +static void init_drive_strength(void) +{ + mxc_iomux_set_pad(MX51_PIN_CTL_GRP_PKEDDR, PAD_CTL_DDR_INPUT_CMOS); + mxc_iomux_set_pad(MX51_PIN_CTL_GRP_PKEADDR, PAD_CTL_PKE_ENABLE); + mxc_iomux_set_pad(MX51_PIN_CTL_GRP_DDRAPKS, PAD_CTL_PUE_KEEPER); + mxc_iomux_set_pad(MX51_PIN_CTL_GRP_DDRAPUS, PAD_CTL_100K_PU); + mxc_iomux_set_pad(MX51_PIN_CTL_GRP_DDR_SR_A1, PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX51_PIN_CTL_GRP_DDR_A0, PAD_CTL_DRV_HIGH); + mxc_iomux_set_pad(MX51_PIN_CTL_GRP_DDR_A1, PAD_CTL_DRV_HIGH); + mxc_iomux_set_pad(MX51_PIN_CTL_DRAM_RAS, + PAD_CTL_DRV_HIGH | PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX51_PIN_CTL_DRAM_CAS, + PAD_CTL_DRV_HIGH | PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX51_PIN_CTL_GRP_PKEDDR, PAD_CTL_PKE_ENABLE); + mxc_iomux_set_pad(MX51_PIN_CTL_GRP_DDRPKS, PAD_CTL_PUE_KEEPER); + mxc_iomux_set_pad(MX51_PIN_CTL_GRP_HYSDDR0, PAD_CTL_HYS_NONE); + mxc_iomux_set_pad(MX51_PIN_CTL_GRP_HYSDDR1, PAD_CTL_HYS_NONE); + mxc_iomux_set_pad(MX51_PIN_CTL_GRP_HYSDDR2, PAD_CTL_HYS_NONE); + mxc_iomux_set_pad(MX51_PIN_CTL_GRP_HYSDDR3, PAD_CTL_HYS_NONE); + mxc_iomux_set_pad(MX51_PIN_CTL_GRP_DDR_SR_B0, PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX51_PIN_CTL_GRP_DDR_SR_B1, PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX51_PIN_CTL_GRP_DDR_SR_B2, PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX51_PIN_CTL_GRP_DDR_SR_B4, PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX51_PIN_CTL_GRP_DDRPUS, PAD_CTL_100K_PU); + mxc_iomux_set_pad(MX51_PIN_CTL_GRP_INMODE1, PAD_CTL_DDR_INPUT_CMOS); + mxc_iomux_set_pad(MX51_PIN_CTL_GRP_DRAM_B0, PAD_CTL_DRV_MEDIUM); + mxc_iomux_set_pad(MX51_PIN_CTL_GRP_DRAM_B1, PAD_CTL_DRV_MEDIUM); + mxc_iomux_set_pad(MX51_PIN_CTL_GRP_DRAM_B2, PAD_CTL_DRV_MEDIUM); + mxc_iomux_set_pad(MX51_PIN_CTL_GRP_DRAM_B4, PAD_CTL_DRV_MEDIUM); + + /* Setting pad options */ + mxc_iomux_set_pad(MX51_PIN_CTL_DRAM_SDWE, + PAD_CTL_PKE_ENABLE | PAD_CTL_PUE_KEEPER | + PAD_CTL_DRV_HIGH | PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX51_PIN_CTL_DRAM_SDCKE0, + PAD_CTL_PKE_ENABLE | PAD_CTL_PUE_KEEPER | + PAD_CTL_DRV_HIGH | PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX51_PIN_CTL_DRAM_SDCKE1, + PAD_CTL_PKE_ENABLE | PAD_CTL_PUE_KEEPER | + PAD_CTL_DRV_HIGH | PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX51_PIN_CTL_DRAM_SDCLK, + PAD_CTL_PKE_ENABLE | PAD_CTL_PUE_KEEPER | + PAD_CTL_DRV_HIGH | PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX51_PIN_CTL_DRAM_SDQS0, + PAD_CTL_PKE_ENABLE | PAD_CTL_PUE_KEEPER | + PAD_CTL_DRV_HIGH | PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX51_PIN_CTL_DRAM_SDQS1, + PAD_CTL_PKE_ENABLE | PAD_CTL_PUE_KEEPER | + PAD_CTL_DRV_HIGH | PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX51_PIN_CTL_DRAM_SDQS2, + PAD_CTL_PKE_ENABLE | PAD_CTL_PUE_KEEPER | + PAD_CTL_DRV_HIGH | PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX51_PIN_CTL_DRAM_SDQS3, + PAD_CTL_PKE_ENABLE | PAD_CTL_PUE_KEEPER | + PAD_CTL_DRV_HIGH | PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX51_PIN_CTL_DRAM_CS0, + PAD_CTL_PKE_ENABLE | PAD_CTL_PUE_KEEPER | + PAD_CTL_DRV_HIGH | PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX51_PIN_CTL_DRAM_CS1, + PAD_CTL_PKE_ENABLE | PAD_CTL_PUE_KEEPER | + PAD_CTL_DRV_HIGH | PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX51_PIN_CTL_DRAM_DQM0, + PAD_CTL_PKE_ENABLE | PAD_CTL_PUE_KEEPER | + PAD_CTL_DRV_HIGH | PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX51_PIN_CTL_DRAM_DQM1, + PAD_CTL_PKE_ENABLE | PAD_CTL_PUE_KEEPER | + PAD_CTL_DRV_HIGH | PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX51_PIN_CTL_DRAM_DQM2, + PAD_CTL_PKE_ENABLE | PAD_CTL_PUE_KEEPER | + PAD_CTL_DRV_HIGH | PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX51_PIN_CTL_DRAM_DQM3, + PAD_CTL_PKE_ENABLE | PAD_CTL_PUE_KEEPER | + PAD_CTL_DRV_HIGH | PAD_CTL_SRE_FAST); +} + +u32 get_board_rev(void) +{ + system_rev = get_cpu_rev(); + + return system_rev; +} + +int dram_init(void) +{ +#ifdef CONFIG_SYS_ARM_WITHOUT_RELOC + gd->bd->bi_dram[0].start = PHYS_SDRAM_1; + gd->bd->bi_dram[0].size = get_ram_size((long *)PHYS_SDRAM_1, + PHYS_SDRAM_1_SIZE); +#if (CONFIG_NR_DRAM_BANKS > 1) + gd->bd->bi_dram[1].start = PHYS_SDRAM_2; + gd->bd->bi_dram[1].size = get_ram_size((long *)PHYS_SDRAM_2, + PHYS_SDRAM_2_SIZE); +#endif +#else + gd->ram_size = get_ram_size((long *)PHYS_SDRAM_1, + PHYS_SDRAM_1_SIZE); +#endif + + return 0; +} + +static void setup_weim(void) +{ + struct weim *pweim = (struct weim *)WEIM_BASE_ADDR; + + pweim->csgcr1 = 0x004100b9; + pweim->csgcr2 = 0x00000001; + pweim->csrcr1 = 0x0a018000; + pweim->csrcr2 = 0; + pweim->cswcr1 = 0x0704a240; +} + +static void setup_uart(void) +{ + unsigned int pad = PAD_CTL_HYS_ENABLE | PAD_CTL_PKE_ENABLE | + PAD_CTL_PUE_PULL | PAD_CTL_DRV_HIGH | PAD_CTL_SRE_FAST; + /* console RX on Pin EIM_D25 */ + mxc_request_iomux(MX51_PIN_EIM_D25, IOMUX_CONFIG_ALT3); + mxc_iomux_set_pad(MX51_PIN_EIM_D25, pad); + /* console TX on Pin EIM_D26 */ + mxc_request_iomux(MX51_PIN_EIM_D26, IOMUX_CONFIG_ALT3); + mxc_iomux_set_pad(MX51_PIN_EIM_D26, pad); +} + +#ifdef CONFIG_MXC_SPI +void spi_io_init(void) +{ + /* 000: Select mux mode: ALT0 mux port: MOSI of instance: ecspi1 */ + mxc_request_iomux(MX51_PIN_CSPI1_MOSI, IOMUX_CONFIG_ALT0); + mxc_iomux_set_pad(MX51_PIN_CSPI1_MOSI, + PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST); + + /* 000: Select mux mode: ALT0 mux port: MISO of instance: ecspi1. */ + mxc_request_iomux(MX51_PIN_CSPI1_MISO, IOMUX_CONFIG_ALT0); + mxc_iomux_set_pad(MX51_PIN_CSPI1_MISO, + PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST); + + /* 000: Select mux mode: ALT0 mux port: SS0 of instance: ecspi1. */ + mxc_request_iomux(MX51_PIN_CSPI1_SS0, IOMUX_CONFIG_ALT0); + mxc_iomux_set_pad(MX51_PIN_CSPI1_SS0, + PAD_CTL_HYS_ENABLE | PAD_CTL_PKE_ENABLE | + PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST); + + /* + * SS1 will be used as GPIO because of uninterrupted + * long SPI transmissions (GPIO4_25) + */ + mxc_request_iomux(MX51_PIN_CSPI1_SS1, IOMUX_CONFIG_ALT3); + mxc_iomux_set_pad(MX51_PIN_CSPI1_SS1, + PAD_CTL_HYS_ENABLE | PAD_CTL_PKE_ENABLE | + PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST); + + /* 000: Select mux mode: ALT0 mux port: SS2 of instance: ecspi1. */ + mxc_request_iomux(MX51_PIN_DI1_PIN11, IOMUX_CONFIG_ALT7); + mxc_iomux_set_pad(MX51_PIN_DI1_PIN11, + PAD_CTL_HYS_ENABLE | PAD_CTL_PKE_ENABLE | + PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST); + + /* 000: Select mux mode: ALT0 mux port: SCLK of instance: ecspi1. */ + mxc_request_iomux(MX51_PIN_CSPI1_SCLK, IOMUX_CONFIG_ALT0); + mxc_iomux_set_pad(MX51_PIN_CSPI1_SCLK, + PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST); +} + +static void reset_peripherals(int reset) +{ + if (reset) { + + /* reset_n is on NANDF_D15 */ + mxc_gpio_set(89, 0); + mxc_gpio_direction(89, MXC_GPIO_DIRECTION_OUT); + +#ifdef CONFIG_VISION2_HW_1_0 + /* + * set FEC Configuration lines + * set levels of FEC config lines + */ + mxc_gpio_set(75, 0); + mxc_gpio_set(74, 1); + mxc_gpio_set(95, 1); + mxc_gpio_direction(75, MXC_GPIO_DIRECTION_OUT); + mxc_gpio_direction(74, MXC_GPIO_DIRECTION_OUT); + mxc_gpio_direction(95, MXC_GPIO_DIRECTION_OUT); + + /* set direction of FEC config lines */ + mxc_gpio_set(59, 0); + mxc_gpio_set(60, 0); + mxc_gpio_set(61, 0); + mxc_gpio_set(55, 1); + mxc_gpio_direction(59, MXC_GPIO_DIRECTION_OUT); + mxc_gpio_direction(60, MXC_GPIO_DIRECTION_OUT); + mxc_gpio_direction(61, MXC_GPIO_DIRECTION_OUT); + mxc_gpio_direction(55, MXC_GPIO_DIRECTION_OUT); + + /* FEC_RXD1 - sel GPIO (2-23) for configuration -> 1 */ + mxc_request_iomux(MX51_PIN_EIM_EB3, IOMUX_CONFIG_ALT1); + /* FEC_RXD2 - sel GPIO (2-27) for configuration -> 0 */ + mxc_request_iomux(MX51_PIN_EIM_CS2, IOMUX_CONFIG_ALT1); + /* FEC_RXD3 - sel GPIO (2-28) for configuration -> 0 */ + mxc_request_iomux(MX51_PIN_EIM_CS3, IOMUX_CONFIG_ALT1); + /* FEC_RXER - sel GPIO (2-29) for configuration -> 0 */ + mxc_request_iomux(MX51_PIN_EIM_CS4, IOMUX_CONFIG_ALT1); + /* FEC_COL - sel GPIO (3-10) for configuration -> 1 */ + mxc_request_iomux(MX51_PIN_NANDF_RB2, IOMUX_CONFIG_ALT3); + /* FEC_RCLK - sel GPIO (3-11) for configuration -> 0 */ + mxc_request_iomux(MX51_PIN_NANDF_RB3, IOMUX_CONFIG_ALT3); + /* FEC_RXD0 - sel GPIO (3-31) for configuration -> 1 */ + mxc_request_iomux(MX51_PIN_NANDF_D9, IOMUX_CONFIG_ALT3); +#endif + + /* + * activate reset_n pin + * Select mux mode: ALT3 mux port: NAND D15 + */ + mxc_request_iomux(MX51_PIN_NANDF_D15, IOMUX_CONFIG_ALT3); + mxc_iomux_set_pad(MX51_PIN_NANDF_D15, + PAD_CTL_DRV_VOT_HIGH | PAD_CTL_DRV_MAX); + } else { + /* set FEC Control lines */ + mxc_gpio_direction(89, MXC_GPIO_DIRECTION_IN); + udelay(500); + +#ifdef CONFIG_VISION2_HW_1_0 + /* FEC RDATA[3] */ + mxc_request_iomux(MX51_PIN_EIM_CS3, IOMUX_CONFIG_ALT3); + mxc_iomux_set_pad(MX51_PIN_EIM_CS3, 0x180); + + /* FEC RDATA[2] */ + mxc_request_iomux(MX51_PIN_EIM_CS2, IOMUX_CONFIG_ALT3); + mxc_iomux_set_pad(MX51_PIN_EIM_CS2, 0x180); + + /* FEC RDATA[1] */ + mxc_request_iomux(MX51_PIN_EIM_EB3, IOMUX_CONFIG_ALT3); + mxc_iomux_set_pad(MX51_PIN_EIM_EB3, 0x180); + + /* FEC RDATA[0] */ + mxc_request_iomux(MX51_PIN_NANDF_D9, IOMUX_CONFIG_ALT2); + mxc_iomux_set_pad(MX51_PIN_NANDF_D9, 0x2180); + + /* FEC RX_CLK */ + mxc_request_iomux(MX51_PIN_NANDF_RB3, IOMUX_CONFIG_ALT1); + mxc_iomux_set_pad(MX51_PIN_NANDF_RB3, 0x2180); + + /* FEC RX_ER */ + mxc_request_iomux(MX51_PIN_EIM_CS4, IOMUX_CONFIG_ALT3); + mxc_iomux_set_pad(MX51_PIN_EIM_CS4, 0x180); + + /* FEC COL */ + mxc_request_iomux(MX51_PIN_NANDF_RB2, IOMUX_CONFIG_ALT1); + mxc_iomux_set_pad(MX51_PIN_NANDF_RB2, 0x2180); +#endif + } +} + +static void power_init_mx51(void) +{ + unsigned int val; + + /* Write needed to Power Gate 2 register */ + val = pmic_reg_read(REG_POWER_MISC); + + /* enable VCAM with 2.775V to enable read from PMIC */ + val = VCAMCONFIG | VCAMEN; + pmic_reg_write(REG_MODE_1, val); + + /* + * Set switchers in Auto in NORMAL mode & STANDBY mode + * Setup the switcher mode for SW1 & SW2 + */ + val = pmic_reg_read(REG_SW_4); + val = (val & ~((SWMODE_MASK << SWMODE1_SHIFT) | + (SWMODE_MASK << SWMODE2_SHIFT))); + val |= (SWMODE_AUTO_AUTO << SWMODE1_SHIFT) | + (SWMODE_AUTO_AUTO << SWMODE2_SHIFT); + pmic_reg_write(REG_SW_4, val); + + /* Setup the switcher mode for SW3 & SW4 */ + val = pmic_reg_read(REG_SW_5); + val &= ~((SWMODE_MASK << SWMODE4_SHIFT) | + (SWMODE_MASK << SWMODE3_SHIFT)); + val |= (SWMODE_AUTO_AUTO << SWMODE4_SHIFT) | + (SWMODE_AUTO_AUTO << SWMODE3_SHIFT); + pmic_reg_write(REG_SW_5, val); + + + /* Set VGEN3 to 1.8V, VCAM to 3.0V */ + val = pmic_reg_read(REG_SETTING_0); + val &= ~(VCAM_MASK | VGEN3_MASK); + val |= VCAM_3_0; + pmic_reg_write(REG_SETTING_0, val); + + /* Set VVIDEO to 2.775V, VAUDIO to 3V0, VSD to 1.8V */ + val = pmic_reg_read(REG_SETTING_1); + val &= ~(VVIDEO_MASK | VSD_MASK | VAUDIO_MASK); + val |= VVIDEO_2_775 | VAUDIO_3_0 | VSD_1_8; + pmic_reg_write(REG_SETTING_1, val); + + /* Configure VGEN3 and VCAM regulators to use external PNP */ + val = VGEN3CONFIG | VCAMCONFIG; + pmic_reg_write(REG_MODE_1, val); + udelay(200); + + /* Enable VGEN3, VCAM, VAUDIO, VVIDEO, VSD regulators */ + val = VGEN3EN | VGEN3CONFIG | VCAMEN | VCAMCONFIG | + VVIDEOEN | VAUDIOEN | VSDEN; + pmic_reg_write(REG_MODE_1, val); + + val = pmic_reg_read(REG_POWER_CTL2); + val |= WDIRESET; + pmic_reg_write(REG_POWER_CTL2, val); + + udelay(2500); + +} +#endif + +static void setup_gpios(void) +{ + unsigned int i; + + /* CAM_SUP_DISn, GPIO1_7 */ + mxc_request_iomux(MX51_PIN_GPIO1_7, IOMUX_CONFIG_ALT0); + mxc_iomux_set_pad(MX51_PIN_GPIO1_7, 0x82); + + /* DAB Display EN, GPIO3_1 */ + mxc_request_iomux(MX51_PIN_DI1_PIN12, IOMUX_CONFIG_ALT4); + mxc_iomux_set_pad(MX51_PIN_DI1_PIN12, 0x82); + + /* WDOG_TRIGGER, GPIO3_2 */ + mxc_request_iomux(MX51_PIN_DI1_PIN13, IOMUX_CONFIG_ALT4); + mxc_iomux_set_pad(MX51_PIN_DI1_PIN13, 0x82); + + /* Now we need to trigger the watchdog */ + WATCHDOG_RESET(); + + /* Display2 TxEN, GPIO3_3 */ + mxc_request_iomux(MX51_PIN_DI1_D0_CS, IOMUX_CONFIG_ALT4); + mxc_iomux_set_pad(MX51_PIN_DI1_D0_CS, 0x82); + + /* DAB Light EN, GPIO3_4 */ + mxc_request_iomux(MX51_PIN_DI1_D1_CS, IOMUX_CONFIG_ALT4); + mxc_iomux_set_pad(MX51_PIN_DI1_D1_CS, 0x82); + + /* AUDIO_MUTE, GPIO3_5 */ + mxc_request_iomux(MX51_PIN_DISPB2_SER_DIN, IOMUX_CONFIG_ALT4); + mxc_iomux_set_pad(MX51_PIN_DISPB2_SER_DIN, 0x82); + + /* SPARE_OUT, GPIO3_6 */ + mxc_request_iomux(MX51_PIN_DISPB2_SER_DIO, IOMUX_CONFIG_ALT4); + mxc_iomux_set_pad(MX51_PIN_DISPB2_SER_DIO, 0x82); + + /* BEEPER_EN, GPIO3_26 */ + mxc_request_iomux(MX51_PIN_NANDF_D14, IOMUX_CONFIG_ALT3); + mxc_iomux_set_pad(MX51_PIN_NANDF_D14, 0x82); + + /* POWER_OFF, GPIO3_27 */ + mxc_request_iomux(MX51_PIN_NANDF_D13, IOMUX_CONFIG_ALT3); + mxc_iomux_set_pad(MX51_PIN_NANDF_D13, 0x82); + + /* FRAM_WE, GPIO3_30 */ + mxc_request_iomux(MX51_PIN_NANDF_D10, IOMUX_CONFIG_ALT3); + mxc_iomux_set_pad(MX51_PIN_NANDF_D10, 0x82); + + /* EXPANSION_EN, GPIO4_26 */ + mxc_request_iomux(MX51_PIN_CSPI1_RDY, IOMUX_CONFIG_ALT3); + mxc_iomux_set_pad(MX51_PIN_CSPI1_RDY, 0x82); + + /* + * Set GPIO1_4 to high and output; it is used to reset + * the system on reboot + */ + mxc_gpio_set(4, 1); + mxc_gpio_direction(4, MXC_GPIO_DIRECTION_OUT); + + mxc_gpio_set(7, 0); + mxc_gpio_direction(7, MXC_GPIO_DIRECTION_OUT); + for (i = 65; i < 71; i++) { + mxc_gpio_set(i, 0); + mxc_gpio_direction(i, MXC_GPIO_DIRECTION_OUT); + } + + mxc_gpio_set(94, 0); + mxc_gpio_direction(94, MXC_GPIO_DIRECTION_OUT); + + /* Set POWER_OFF high */ + mxc_gpio_set(91, 1); + mxc_gpio_direction(91, MXC_GPIO_DIRECTION_OUT); + + mxc_gpio_set(90, 0); + mxc_gpio_direction(90, MXC_GPIO_DIRECTION_OUT); + + mxc_gpio_set(122, 0); + mxc_gpio_direction(122, MXC_GPIO_DIRECTION_OUT); + + mxc_gpio_set(121, 1); + mxc_gpio_direction(121, MXC_GPIO_DIRECTION_OUT); + + WATCHDOG_RESET(); +} + +static void setup_fec(void) +{ + /*FEC_MDIO*/ + mxc_request_iomux(MX51_PIN_EIM_EB2, IOMUX_CONFIG_ALT3); + mxc_iomux_set_pad(MX51_PIN_EIM_EB2, 0x1FD); + + /*FEC_MDC*/ + mxc_request_iomux(MX51_PIN_NANDF_CS3, IOMUX_CONFIG_ALT2); + mxc_iomux_set_pad(MX51_PIN_NANDF_CS3, 0x2004); + + /* FEC RDATA[3] */ + mxc_request_iomux(MX51_PIN_EIM_CS3, IOMUX_CONFIG_ALT3); + mxc_iomux_set_pad(MX51_PIN_EIM_CS3, 0x180); + + /* FEC RDATA[2] */ + mxc_request_iomux(MX51_PIN_EIM_CS2, IOMUX_CONFIG_ALT3); + mxc_iomux_set_pad(MX51_PIN_EIM_CS2, 0x180); + + /* FEC RDATA[1] */ + mxc_request_iomux(MX51_PIN_EIM_EB3, IOMUX_CONFIG_ALT3); + mxc_iomux_set_pad(MX51_PIN_EIM_EB3, 0x180); + + /* FEC RDATA[0] */ + mxc_request_iomux(MX51_PIN_NANDF_D9, IOMUX_CONFIG_ALT2); + mxc_iomux_set_pad(MX51_PIN_NANDF_D9, 0x2180); + + /* FEC TDATA[3] */ + mxc_request_iomux(MX51_PIN_NANDF_CS6, IOMUX_CONFIG_ALT2); + mxc_iomux_set_pad(MX51_PIN_NANDF_CS6, 0x2004); + + /* FEC TDATA[2] */ + mxc_request_iomux(MX51_PIN_NANDF_CS5, IOMUX_CONFIG_ALT2); + mxc_iomux_set_pad(MX51_PIN_NANDF_CS5, 0x2004); + + /* FEC TDATA[1] */ + mxc_request_iomux(MX51_PIN_NANDF_CS4, IOMUX_CONFIG_ALT2); + mxc_iomux_set_pad(MX51_PIN_NANDF_CS4, 0x2004); + + /* FEC TDATA[0] */ + mxc_request_iomux(MX51_PIN_NANDF_D8, IOMUX_CONFIG_ALT2); + mxc_iomux_set_pad(MX51_PIN_NANDF_D8, 0x2004); + + /* FEC TX_EN */ + mxc_request_iomux(MX51_PIN_NANDF_CS7, IOMUX_CONFIG_ALT1); + mxc_iomux_set_pad(MX51_PIN_NANDF_CS7, 0x2004); + + /* FEC TX_ER */ + mxc_request_iomux(MX51_PIN_NANDF_CS2, IOMUX_CONFIG_ALT2); + mxc_iomux_set_pad(MX51_PIN_NANDF_CS2, 0x2004); + + /* FEC TX_CLK */ + mxc_request_iomux(MX51_PIN_NANDF_RDY_INT, IOMUX_CONFIG_ALT1); + mxc_iomux_set_pad(MX51_PIN_NANDF_RDY_INT, 0x2180); + + /* FEC TX_COL */ + mxc_request_iomux(MX51_PIN_NANDF_RB2, IOMUX_CONFIG_ALT1); + mxc_iomux_set_pad(MX51_PIN_NANDF_RB2, 0x2180); + + /* FEC RX_CLK */ + mxc_request_iomux(MX51_PIN_NANDF_RB3, IOMUX_CONFIG_ALT1); + mxc_iomux_set_pad(MX51_PIN_NANDF_RB3, 0x2180); + + /* FEC RX_CRS */ + mxc_request_iomux(MX51_PIN_EIM_CS5, IOMUX_CONFIG_ALT3); + mxc_iomux_set_pad(MX51_PIN_EIM_CS5, 0x180); + + /* FEC RX_ER */ + mxc_request_iomux(MX51_PIN_EIM_CS4, IOMUX_CONFIG_ALT3); + mxc_iomux_set_pad(MX51_PIN_EIM_CS4, 0x180); + + /* FEC RX_DV */ + mxc_request_iomux(MX51_PIN_NANDF_D11, IOMUX_CONFIG_ALT2); + mxc_iomux_set_pad(MX51_PIN_NANDF_D11, 0x2180); +} + +struct fsl_esdhc_cfg esdhc_cfg[1] = { + {MMC_SDHC1_BASE_ADDR, 1}, +}; + +int get_mmc_getcd(u8 *cd, struct mmc *mmc) +{ + struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; + + if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR) + *cd = mxc_gpio_get(0); + else + *cd = 0; + + return 0; +} + +#ifdef CONFIG_FSL_ESDHC +int board_mmc_init(bd_t *bis) +{ + mxc_request_iomux(MX51_PIN_SD1_CMD, + IOMUX_CONFIG_ALT0 | IOMUX_CONFIG_SION); + mxc_request_iomux(MX51_PIN_SD1_CLK, + IOMUX_CONFIG_ALT0 | IOMUX_CONFIG_SION); + mxc_request_iomux(MX51_PIN_SD1_DATA0, + IOMUX_CONFIG_ALT0 | IOMUX_CONFIG_SION); + mxc_request_iomux(MX51_PIN_SD1_DATA1, + IOMUX_CONFIG_ALT0 | IOMUX_CONFIG_SION); + mxc_request_iomux(MX51_PIN_SD1_DATA2, + IOMUX_CONFIG_ALT0 | IOMUX_CONFIG_SION); + mxc_request_iomux(MX51_PIN_SD1_DATA3, + IOMUX_CONFIG_ALT0 | IOMUX_CONFIG_SION); + mxc_iomux_set_pad(MX51_PIN_SD1_CMD, + PAD_CTL_DRV_MAX | PAD_CTL_DRV_VOT_HIGH | + PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU | + PAD_CTL_PUE_PULL | + PAD_CTL_PKE_ENABLE | PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX51_PIN_SD1_CLK, + PAD_CTL_DRV_MAX | PAD_CTL_DRV_VOT_HIGH | + PAD_CTL_HYS_NONE | PAD_CTL_47K_PU | + PAD_CTL_PUE_PULL | + PAD_CTL_PKE_ENABLE | PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX51_PIN_SD1_DATA0, + PAD_CTL_DRV_MAX | PAD_CTL_DRV_VOT_HIGH | + PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU | + PAD_CTL_PUE_PULL | + PAD_CTL_PKE_ENABLE | PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX51_PIN_SD1_DATA1, + PAD_CTL_DRV_MAX | PAD_CTL_DRV_VOT_HIGH | + PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU | + PAD_CTL_PUE_PULL | + PAD_CTL_PKE_ENABLE | PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX51_PIN_SD1_DATA2, + PAD_CTL_DRV_MAX | PAD_CTL_DRV_VOT_HIGH | + PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU | + PAD_CTL_PUE_PULL | + PAD_CTL_PKE_ENABLE | PAD_CTL_SRE_FAST); + mxc_iomux_set_pad(MX51_PIN_SD1_DATA3, + PAD_CTL_DRV_MAX | PAD_CTL_DRV_VOT_HIGH | + PAD_CTL_HYS_ENABLE | PAD_CTL_100K_PD | + PAD_CTL_PUE_PULL | + PAD_CTL_PKE_ENABLE | PAD_CTL_SRE_FAST); + mxc_request_iomux(MX51_PIN_GPIO1_0, + IOMUX_CONFIG_ALT0 | IOMUX_CONFIG_SION); + mxc_iomux_set_pad(MX51_PIN_GPIO1_0, + PAD_CTL_HYS_ENABLE); + mxc_request_iomux(MX51_PIN_GPIO1_1, + IOMUX_CONFIG_ALT0 | IOMUX_CONFIG_SION); + mxc_iomux_set_pad(MX51_PIN_GPIO1_1, + PAD_CTL_HYS_ENABLE); + + return fsl_esdhc_initialize(bis, &esdhc_cfg[0]); +} +#endif + +int board_early_init_f(void) +{ + + + init_drive_strength(); + + /* Setup debug led */ + mxc_gpio_set(6, 0); + mxc_gpio_direction(6, MXC_GPIO_DIRECTION_OUT); + mxc_request_iomux(MX51_PIN_GPIO1_6, IOMUX_CONFIG_ALT0); + mxc_iomux_set_pad(MX51_PIN_GPIO1_6, PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST); + + /* wait a little while to give the pll time to settle */ + sdelay(100000); + + setup_weim(); + setup_uart(); + setup_fec(); + setup_gpios(); + + spi_io_init(); + + return 0; +} + +int board_init(void) +{ +#ifdef CONFIG_SYS_ARM_WITHOUT_RELOC + board_early_init_f(); +#endif + gd->bd->bi_arch_number = MACH_TYPE_TTC_VISION2; /* board id for linux */ + /* address of boot parameters */ + gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100; + + return 0; +} + +int board_late_init(void) +{ + power_init_mx51(); + + reset_peripherals(1); + udelay(2000); + reset_peripherals(0); + udelay(2000); + + /* Early revisions require a second reset */ +#ifdef CONFIG_VISION2_HW_1_0 + reset_peripherals(1); + udelay(2000); + reset_peripherals(0); + udelay(2000); +#endif + + return 0; +} + +int checkboard(void) +{ + u32 system_rev = get_cpu_rev(); + u32 cause; + struct src *src_regs = (struct src *)SRC_BASE_ADDR; + + puts("Board: TTControl Vision II CPU V"); + + switch (system_rev & 0xff) { + case CHIP_REV_3_0: + puts("3.0 ["); + break; + case CHIP_REV_2_5: + puts("2.5 ["); + break; + case CHIP_REV_2_0: + puts("2.0 ["); + break; + case CHIP_REV_1_1: + puts("1.1 ["); + break; + case CHIP_REV_1_0: + default: + puts("1.0 ["); + break; + } + + cause = src_regs->srsr; + switch (cause) { + case 0x0001: + puts("POR"); + break; + case 0x0009: + puts("RST"); + break; + case 0x0010: + case 0x0011: + puts("WDOG"); + break; + default: + printf("unknown 0x%x", cause); + } + puts("]\n"); + + return 0; +} + diff --git a/boards.cfg b/boards.cfg index 9226424d23d..132d178830a 100644 --- a/boards.cfg +++ b/boards.cfg @@ -47,6 +47,7 @@ jadecpu arm arm926ejs jadecpu syteco mb86r0x suen3 arm arm926ejs km_arm keymile kirkwood rd6281a arm arm926ejs - Marvell kirkwood mx51evk arm armv7 mx51evk freescale mx51 +vision2 arm armv7 vision2 ttcontrol mx51 actux1 arm ixp actux2 arm ixp actux3 arm ixp @@ -252,6 +253,7 @@ imx27lite arm arm926ejs imx27lite logicpd mx27 magnesium arm arm926ejs imx27lite logicpd mx27 omap5912osk arm arm926ejs - ti omap edminiv2 arm arm926ejs - LaCie orion5x +ca9x4_ct_vxp arm armv7 vexpress armltd omap3_overo arm armv7 overo - omap3 omap3_pandora arm armv7 pandora - omap3 omap3_zoom1 arm armv7 zoom1 logicpd omap3 diff --git a/drivers/block/mvsata_ide.c b/drivers/block/mvsata_ide.c index 077b2789bb3..3d6993ac2af 100644 --- a/drivers/block/mvsata_ide.c +++ b/drivers/block/mvsata_ide.c @@ -91,29 +91,48 @@ struct mvsata_port_registers { #define MVSATA_SSTATUS_DET_DEVCOMM 0x00000003 /* + * Status codes to return to client callers. Currently, callers ignore + * exact value and only care for zero or nonzero, so no need to make this + * public, it is only #define'd for clarity. + * If/when standard negative codes are implemented in U-boot, then these + * #defines should be moved to, or replaced by ones from, the common list + * of status codes. + */ + +#define MVSATA_STATUS_OK 0 +#define MVSATA_STATUS_TIMEOUT -1 + +/* * Initialize one MVSATAHC port: set SControl's IPM to "always active" * and DET to "reset", then wait for SStatus's DET to become "device and * comm ok" (or time out after 50 us if no device), then set SControl's * DET back to "no action". */ -static void mvsata_ide_initialize_port(struct mvsata_port_registers *port) +static int mvsata_ide_initialize_port(struct mvsata_port_registers *port) { u32 control; u32 status; - u32 tout = 50; /* wait at most 50 us for SATA reset to complete */ + u32 timeleft = 10000; /* wait at most 10 ms for SATA reset to complete */ + /* Set control IPM to 3 (no low power) and DET to 1 (initialize) */ control = readl(&port->scontrol); control = (control & ~MVSATA_SCONTROL_MASK) | MVSATA_PORT_INIT; writel(control, &port->scontrol); - while (--tout) { + /* Toggle control DET back to 0 (normal operation) */ + control = (control & ~MVSATA_SCONTROL_MASK) | MVSATA_PORT_USE; + writel(control, &port->scontrol); + /* wait for status DET to become 3 (device and communication OK) */ + while (--timeleft) { status = readl(&port->sstatus) & MVSATA_SSTATUS_DET_MASK; if (status == MVSATA_SSTATUS_DET_DEVCOMM) break; udelay(1); } - control = (control & ~MVSATA_SCONTROL_MASK) | MVSATA_PORT_USE; - writel(control, &port->scontrol); + /* return success or time-out error depending on time left */ + if (!timeleft) + return MVSATA_STATUS_TIMEOUT; + return MVSATA_STATUS_OK; } /* @@ -123,18 +142,23 @@ static void mvsata_ide_initialize_port(struct mvsata_port_registers *port) int ide_preinit(void) { + int status; /* Enable ATA port 0 (could be SATA port 0 or 1) if declared */ #if defined(CONFIG_SYS_ATA_IDE0_OFFSET) - mvsata_ide_initialize_port( + status = mvsata_ide_initialize_port( (struct mvsata_port_registers *) (CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE0_OFFSET)); + if (status) + return status; #endif /* Enable ATA port 1 (could be SATA port 0 or 1) if declared */ #if defined(CONFIG_SYS_ATA_IDE1_OFFSET) - mvsata_ide_initialize_port( + status = mvsata_ide_initialize_port( (struct mvsata_port_registers *) (CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE1_OFFSET)); + if (status) + return status; #endif - /* return 0 as we always succeed */ - return 0; + /* return success if all ports initializations succeeded */ + return MVSATA_STATUS_OK; } diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile index 07d395d898f..a0f455223b3 100644 --- a/drivers/gpio/Makefile +++ b/drivers/gpio/Makefile @@ -27,7 +27,7 @@ LIB := $(obj)libgpio.a COBJS-$(CONFIG_AT91_GPIO) += at91_gpio.o COBJS-$(CONFIG_KIRKWOOD_GPIO) += kw_gpio.o -COBJS-$(CONFIG_MX31_GPIO) += mx31_gpio.o +COBJS-$(CONFIG_MXC_GPIO) += mxc_gpio.o COBJS-$(CONFIG_PCA953X) += pca953x.o COBJS-$(CONFIG_S5P) += s5p_gpio.o diff --git a/drivers/gpio/mx31_gpio.c b/drivers/gpio/mxc_gpio.c index b07f0381561..663141f1b46 100644 --- a/drivers/gpio/mx31_gpio.c +++ b/drivers/gpio/mxc_gpio.c @@ -21,19 +21,29 @@ * MA 02111-1307 USA */ #include <common.h> -#include <asm/arch/mx31.h> +#ifdef CONFIG_MX31 #include <asm/arch/mx31-regs.h> +#endif +#ifdef CONFIG_MX51 +#include <asm/arch/imx-regs.h> +#endif +#include <asm/io.h> +#include <mxc_gpio.h> /* GPIO port description */ static unsigned long gpio_ports[] = { - [0] = GPIO1_BASE, - [1] = GPIO2_BASE, - [2] = GPIO3_BASE, + [0] = GPIO1_BASE_ADDR, + [1] = GPIO2_BASE_ADDR, + [2] = GPIO3_BASE_ADDR, +#ifdef CONFIG_MX51 + [3] = GPIO4_BASE_ADDR, +#endif }; -int mx31_gpio_direction(unsigned int gpio, enum mx31_gpio_direction direction) +int mxc_gpio_direction(unsigned int gpio, enum mxc_gpio_direction direction) { unsigned int port = gpio >> 5; + struct gpio_regs *regs; u32 l; if (port >= ARRAY_SIZE(gpio_ports)) @@ -41,22 +51,26 @@ int mx31_gpio_direction(unsigned int gpio, enum mx31_gpio_direction direction) gpio &= 0x1f; - l = __REG(gpio_ports[port] + GPIO_GDIR); + regs = (struct gpio_regs *)gpio_ports[port]; + + l = readl(®s->gpio_dir); + switch (direction) { - case MX31_GPIO_DIRECTION_OUT: + case MXC_GPIO_DIRECTION_OUT: l |= 1 << gpio; break; - case MX31_GPIO_DIRECTION_IN: + case MXC_GPIO_DIRECTION_IN: l &= ~(1 << gpio); } - __REG(gpio_ports[port] + GPIO_GDIR) = l; + writel(l, ®s->gpio_dir); return 0; } -void mx31_gpio_set(unsigned int gpio, unsigned int value) +void mxc_gpio_set(unsigned int gpio, unsigned int value) { unsigned int port = gpio >> 5; + struct gpio_regs *regs; u32 l; if (port >= ARRAY_SIZE(gpio_ports)) @@ -64,17 +78,20 @@ void mx31_gpio_set(unsigned int gpio, unsigned int value) gpio &= 0x1f; - l = __REG(gpio_ports[port] + GPIO_DR); + regs = (struct gpio_regs *)gpio_ports[port]; + + l = readl(®s->gpio_dr); if (value) l |= 1 << gpio; else l &= ~(1 << gpio); - __REG(gpio_ports[port] + GPIO_DR) = l; + writel(l, ®s->gpio_dr); } -int mx31_gpio_get(unsigned int gpio) +int mxc_gpio_get(unsigned int gpio) { unsigned int port = gpio >> 5; + struct gpio_regs *regs; u32 l; if (port >= ARRAY_SIZE(gpio_ports)) @@ -82,7 +99,9 @@ int mx31_gpio_get(unsigned int gpio) gpio &= 0x1f; - l = (__REG(gpio_ports[port] + GPIO_DR) >> gpio) & 0x01; + regs = (struct gpio_regs *)gpio_ports[port]; + + l = (readl(®s->gpio_dr) >> gpio) & 0x01; return l; } diff --git a/drivers/misc/fsl_pmic.c b/drivers/misc/fsl_pmic.c index dca0a1d57e7..5ee1de176ea 100644 --- a/drivers/misc/fsl_pmic.c +++ b/drivers/misc/fsl_pmic.c @@ -46,6 +46,7 @@ void pmic_spi_free(struct spi_slave *slave) u32 pmic_reg(u32 reg, u32 val, u32 write) { u32 pmic_tx, pmic_rx; + u32 tmp; if (!slave) { slave = pmic_spi_probe(); @@ -65,7 +66,9 @@ u32 pmic_reg(u32 reg, u32 val, u32 write) pmic_tx = (write << 31) | (reg << 25) | (val & 0x00FFFFFF); - if (spi_xfer(slave, 4 << 3, &pmic_tx, &pmic_rx, + tmp = cpu_to_be32(pmic_tx); + + if (spi_xfer(slave, 4 << 3, &tmp, &pmic_rx, SPI_XFER_BEGIN | SPI_XFER_END)) { spi_release_bus(slave); return -1; @@ -73,7 +76,8 @@ u32 pmic_reg(u32 reg, u32 val, u32 write) if (write) { pmic_tx &= ~(1 << 31); - if (spi_xfer(slave, 4 << 3, &pmic_tx, &pmic_rx, + tmp = cpu_to_be32(pmic_tx); + if (spi_xfer(slave, 4 << 3, &tmp, &pmic_rx, SPI_XFER_BEGIN | SPI_XFER_END)) { spi_release_bus(slave); return -1; @@ -81,7 +85,7 @@ u32 pmic_reg(u32 reg, u32 val, u32 write) } spi_release_bus(slave); - return pmic_rx; + return cpu_to_be32(pmic_rx); } void pmic_reg_write(u32 reg, u32 value) diff --git a/drivers/net/at91_emac.c b/drivers/net/at91_emac.c index c525eeda42a..4e5685c0c32 100644 --- a/drivers/net/at91_emac.c +++ b/drivers/net/at91_emac.c @@ -127,13 +127,19 @@ void at91emac_DisableMDIO(at91_emac_t *at91mac) int at91emac_read(at91_emac_t *at91mac, unsigned char addr, unsigned char reg, unsigned short *value) { + unsigned long netstat; at91emac_EnableMDIO(at91mac); writel(AT91_EMAC_MAN_HIGH | AT91_EMAC_MAN_RW_R | AT91_EMAC_MAN_REGA(reg) | AT91_EMAC_MAN_CODE_802_3 | AT91_EMAC_MAN_PHYA(addr), &at91mac->man); - udelay(10000); + + do { + netstat = readl(&at91mac->sr); + DEBUG_AT91PHY("poll SR %08lx\n", netstat); + } while (!(netstat & AT91_EMAC_SR_IDLE)); + *value = readl(&at91mac->man) & AT91_EMAC_MAN_DATA_MASK; at91emac_DisableMDIO(at91mac); @@ -146,6 +152,7 @@ int at91emac_read(at91_emac_t *at91mac, unsigned char addr, int at91emac_write(at91_emac_t *at91mac, unsigned char addr, unsigned char reg, unsigned short value) { + unsigned long netstat; DEBUG_AT91PHY("AT91PHY write %x REG(%d)=%x\n", at91mac, reg, &value) at91emac_EnableMDIO(at91mac); @@ -154,9 +161,14 @@ int at91emac_write(at91_emac_t *at91mac, unsigned char addr, AT91_EMAC_MAN_REGA(reg) | AT91_EMAC_MAN_CODE_802_3 | AT91_EMAC_MAN_PHYA(addr) | (value & AT91_EMAC_MAN_DATA_MASK), &at91mac->man); - udelay(10000); + + do { + netstat = readl(&at91mac->sr); + DEBUG_AT91PHY("poll SR %08lx\n", netstat); + } while (!(netstat & AT91_EMAC_SR_IDLE)); at91emac_DisableMDIO(at91mac); + return 0; } @@ -500,11 +512,7 @@ int at91emac_register(bd_t *bis, unsigned long iobase) memset(emacfix, 0, sizeof(emac_device)); memset(dev, 0, sizeof(*dev)); -#ifndef CONFIG_RMII - sprintf(dev->name, "AT91 EMAC"); -#else - sprintf(dev->name, "AT91 EMAC RMII"); -#endif + sprintf(dev->name, "emac"); dev->iobase = iobase; dev->priv = emacfix; dev->init = at91emac_init; diff --git a/drivers/serial/atmel_usart.c b/drivers/serial/atmel_usart.c index cad34122b9d..bfa1f3a8d52 100644 --- a/drivers/serial/atmel_usart.c +++ b/drivers/serial/atmel_usart.c @@ -1,6 +1,9 @@ /* * Copyright (C) 2004-2006 Atmel Corporation * + * Modified to support C structur SoC access by + * Andreas Bießmann <biessmann@corscience.de> + * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or @@ -16,10 +19,6 @@ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ #include <common.h> -#ifndef CONFIG_AT91_LEGACY -#define CONFIG_AT91_LEGACY -#warning Please update to use C structur SoC access ! -#endif #include <watchdog.h> #include <asm/io.h> @@ -46,6 +45,7 @@ DECLARE_GLOBAL_DATA_PTR; void serial_setbrg(void) { + atmel_usart3_t *usart = (atmel_usart3_t*)USART_BASE; unsigned long divisor; unsigned long usart_hz; @@ -56,32 +56,37 @@ void serial_setbrg(void) */ usart_hz = get_usart_clk_rate(USART_ID); divisor = (usart_hz / 16 + gd->baudrate / 2) / gd->baudrate; - usart3_writel(BRGR, USART3_BF(CD, divisor)); + writel(USART3_BF(CD, divisor), &usart->brgr); } int serial_init(void) { - usart3_writel(CR, USART3_BIT(RSTRX) | USART3_BIT(RSTTX)); + atmel_usart3_t *usart = (atmel_usart3_t*)USART_BASE; + + writel(USART3_BIT(RSTRX) | USART3_BIT(RSTTX), &usart->cr); serial_setbrg(); - usart3_writel(CR, USART3_BIT(RXEN) | USART3_BIT(TXEN)); - usart3_writel(MR, (USART3_BF(USART_MODE, USART3_USART_MODE_NORMAL) + writel(USART3_BIT(RXEN) | USART3_BIT(TXEN), &usart->cr); + writel((USART3_BF(USART_MODE, USART3_USART_MODE_NORMAL) | USART3_BF(USCLKS, USART3_USCLKS_MCK) | USART3_BF(CHRL, USART3_CHRL_8) | USART3_BF(PAR, USART3_PAR_NONE) - | USART3_BF(NBSTOP, USART3_NBSTOP_1))); + | USART3_BF(NBSTOP, USART3_NBSTOP_1)), + &usart->mr); return 0; } void serial_putc(char c) { + atmel_usart3_t *usart = (atmel_usart3_t*)USART_BASE; + if (c == '\n') serial_putc('\r'); - while (!(usart3_readl(CSR) & USART3_BIT(TXRDY))) ; - usart3_writel(THR, c); + while (!(readl(&usart->csr) & USART3_BIT(TXRDY))); + writel(c, &usart->thr); } void serial_puts(const char *s) @@ -92,12 +97,15 @@ void serial_puts(const char *s) int serial_getc(void) { - while (!(usart3_readl(CSR) & USART3_BIT(RXRDY))) + atmel_usart3_t *usart = (atmel_usart3_t*)USART_BASE; + + while (!(readl(&usart->csr) & USART3_BIT(RXRDY))) WATCHDOG_RESET(); - return usart3_readl(RHR); + return readl(&usart->rhr); } int serial_tstc(void) { - return (usart3_readl(CSR) & USART3_BIT(RXRDY)) != 0; + atmel_usart3_t *usart = (atmel_usart3_t*)USART_BASE; + return (readl(&usart->csr) & USART3_BIT(RXRDY)) != 0; } diff --git a/drivers/serial/atmel_usart.h b/drivers/serial/atmel_usart.h index af3773a99f2..7cfc2d500cb 100644 --- a/drivers/serial/atmel_usart.h +++ b/drivers/serial/atmel_usart.h @@ -3,6 +3,9 @@ * * Copyright (C) 2005-2006 Atmel Corporation * + * Modified to support C structure SoC access by + * Andreas Bießmann <biessmann@corscience.de> + * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or @@ -20,32 +23,27 @@ #ifndef __DRIVERS_ATMEL_USART_H__ #define __DRIVERS_ATMEL_USART_H__ -/* USART3 register offsets */ -#define USART3_CR 0x0000 -#define USART3_MR 0x0004 -#define USART3_IER 0x0008 -#define USART3_IDR 0x000c -#define USART3_IMR 0x0010 -#define USART3_CSR 0x0014 -#define USART3_RHR 0x0018 -#define USART3_THR 0x001c -#define USART3_BRGR 0x0020 -#define USART3_RTOR 0x0024 -#define USART3_TTGR 0x0028 -#define USART3_FIDI 0x0040 -#define USART3_NER 0x0044 -#define USART3_XXR 0x0048 -#define USART3_IFR 0x004c -#define USART3_RPR 0x0100 -#define USART3_RCR 0x0104 -#define USART3_TPR 0x0108 -#define USART3_TCR 0x010c -#define USART3_RNPR 0x0110 -#define USART3_RNCR 0x0114 -#define USART3_TNPR 0x0118 -#define USART3_TNCR 0x011c -#define USART3_PTCR 0x0120 -#define USART3_PTSR 0x0124 +/* USART3 register footprint */ +typedef struct atmel_usart3 { + u32 cr; + u32 mr; + u32 ier; + u32 idr; + u32 imr; + u32 csr; + u32 rhr; + u32 thr; + u32 brgr; + u32 rtor; + u32 ttgr; + u32 reserved0[5]; + u32 fidi; + u32 ner; + u32 reserved1; + u32 ifr; + u32 man; + u32 reserved2[54]; // version and PDC not needed +} atmel_usart3_t; /* Bitfields in CR */ #define USART3_RSTRX_OFFSET 2 @@ -305,10 +303,4 @@ << USART3_##name##_OFFSET)) \ | USART3_BF(name,value)) -/* Register access macros */ -#define usart3_readl(reg) \ - readl((void *)USART_BASE + USART3_##reg) -#define usart3_writel(reg,value) \ - writel((value), (void *)USART_BASE + USART3_##reg) - #endif /* __DRIVERS_ATMEL_USART_H__ */ diff --git a/drivers/serial/serial_mxc.c b/drivers/serial/serial_mxc.c index 4b93e7b97fe..f96b21f7b1b 100644 --- a/drivers/serial/serial_mxc.c +++ b/drivers/serial/serial_mxc.c @@ -18,6 +18,7 @@ */ #include <common.h> +#include <watchdog.h> #ifdef CONFIG_MX31 #include <asm/arch/mx31.h> #else @@ -189,7 +190,8 @@ void serial_setbrg (void) int serial_getc (void) { - while (__REG(UART_PHYS + UTS) & UTS_RXEMPTY); + while (__REG(UART_PHYS + UTS) & UTS_RXEMPTY) + WATCHDOG_RESET(); return (__REG(UART_PHYS + URXD) & URXD_RX_DATA); /* mask out status from upper word */ } @@ -198,7 +200,8 @@ void serial_putc (const char c) __REG(UART_PHYS + UTXD) = c; /* wait for transmitter to be ready */ - while(!(__REG(UART_PHYS + UTS) & UTS_TXEMPTY)); + while (!(__REG(UART_PHYS + UTS) & UTS_TXEMPTY)) + WATCHDOG_RESET(); /* If \n, also do \r */ if (c == '\n') diff --git a/drivers/serial/serial_pl01x.c b/drivers/serial/serial_pl01x.c index c645cef8765..c0ae9472424 100644 --- a/drivers/serial/serial_pl01x.c +++ b/drivers/serial/serial_pl01x.c @@ -29,25 +29,23 @@ #include <common.h> #include <watchdog.h> - +#include <asm/io.h> #include "serial_pl01x.h" -#define IO_WRITE(addr, val) (*(volatile unsigned int *)(addr) = (val)) -#define IO_READ(addr) (*(volatile unsigned int *)(addr)) - /* * Integrator AP has two UARTs, we use the first one, at 38400-8-N-1 * Integrator CP has two UARTs, use the first one, at 38400-8-N-1 * Versatile PB has four UARTs. */ #define CONSOLE_PORT CONFIG_CONS_INDEX -#define baudRate CONFIG_BAUDRATE static volatile unsigned char *const port[] = CONFIG_PL01x_PORTS; #define NUM_PORTS (sizeof(port)/sizeof(port[0])) static void pl01x_putc (int portnum, char c); static int pl01x_getc (int portnum); static int pl01x_tstc (int portnum); +unsigned int baudrate = CONFIG_BAUDRATE; +DECLARE_GLOBAL_DATA_PTR; #ifdef CONFIG_PL010_SERIAL @@ -55,16 +53,11 @@ int serial_init (void) { unsigned int divisor; - /* - ** First, disable everything. - */ - IO_WRITE (port[CONSOLE_PORT] + UART_PL010_CR, 0x0); + /* First, disable everything */ + writel(0x0, port[CONSOLE_PORT] + UART_PL010_CR); - /* - ** Set baud rate - ** - */ - switch (baudRate) { + /* Set baud rate */ + switch (baudrate) { case 9600: divisor = UART_PL010_BAUD_9600; break; @@ -89,20 +82,15 @@ int serial_init (void) divisor = UART_PL010_BAUD_38400; } - IO_WRITE (port[CONSOLE_PORT] + UART_PL010_LCRM, - ((divisor & 0xf00) >> 8)); - IO_WRITE (port[CONSOLE_PORT] + UART_PL010_LCRL, (divisor & 0xff)); + writel(((divisor & 0xf00) >> 8), port[CONSOLE_PORT] + UART_PL010_LCRM); + writel((divisor & 0xff), port[CONSOLE_PORT] + UART_PL010_LCRL); - /* - ** Set the UART to be 8 bits, 1 stop bit, no parity, fifo enabled. - */ - IO_WRITE (port[CONSOLE_PORT] + UART_PL010_LCRH, - (UART_PL010_LCRH_WLEN_8 | UART_PL010_LCRH_FEN)); + /* Set the UART to be 8 bits, 1 stop bit, no parity, fifo enabled */ + writel((UART_PL010_LCRH_WLEN_8 | UART_PL010_LCRH_FEN), + port[CONSOLE_PORT] + UART_PL010_LCRH); - /* - ** Finally, enable the UART - */ - IO_WRITE (port[CONSOLE_PORT] + UART_PL010_CR, (UART_PL010_CR_UARTEN)); + /* Finally, enable the UART */ + writel((UART_PL010_CR_UARTEN), port[CONSOLE_PORT] + UART_PL010_CR); return 0; } @@ -118,38 +106,31 @@ int serial_init (void) unsigned int remainder; unsigned int fraction; - /* - ** First, disable everything. - */ - IO_WRITE (port[CONSOLE_PORT] + UART_PL011_CR, 0x0); + /* First, disable everything */ + writel(0x0, port[CONSOLE_PORT] + UART_PL011_CR); /* - ** Set baud rate - ** - ** IBRD = UART_CLK / (16 * BAUD_RATE) - ** FBRD = ROUND((64 * MOD(UART_CLK,(16 * BAUD_RATE))) / (16 * BAUD_RATE)) + * Set baud rate + * + * IBRD = UART_CLK / (16 * BAUD_RATE) + * FBRD = RND((64 * MOD(UART_CLK,(16 * BAUD_RATE))) / (16 * BAUD_RATE)) */ - temp = 16 * baudRate; + temp = 16 * baudrate; divider = CONFIG_PL011_CLOCK / temp; remainder = CONFIG_PL011_CLOCK % temp; - temp = (8 * remainder) / baudRate; + temp = (8 * remainder) / baudrate; fraction = (temp >> 1) + (temp & 1); - IO_WRITE (port[CONSOLE_PORT] + UART_PL011_IBRD, divider); - IO_WRITE (port[CONSOLE_PORT] + UART_PL011_FBRD, fraction); + writel(divider, port[CONSOLE_PORT] + UART_PL011_IBRD); + writel(fraction, port[CONSOLE_PORT] + UART_PL011_FBRD); - /* - ** Set the UART to be 8 bits, 1 stop bit, no parity, fifo enabled. - */ - IO_WRITE (port[CONSOLE_PORT] + UART_PL011_LCRH, - (UART_PL011_LCRH_WLEN_8 | UART_PL011_LCRH_FEN)); + /* Set the UART to be 8 bits, 1 stop bit, no parity, fifo enabled */ + writel((UART_PL011_LCRH_WLEN_8 | UART_PL011_LCRH_FEN), + port[CONSOLE_PORT] + UART_PL011_LCRH); - /* - ** Finally, enable the UART - */ - IO_WRITE (port[CONSOLE_PORT] + UART_PL011_CR, - (UART_PL011_CR_UARTEN | UART_PL011_CR_TXE | - UART_PL011_CR_RXE)); + /* Finally, enable the UART */ + writel((UART_PL011_CR_UARTEN | UART_PL011_CR_TXE | UART_PL011_CR_RXE), + port[CONSOLE_PORT] + UART_PL011_CR); return 0; } @@ -183,16 +164,18 @@ int serial_tstc (void) void serial_setbrg (void) { + baudrate = gd->baudrate; + serial_init(); } static void pl01x_putc (int portnum, char c) { /* Wait until there is space in the FIFO */ - while (IO_READ (port[portnum] + UART_PL01x_FR) & UART_PL01x_FR_TXFF) + while (readl(port[portnum] + UART_PL01x_FR) & UART_PL01x_FR_TXFF) WATCHDOG_RESET(); /* Send the character */ - IO_WRITE (port[portnum] + UART_PL01x_DR, c); + writel(c, port[portnum] + UART_PL01x_DR); } static int pl01x_getc (int portnum) @@ -200,15 +183,15 @@ static int pl01x_getc (int portnum) unsigned int data; /* Wait until there is data in the FIFO */ - while (IO_READ (port[portnum] + UART_PL01x_FR) & UART_PL01x_FR_RXFE) + while (readl(port[portnum] + UART_PL01x_FR) & UART_PL01x_FR_RXFE) WATCHDOG_RESET(); - data = IO_READ (port[portnum] + UART_PL01x_DR); + data = readl(port[portnum] + UART_PL01x_DR); /* Check for an error flag */ if (data & 0xFFFFFF00) { /* Clear the error */ - IO_WRITE (port[portnum] + UART_PL01x_ECR, 0xFFFFFFFF); + writel(0xFFFFFFFF, port[portnum] + UART_PL01x_ECR); return -1; } @@ -218,6 +201,6 @@ static int pl01x_getc (int portnum) static int pl01x_tstc (int portnum) { WATCHDOG_RESET(); - return !(IO_READ (port[portnum] + UART_PL01x_FR) & + return !(readl(port[portnum] + UART_PL01x_FR) & UART_PL01x_FR_RXFE); } diff --git a/drivers/spi/mxc_spi.c b/drivers/spi/mxc_spi.c index e15a63caca9..d558137c9d5 100644 --- a/drivers/spi/mxc_spi.c +++ b/drivers/spi/mxc_spi.c @@ -23,6 +23,7 @@ #include <spi.h> #include <asm/errno.h> #include <asm/io.h> +#include <mxc_gpio.h> #ifdef CONFIG_MX27 /* i.MX27 has a completely wrong register layout and register definitions in the @@ -61,6 +62,7 @@ #define MXC_CSPICTRL_MAXBITS 0x1f #define MXC_CSPIPERIOD_32KHZ (1 << 15) +#define MAX_SPI_BYTES 4 static unsigned long spi_bases[] = { 0x43fa4000, @@ -68,9 +70,6 @@ static unsigned long spi_bases[] = { 0x53f84000, }; -#define OUT MX31_GPIO_DIRECTION_OUT -#define mxc_gpio_direction mx31_gpio_direction -#define mxc_gpio_set mx31_gpio_set #elif defined(CONFIG_MX51) #include <asm/arch/imx-regs.h> #include <asm/arch/clock.h> @@ -97,6 +96,7 @@ static unsigned long spi_bases[] = { #define MXC_CSPICTRL_RXOVF (1 << 6) #define MXC_CSPIPERIOD_32KHZ (1 << 15) +#define MAX_SPI_BYTES 32 /* Bit position inside CTRL register to be associated with SS */ #define MXC_CSPICTRL_CHAN 18 @@ -111,13 +111,12 @@ static unsigned long spi_bases[] = { CSPI2_BASE_ADDR, CSPI3_BASE_ADDR, }; -#define mxc_gpio_direction(gpio, dir) (0) -#define mxc_gpio_set(gpio, value) {} -#define OUT 1 #else #error "Unsupported architecture" #endif +#define OUT MXC_GPIO_DIRECTION_OUT + struct mxc_spi_slave { struct spi_slave slave; unsigned long base; @@ -126,6 +125,7 @@ struct mxc_spi_slave { u32 cfg_reg; #endif int gpio; + int ss_pol; }; static inline struct mxc_spi_slave *to_mxc_spi_slave(struct spi_slave *slave) @@ -147,7 +147,7 @@ void spi_cs_activate(struct spi_slave *slave) { struct mxc_spi_slave *mxcs = to_mxc_spi_slave(slave); if (mxcs->gpio > 0) - mxc_gpio_set(mxcs->gpio, mxcs->ctrl_reg & MXC_CSPICTRL_SSPOL); + mxc_gpio_set(mxcs->gpio, mxcs->ss_pol); } void spi_cs_deactivate(struct spi_slave *slave) @@ -155,7 +155,7 @@ void spi_cs_deactivate(struct spi_slave *slave) struct mxc_spi_slave *mxcs = to_mxc_spi_slave(slave); if (mxcs->gpio > 0) mxc_gpio_set(mxcs->gpio, - !(mxcs->ctrl_reg & MXC_CSPICTRL_SSPOL)); + !(mxcs->ss_pol)); } #ifdef CONFIG_MX51 @@ -217,7 +217,7 @@ static s32 spi_cfg(struct mxc_spi_slave *mxcs, unsigned int cs, if (mode & SPI_CS_HIGH) ss_pol = 1; - if (!(mode & SPI_CPOL)) + if (mode & SPI_CPOL) sclkpol = 1; if (mode & SPI_CPHA) @@ -254,13 +254,15 @@ static s32 spi_cfg(struct mxc_spi_slave *mxcs, unsigned int cs, } #endif -static u32 spi_xchg_single(struct spi_slave *slave, u32 data, int bitlen, - unsigned long flags) +int spi_xchg_single(struct spi_slave *slave, unsigned int bitlen, + const u8 *dout, u8 *din, unsigned long flags) { struct mxc_spi_slave *mxcs = to_mxc_spi_slave(slave); + int nbytes = (bitlen + 7) / 8; + u32 data, cnt, i; - if (flags & SPI_XFER_BEGIN) - spi_cs_activate(slave); + debug("%s: bitlen %d dout 0x%x din 0x%x\n", + __func__, bitlen, (u32)dout, (u32)din); mxcs->ctrl_reg = (mxcs->ctrl_reg & ~MXC_CSPICTRL_BITCOUNT(MXC_CSPICTRL_MAXBITS)) | @@ -275,8 +277,46 @@ static u32 spi_xchg_single(struct spi_slave *slave, u32 data, int bitlen, reg_write(mxcs->base + MXC_CSPISTAT, MXC_CSPICTRL_TC | MXC_CSPICTRL_RXOVF); - debug("Sending SPI 0x%x\n", data); - reg_write(mxcs->base + MXC_CSPITXDATA, data); + /* + * The SPI controller works only with words, + * check if less than a word is sent. + * Access to the FIFO is only 32 bit + */ + if (bitlen % 32) { + data = 0; + cnt = (bitlen % 32) / 8; + if (dout) { + for (i = 0; i < cnt; i++) { + data = (data << 8) | (*dout++ & 0xFF); + } + } + debug("Sending SPI 0x%x\n", data); + + reg_write(mxcs->base + MXC_CSPITXDATA, data); + nbytes -= cnt; + } + + data = 0; + + while (nbytes > 0) { + data = 0; + if (dout) { + /* Buffer is not 32-bit aligned */ + if ((unsigned long)dout & 0x03) { + data = 0; + for (i = 0; i < 4; i++, data <<= 8) { + data = (data << 8) | (*dout++ & 0xFF); + } + } else { + data = *(u32 *)dout; + data = cpu_to_be32(data); + } + dout += 4; + } + debug("Sending SPI 0x%x\n", data); + reg_write(mxcs->base + MXC_CSPITXDATA, data); + nbytes -= 4; + } /* FIFO is written, now starts the transfer setting the XCH bit */ reg_write(mxcs->base + MXC_CSPICTRL, mxcs->ctrl_reg | @@ -290,49 +330,78 @@ static u32 spi_xchg_single(struct spi_slave *slave, u32 data, int bitlen, reg_write(mxcs->base + MXC_CSPISTAT, MXC_CSPICTRL_TC | MXC_CSPICTRL_RXOVF); - data = reg_read(mxcs->base + MXC_CSPIRXDATA); - debug("SPI Rx: 0x%x\n", data); + nbytes = (bitlen + 7) / 8; - if (flags & SPI_XFER_END) - spi_cs_deactivate(slave); + cnt = nbytes % 32; + + if (bitlen % 32) { + data = reg_read(mxcs->base + MXC_CSPIRXDATA); + cnt = (bitlen % 32) / 8; + debug("SPI Rx unaligned: 0x%x\n", data); + if (din) { + for (i = 0; i < cnt; i++, data >>= 8) { + *din++ = data & 0xFF; + } + } + nbytes -= cnt; + } - return data; + while (nbytes > 0) { + u32 tmp; + tmp = reg_read(mxcs->base + MXC_CSPIRXDATA); + data = cpu_to_be32(tmp); + debug("SPI Rx: 0x%x 0x%x\n", tmp, data); + cnt = min(nbytes, sizeof(data)); + if (din) { + memcpy(din, &data, cnt); + din += cnt; + } + nbytes -= cnt; + } + + return 0; } + int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *dout, void *din, unsigned long flags) { - int n_blks = (bitlen + 31) / 32; - u32 *out_l, *in_l; - int i; + int n_bytes = (bitlen + 7) / 8; + int n_bits; + int ret; + u32 blk_size; + u8 *p_outbuf = (u8 *)dout; + u8 *p_inbuf = (u8 *)din; - if ((int)dout & 3 || (int)din & 3) { - printf("Error: unaligned buffers in: %p, out: %p\n", din, dout); - return 1; - } + if (!slave) + return -1; + + if (flags & SPI_XFER_BEGIN) + spi_cs_activate(slave); + + while (n_bytes > 0) { + + if (n_bytes < MAX_SPI_BYTES) + blk_size = n_bytes; + else + blk_size = MAX_SPI_BYTES; + + n_bits = blk_size * 8; - /* This driver is currently partly broken, alert the user */ - if (bitlen > 16 && (bitlen % 32)) { - printf("Error: SPI transfer with bitlen=%d is broken.\n", - bitlen); - return 1; + ret = spi_xchg_single(slave, n_bits, p_outbuf, p_inbuf, 0); + + if (ret) + return ret; + if (dout) + p_outbuf += blk_size; + if (din) + p_inbuf += blk_size; + n_bytes -= blk_size; } - for (i = 0, in_l = (u32 *)din, out_l = (u32 *)dout; - i < n_blks; - i++, in_l++, out_l++, bitlen -= 32) { - u32 data = spi_xchg_single(slave, *out_l, bitlen, flags); - - /* Check if we're only transfering 8 or 16 bits */ - if (!i) { - if (bitlen < 9) - *(u8 *)din = data; - else if (bitlen < 17) - *(u16 *)din = data; - else - *in_l = data; - } + if (flags & SPI_XFER_END) { + spi_cs_deactivate(slave); } return 0; @@ -380,8 +449,10 @@ struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs, return NULL; mxcs = malloc(sizeof(struct mxc_spi_slave)); - if (!mxcs) + if (!mxcs) { + puts("mxc_spi: SPI Slave not allocated !\n"); return NULL; + } ret = decode_cs(mxcs, cs); if (ret < 0) { @@ -394,6 +465,7 @@ struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs, mxcs->slave.bus = bus; mxcs->slave.cs = cs; mxcs->base = spi_bases[bus]; + mxcs->ss_pol = (mode & SPI_CS_HIGH) ? 1 : 0; #ifdef CONFIG_MX51 /* Can be used for i.MX31 too ? */ @@ -413,7 +485,7 @@ struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs, if (mode & SPI_CPHA) ctrl_reg |= MXC_CSPICTRL_PHA; - if (!(mode & SPI_CPOL)) + if (mode & SPI_CPOL) ctrl_reg |= MXC_CSPICTRL_POL; if (mode & SPI_CS_HIGH) ctrl_reg |= MXC_CSPICTRL_SSPOL; diff --git a/include/configs/ca9x4_ct_vxp.h b/include/configs/ca9x4_ct_vxp.h new file mode 100644 index 00000000000..5547d55eecd --- /dev/null +++ b/include/configs/ca9x4_ct_vxp.h @@ -0,0 +1,196 @@ +/* + * (C) Copyright 2010 Linaro + * Matt Waddel, <matt.waddel@linaro.org> + * + * Configuration for Versatile Express. Parts were derived from other ARM + * configurations. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* Board info register */ +#define SYS_ID 0x10000000 +#define CONFIG_REVISION_TAG 1 + +/* High Level Configuration Options */ +#define CONFIG_ARMV7 1 + +#define CONFIG_SYS_MEMTEST_START 0x60000000 +#define CONFIG_SYS_MEMTEST_END 0x20000000 +#define CONFIG_SYS_HZ 1000 + +#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS 1 +#define CONFIG_L2_OFF 1 +#define CONFIG_INITRD_TAG 1 + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128 * 1024) +#define CONFIG_SYS_GBL_DATA_SIZE 128 + +#define SCTL_BASE 0x10001000 +#define VEXPRESS_FLASHPROG_FLVPPEN (1 << 0) + +/* SMSC9115 Ethernet from SMSC9118 family */ +#define CONFIG_NET_MULTI +#define CONFIG_SMC911X 1 +#define CONFIG_SMC911X_32_BIT 1 +#define CONFIG_SMC911X_BASE 0x4E000000 + +/* PL011 Serial Configuration */ +#define CONFIG_PL011_SERIAL +#define CONFIG_PL011_CLOCK 24000000 +#define CONFIG_PL01x_PORTS {(void *)CONFIG_SYS_SERIAL0, \ + (void *)CONFIG_SYS_SERIAL1} +#define CONFIG_CONS_INDEX 0 + +#define CONFIG_BAUDRATE 38400 +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } +#define CONFIG_SYS_SERIAL0 0x10009000 +#define CONFIG_SYS_SERIAL1 0x1000A000 + +/* Command line configuration */ +#define CONFIG_CMD_BDI +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_ELF +#define CONFIG_CMD_ENV +#define CONFIG_CMD_FLASH +#define CONFIG_CMD_IMI +#define CONFIG_CMD_MEMORY +#define CONFIG_CMD_NET +#define CONFIG_CMD_PING +#define CONFIG_CMD_SAVEENV +#define CONFIG_NET_MULTI +#define CONFIG_CMD_RUN + +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION 1 +#define CONFIG_MMC 1 +#define CONFIG_CMD_MMC +#define CONFIG_GENERIC_MMC + +/* BOOTP options */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + +/* Miscellaneous configurable options */ +#undef CONFIG_SYS_CLKS_IN_HZ +#define CONFIG_SYS_LOAD_ADDR 0x60008000 /* load address */ +#define LINUX_BOOT_PARAM_ADDR 0x60000200 +#define CONFIG_BOOTDELAY 2 + +/* Stack sizes are set up in start.S using the settings below */ +#define CONFIG_STACKSIZE (128 * 1024) /* regular stack */ +#ifdef CONFIG_USE_IRQ +#define CONFIG_STACKSIZE_IRQ (4 * 1024) /* IRQ stack */ +#define CONFIG_STACKSIZE_FIQ (4 * 1024) /* FIQ stack */ +#endif + +/* Physical Memory Map */ +#define CONFIG_NR_DRAM_BANKS 2 +#define PHYS_SDRAM_1 0x60000000 /* SDRAM Bank #1 */ +#define PHYS_SDRAM_2 0x80000000 /* SDRAM Bank #1 */ +#define PHYS_SDRAM_1_SIZE 0x20000000 /* 512 MB */ +#define PHYS_SDRAM_2_SIZE 0x20000000 /* 512 MB */ + +/* additions for new relocation code */ +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 +#define CONFIG_SYS_INIT_RAM_END 0x1000 +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_SDRAM_BASE + \ + CONFIG_SYS_INIT_RAM_END - \ + CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_GBL_DATA_OFFSET + +/* Basic environment settings */ +#define CONFIG_BOOTCOMMAND "run bootflash;" +#define CONFIG_EXTRA_ENV_SETTINGS \ + "loadaddr=0x80008000\0" \ + "initrd=0x61000000\0" \ + "kerneladdr=0x44100000\0" \ + "initrdaddr=0x44800000\0" \ + "maxinitrd=0x1800000\0" \ + "console=ttyAMA0,38400n8\0" \ + "dram=1024M\0" \ + "root=/dev/sda1 rw\0" \ + "mtd=armflash:1M@0x800000(uboot),7M@0x1000000(kernel)," \ + "24M@0x2000000(initrd)\0" \ + "flashargs=setenv bootargs root=${root} console=${console} " \ + "mem=${dram} mtdparts=${mtd} mmci.fmax=190000 " \ + "devtmpfs.mount=0 vmalloc=256M\0" \ + "bootflash=run flashargs; " \ + "cp ${initrdaddr} ${initrd} ${maxinitrd}; " \ + "bootm ${kerneladdr} ${initrd}\0" + +/* FLASH and environment organization */ +#define PHYS_FLASH_SIZE 0x04000000 /* 64MB */ +#define CONFIG_SYS_FLASH_CFI 1 +#define CONFIG_FLASH_CFI_DRIVER 1 +#define CONFIG_SYS_FLASH_SIZE 0x04000000 +#define CONFIG_SYS_MAX_FLASH_BANKS 2 +#define CONFIG_SYS_FLASH_BASE0 0x40000000 +#define CONFIG_SYS_FLASH_BASE1 0x44000000 +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE0 + +/* Timeout values in ticks */ +#define CONFIG_SYS_FLASH_ERASE_TOUT (2 * CONFIG_SYS_HZ) /* Erase Timeout */ +#define CONFIG_SYS_FLASH_WRITE_TOUT (2 * CONFIG_SYS_HZ) /* Write Timeout */ + +/* 255 0x40000 sectors + first or last sector may have 4 erase regions = 259 */ +#define CONFIG_SYS_MAX_FLASH_SECT 259 /* Max sectors */ +#define FLASH_MAX_SECTOR_SIZE 0x00040000 /* 256 KB sectors */ + +/* Room required on the stack for the environment data */ +#define CONFIG_ENV_SIZE FLASH_MAX_SECTOR_SIZE + +/* + * Amount of flash used for environment: + * We don't know which end has the small erase blocks so we use the penultimate + * sector location for the environment + */ +#define CONFIG_ENV_SECT_SIZE FLASH_MAX_SECTOR_SIZE +#define CONFIG_ENV_OVERWRITE 1 + +/* Store environment at top of flash */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_OFFSET (PHYS_FLASH_SIZE - \ + (2 * CONFIG_ENV_SECT_SIZE)) +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE1 + \ + CONFIG_ENV_OFFSET) +#define CONFIG_SYS_FLASH_PROTECTION /* The devices have real protection */ +#define CONFIG_SYS_FLASH_EMPTY_INFO /* flinfo indicates empty blocks */ +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE0, \ + CONFIG_SYS_FLASH_BASE1 } + +/* Monitor Command Prompt */ +#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PROMPT "VExpress# " +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */ +#define CONFIG_CMD_SOURCE +#define CONFIG_SYS_LONGHELP +#define CONFIG_CMDLINE_EDITING 1 +#define CONFIG_SYS_MAXARGS 16 /* max command args */ + +#endif diff --git a/include/configs/da850evm.h b/include/configs/da850evm.h index d02b1968b96..e0a3baee9e4 100644 --- a/include/configs/da850evm.h +++ b/include/configs/da850evm.h @@ -138,7 +138,6 @@ #endif /* additions for new relocation code, must added to all boards */ -#undef CONFIG_SYS_ARM_WITHOUT_RELOC /* This board is tested with relocation support */ #define CONFIG_SYS_SDRAM_BASE 0xc0000000 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \ CONFIG_SYS_GBL_DATA_SIZE) diff --git a/include/configs/guruplug.h b/include/configs/guruplug.h index eb3fa57d67e..2c2682cfadf 100644 --- a/include/configs/guruplug.h +++ b/include/configs/guruplug.h @@ -33,59 +33,13 @@ /* * High Level Configuration Options (easy to change) */ -#define CONFIG_MARVELL 1 -#define CONFIG_ARM926EJS 1 /* Basic Architecture */ #define CONFIG_SHEEVA_88SV131 1 /* CPU Core subversion */ #define CONFIG_KIRKWOOD 1 /* SOC Family Name */ #define CONFIG_KW88F6281 1 /* SOC Name */ #define CONFIG_MACH_GURUPLUG /* Machine type */ - -#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */ #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ -#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */ -#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */ - -/* - * CLKs configurations - */ -#define CONFIG_SYS_HZ 1000 - -/* - * NS16550 Configuration - */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (-4) -#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK -#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE - -/* - * Serial Port configuration - * The following definitions let you select what serial you want to use - * for your console driver. - */ - -#define CONFIG_CONS_INDEX 1 /*Console on UART0 */ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \ - 115200,230400, 460800, 921600 } -/* auto boot */ -#define CONFIG_BOOTDELAY 3 /* default enable autoboot */ /* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ -#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */ -#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */ - -#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */ -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ - +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */ -/* * Commands configuration */ #define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */ @@ -96,18 +50,13 @@ #define CONFIG_CMD_NAND #define CONFIG_CMD_PING #define CONFIG_CMD_USB +#define CONFIG_CMD_IDE /* - * NAND configuration + * mv-common.h should be defined after CMD configs since it used them + * to enable certain macros */ -#ifdef CONFIG_CMD_NAND -#define CONFIG_NAND_KIRKWOOD -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define NAND_MAX_CHIPS 1 -#define CONFIG_SYS_NAND_BASE 0xD8000000 /* KW_DEFADR_NANDF */ -#define NAND_ALLOW_ERASE_ALL 1 -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ -#endif +#include "mv-common.h" /* * Environment variables configurations @@ -143,55 +92,19 @@ "x_bootargs_root=ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs\0" /* - * Size of malloc() pool - */ -#define CONFIG_SYS_MALLOC_LEN (1024 * 128) /* 128kB for malloc() */ -/* size in bytes reserved for initial data */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 - -/* - * Other required configurations - */ -#define CONFIG_CONSOLE_INFO_QUIET /* some code reduction */ -#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */ -#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */ -#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */ -#define CONFIG_NR_DRAM_BANKS 4 -#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */ -#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */ -#define CONFIG_SYS_MEMTEST_START 0x00800000 /* 8M */ -#define CONFIG_SYS_MEMTEST_END 0x1fffffff /*(_512M -1) */ -#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ - -/* * Ethernet Driver configuration */ #ifdef CONFIG_CMD_NET -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_NET_MULTI /* specify more that one ports available */ -#define CONFIG_MII /* expose smi ove miiphy interface */ -#define CONFIG_CMD_MII -#define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */ -#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */ #define CONFIG_MVGBE_PORTS {1, 1} /* enable both ports */ #define CONFIG_PHY_BASE_ADR 0 -#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ -#define CONFIG_RESET_PHY_R /* use reset_phy() to init mv88e1121 PHY */ #endif /* CONFIG_CMD_NET */ /* - * USB/EHCI + * SATA Driver configuration */ -#ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI /* Enable EHCI USB support */ -#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */ -#define CONFIG_EHCI_IS_TDI -#define CONFIG_USB_STORAGE -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION -#define CONFIG_SUPPORT_VFAT -#endif /* CONFIG_CMD_USB */ +#ifdef CONFIG_MVSATA_IDE +#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET +#endif /*CONFIG_MVSATA_IDE*/ #define CONFIG_SYS_ALT_MEMTEST diff --git a/include/configs/h2_p2_dbg_board.h b/include/configs/h2_p2_dbg_board.h index e0d823f2dc3..a4dea7dd2f0 100644 --- a/include/configs/h2_p2_dbg_board.h +++ b/include/configs/h2_p2_dbg_board.h @@ -31,7 +31,7 @@ #ifndef __INCLUDED_H2_P2_DBH_BOARD_H #define __INCLUDED_H2_P2_DBH_BOARD_H -#include <asm/arch/sizes.h> +#include <asm/sizes.h> /* * The Debug board is designed to function with the P2 Sample, H2 diff --git a/include/configs/imx27lite-common.h b/include/configs/imx27lite-common.h index 812e5f2e718..88e8d3db104 100644 --- a/include/configs/imx27lite-common.h +++ b/include/configs/imx27lite-common.h @@ -235,8 +235,7 @@ "mtdids=" MTDIDS_DEFAULT "\0" \ "mtdparts=" MTDPARTS_DEFAULT "\0" \ -/* additions for new relocation code, must added to all boards */ -#undef CONFIG_SYS_ARM_WITHOUT_RELOC /* This board is tested with relocation support */ +/* additions for new relocation code, must be added to all boards */ #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \ CONFIG_SYS_GBL_DATA_SIZE) diff --git a/include/configs/imx31_litekit.h b/include/configs/imx31_litekit.h index 49048563cb5..88c62d11e1b 100644 --- a/include/configs/imx31_litekit.h +++ b/include/configs/imx31_litekit.h @@ -66,13 +66,13 @@ #define CONFIG_HARD_SPI 1 #define CONFIG_MXC_SPI 1 #define CONFIG_DEFAULT_SPI_BUS 1 -#define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_2 | SPI_CS_HIGH) +#define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_0 | SPI_CS_HIGH) #define CONFIG_FSL_PMIC #define CONFIG_FSL_PMIC_BUS 1 #define CONFIG_FSL_PMIC_CS 0 #define CONFIG_FSL_PMIC_CLK 1000000 -#define CONFIG_FSL_PMIC_MODE (SPI_MODE_2 | SPI_CS_HIGH) +#define CONFIG_FSL_PMIC_MODE (SPI_MODE_0 | SPI_CS_HIGH) #define CONFIG_RTC_MC13783 1 diff --git a/include/configs/imx31_phycore.h b/include/configs/imx31_phycore.h index 1dbafa0521c..62944a93f6e 100644 --- a/include/configs/imx31_phycore.h +++ b/include/configs/imx31_phycore.h @@ -183,7 +183,7 @@ #ifdef CONFIG_IMX31_PHYCORE_EET #define BOARD_LATE_INIT -#define CONFIG_MX31_GPIO 1 +#define CONFIG_MXC_GPIO #define CONFIG_HARD_SPI 1 #define CONFIG_MXC_SPI 1 diff --git a/include/configs/keymile-common.h b/include/configs/keymile-common.h index 6c14ca00c53..62d21f62866 100644 --- a/include/configs/keymile-common.h +++ b/include/configs/keymile-common.h @@ -85,6 +85,7 @@ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_SYS_BOARD_DRAM_INIT /* Used board specific dram_init */ /* * How to get access to the slot ID. Put this here to make it easy diff --git a/include/configs/km_arm.h b/include/configs/km_arm.h index 8673e6ff64d..faa0f503266 100644 --- a/include/configs/km_arm.h +++ b/include/configs/km_arm.h @@ -180,7 +180,7 @@ int get_scl (void); #undef CONFIG_JFFS2_CMDLINE #endif -/* additions for new relocation code, must added to all boards */ +/* additions for new relocation code, must be added to all boards */ #define CONFIG_SYS_SDRAM_BASE 0x00000000 #define CONFIG_SYS_INIT_SP_ADDR (0x00000000 + 0x1000 - /* Fix this */ \ CONFIG_SYS_GBL_DATA_SIZE) diff --git a/include/configs/mv-common.h b/include/configs/mv-common.h new file mode 100644 index 00000000000..bdcebd3b5de --- /dev/null +++ b/include/configs/mv-common.h @@ -0,0 +1,230 @@ +/* + * (C) Copyright 2010 + * Marvell Semiconductor <www.marvell.com> + * Written-by: Prafulla Wadaskar <prafulla@marvell.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +/* + * This file contains Marvell Board Specific common defincations. + * This file should be included in board config header file. + * + * It supports common definations for Kirkwood platform + * TBD: support for Orion5X platforms + */ + +#ifndef _MV_COMMON_H +#define _MV_COMMON_H + +/* + * High Level Configuration Options (easy to change) + */ +#define CONFIG_MARVELL 1 +#define CONFIG_ARM926EJS 1 /* Basic Architecture */ + +#if defined(CONFIG_KIRKWOOD) +#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */ +#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */ +#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */ +#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 for kernel */ + +#define CONFIG_I2C_MVTWSI_BASE KW_TWSI_BASE +#define MV_UART0_BASE KW_UART0_BASE +#define MV_SATA_BASE KW_SATA_BASE +#define MV_SATA_PORT0_OFFSET KW_SATA_PORT0_OFFSET +#define MV_SATA_PORT1_OFFSET KW_SATA_PORT1_OFFSET + +#else +#error "Unsupported SoC" +#endif + +/* additions for new ARM relocation support */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +/* Kirkwood has 2k of Security SRAM, use it for SP */ +#define CONFIG_SYS_INIT_SP_ADDR 0xC8012000 + +/* + * CLKs configurations + */ +#define CONFIG_SYS_HZ 1000 + +/* + * NS16550 Configuration + */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE (-4) +#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK +#define CONFIG_SYS_NS16550_COM1 MV_UART0_BASE + +/* + * Serial Port configuration + * The following definitions let you select what serial you want to use + * for your console driver. + */ + +#define CONFIG_CONS_INDEX 1 /*Console on UART0 */ +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \ + 115200,230400, 460800, 921600 } +/* auto boot */ +#define CONFIG_BOOTDELAY 3 /* default enable autoboot */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ +#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */ +#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */ + +#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ + +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */ + +/* + * NAND configuration + */ +#ifdef CONFIG_CMD_NAND +#define CONFIG_NAND_KIRKWOOD +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define NAND_MAX_CHIPS 1 +#define CONFIG_SYS_NAND_BASE 0xD8000000 /* MV_DEFADR_NANDF */ +#define NAND_ALLOW_ERASE_ALL 1 +#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ +#endif + +/* + * SPI Flash configuration + */ +#ifdef CONFIG_CMD_SF +#define CONFIG_SPI_FLASH 1 +#define CONFIG_HARD_SPI 1 +#define CONFIG_KIRKWOOD_SPI 1 +#define CONFIG_SPI_FLASH_MACRONIX 1 +#define CONFIG_ENV_SPI_BUS 0 +#define CONFIG_ENV_SPI_CS 0 +#define CONFIG_ENV_SPI_MAX_HZ 50000000 /*50Mhz */ +#endif + +/* + * Size of malloc() pool + */ +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* 1MiB for malloc() */ +/* size in bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_SIZE 128 + +/* + * Other required minimal configurations + */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_AUTO_COMPLETE +#define CONFIG_CMDLINE_EDITING +#define CONFIG_CONSOLE_INFO_QUIET /* some code reduction */ +#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */ +#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */ +#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */ +#define CONFIG_NR_DRAM_BANKS 4 +#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */ +#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */ +#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */ +#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */ +#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ + +/* + * Ethernet Driver configuration + */ +#ifdef CONFIG_CMD_NET +#define CONFIG_CMD_MII +#define CONFIG_NETCONSOLE /* include NetConsole support */ +#define CONFIG_NET_MULTI /* specify more that one ports available */ +#define CONFIG_MII /* expose smi ove miiphy interface */ +#define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */ +#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */ +#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ +#define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */ +#endif /* CONFIG_CMD_NET */ + +/* + * USB/EHCI + */ +#ifdef CONFIG_CMD_USB +#define CONFIG_USB_EHCI /* Enable EHCI USB support */ +#define CONFIG_USB_EHCI_KIRKWOOD +#define CONFIG_EHCI_IS_TDI +#define CONFIG_USB_STORAGE +#define CONFIG_DOS_PARTITION +#define CONFIG_ISO_PARTITION +#define CONFIG_SUPPORT_VFAT +#endif /* CONFIG_CMD_USB */ + +/* + * IDE Support on SATA ports + */ +#ifdef CONFIG_CMD_IDE +#define __io +#define CONFIG_CMD_EXT2 +#define CONFIG_MVSATA_IDE +#define CONFIG_IDE_PREINIT +#define CONFIG_MVSATA_IDE_USE_PORT1 +/* Needs byte-swapping for ATA data register */ +#define CONFIG_IDE_SWAP_IO +/* Data, registers and alternate blocks are at the same offset */ +#define CONFIG_SYS_ATA_DATA_OFFSET (0x0100) +#define CONFIG_SYS_ATA_REG_OFFSET (0x0100) +#define CONFIG_SYS_ATA_ALT_OFFSET (0x0100) +/* Each 8-bit ATA register is aligned to a 4-bytes address */ +#define CONFIG_SYS_ATA_STRIDE 4 +/* Controller supports 48-bits LBA addressing */ +#define CONFIG_LBA48 +/* CONFIG_CMD_IDE requires some #defines for ATA registers */ +#define CONFIG_SYS_IDE_MAXBUS 2 +#define CONFIG_SYS_IDE_MAXDEVICE 2 +/* ATA registers base is at SATA controller base */ +#define CONFIG_SYS_ATA_BASE_ADDR MV_SATA_BASE +#endif /* CONFIG_CMD_IDE */ + +/* + * I2C related stuff + */ +#ifdef CONFIG_CMD_I2C +#define CONFIG_I2C_MVTWSI +#define CONFIG_SYS_I2C_SLAVE 0x0 +#define CONFIG_SYS_I2C_SPEED 100000 +#endif + +/* + * File system + */ +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_JFFS2 +#define CONFIG_CMD_FAT +#define CONFIG_CMD_UBI +#define CONFIG_CMD_UBIFS +#define CONFIG_RBTREE +#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ +#define CONFIG_MTD_PARTITIONS +#define CONFIG_CMD_MTDPARTS +#define CONFIG_LZO + +#endif /* _MV_COMMON_H */ diff --git a/include/configs/mv88f6281gtw_ge.h b/include/configs/mv88f6281gtw_ge.h index 9ef03a68b78..d3238295f2b 100644 --- a/include/configs/mv88f6281gtw_ge.h +++ b/include/configs/mv88f6281gtw_ge.h @@ -33,66 +33,19 @@ /* * High Level Configuration Options (easy to change) */ -#define CONFIG_MARVELL 1 -#define CONFIG_ARM926EJS 1 /* Basic Architecture */ #define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */ #define CONFIG_KIRKWOOD 1 /* SOC Family Name */ #define CONFIG_KW88F6281 1 /* SOC Name */ #define CONFIG_MACH_MV88F6281GTW_GE /* Machine type */ - -#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */ #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ -#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */ -#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 for kernel */ -#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */ /* - * CLKs configurations - */ -#define CONFIG_SYS_HZ 1000 - -/* - * NS16550 Configuration - */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (-4) -#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK -#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE - -/* - * Serial Port configuration - * The following definitions let you select what serial you want to use - * for your console driver. - */ - -#define CONFIG_CONS_INDEX 1 /*Console on UART0 */ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \ - 115200,230400, 460800, 921600 } -/* auto boot */ -#define CONFIG_BOOTDELAY 3 /* default enable autoboot */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ -#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */ -#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */ - -#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */ -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ - +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */ -/* * Commands configuration */ #define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */ #include <config_cmd_default.h> -#define CONFIG_CMD_AUTOSCRIPT #define CONFIG_CMD_DHCP +#define CONFIG_CMD_PING #define CONFIG_CMD_ENV #define CONFIG_CMD_FAT #define CONFIG_CMD_PING @@ -100,17 +53,18 @@ #define CONFIG_CMD_USB /* - * Flash configuration + * mv-common.h should be defined after CMD configs since it used them + * to enable certain macros */ -#ifdef CONFIG_CMD_SF -#define CONFIG_SPI_FLASH 1 -#define CONFIG_HARD_SPI 1 -#define CONFIG_KIRKWOOD_SPI 1 -#define CONFIG_SPI_FLASH_MACRONIX 1 -#define CONFIG_ENV_SPI_BUS 0 -#define CONFIG_ENV_SPI_CS 0 -#define CONFIG_ENV_SPI_MAX_HZ 50000000 /*50Mhz */ -#endif +#include "mv-common.h" + +/* Unwanted stuffs from mv-common.h */ +#undef CONFIG_CMD_EXT2 +#undef CONFIG_CMD_JFFS2 +#undef CONFIG_CMD_FAT +#undef CONFIG_CMD_UBI +#undef CONFIG_CMD_UBIFS +#undef CONFIG_RBTREE /* * Environment variables configurations @@ -142,59 +96,11 @@ "x_bootargs_root=root=/dev/mtdblock3 ro rootfstype=squashfs\0" /* - * Size of malloc() pool - */ -#define CONFIG_SYS_MALLOC_LEN (1024 * 128) /* 128kB for malloc() */ -/* size in bytes reserved for initial data */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 - -/* - * Other required minimal configurations - */ -#define CONFIG_CONSOLE_INFO_QUIET /* some code reduction */ -#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */ -#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */ -#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */ -#define CONFIG_NR_DRAM_BANKS 4 -#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */ -#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */ -#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */ -#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */ -#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ - -/* * Ethernet Driver configuration */ #ifdef CONFIG_CMD_NET -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_PING -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_NET_MULTI /* specify more that one ports available */ -#define CONFIG_MII /* expose smi ove miiphy interface */ -#define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */ -#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */ #define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ -#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ -#endif /* CONFIG_CMD_NET */ - -/* - * Marvell 88Exxxx Switch configurations - */ -#define CONFIG_RESET_PHY_R /* use reset_phy() to init phy/swtich */ #define CONFIG_MV88E61XX_SWITCH /* Enable mv88e61xx switch driver */ - -/* - * USB/EHCI - */ -#ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI /* Enable EHCI USB support */ -#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */ -#define CONFIG_EHCI_IS_TDI -#define CONFIG_USB_STORAGE -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION -#define CONFIG_SUPPORT_VFAT -#endif /* CONFIG_CMD_USB */ +#endif /* CONFIG_CMD_NET */ #endif /* _CONFIG_MV88F6281GTW_GE_H */ diff --git a/include/configs/mx31ads.h b/include/configs/mx31ads.h index dedecd7fb6a..57955dfc3b0 100644 --- a/include/configs/mx31ads.h +++ b/include/configs/mx31ads.h @@ -63,13 +63,13 @@ #define CONFIG_HARD_SPI 1 #define CONFIG_MXC_SPI 1 #define CONFIG_DEFAULT_SPI_BUS 1 -#define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_2 | SPI_CS_HIGH) +#define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_0 | SPI_CS_HIGH) #define CONFIG_FSL_PMIC #define CONFIG_FSL_PMIC_BUS 1 #define CONFIG_FSL_PMIC_CS 0 #define CONFIG_FSL_PMIC_CLK 1000000 -#define CONFIG_FSL_PMIC_MODE (SPI_MODE_2 | SPI_CS_HIGH) +#define CONFIG_FSL_PMIC_MODE (SPI_MODE_0 | SPI_CS_HIGH) #define CONFIG_RTC_MC13783 1 /* allow to overwrite serial and ethaddr */ diff --git a/include/configs/mx31pdk.h b/include/configs/mx31pdk.h index 0414cc37a7a..4b4fb1a06a3 100644 --- a/include/configs/mx31pdk.h +++ b/include/configs/mx31pdk.h @@ -67,13 +67,13 @@ #define CONFIG_HARD_SPI 1 #define CONFIG_MXC_SPI 1 #define CONFIG_DEFAULT_SPI_BUS 1 -#define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_2 | SPI_CS_HIGH) +#define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_0 | SPI_CS_HIGH) #define CONFIG_FSL_PMIC #define CONFIG_FSL_PMIC_BUS 1 #define CONFIG_FSL_PMIC_CS 2 #define CONFIG_FSL_PMIC_CLK 1000000 -#define CONFIG_FSL_PMIC_MODE (SPI_MODE_2 | SPI_CS_HIGH) +#define CONFIG_FSL_PMIC_MODE (SPI_MODE_0 | SPI_CS_HIGH) #define CONFIG_RTC_MC13783 1 /* allow to overwrite serial and ethaddr */ diff --git a/include/configs/mx51evk.h b/include/configs/mx51evk.h index 86a4731a691..8864f3ab780 100644 --- a/include/configs/mx51evk.h +++ b/include/configs/mx51evk.h @@ -73,7 +73,7 @@ #define CONFIG_FSL_PMIC_BUS 0 #define CONFIG_FSL_PMIC_CS 0 #define CONFIG_FSL_PMIC_CLK 2500000 -#define CONFIG_FSL_PMIC_MODE (SPI_CPOL | SPI_CS_HIGH) +#define CONFIG_FSL_PMIC_MODE (SPI_MODE_0 | SPI_CS_HIGH) /* * MMC Configs diff --git a/include/configs/omap1510.h b/include/configs/omap1510.h index 931560cdcf4..e6d9c7aa79c 100644 --- a/include/configs/omap1510.h +++ b/include/configs/omap1510.h @@ -28,7 +28,7 @@ * 675 Mass Ave, Cambridge, MA 02139, USA. */ -#include <asm/arch/sizes.h> +#include <asm/sizes.h> /* There are 2 sets of general I/O --> diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h index 2463be416e0..1bd0f37add0 100644 --- a/include/configs/omap3_beagle.h +++ b/include/configs/omap3_beagle.h @@ -340,8 +340,7 @@ extern unsigned int boot_flash_sec; extern unsigned int boot_flash_type; #endif -/* additions for new relocation code, must added to all boards */ -#undef CONFIG_SYS_ARM_WITHOUT_RELOC /* This board is tested with relocation support */ +/* additions for new relocation code, must be added to all boards */ #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 #define CONFIG_SYS_INIT_SP_ADDR (LOW_LEVEL_SRAM_STACK - CONFIG_SYS_GBL_DATA_SIZE) diff --git a/include/configs/omap730.h b/include/configs/omap730.h index 04d51446efa..c7682a192ff 100644 --- a/include/configs/omap730.h +++ b/include/configs/omap730.h @@ -31,7 +31,7 @@ #ifndef __INCLUDED_OMAP730_H #define __INCLUDED_OMAP730_H -#include <asm/arch/sizes.h> +#include <asm/sizes.h> /*************************************************************************** * OMAP730 Configuration Registers diff --git a/include/configs/openrd_base.h b/include/configs/openrd_base.h index 846dfcd4846..cfdd09cda0e 100644 --- a/include/configs/openrd_base.h +++ b/include/configs/openrd_base.h @@ -38,59 +38,12 @@ /* * High Level Configuration Options (easy to change) */ -#define CONFIG_MARVELL 1 -#define CONFIG_ARM926EJS 1 /* Basic Architecture */ #define CONFIG_SHEEVA_88SV131 1 /* CPU Core subversion */ #define CONFIG_KIRKWOOD 1 /* SOC Family Name */ #define CONFIG_KW88F6281 1 /* SOC Name */ #define CONFIG_MACH_OPENRD_BASE /* Machine type */ - -#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */ #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ -#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */ -#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */ -#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 for kernel */ - -/* - * CLKs configurations - */ -#define CONFIG_SYS_HZ 1000 - -/* - * NS16550 Configuration - */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (-4) -#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK -#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE - -/* - * Serial Port configuration - * The following definitions let you select what serial you want to use - * for your console driver. - */ - -#define CONFIG_CONS_INDEX 1 /*Console on UART0 */ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \ - 115200,230400, 460800, 921600 } -/* auto boot */ -#define CONFIG_BOOTDELAY 3 /* default enable autoboot */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ -#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */ -#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */ -#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */ -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ - +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */ /* * Commands configuration */ @@ -106,15 +59,10 @@ #define CONFIG_CMD_IDE /* - * NAND configuration + * mv-common.h should be defined after CMD configs since it used them + * to enable certain macros */ -#ifdef CONFIG_CMD_NAND -#define CONFIG_NAND_KIRKWOOD -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define NAND_MAX_CHIPS 1 -#define CONFIG_SYS_NAND_BASE 0xD8000000 /* KW_DEFADR_NANDF */ -#define NAND_ALLOW_ERASE_ALL 1 -#endif +#include "mv-common.h" /* * Environment variables configurations @@ -154,97 +102,19 @@ "mtdparts="MTDPARTS_DEFAULT"\0" /* - * Size of malloc() pool - */ -#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* 1MiB for malloc() */ -/* size in bytes reserved for initial data */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 - -/* - * Other required minimal configurations - */ -#define CONFIG_SYS_LONGHELP -#define CONFIG_AUTO_COMPLETE -#define CONFIG_CMDLINE_EDITING -#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */ -#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */ -#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */ -#define CONFIG_NR_DRAM_BANKS 4 -#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */ -#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */ -#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */ -#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */ -#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ - -/* * Ethernet Driver configuration */ #ifdef CONFIG_CMD_NET -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_NET_MULTI /* specify more that one ports available */ -#define CONFIG_MII /* expose smi ove miiphy interface */ -#define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */ -#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */ #define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ #define CONFIG_PHY_BASE_ADR 0x8 -#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ -#define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */ #endif /* CONFIG_CMD_NET */ /* - * USB/EHCI - */ -#ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI /* Enable EHCI USB support */ -#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */ -#define CONFIG_EHCI_IS_TDI -#define CONFIG_USB_STORAGE -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION -#define CONFIG_SUPPORT_VFAT -#endif /* CONFIG_CMD_USB */ - -/* - * IDe Support on SATA port0 - */ -#ifdef CONFIG_CMD_IDE -#define __io -#define CONFIG_CMD_EXT2 -#define CONFIG_MVSATA_IDE -#define CONFIG_IDE_PREINIT -#define CONFIG_MVSATA_IDE_USE_PORT1 -/* Needs byte-swapping for ATA data register */ -#define CONFIG_IDE_SWAP_IO -/* Data, registers and alternate blocks are at the same offset */ -#define CONFIG_SYS_ATA_DATA_OFFSET (0x0100) -#define CONFIG_SYS_ATA_REG_OFFSET (0x0100) -#define CONFIG_SYS_ATA_ALT_OFFSET (0x0100) -/* Each 8-bit ATA register is aligned to a 4-bytes address */ -#define CONFIG_SYS_ATA_STRIDE 4 -/* Controller supports 48-bits LBA addressing */ -#define CONFIG_LBA48 -/* CONFIG_CMD_IDE requires some #defines for ATA registers */ -#define CONFIG_SYS_IDE_MAXBUS 2 -#define CONFIG_SYS_IDE_MAXDEVICE 2 -/* ATA registers base is at SATA controller base */ -#define CONFIG_SYS_ATA_BASE_ADDR KW_SATA_BASE -/* ATA bus 0 is Kirkwood port 0 on openrd */ -#define CONFIG_SYS_ATA_IDE0_OFFSET KW_SATA_PORT0_OFFSET -/* ATA bus 1 is Kirkwood port 1 on openrd */ -#define CONFIG_SYS_ATA_IDE1_OFFSET KW_SATA_PORT1_OFFSET -#endif /* CONFIG_CMD_IDE */ - -/* - * File system + * SATA Driver configuration */ -#define CONFIG_CMD_FAT -#define CONFIG_CMD_UBI -#define CONFIG_CMD_UBIFS -#define CONFIG_RBTREE -#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ -#define CONFIG_MTD_PARTITIONS -#define CONFIG_CMD_MTDPARTS -#define CONFIG_LZO +#ifdef CONFIG_MVSATA_IDE +#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET +#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET +#endif /*CONFIG_MVSATA_IDE*/ #endif /* _CONFIG_OPENRD_BASE_H */ diff --git a/include/configs/qong.h b/include/configs/qong.h index 7a68b7b97ea..7f284efe548 100644 --- a/include/configs/qong.h +++ b/include/configs/qong.h @@ -52,18 +52,18 @@ #define CONFIG_MXC_UART 1 #define CONFIG_SYS_MX31_UART1 1 -#define CONFIG_MX31_GPIO +#define CONFIG_MXC_GPIO #define CONFIG_MXC_SPI #define CONFIG_DEFAULT_SPI_BUS 1 -#define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_2 | SPI_CS_HIGH) +#define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_0 | SPI_CS_HIGH) #define CONFIG_RTC_MC13783 #define CONFIG_FSL_PMIC #define CONFIG_FSL_PMIC_BUS 1 #define CONFIG_FSL_PMIC_CS 0 #define CONFIG_FSL_PMIC_CLK 100000 -#define CONFIG_FSL_PMIC_MODE (SPI_MODE_2 | SPI_CS_HIGH) +#define CONFIG_FSL_PMIC_MODE (SPI_MODE_0 | SPI_CS_HIGH) /* FPGA */ #define CONFIG_QONG_FPGA 1 @@ -282,8 +282,7 @@ extern int qong_nand_rdy(void *chip); "mtdparts=physmap-flash.0:384k(U-Boot),128k(env1)," \ "128k(env2),2432k(kernel),13m(ramdisk),-(user)" -/* additions for new relocation code, must added to all boards */ -#undef CONFIG_SYS_ARM_WITHOUT_RELOC /* This board is tested with relocation support */ +/* additions for new relocation code, must be added to all boards */ #define CONFIG_SYS_SDRAM_BASE 0x80000000 #define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR #define CONFIG_SYS_INIT_RAM_END IRAM_SIZE diff --git a/include/configs/rd6281a.h b/include/configs/rd6281a.h index 585730111f1..60f957996ce 100644 --- a/include/configs/rd6281a.h +++ b/include/configs/rd6281a.h @@ -33,59 +33,13 @@ /* * High Level Configuration Options (easy to change) */ -#define CONFIG_MARVELL 1 -#define CONFIG_ARM926EJS 1 /* Basic Architecture */ #define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */ #define CONFIG_KIRKWOOD 1 /* SOC Family Name */ #define CONFIG_KW88F6281 1 /* SOC Name */ #define CONFIG_MACH_RD6281A /* Machine type */ - -#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */ #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ -#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */ -#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */ - -/* - * CLKs configurations - */ -#define CONFIG_SYS_HZ 1000 - -/* - * NS16550 Configuration - */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (-4) -#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK -#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE - -/* - * Serial Port configuration - * The following definitions let you select what serial you want to use - * for your console driver. - */ - -#define CONFIG_CONS_INDEX 1 /*Console on UART0 */ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \ - 115200,230400, 460800, 921600 } -/* auto boot */ -#define CONFIG_BOOTDELAY 3 /* default enable autoboot */ /* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ -#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */ -#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */ - -#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */ -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ - +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */ -/* * Commands configuration */ #define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */ @@ -97,17 +51,13 @@ #define CONFIG_CMD_NAND #define CONFIG_CMD_PING #define CONFIG_CMD_USB +#define CONFIG_CMD_IDE /* - * NAND configuration + * mv-common.h should be defined after CMD configs since it used them + * to enable certain macros */ -#ifdef CONFIG_CMD_NAND -#define CONFIG_NAND_KIRKWOOD -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define NAND_MAX_CHIPS 1 -#define CONFIG_SYS_NAND_BASE 0xD8000000 /* KW_DEFADR_NANDF */ -#define NAND_ALLOW_ERASE_ALL 1 -#endif +#include "mv-common.h" /* * Environment variables configurations @@ -143,56 +93,23 @@ "x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2\0" /* - * Size of malloc() pool - */ -#define CONFIG_SYS_MALLOC_LEN (1024 * 128) /* 128kB for malloc() */ -/* size in bytes reserved for initial data */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 - -/* - * Other required minimal configurations - */ -#define CONFIG_CONSOLE_INFO_QUIET /* some code reduction */ -#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */ -#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */ -#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */ -#define CONFIG_NR_DRAM_BANKS 4 -#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */ -#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */ -#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */ -#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */ -#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ - -/* * Ethernet Driver configuration */ #ifdef CONFIG_CMD_NET -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_NET_MULTI /* specify more that one ports available */ -#define CONFIG_MII /* expose smi ove miiphy interface */ -#define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */ #define CONFIG_MVGBE_PORTS {1, 1} /* enable both ports */ #define CONFIG_MV88E61XX_MULTICHIP_ADRMODE #define CONFIG_DIS_AUTO_NEG_SPEED_GMII /*Disable Auto speed negociation */ #define CONFIG_PHY_SPEED _1000BASET /*Force PHYspeed to 1GBPs */ #define CONFIG_PHY_BASE_ADR 0x0A -#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ -#define CONFIG_RESET_PHY_R /* use reset_phy() to init switch and PHY */ #define CONFIG_MV88E61XX_SWITCH /* Enable MV88E61XX switch driver */ #endif /* CONFIG_CMD_NET */ /* - * USB/EHCI + * SATA Driver configuration */ -#ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI /* Enable EHCI USB support */ -#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */ -#define CONFIG_EHCI_IS_TDI -#define CONFIG_USB_STORAGE -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION -#define CONFIG_SUPPORT_VFAT -#endif /* CONFIG_CMD_USB */ +#ifdef CONFIG_MVSATA_IDE +#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET +#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET +#endif /*CONFIG_MVSATA_IDE*/ #endif /* _CONFIG_RD6281A_H */ diff --git a/include/configs/sheevaplug.h b/include/configs/sheevaplug.h index c5de86eb034..83dd8ff08f2 100644 --- a/include/configs/sheevaplug.h +++ b/include/configs/sheevaplug.h @@ -33,82 +33,28 @@ /* * High Level Configuration Options (easy to change) */ -#define CONFIG_MARVELL 1 -#define CONFIG_ARM926EJS 1 /* Basic Architecture */ #define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */ #define CONFIG_KIRKWOOD 1 /* SOC Family Name */ #define CONFIG_KW88F6281 1 /* SOC Name */ #define CONFIG_MACH_SHEEVAPLUG /* Machine type */ - -#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */ #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ -#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */ -#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */ - -/* - * CLKs configurations - */ -#define CONFIG_SYS_HZ 1000 - -/* - * NS16550 Configuration - */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (-4) -#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK -#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE - -/* - * Serial Port configuration - * The following definitions let you select what serial you want to use - * for your console driver. - */ - -#define CONFIG_CONS_INDEX 1 /*Console on UART0 */ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \ - 115200,230400, 460800, 921600 } -/* auto boot */ -#define CONFIG_BOOTDELAY 3 /* default enable autoboot */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ -#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */ -#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */ - -#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */ -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ - +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */ /* * Commands configuration */ #define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */ #include <config_cmd_default.h> -#define CONFIG_CMD_AUTOSCRIPT #define CONFIG_CMD_DHCP #define CONFIG_CMD_ENV #define CONFIG_CMD_MII #define CONFIG_CMD_NAND #define CONFIG_CMD_PING #define CONFIG_CMD_USB - /* - * NAND configuration + * mv-common.h should be defined after CMD configs since it used them + * to enable certain macros */ -#ifdef CONFIG_CMD_NAND -#define CONFIG_NAND_KIRKWOOD -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define NAND_MAX_CHIPS 1 -#define CONFIG_SYS_NAND_BASE 0xD8000000 /* KW_DEFADR_NANDF */ -#define NAND_ALLOW_ERASE_ALL 1 -#endif +#include "mv-common.h" /* * Environment variables configurations @@ -144,58 +90,14 @@ "x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2\0" /* - * Size of malloc() pool - */ -#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* 1 MiB for malloc() */ -/* size in bytes reserved for initial data */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 - -/* - * Other required minimal configurations - */ -#define CONFIG_SYS_LONGHELP -#define CONFIG_AUTO_COMPLETE -#define CONFIG_CMDLINE_EDITING -#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */ -#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */ -#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */ -#define CONFIG_NR_DRAM_BANKS 4 -#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */ -#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */ -#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */ -#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */ -#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ - -/* * Ethernet Driver configuration */ #ifdef CONFIG_CMD_NET -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_NET_MULTI /* specify more that one ports available */ -#define CONFIG_MII /* expose smi ove miiphy interface */ -#define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */ -#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */ #define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ #define CONFIG_PHY_BASE_ADR 0 -#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ -#define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */ #endif /* CONFIG_CMD_NET */ /* - * USB/EHCI - */ -#ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI /* Enable EHCI USB support */ -#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */ -#define CONFIG_EHCI_IS_TDI -#define CONFIG_USB_STORAGE -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION -#define CONFIG_SUPPORT_VFAT -#endif /* CONFIG_CMD_USB */ - -/* * File system */ #define CONFIG_CMD_EXT2 diff --git a/include/configs/tx25.h b/include/configs/tx25.h index c798570aec9..bcc8140df0d 100644 --- a/include/configs/tx25.h +++ b/include/configs/tx25.h @@ -176,8 +176,7 @@ "update=nand erase 0 40000;nand write ${loadaddr} 0 40000\0" \ "upd=run load update\0" \ -/* additions for new relocation code, must added to all boards */ -#undef CONFIG_SYS_ARM_WITHOUT_RELOC /* This board is tested with relocation support */ +/* additions for new relocation code, must be added to all boards */ #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \ CONFIG_SYS_GBL_DATA_SIZE) diff --git a/include/configs/vision2.h b/include/configs/vision2.h new file mode 100644 index 00000000000..44a6f8be696 --- /dev/null +++ b/include/configs/vision2.h @@ -0,0 +1,214 @@ +/* + * Copyright (C) 2007, Guennadi Liakhovetski <lg@denx.de> + * + * (C) Copyright 2009 Freescale Semiconductor, Inc. + * + * Configuration settings for the MX51-3Stack Freescale board. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#include <asm/arch/imx-regs.h> + +#define CONFIG_MX51 /* in a mx51 */ +#define CONFIG_L2_OFF + +#define CONFIG_MX51_HCLK_FREQ 24000000 +#define CONFIG_MX51_CLK32 32768 +#define CONFIG_DISPLAY_CPUINFO +#define CONFIG_DISPLAY_BOARDINFO + +#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ +#define CONFIG_REVISION_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_INITRD_TAG +#define BOARD_LATE_INIT + +/* + * Size of malloc() pool + */ +#define CONFIG_SYS_MALLOC_LEN (2048 * 1024) + +/* size in bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_SIZE 128 + +/* + * Hardware drivers + */ +#define CONFIG_MXC_UART +#define CONFIG_SYS_MX51_UART3 +#define CONFIG_MXC_GPIO +#define CONFIG_MXC_SPI +#define CONFIG_HW_WATCHDOG + + /* + * SPI Configs + * */ +#define CONFIG_FSL_SF +#define CONFIG_CMD_SF + +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_STMICRO + +/* + * Use gpio 4 pin 25 as chip select for SPI flash + * This corresponds to gpio 121 + */ +#define CONFIG_SPI_FLASH_CS (1 | (121 << 8)) +#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 +#define CONFIG_SF_DEFAULT_SPEED 25000000 + +#define CONFIG_ENV_SPI_CS (1 | (121 << 8)) +#define CONFIG_ENV_SPI_BUS 0 +#define CONFIG_ENV_SPI_MAX_HZ 25000000 +#define CONFIG_ENV_SPI_MODE SPI_MODE_0 + +#define CONFIG_ENV_OFFSET (6 * 64 * 1024) +#define CONFIG_ENV_SECT_SIZE (1 * 64 * 1024) +#define CONFIG_ENV_SIZE (4 * 1024) + +#define CONFIG_FSL_ENV_IN_SF +#define CONFIG_ENV_IS_IN_SPI_FLASH + +/* PMIC Controller */ +#define CONFIG_FSL_PMIC +#define CONFIG_FSL_PMIC_BUS 0 +#define CONFIG_FSL_PMIC_CS 0 +#define CONFIG_FSL_PMIC_CLK 2500000 +#define CONFIG_FSL_PMIC_MODE SPI_MODE_0 +#define CONFIG_RTC_MC13783 + +/* + * MMC Configs + */ +#define CONFIG_FSL_ESDHC +#ifdef CONFIG_FSL_ESDHC +#define CONFIG_SYS_FSL_ESDHC_ADDR (0x70004000) +#define CONFIG_SYS_FSL_ESDHC_NUM 1 + +#define CONFIG_MMC + +#define CONFIG_CMD_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION +#endif + +#define CONFIG_CMD_DATE + +/* + * Eth Configs + */ +#define CONFIG_HAS_ETH1 +#define CONFIG_NET_MULTI +#define CONFIG_MII +#define CONFIG_DISCOVER_PHY + +#define CONFIG_FEC_MXC +#define IMX_FEC_BASE FEC_BASE_ADDR +#define CONFIG_FEC_MXC_PHYADDR 0x1F + +#define CONFIG_CMD_PING +#define CONFIG_CMD_MII +#define CONFIG_CMD_NET + +/* allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE +#define CONFIG_CONS_INDEX 3 +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200} + +/*********************************************************** + * Command definition + ***********************************************************/ + +#include <config_cmd_default.h> + +#define CONFIG_CMD_SPI +#undef CONFIG_CMD_IMLS + +#define CONFIG_BOOTDELAY 3 + +#define CONFIG_LOADADDR 0x90800000 /* loadaddr env var */ + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "loadaddr=0x90800000\0" + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_SYS_PROMPT "Vision II U-boot > " +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ + +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 64 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + +#define CONFIG_SYS_MEMTEST_START 0x90000000 +#define CONFIG_SYS_MEMTEST_END 0x10000 + +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR + +#define CONFIG_SYS_HZ 1000 +#define CONFIG_CMDLINE_EDITING +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "Vision II U-boot > " + +/* + * Stack sizes + */ +#define CONFIG_STACKSIZE (128 * 1024) /* regular stack */ + +/* + * Physical Memory Map + */ +#define CONFIG_NR_DRAM_BANKS 2 +#define PHYS_SDRAM_1 CSD0_BASE_ADDR +#define PHYS_SDRAM_1_SIZE (256 * 1024 * 1024) +#define PHYS_SDRAM_2 CSD1_BASE_ADDR +#define PHYS_SDRAM_2_SIZE (256 * 1024 * 1024) +#define CONFIG_SYS_SDRAM_BASE 0x90000000 +#define CONFIG_SYS_INIT_RAM_ADDR 0x1FFE8000 + +#ifndef CONFIG_SYS_ARM_WITHOUT_RELOC +#define CONFIG_SYS_INIT_RAM_END (64 * 1024) +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - \ + CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_GBL_DATA_OFFSET) +#undef CONFIG_SKIP_RELOCATE_UBOOT +#else +#define CONFIG_SKIP_RELOCATE_UBOOT +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + 0x2000) +#endif + +#define CONFIG_BOARD_EARLY_INIT_F + +/* 166 MHz DDR RAM */ +#define CONFIG_SYS_DDR_CLKSEL 0 +#define CONFIG_SYS_CLKTL_CBCDR 0x19239100 + +#define CONFIG_SYS_NO_FLASH + +#endif /* __CONFIG_H */ diff --git a/include/mc13892.h b/include/mc13892.h index b2917574121..791e3ec8784 100644 --- a/include/mc13892.h +++ b/include/mc13892.h @@ -157,4 +157,7 @@ #define VSDSTBY (1 << 19) #define VSDMODE (1 << 20) +/* Reg Power Control 2*/ +#define WDIRESET (1 << 12) + #endif diff --git a/include/mxc_gpio.h b/include/mxc_gpio.h new file mode 100644 index 00000000000..002ba61e006 --- /dev/null +++ b/include/mxc_gpio.h @@ -0,0 +1,52 @@ +/* + * + * (c) 2007 Pengutronix, Sascha Hauer <s.hauer@pengutronix.de> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __MXC_GPIO_H +#define __MXC_GPIO_H + +enum mxc_gpio_direction { + MXC_GPIO_DIRECTION_IN, + MXC_GPIO_DIRECTION_OUT, +}; + +#ifdef CONFIG_MXC_GPIO +extern int mxc_gpio_direction(unsigned int gpio, + enum mxc_gpio_direction direction); +extern void mxc_gpio_set(unsigned int gpio, unsigned int value); +extern int mxc_gpio_get(unsigned int gpio); +#else +static inline int mxc_gpio_direction(unsigned int gpio, + enum mxc_gpio_direction direction) +{ + return 1; +} +static inline int mxc_gpio_get(unsigned int gpio) +{ + return 1; +} +static inline void mxc_gpio_set(unsigned int gpio, unsigned int value) +{ +} +#endif + +#endif |