diff options
| -rw-r--r-- | board/lego/ev3/README | 36 | ||||
| -rw-r--r-- | include/configs/legoev3.h | 48 |
2 files changed, 65 insertions, 19 deletions
diff --git a/board/lego/ev3/README b/board/lego/ev3/README index a3563732499..da62a649bad 100644 --- a/board/lego/ev3/README +++ b/board/lego/ev3/README @@ -9,14 +9,34 @@ Booting ======= The EV3 contains a bootloader in EEPROM that loads u-boot.bin from address 0x0 -of the spi flash memory. Using the default configuration, u-boot will check to -see if there is a boot.scr file on the first FAT partition of the mmc. If there -is, it will run the script and boot the kernel from the uImage file also in -the FAT partition. Otherwise, it will load a kernel and rootfs from the flash. -The kernel must be stored at address 0x50000 on the flash and have a maximum -size of 4MiB. The rootfs must be a squasfs image and stored at 0x450000 in the -flash and have a maximum size of 10MiB. The flash starting at 0xE50000 is -reserved for user data. +of the SPI flash memory (with a size of 256KiB!). Because the EEPROM is read- +only and it takes care of low level configuration (PLL and DDR), we don't use +U-Boot to produce an SPL image. + +Using the default configuration, U-Boot had a boot scrips that works as follows: + +* Check to see if microSD card is present +* If it is, try to load boot.scr from the first FAT partition +* If loading boot.scr was successful, run it +* Otherwise, try loading uEnv.txt +* If loading uEnv.txt was successful, import it +* If there is a uenvcmd variable (from uEnv.txt), run it +* Try to load uImage from the first FAT partition +* If it was successful, try to load da850-lego-ev3.dtb +* If loading uImage was successful, boot it (DT is optional) +* If none of the above was successful, try booting from flash + +Suggested Flash Memory Layout +============================= + +The following is based on the default U-Boot configuration: + +| Image (file) | Start Addr. | Max. Size | ++--------------------+-------------+-------------------+ +| u-boot.bin | 0x0 | 0x40000 (256KiB) | +| da850-lego-ev3.dtb | 0x40000 | 0x10000 (64KiB) | +| uImage | 0x50000 | 0x400000 (4MiB) | +| rootfs (squashfs) | 0x450000 | 0xa00000 (10MiB) | Writing image to flash ====================== diff --git a/include/configs/legoev3.h b/include/configs/legoev3.h index 9eb95bc030f..7a0511f88e6 100644 --- a/include/configs/legoev3.h +++ b/include/configs/legoev3.h @@ -84,34 +84,60 @@ "if run loadbootscr; then " \ "run bootscript; " \ "else " \ + "if run loadbootenv; then " \ + "echo Loaded env from ${bootenvfile};" \ + "run importbootenv;" \ + "fi;" \ + "if test -n $uenvcmd; then " \ + "echo Running uenvcmd...;" \ + "run uenvcmd;" \ + "fi;" \ "if run loadimage; then " \ "run mmcargs; " \ + "if run loadfdt; then " \ + "echo Using ${fdtfile}...;" \ + "run fdtfixup; " \ + "run fdtboot; "\ + "fi; " \ "run mmcboot; " \ - "else " \ - "run flashargs; " \ - "run flashboot; " \ "fi; " \ "fi; " \ - "else " \ - "run flashargs; " \ - "run flashboot; " \ - "fi" + "fi; "\ + "run flashargs; " \ + "run flashboot" #define CONFIG_EXTRA_ENV_SETTINGS \ + "bootenvfile=uEnv.txt\0" \ + "fdtfile=da850-lego-ev3.dtb\0" \ "memsize=64M\0" \ "filesyssize=10M\0" \ "verify=n\0" \ "console=ttyS1,115200n8\0" \ "bootscraddr=0xC0600000\0" \ + "fdtaddr=0xC0600000\0" \ "loadaddr=0xC0007FC0\0" \ "filesysaddr=0xC1180000\0" \ "fwupdateboot=mw 0xFFFF1FFC 0x5555AAAA; reset\0" \ - "mmcargs=setenv bootargs mem=${memsize} console=${console} root=/dev/mmcblk0p2 rw rootwait lpj=747520\0" \ + "importbootenv=echo Importing environment...; " \ + "env import -t ${loadaddr} ${filesize}\0" \ + "loadbootenv=fatload mmc 0 ${loadaddr} ${bootenvfile}\0" \ + "mmcargs=setenv bootargs console=${console} root=/dev/mmcblk0p2 rw " \ + "rootwait ${optargs}\0" \ "mmcboot=bootm ${loadaddr}\0" \ - "flashargs=setenv bootargs mem=${memsize} initrd=${filesysaddr},${filesyssize} root=/dev/ram0 rw rootfstype=squashfs console=${console} lpj=747520\0" \ - "flashboot=sf probe 0; sf read ${loadaddr} 0x50000 0x400000; sf read ${filesysaddr} 0x450000 0xA00000; bootm ${loadaddr}\0" \ + "flashargs=setenv bootargs initrd=${filesysaddr},${filesyssize} " \ + "root=/dev/ram0 rw rootfstype=squashfs console=${console} " \ + "${optargs}\0" \ + "flashboot=sf probe 0; " \ + "sf read ${fdtaddr} 0x40000 0x10000; " \ + "sf read ${loadaddr} 0x50000 0x400000; " \ + "sf read ${filesysaddr} 0x450000 0xA00000; " \ + "run fdtfixup; " \ + "run fdtboot\0" \ "loadimage=fatload mmc 0 ${loadaddr} uImage\0" \ + "loadfdt=fatload mmc 0 ${fdtaddr} ${fdtfile}\0" \ + "fdtfixup=fdt addr ${fdtaddr}; fdt resize; fdt chosen\0" \ + "fdtboot=bootm ${loadaddr} - ${fdtaddr}\0" \ "loadbootscr=fatload mmc 0 ${bootscraddr} boot.scr\0" \ - "bootscript=source ${bootscraddr}\0" \ + "bootscript=source ${bootscraddr}\0" #ifdef CONFIG_CMD_BDI #define CONFIG_CLOCKS |