diff options
| -rw-r--r-- | board/freescale/t104xrdb/Makefile | 7 | ||||
| -rw-r--r-- | board/freescale/t104xrdb/README | 73 | ||||
| -rw-r--r-- | board/freescale/t104xrdb/ddr.c | 5 | ||||
| -rw-r--r-- | board/freescale/t104xrdb/spl.c | 122 | ||||
| -rw-r--r-- | board/freescale/t104xrdb/t1040_rcw.cfg | 7 | ||||
| -rw-r--r-- | board/freescale/t104xrdb/t1042_rcw.cfg | 7 | ||||
| -rw-r--r-- | board/freescale/t104xrdb/t104x_pbi.cfg | 26 | ||||
| -rw-r--r-- | board/freescale/t104xrdb/tlb.c | 12 | ||||
| -rw-r--r-- | boards.cfg | 6 | ||||
| -rw-r--r-- | include/configs/T104xRDB.h | 126 |
10 files changed, 371 insertions, 20 deletions
diff --git a/board/freescale/t104xrdb/Makefile b/board/freescale/t104xrdb/Makefile index 7e7bfb1c5bd..6cd304cce91 100644 --- a/board/freescale/t104xrdb/Makefile +++ b/board/freescale/t104xrdb/Makefile @@ -4,11 +4,14 @@ # SPDX-License-Identifier: GPL-2.0+ # - +ifdef CONFIG_SPL_BUILD +obj-y += spl.o +else obj-y += t104xrdb.o obj-y += cpld.o -obj-y += ddr.o obj-y += eth.o obj-$(CONFIG_PCI) += pci.o +endif +obj-y += ddr.o obj-y += law.o obj-y += tlb.o diff --git a/board/freescale/t104xrdb/README b/board/freescale/t104xrdb/README index 1da52bb0b00..cdbe1fafd9a 100644 --- a/board/freescale/t104xrdb/README +++ b/board/freescale/t104xrdb/README @@ -198,3 +198,76 @@ The below commands apply to the board 2.To change from vbank4 to vbank0 => qixis reset (it will boot using vbank0) + +NAND boot with 2 Stage boot loader +---------------------------------- +PBL initialise the internal SRAM and copy SPL(160KB) in SRAM. +SPL further initialise DDR using SPD and environment variables and copy +u-boot(768 KB) from flash to DDR. +Finally SPL transer control to u-boot for futher booting. + +SPL has following features: + - Executes within 256K + - No relocation required + + Run time view of SPL framework during boot :- + ----------------------------------------------- + Area | Address | +----------------------------------------------- + Secure boot | 0xFFFC0000 (32KB) | + headers | | + ----------------------------------------------- + GD, BD | 0xFFFC8000 (4KB) | + ----------------------------------------------- + ENV | 0xFFFC9000 (8KB) | + ----------------------------------------------- + HEAP | 0xFFFCB000 (30KB) | + ----------------------------------------------- + STACK | 0xFFFD8000 (22KB) | + ----------------------------------------------- + U-boot SPL | 0xFFFD8000 (160KB) | + ----------------------------------------------- + +NAND Flash memory Map on T104xRDB +------------------------------------------ + Start End Definition Size +0x000000 0x0FFFFF u-boot 1MB +0x180000 0x19FFFF u-boot env 128KB +0x280000 0x29FFFF FMAN Ucode 128KB +0x380000 0x39FFFF QE Firmware 128KB + +SD Card memory Map on T104xRDB +------------------------------------------ + Block #blocks Definition Size +0x008 2048 u-boot 1MB +0x800 0024 u-boot env 8KB +0x820 0256 FMAN Ucode 128KB +0x920 0256 QE Firmware 128KB + +SPI Flash memory Map on T104xRDB +------------------------------------------ + Start End Definition Size +0x000000 0x0FFFFF u-boot 1MB +0x100000 0x101FFF u-boot env 8KB +0x110000 0x12FFFF FMAN Ucode 128KB +0x130000 0x14FFFF QE Firmware 128KB + +Please note QE Firmware is only valid for T1040RDB + + +Switch Settings: (ON is 0, OFF is 1) +=============== +NAND boot SW setting: +SW1: 10001000 +SW2: 00111001 +SW3: 11110001 + +SPI boot SW setting: +SW1: 00100010 +SW2: 10111001 +SW3: 11100001 + +SD boot SW setting: +SW1: 00100000 +SW2: 00111001 +SW3: 11100001 diff --git a/board/freescale/t104xrdb/ddr.c b/board/freescale/t104xrdb/ddr.c index 57d0f9cfd86..34c9224adb6 100644 --- a/board/freescale/t104xrdb/ddr.c +++ b/board/freescale/t104xrdb/ddr.c @@ -113,6 +113,7 @@ phys_size_t initdram(int board_type) { phys_size_t dram_size; +#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL) puts("Initializing....using SPD\n"); dram_size = fsl_ddr_sdram(); @@ -120,6 +121,8 @@ phys_size_t initdram(int board_type) dram_size = setup_ddr_tlbs(dram_size / 0x100000); dram_size *= 0x100000; - puts(" DDR: "); +#else + dram_size = fsl_ddr_sdram_size(); +#endif return dram_size; } diff --git a/board/freescale/t104xrdb/spl.c b/board/freescale/t104xrdb/spl.c new file mode 100644 index 00000000000..c628c95f2d2 --- /dev/null +++ b/board/freescale/t104xrdb/spl.c @@ -0,0 +1,122 @@ +/* Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <malloc.h> +#include <ns16550.h> +#include <nand.h> +#include <i2c.h> +#include <mmc.h> +#include <fsl_esdhc.h> +#include <spi_flash.h> + +DECLARE_GLOBAL_DATA_PTR; + +phys_size_t get_effective_memsize(void) +{ + return CONFIG_SYS_L3_SIZE; +} + +unsigned long get_board_sys_clk(void) +{ + return CONFIG_SYS_CLK_FREQ; +} + +unsigned long get_board_ddr_clk(void) +{ + return CONFIG_DDR_CLK_FREQ; +} + +#define FSL_CORENET_CCSR_PORSR1_RCW_MASK 0xFF800000 +void board_init_f(ulong bootflag) +{ + u32 plat_ratio, sys_clk, uart_clk; +#ifdef CONFIG_SPL_NAND_BOOT + u32 porsr1, pinctl; +#endif + ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; + +#ifdef CONFIG_SPL_NAND_BOOT + /* + * There is T1040 SoC issue where NOR, FPGA are inaccessible during + * NAND boot because IFC signals > IFC_AD7 are not enabled. + * This workaround changes RCW source to make all signals enabled. + */ + porsr1 = in_be32(&gur->porsr1); + pinctl = ((porsr1 & ~(FSL_CORENET_CCSR_PORSR1_RCW_MASK)) | 0x24800000); + out_be32((unsigned int *)(CONFIG_SYS_DCSRBAR + 0x20000), pinctl); +#endif + + /* Memcpy existing GD at CONFIG_SPL_GD_ADDR */ + memcpy((void *)CONFIG_SPL_GD_ADDR, (void *)gd, sizeof(gd_t)); + + /* Update GD pointer */ + gd = (gd_t *)(CONFIG_SPL_GD_ADDR); + + /* compiler optimization barrier needed for GCC >= 3.4 */ + __asm__ __volatile__("" : : : "memory"); + + console_init_f(); + + /* initialize selected port with appropriate baud rate */ + sys_clk = get_board_sys_clk(); + plat_ratio = (in_be32(&gur->rcwsr[0]) >> 25) & 0x1f; + uart_clk = sys_clk * plat_ratio / 2; + + NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1, + uart_clk / 16 / CONFIG_BAUDRATE); + + relocate_code(CONFIG_SPL_RELOC_STACK, (gd_t *)CONFIG_SPL_GD_ADDR, 0x0); +} + +void board_init_r(gd_t *gd, ulong dest_addr) +{ + bd_t *bd; + + bd = (bd_t *)(gd + sizeof(gd_t)); + memset(bd, 0, sizeof(bd_t)); + gd->bd = bd; + bd->bi_memstart = CONFIG_SYS_INIT_L3_ADDR; + bd->bi_memsize = CONFIG_SYS_L3_SIZE; + + probecpu(); + get_clocks(); + mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR, + CONFIG_SPL_RELOC_MALLOC_SIZE); + +#ifdef CONFIG_SPL_MMC_BOOT + mmc_initialize(bd); +#endif + + /* relocate environment function pointers etc. */ +#ifdef CONFIG_SPL_NAND_BOOT + nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE, + (uchar *)CONFIG_ENV_ADDR); +#endif +#ifdef CONFIG_SPL_MMC_BOOT + mmc_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE, + (uchar *)CONFIG_ENV_ADDR); +#endif +#ifdef CONFIG_SPL_SPI_BOOT + spi_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE, + (uchar *)CONFIG_ENV_ADDR); +#endif + gd->env_addr = (ulong)(CONFIG_ENV_ADDR); + gd->env_valid = 1; + + i2c_init_all(); + + puts("\n\n"); + + gd->ram_size = initdram(0); + +#ifdef CONFIG_SPL_MMC_BOOT + mmc_boot(); +#elif defined(CONFIG_SPL_SPI_BOOT) + spi_boot(); +#elif defined(CONFIG_SPL_NAND_BOOT) + nand_boot(); +#endif +} diff --git a/board/freescale/t104xrdb/t1040_rcw.cfg b/board/freescale/t104xrdb/t1040_rcw.cfg new file mode 100644 index 00000000000..3300c184a1a --- /dev/null +++ b/board/freescale/t104xrdb/t1040_rcw.cfg @@ -0,0 +1,7 @@ +#PBL preamble and RCW header +aa55aa55 010e0100 +# serdes protocol 0x66 +0c18000e 0e000000 00000000 00000000 +66000002 80000002 e8106000 01000000 +00000000 00000000 00000000 00032810 +00000000 0342500f 00000000 00000000 diff --git a/board/freescale/t104xrdb/t1042_rcw.cfg b/board/freescale/t104xrdb/t1042_rcw.cfg new file mode 100644 index 00000000000..a3ea8ada56c --- /dev/null +++ b/board/freescale/t104xrdb/t1042_rcw.cfg @@ -0,0 +1,7 @@ +#PBL preamble and RCW header +aa55aa55 010e0100 +# serdes protocol 0x66 +0c18000e 0e000000 00000000 00000000 +06000002 00400002 e8106000 01000000 +00000000 00000000 00000000 00030810 +00000000 01fe0a06 00000000 00000000 diff --git a/board/freescale/t104xrdb/t104x_pbi.cfg b/board/freescale/t104xrdb/t104x_pbi.cfg new file mode 100644 index 00000000000..7b9e9b05f70 --- /dev/null +++ b/board/freescale/t104xrdb/t104x_pbi.cfg @@ -0,0 +1,26 @@ +#PBI commands +#Initialize CPC1 +09010000 00200400 +09138000 00000000 +091380c0 00000100 +#Configure CPC1 as 256KB SRAM +09010100 00000000 +09010104 fffc0007 +09010f00 08000000 +09010000 80000000 +#Configure LAW for CPC1 +09000cd0 00000000 +09000cd4 fffc0000 +09000cd8 81000011 +#Configure alternate space +09000010 00000000 +09000014 ff000000 +09000018 81000000 +#Configure SPI controller +09110000 80000403 +09110020 2d170008 +09110024 00100008 +09110028 00100008 +0911002c 00100008 +#Flush PBL data +091380c0 000FFFFF diff --git a/board/freescale/t104xrdb/tlb.c b/board/freescale/t104xrdb/tlb.c index 84f97a41e36..95c15aa5965 100644 --- a/board/freescale/t104xrdb/tlb.c +++ b/board/freescale/t104xrdb/tlb.c @@ -53,6 +53,7 @@ struct fsl_e_tlb_entry tlb_table[] = { MAS3_SX|MAS3_SR, MAS2_W|MAS2_G, 0, 2, BOOKE_PAGESZ_256M, 1), +#ifndef CONFIG_SPL_BUILD /* *I*G* - PCI */ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, @@ -82,6 +83,7 @@ struct fsl_e_tlb_entry tlb_table[] = { MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 8, BOOKE_PAGESZ_16M, 1), #endif +#endif #ifdef CONFIG_SYS_DCSRBAR_PHYS SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, @@ -102,6 +104,16 @@ struct fsl_e_tlb_entry tlb_table[] = { MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 11, BOOKE_PAGESZ_256K, 1), #endif + +#if defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SPL_BUILD) + SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 12, BOOKE_PAGESZ_1G, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000, + CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 13, BOOKE_PAGESZ_1G, 1) +#endif }; int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/boards.cfg b/boards.cfg index c01f1917fdf..95d2ccea870 100644 --- a/boards.cfg +++ b/boards.cfg @@ -945,8 +945,14 @@ Active powerpc mpc85xx - freescale t1040qds Active powerpc mpc85xx - freescale t1040qds T1040QDS_D4 T1040QDS:PPC_T1040,SYS_FSL_DDR4 Poonam Aggrwal <poonam.aggrwal@freescale.com> Active powerpc mpc85xx - freescale t1040qds T1040QDS_SECURE_BOOT T1040QDS:PPC_T1040,SECURE_BOOT Aneesh Bansal <aneesh.bansal@freescale.com> Active powerpc mpc85xx - freescale t104xrdb T1040RDB T104xRDB:PPC_T1040,T1040RDB Priyanka Jain <Priyanka.Jain@freescale.com> +Active powerpc mpc85xx - freescale t104xrdb T1040RDB_NAND T104xRDB:PPC_T1040,T1040RDB,RAMBOOT_PBL,SPL_FSL_PBL,NAND Priyanka Jain <Priyanka.Jain@freescale.com> +Active powerpc mpc85xx - freescale t104xrdb T1040RDB_SDCARD T104xRDB:PPC_T1040,T1040RDB,RAMBOOT_PBL,SPL_FSL_PBL,SDCARD Active powerpc mpc85xx - freescale t104xrdb T1040RDB_SECURE_BOOT T104xRDB:PPC_T1040,SECURE_BOOT,T1040RDB Aneesh Bansal <aneesh.bansal@freescale.com> +Active powerpc mpc85xx - freescale t104xrdb T1040RDB_SPIFLASH T104xRDB:PPC_T1040,T1040RDB,RAMBOOT_PBL,SPL_FSL_PBL,SPIFLASH Priyanka Jain <Priyanka.Jain@freescale.com> Active powerpc mpc85xx - freescale t104xrdb T1042RDB_PI T104xRDB:PPC_T1042,T1042RDB_PI Priyanka Jain <Priyanka.Jain@freescale.com> +Active powerpc mpc85xx - freescale t104xrdb T1042RDB_PI_NAND T104xRDB:PPC_T1042,T1042RDB_PI,RAMBOOT_PBL,SPL_FSL_PBL,NAND Priyanka Jain <Priyanka.Jain@freescale.com> +Active powerpc mpc85xx - freescale t104xrdb T1042RDB_PI_SDCARD T104xRDB:PPC_T1042,T1042RDB_PI,RAMBOOT_PBL,SPL_FSL_PBL,SDCARD +Active powerpc mpc85xx - freescale t104xrdb T1042RDB_PI_SPIFLASH T104xRDB:PPC_T1042,T1042RDB_PI,RAMBOOT_PBL,SPL_FSL_PBL,SPIFLASH Priyanka Jain <Priyanka.Jain@freescale.com> Active powerpc mpc85xx - freescale t208xqds T2080QDS T208xQDS:PPC_T2080 - Active powerpc mpc85xx - freescale t208xqds T2080QDS_SECURE_BOOT T208xQDS:PPC_T2080,SECURE_BOOT Aneesh Bansal <aneesh.bansal@freescale.com> Active powerpc mpc85xx - freescale t208xqds T2080QDS_NAND T208xQDS:PPC_T2080,RAMBOOT_PBL,NAND,SYS_TEXT_BASE=0xFFF40000 - diff --git a/include/configs/T104xRDB.h b/include/configs/T104xRDB.h index 8bbed7e7bf4..b3281d67d89 100644 --- a/include/configs/T104xRDB.h +++ b/include/configs/T104xRDB.h @@ -14,8 +14,79 @@ #define CONFIG_PHYS_64BIT #ifdef CONFIG_RAMBOOT_PBL -#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE -#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc +#define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/freescale/t104xrdb/t104x_pbi.cfg +#ifdef CONFIG_T1040RDB +#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/t104xrdb/t1040_rcw.cfg +#endif +#ifdef CONFIG_T1042RDB_PI +#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/t104xrdb/t1042_rcw.cfg +#endif + +#define CONFIG_SPL +#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT +#define CONFIG_SPL_ENV_SUPPORT +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_FLUSH_IMAGE +#define CONFIG_SPL_TARGET "u-boot-with-spl.bin" +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_I2C_SUPPORT +#define CONFIG_SPL_DRIVERS_MISC_SUPPORT +#define CONFIG_FSL_LAW /* Use common FSL init code */ +#define CONFIG_SYS_TEXT_BASE 0x00201000 +#define CONFIG_SPL_TEXT_BASE 0xFFFD8000 +#define CONFIG_SPL_PAD_TO 0x40000 +#define CONFIG_SPL_MAX_SIZE 0x28000 +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SPL_SKIP_RELOCATE +#define CONFIG_SPL_COMMON_INIT_DDR +#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE +#define CONFIG_SYS_NO_FLASH +#endif +#define RESET_VECTOR_OFFSET 0x27FFC +#define BOOT_PAGE_OFFSET 0x27000 + +#ifdef CONFIG_NAND +#define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10) +#define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000 +#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000 +#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) +#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" +#define CONFIG_SPL_NAND_BOOT +#endif + +#ifdef CONFIG_SPIFLASH +#define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC +#define CONFIG_SPL_SPI_SUPPORT +#define CONFIG_SPL_SPI_FLASH_SUPPORT +#define CONFIG_SPL_SPI_FLASH_MINIMAL +#define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10) +#define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x00200000) +#define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x00200000) +#define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (256 << 10) +#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" +#ifndef CONFIG_SPL_BUILD +#define CONFIG_SYS_MPC85XX_NO_RESETVEC +#endif +#define CONFIG_SPL_SPI_BOOT +#endif + +#ifdef CONFIG_SDCARD +#define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC +#define CONFIG_SPL_MMC_SUPPORT +#define CONFIG_SPL_MMC_MINIMAL +#define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10) +#define CONFIG_SYS_MMC_U_BOOT_DST (0x00200000) +#define CONFIG_SYS_MMC_U_BOOT_START (0x00200000) +#define CONFIG_SYS_MMC_U_BOOT_OFFS (260 << 10) +#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" +#ifndef CONFIG_SPL_BUILD +#define CONFIG_SYS_MPC85XX_NO_RESETVEC +#endif +#define CONFIG_SPL_MMC_BOOT +#endif + #endif /* High Level Configuration Options */ @@ -54,15 +125,12 @@ #define CONFIG_ENV_OVERWRITE -#ifdef CONFIG_SYS_NO_FLASH -#define CONFIG_ENV_IS_NOWHERE -#else +#ifndef CONFIG_SYS_NO_FLASH #define CONFIG_FLASH_CFI_DRIVER #define CONFIG_SYS_FLASH_CFI #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE #endif -#ifndef CONFIG_SYS_NO_FLASH #if defined(CONFIG_SPIFLASH) #define CONFIG_SYS_EXTRA_ENV_RELOC #define CONFIG_ENV_IS_IN_SPI_FLASH @@ -74,11 +142,11 @@ #define CONFIG_ENV_IS_IN_MMC #define CONFIG_SYS_MMC_ENV_DEV 0 #define CONFIG_ENV_SIZE 0x2000 -#define CONFIG_ENV_OFFSET (512 * 1658) +#define CONFIG_ENV_OFFSET (512 * 0x800) #elif defined(CONFIG_NAND) #define CONFIG_SYS_EXTRA_ENV_RELOC #define CONFIG_ENV_IS_IN_NAND -#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE +#define CONFIG_ENV_SIZE 0x2000 #define CONFIG_ENV_OFFSET (3 * CONFIG_SYS_NAND_BLOCK_SIZE) #else #define CONFIG_ENV_IS_IN_FLASH @@ -86,10 +154,6 @@ #define CONFIG_ENV_SIZE 0x2000 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ #endif -#else /* CONFIG_SYS_NO_FLASH */ -#define CONFIG_ENV_SIZE 0x2000 -#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ -#endif #define CONFIG_SYS_CLK_FREQ 100000000 #define CONFIG_DDR_CLK_FREQ 66666666 @@ -121,6 +185,15 @@ * Config the L3 Cache as L3 SRAM */ #define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000 +#define CONFIG_SYS_L3_SIZE 256 << 10 +#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024) +#ifdef CONFIG_RAMBOOT_PBL +#define CONFIG_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024) +#endif +#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024) +#define CONFIG_SPL_RELOC_MALLOC_SIZE (30 << 10) +#define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024) +#define CONFIG_SPL_RELOC_STACK_SIZE (22 << 10) #define CONFIG_SYS_DCSRBAR 0xf0000000 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull @@ -291,7 +364,11 @@ #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3 #endif -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE +#else +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ +#endif #if defined(CONFIG_RAMBOOT_PBL) #define CONFIG_SYS_RAMBOOT @@ -339,7 +416,9 @@ #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) #define CONFIG_SERIAL_MULTI /* Enable both serial ports */ +#ifndef CONFIG_SPL_BUILD #define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */ +#endif /* Use the HUSH parser */ #define CONFIG_SYS_HUSH_PARSER @@ -534,19 +613,32 @@ #elif defined(CONFIG_SDCARD) /* * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is - * about 825KB (1650 blocks), Env is stored after the image, and the env size is - * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680. + * about 1MB (2048 blocks), Env is stored after the image, and the env size is + * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080. */ #define CONFIG_SYS_QE_FMAN_FW_IN_MMC -#define CONFIG_SYS_FMAN_FW_ADDR (512 * 1680) +#define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820) #elif defined(CONFIG_NAND) #define CONFIG_SYS_QE_FMAN_FW_IN_NAND -#define CONFIG_SYS_FMAN_FW_ADDR (4 * CONFIG_SYS_NAND_BLOCK_SIZE) +#define CONFIG_SYS_FMAN_FW_ADDR (5 * CONFIG_SYS_NAND_BLOCK_SIZE) #else #define CONFIG_SYS_QE_FMAN_FW_IN_NOR #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 +#endif + +#ifdef CONFIG_T1040RDB +#if defined(CONFIG_SPIFLASH) +#define CONFIG_SYS_QE_FW_ADDR 0x130000 +#elif defined(CONFIG_SDCARD) +#define CONFIG_SYS_QE_FW_ADDR (512 * 0x920) +#elif defined(CONFIG_NAND) +#define CONFIG_SYS_QE_FW_ADDR (7 * CONFIG_SYS_NAND_BLOCK_SIZE) +#else #define CONFIG_SYS_QE_FW_ADDR 0xEFF10000 #endif +#endif + + #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) #endif /* CONFIG_NOBQFMAN */ |