diff options
| -rw-r--r-- | Makefile | 3 | ||||
| -rw-r--r-- | board/dave/PPChameleonEVB/nand.c | 3 | ||||
| -rw-r--r-- | board/delta/nand.c | 3 | ||||
| -rw-r--r-- | board/nc650/nand.c | 3 | ||||
| -rw-r--r-- | board/netstar/nand.c | 3 | ||||
| -rw-r--r-- | board/prodrive/pdnb3/nand.c | 3 | ||||
| -rw-r--r-- | board/tqm8272/Makefile | 40 | ||||
| -rw-r--r-- | board/tqm8272/config.mk | 34 | ||||
| -rw-r--r-- | board/tqm8272/tqm8272.c | 1236 | ||||
| -rw-r--r-- | board/tqm8272/u-boot.lds | 126 | ||||
| -rw-r--r-- | board/zylonite/nand.c | 3 | ||||
| -rw-r--r-- | cpu/mpc8260/cpu.c | 9 | ||||
| -rw-r--r-- | cpu/mpc8260/cpu_init.c | 28 | ||||
| -rw-r--r-- | cpu/mpc8260/pci.c | 19 | ||||
| -rw-r--r-- | cpu/mpc8260/speed.c | 8 | ||||
| -rw-r--r-- | cpu/ppc4xx/ndfc.c | 3 | ||||
| -rw-r--r-- | drivers/nand/nand.c | 17 | ||||
| -rw-r--r-- | drivers/nand/nand_base.c | 2 | ||||
| -rw-r--r-- | include/configs/TQM8272.h | 758 | ||||
| -rw-r--r-- | include/mpc8260.h | 10 | ||||
| -rw-r--r-- | lib_ppc/board.c | 12 |
21 files changed, 2307 insertions, 16 deletions
@@ -1536,6 +1536,9 @@ TQM8265_AA_config: unconfig fi @$(MKCONFIG) -a TQM8260 ppc mpc8260 tqm8260 +TQM8272_config: unconfig + @$(MKCONFIG) -a TQM8272 ppc mpc8260 tqm8272 + VoVPN-GW_66MHz_config \ VoVPN-GW_100MHz_config: unconfig @mkdir -p $(obj)include diff --git a/board/dave/PPChameleonEVB/nand.c b/board/dave/PPChameleonEVB/nand.c index 40a827c3e2c..f5c3dd9edc7 100644 --- a/board/dave/PPChameleonEVB/nand.c +++ b/board/dave/PPChameleonEVB/nand.c @@ -105,7 +105,7 @@ static int ppchameleonevb_device_ready(struct mtd_info *mtdinfo) * Members with a "?" were not set in the merged testing-NAND branch, * so they are not set here either. */ -void board_nand_init(struct nand_chip *nand) +int board_nand_init(struct nand_chip *nand) { nand->hwcontrol = ppchameleonevb_hwcontrol; @@ -113,5 +113,6 @@ void board_nand_init(struct nand_chip *nand) nand->eccmode = NAND_ECC_SOFT; nand->chip_delay = NAND_BIG_DELAY_US; nand->options = NAND_SAMSUNG_LP_OPTIONS; + return 0; } #endif /* (CONFIG_COMMANDS & CFG_CMD_NAND) */ diff --git a/board/delta/nand.c b/board/delta/nand.c index fe648fc1ff8..d170938c020 100644 --- a/board/delta/nand.c +++ b/board/delta/nand.c @@ -448,7 +448,7 @@ static void dfc_gpio_init(void) * Members with a "?" were not set in the merged testing-NAND branch, * so they are not set here either. */ -void board_nand_init(struct nand_chip *nand) +int board_nand_init(struct nand_chip *nand) { unsigned long tCH, tCS, tWH, tWP, tRH, tRP, tRP_high, tR, tWHR, tAR; @@ -576,6 +576,7 @@ void board_nand_init(struct nand_chip *nand) nand->cmdfunc = dfc_cmdfunc; nand->autooob = &delta_oob; nand->badblock_pattern = &delta_bbt_descr; + return 0; } #else diff --git a/board/nc650/nand.c b/board/nc650/nand.c index de54386ddd5..6bb7c314375 100644 --- a/board/nc650/nand.c +++ b/board/nc650/nand.c @@ -106,12 +106,13 @@ static void nc650_hwcontrol(struct mtd_info *mtd, int cmd) * Members with a "?" were not set in the merged testing-NAND branch, * so they are not set here either. */ -void board_nand_init(struct nand_chip *nand) +int board_nand_init(struct nand_chip *nand) { nand->hwcontrol = nc650_hwcontrol; nand->eccmode = NAND_ECC_SOFT; nand->chip_delay = 12; /* nand->options = NAND_SAMSUNG_LP_OPTIONS;*/ + return 0; } #endif /* (CONFIG_COMMANDS & CFG_CMD_NAND) */ diff --git a/board/netstar/nand.c b/board/netstar/nand.c index f470c1a01e0..78523654eb9 100644 --- a/board/netstar/nand.c +++ b/board/netstar/nand.c @@ -55,12 +55,13 @@ static int netstar_nand_ready(struct mtd_info *mtd) } ***/ -void board_nand_init(struct nand_chip *nand) +int board_nand_init(struct nand_chip *nand) { nand->options = NAND_SAMSUNG_LP_OPTIONS; nand->eccmode = NAND_ECC_SOFT; nand->hwcontrol = netstar_nand_hwcontrol; /* nand->dev_ready = netstar_nand_ready; */ nand->chip_delay = 18; + return 0; } #endif diff --git a/board/prodrive/pdnb3/nand.c b/board/prodrive/pdnb3/nand.c index 1931d64de0c..92f9c019023 100644 --- a/board/prodrive/pdnb3/nand.c +++ b/board/prodrive/pdnb3/nand.c @@ -148,7 +148,7 @@ static int pdnb3_nand_dev_ready(struct mtd_info *mtd) return 1; } -void board_nand_init(struct nand_chip *nand) +int board_nand_init(struct nand_chip *nand) { pdnb3_ndfc = (struct pdnb3_ndfc_regs *)CFG_NAND_BASE; @@ -167,5 +167,6 @@ void board_nand_init(struct nand_chip *nand) nand->read_buf = pdnb3_nand_read_buf; nand->verify_buf = pdnb3_nand_verify_buf; nand->dev_ready = pdnb3_nand_dev_ready; + return 0; } #endif diff --git a/board/tqm8272/Makefile b/board/tqm8272/Makefile new file mode 100644 index 00000000000..3dbf913d2eb --- /dev/null +++ b/board/tqm8272/Makefile @@ -0,0 +1,40 @@ +# +# (C) Copyright 2001 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = lib$(BOARD).a + +OBJS = $(BOARD).o ../tqm8xx/load_sernum_ethaddr.o + +$(LIB): .depend $(OBJS) + $(AR) crv $@ $(OBJS) + +######################################################################### + +.depend: Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c) + $(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@ + +sinclude .depend + +######################################################################### diff --git a/board/tqm8272/config.mk b/board/tqm8272/config.mk new file mode 100644 index 00000000000..af7a81e3358 --- /dev/null +++ b/board/tqm8272/config.mk @@ -0,0 +1,34 @@ +# +# (C) Copyright 2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +# +# TQM8272 boards +# + +# This should be equal to the CFG_FLASH_BASE define in config_TQM8260.h +# for the "final" configuration, with U-Boot in flash, or the address +# in RAM where U-Boot is loaded at for debugging. +# +TEXT_BASE = 0x40000000 + +PLATFORM_CPPFLAGS += -DTEXT_BASE=$(TEXT_BASE) -I$(TOPDIR) diff --git a/board/tqm8272/tqm8272.c b/board/tqm8272/tqm8272.c new file mode 100644 index 00000000000..e59e5ffedfd --- /dev/null +++ b/board/tqm8272/tqm8272.c @@ -0,0 +1,1236 @@ +/* + * (C) Copyright 2006 + * Heiko Schocher, DENX Software Engineering, hs@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <ioports.h> +#include <mpc8260.h> + +#include <command.h> +#ifdef CONFIG_PCI +#include <pci.h> +#include <asm/m8260_pci.h> +#endif +#if CONFIG_OF_FLAT_TREE +#include <ft_build.h> +#include <image.h> +#endif + +#if 0 +#define deb_printf(fmt,arg...) \ + printf ("TQM8272 %s %s: " fmt,__FILE__, __FUNCTION__, ##arg) +#else +#define deb_printf(fmt,arg...) \ + do { } while (0) +#endif + +#if defined(CONFIG_BOARD_GET_CPU_CLK_F) +unsigned long board_get_cpu_clk_f (void); +#endif + +/* + * I/O Port configuration table + * + * if conf is 1, then that port pin will be configured at boot time + * according to the five values podr/pdir/ppar/psor/pdat for that entry + */ + +const iop_conf_t iop_conf_tab[4][32] = { + + /* Port A configuration */ + { /* conf ppar psor pdir podr pdat */ + /* PA31 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 *ATMTXEN */ + /* PA30 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMTCA */ + /* PA29 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMTSOC */ + /* PA28 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 *ATMRXEN */ + /* PA27 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMRSOC */ + /* PA26 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMRCA */ + /* PA25 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMTXD[0] */ + /* PA24 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMTXD[1] */ + /* PA23 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMTXD[2] */ + /* PA22 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMTXD[3] */ + /* PA21 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMTXD[4] */ + /* PA20 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMTXD[5] */ + /* PA19 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMTXD[6] */ + /* PA18 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMTXD[7] */ + /* PA17 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMRXD[7] */ + /* PA16 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMRXD[6] */ + /* PA15 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMRXD[5] */ + /* PA14 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMRXD[4] */ + /* PA13 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMRXD[3] */ + /* PA12 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMRXD[2] */ + /* PA11 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMRXD[1] */ + /* PA10 */ { 0, 0, 0, 1, 0, 0 }, /* FCC1 ATMRXD[0] */ + /* PA9 */ { 1, 1, 0, 1, 0, 0 }, /* SMC2 TXD */ + /* PA8 */ { 1, 1, 0, 0, 0, 0 }, /* SMC2 RXD */ + /* PA7 */ { 0, 0, 0, 1, 0, 0 }, /* PA7 */ + /* PA6 */ { 0, 0, 0, 1, 0, 0 }, /* PA6 */ + /* PA5 */ { 0, 0, 0, 1, 0, 0 }, /* PA5 */ + /* PA4 */ { 0, 0, 0, 1, 0, 0 }, /* PA4 */ + /* PA3 */ { 0, 0, 0, 1, 0, 0 }, /* PA3 */ + /* PA2 */ { 0, 0, 0, 1, 0, 0 }, /* PA2 */ + /* PA1 */ { 0, 0, 0, 1, 0, 0 }, /* PA1 */ + /* PA0 */ { 0, 0, 0, 1, 0, 0 } /* PA0 */ + }, + + /* Port B configuration */ + { /* conf ppar psor pdir podr pdat */ + /* PB31 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TX_ER */ + /* PB30 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_DV */ + /* PB29 */ { 1, 1, 1, 1, 0, 0 }, /* FCC2 MII TX_EN */ + /* PB28 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_ER */ + /* PB27 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII COL */ + /* PB26 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII CRS */ + /* PB25 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[3] */ + /* PB24 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[2] */ + /* PB23 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[1] */ + /* PB22 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[0] */ + /* PB21 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[0] */ + /* PB20 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[1] */ + /* PB19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[2] */ + /* PB18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[3] */ + /* PB17 */ { 0, 0, 0, 0, 0, 0 }, /* PB17 */ + /* PB16 */ { 0, 0, 0, 0, 0, 0 }, /* PB16 */ + /* PB15 */ { 0, 0, 0, 0, 0, 0 }, /* PB15 */ + /* PB14 */ { 0, 0, 0, 0, 0, 0 }, /* PB14 */ + /* PB13 */ { 0, 0, 0, 0, 0, 0 }, /* PB13 */ + /* PB12 */ { 0, 0, 0, 0, 0, 0 }, /* PB12 */ + /* PB11 */ { 0, 0, 0, 0, 0, 0 }, /* PB11 */ + /* PB10 */ { 0, 0, 0, 0, 0, 0 }, /* PB10 */ + /* PB9 */ { 0, 0, 0, 0, 0, 0 }, /* PB9 */ + /* PB8 */ { 0, 0, 0, 0, 0, 0 }, /* PB8 */ + /* PB7 */ { 0, 0, 0, 0, 0, 0 }, /* PB7 */ + /* PB6 */ { 0, 0, 0, 0, 0, 0 }, /* PB6 */ + /* PB5 */ { 0, 0, 0, 0, 0, 0 }, /* PB5 */ + /* PB4 */ { 0, 0, 0, 0, 0, 0 }, /* PB4 */ + /* PB3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ + /* PB2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ + /* PB1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ + /* PB0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */ + }, + + /* Port C */ + { /* conf ppar psor pdir podr pdat */ + /* PC31 */ { 0, 0, 0, 1, 0, 0 }, /* PC31 */ + /* PC30 */ { 0, 0, 0, 0, 0, 0 }, /* PC30 */ + /* PC29 */ { 1, 1, 1, 0, 0, 0 }, /* SCC1 EN *CLSN */ + /* PC28 */ { 0, 0, 0, 1, 0, 0 }, /* PC28 */ + /* PC27 */ { 0, 0, 0, 1, 0, 0 }, /* PC27 */ + /* PC26 */ { 0, 0, 0, 1, 0, 0 }, /* PC26 */ + /* PC25 */ { 0, 0, 0, 1, 0, 0 }, /* PC25 */ + /* PC24 */ { 0, 0, 0, 1, 0, 0 }, /* PC24 */ + /* PC23 */ { 0, 1, 0, 1, 0, 0 }, /* ATMTFCLK */ + /* PC22 */ { 0, 1, 0, 0, 0, 0 }, /* ATMRFCLK */ + /* PC21 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 EN RXCLK */ + /* PC20 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 EN TXCLK */ + /* PC19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_CLK */ + /* PC18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII TX_CLK */ + /* PC17 */ { 1, 0, 0, 1, 0, 0 }, /* PC17 MDC */ + /* PC16 */ { 1, 0, 0, 0, 0, 0 }, /* PC16 MDIO*/ + /* PC15 */ { 0, 0, 0, 1, 0, 0 }, /* PC15 */ + /* PC14 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 EN *CD */ + /* PC13 */ { 0, 0, 0, 1, 0, 0 }, /* PC13 */ + /* PC12 */ { 0, 0, 0, 1, 0, 0 }, /* PC12 */ + /* PC11 */ { 0, 0, 0, 1, 0, 0 }, /* PC11 */ + /* PC10 */ { 0, 0, 0, 1, 0, 0 }, /* PC10 */ + /* PC9 */ { 0, 0, 0, 1, 0, 0 }, /* PC9 */ + /* PC8 */ { 0, 0, 0, 1, 0, 0 }, /* PC8 */ + /* PC7 */ { 0, 0, 0, 1, 0, 0 }, /* PC7 */ + /* PC6 */ { 0, 0, 0, 1, 0, 0 }, /* PC6 */ + /* PC5 */ { 1, 1, 0, 1, 0, 0 }, /* PC5 SMC1 TXD */ + /* PC4 */ { 1, 1, 0, 0, 0, 0 }, /* PC4 SMC1 RXD */ + /* PC3 */ { 0, 0, 0, 1, 0, 0 }, /* PC3 */ + /* PC2 */ { 0, 0, 0, 1, 0, 1 }, /* ENET FDE */ + /* PC1 */ { 0, 0, 0, 1, 0, 0 }, /* ENET DSQE */ + /* PC0 */ { 0, 0, 0, 1, 0, 0 }, /* ENET LBK */ + }, + + /* Port D */ + { /* conf ppar psor pdir podr pdat */ + /* PD31 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 EN RxD */ + /* PD30 */ { 1, 1, 1, 1, 0, 0 }, /* SCC1 EN TxD */ + /* PD29 */ { 1, 1, 0, 1, 0, 0 }, /* SCC1 EN TENA */ + /* PD28 */ { 0, 0, 0, 1, 0, 0 }, /* PD28 */ + /* PD27 */ { 0, 0, 0, 1, 0, 0 }, /* PD27 */ + /* PD26 */ { 0, 0, 0, 1, 0, 0 }, /* PD26 */ + /* PD25 */ { 0, 0, 0, 1, 0, 0 }, /* PD25 */ + /* PD24 */ { 0, 0, 0, 1, 0, 0 }, /* PD24 */ + /* PD23 */ { 0, 0, 0, 1, 0, 0 }, /* PD23 */ + /* PD22 */ { 0, 0, 0, 1, 0, 0 }, /* PD22 */ + /* PD21 */ { 0, 0, 0, 1, 0, 0 }, /* PD21 */ + /* PD20 */ { 0, 0, 0, 1, 0, 0 }, /* PD20 */ + /* PD19 */ { 0, 0, 0, 1, 0, 0 }, /* PD19 */ + /* PD18 */ { 0, 0, 0, 1, 0, 0 }, /* PD19 */ + /* PD17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXPRTY */ + /* PD16 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXPRTY */ +#if defined(CONFIG_SOFT_I2C) + /* PD15 */ { 1, 0, 0, 1, 1, 1 }, /* I2C SDA */ + /* PD14 */ { 1, 0, 0, 1, 1, 1 }, /* I2C SCL */ +#else +#if defined(CONFIG_HARD_I2C) + /* PD15 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SDA */ + /* PD14 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SCL */ +#else /* normal I/O port pins */ + /* PD15 */ { 0, 1, 1, 0, 1, 0 }, /* I2C SDA */ + /* PD14 */ { 0, 1, 1, 0, 1, 0 }, /* I2C SCL */ +#endif +#endif + /* PD13 */ { 0, 0, 0, 0, 0, 0 }, /* PD13 */ + /* PD12 */ { 0, 0, 0, 0, 0, 0 }, /* PD12 */ + /* PD11 */ { 0, 0, 0, 0, 0, 0 }, /* PD11 */ + /* PD10 */ { 0, 0, 0, 0, 0, 0 }, /* PD10 */ + /* PD9 */ { 1, 1, 0, 1, 0, 0 }, /* SMC1 TXD */ + /* PD8 */ { 1, 1, 0, 0, 0, 0 }, /* SMC1 RXD */ + /* PD7 */ { 0, 0, 0, 1, 0, 1 }, /* PD7 */ + /* PD6 */ { 0, 0, 0, 1, 0, 1 }, /* PD6 */ + /* PD5 */ { 0, 0, 0, 1, 0, 0 }, /* PD5 */ + /* PD4 */ { 0, 0, 0, 1, 0, 1 }, /* PD4 */ + /* PD3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ + /* PD2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ + /* PD1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ + /* PD0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */ + } +}; + +#define _NOT_USED_ 0xFFFFFFFF + +/* UPM pattern for bus clock = 66.7 MHz */ +static const uint upmTable67[] = +{ + /* Offset */ /* UPM Read Single RAM array entry -> NAND Read Data */ + /* 0x00 */ 0x0fa3f100, 0x0fa3b000, 0x0fa33100, 0x0fa33000, + /* 0x04 */ 0x0fa33000, 0x0fa33004, 0xfffffc01, 0xfffffc00, + + /* UPM Read Burst RAM array entry -> unused */ + /* 0x08 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x0C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + + /* UPM Read Burst RAM array entry -> unused */ + /* 0x10 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x14 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + + /* UPM Write Single RAM array entry -> NAND Write Data, ADDR and CMD */ + /* 0x18 */ 0x00a3fc00, 0x00a3fc00, 0x00a3fc00, 0x00a3fc00, + /* 0x1C */ 0x0fa3fc00, 0x0fa3fc04, 0xfffffc01, 0xfffffc00, + + /* UPM Write Burst RAM array entry -> unused */ + /* 0x20 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x24 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x28 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x2C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01, + + /* UPM Refresh Timer RAM array entry -> unused */ + /* 0x30 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x34 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x38 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01, + + /* UPM Exception RAM array entry -> unsused */ + /* 0x3C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01, +}; + +/* UPM pattern for bus clock = 100 MHz */ +static const uint upmTable100[] = +{ + /* Offset */ /* UPM Read Single RAM array entry -> NAND Read Data */ + /* 0x00 */ 0x0fa3f200, 0x0fa3b000, 0x0fa33300, 0x0fa33000, + /* 0x04 */ 0x0fa33000, 0x0fa33004, 0xfffffc01, 0xfffffc00, + + /* UPM Read Burst RAM array entry -> unused */ + /* 0x08 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x0C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + + /* UPM Read Burst RAM array entry -> unused */ + /* 0x10 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x14 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + + /* UPM Write Single RAM array entry -> NAND Write Data, ADDR and CMD */ + /* 0x18 */ 0x00a3ff00, 0x00a3fc00, 0x00a3fc00, 0x0fa3fc00, + /* 0x1C */ 0x0fa3fc00, 0x0fa3fc04, 0xfffffc01, 0xfffffc00, + + /* UPM Write Burst RAM array entry -> unused */ + /* 0x20 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x24 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x28 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x2C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01, + + /* UPM Refresh Timer RAM array entry -> unused */ + /* 0x30 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x34 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x38 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01, + + /* UPM Exception RAM array entry -> unsused */ + /* 0x3C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01, +}; + +/* UPM pattern for bus clock = 133.3 MHz */ +static const uint upmTable133[] = +{ + /* Offset */ /* UPM Read Single RAM array entry -> NAND Read Data */ + /* 0x00 */ 0x0fa3f300, 0x0fa3b000, 0x0fa33300, 0x0fa33000, + /* 0x04 */ 0x0fa33200, 0x0fa33004, 0xfffffc01, 0xfffffc00, + + /* UPM Read Burst RAM array entry -> unused */ + /* 0x08 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x0C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + + /* UPM Read Burst RAM array entry -> unused */ + /* 0x10 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x14 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + + /* UPM Write Single RAM array entry -> NAND Write Data, ADDR and CMD */ + /* 0x18 */ 0x00a3ff00, 0x00a3fc00, 0x00a3fd00, 0x0fa3fc00, + /* 0x1C */ 0x0fa3fd00, 0x0fa3fc04, 0xfffffc01, 0xfffffc00, + + /* UPM Write Burst RAM array entry -> unused */ + /* 0x20 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x24 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x28 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x2C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01, + + /* UPM Refresh Timer RAM array entry -> unused */ + /* 0x30 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x34 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x38 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01, + + /* UPM Exception RAM array entry -> unsused */ + /* 0x3C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01, +}; + +static int chipsel = 0; + +/* UPM pattern for slow init */ +static const uint upmTableSlow[] = +{ + /* Offset */ /* UPM Read Single RAM array entry */ + /* 0x00 */ 0xffffee00, 0x00ffcc80, 0x00ffcf00, 0x00ffdc00, + /* 0x04 */ 0x00ffce80, 0x00ffcc00, 0x00ffee00, 0x3fffcc07, + + /* UPM Read Burst RAM array entry -> unused */ + /* 0x08 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x0C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + + /* UPM Read Burst RAM array entry -> unused */ + /* 0x10 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x14 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + + /* UPM Write Single RAM array entry */ + /* 0x18 */ 0xffffee00, 0x00ffec80, 0x00ffef00, 0x00fffc80, + /* 0x1C */ 0x00fffe00, 0x00ffec00, 0x0fffef00, 0x3fffec05, + + /* UPM Write Burst RAM array entry -> unused */ + /* 0x20 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x24 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x28 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x2C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01, + + /* UPM Refresh Timer RAM array entry -> unused */ + /* 0x30 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x34 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x38 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01, + + /* UPM Exception RAM array entry -> unused */ + /* 0x3C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01, +}; + +/* UPM pattern for fast init */ +static const uint upmTableFast[] = +{ + /* Offset */ /* UPM Read Single RAM array entry */ + /* 0x00 */ 0xffffee00, 0x00ffcc80, 0x00ffcd80, 0x00ffdc00, + /* 0x04 */ 0x00ffdc00, 0x00ffcf00, 0x00ffec00, 0x3fffcc07, + + /* UPM Read Burst RAM array entry -> unused */ + /* 0x08 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x0C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + + /* UPM Read Burst RAM array entry -> unused */ + /* 0x10 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x14 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + + /* UPM Write Single RAM array entry */ + /* 0x18 */ 0xffffee00, 0x00ffec80, 0x00ffee80, 0x00fffc00, + /* 0x1C */ 0x00fffc00, 0x00ffec00, 0x0fffef00, 0x3fffec05, + + /* UPM Write Burst RAM array entry -> unused */ + /* 0x20 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x24 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x28 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x2C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01, + + /* UPM Refresh Timer RAM array entry -> unused */ + /* 0x30 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x34 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, + /* 0x38 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01, + + /* UPM Exception RAM array entry -> unused */ + /* 0x3C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01, +}; + + +/* ------------------------------------------------------------------------- */ + +/* Check Board Identity: + */ +int checkboard (void) +{ + char *p = (char *) HWIB_INFO_START_ADDR; + + puts ("Board: "); + if (*((unsigned long *)p) == (unsigned long)CFG_HWINFO_MAGIC) { + puts (p); + } else { + puts ("No HWIB assuming TQM8272"); + } + putc ('\n'); + + return 0; +} + +/* ------------------------------------------------------------------------- */ +#if defined(CONFIG_BOARD_GET_CPU_CLK_F) +static int get_cas_latency (void) +{ + /* get it from the option -ts in CIB */ + /* default is 3 */ + int ret = 3; + int pos = 0; + char *p = (char *) CIB_INFO_START_ADDR; + + while ((*p != '\0') && (pos < CIB_INFO_LEN)) { + if (*p < ' ' || *p > '~') { /* ASCII strings! */ + return ret; + } + if (*p == '-') { + if ((p[1] == 't') && (p[2] == 's')) { + return (p[4] - '0'); + } + } + p++; + pos++; + } + return ret; +} +#endif + +static ulong set_sdram_timing (volatile uint *sdmr_ptr, ulong sdmr, int col) +{ +#if defined(CONFIG_BOARD_GET_CPU_CLK_F) + int clk = board_get_cpu_clk_f (); + volatile immap_t *immr = (immap_t *)CFG_IMMR; + int busmode = (immr->im_siu_conf.sc_bcr & BCR_EBM ? 1 : 0); + int cas; + + sdmr = sdmr & ~(PSDMR_RFRC_MSK | PSDMR_PRETOACT_MSK | PSDMR_WRC_MSK | \ + PSDMR_BUFCMD); + if (busmode) { + switch (clk) { + case 66666666: + sdmr |= (PSDMR_RFRC_66MHZ_60X | \ + PSDMR_PRETOACT_66MHZ_60X | \ + PSDMR_WRC_66MHZ_60X | \ + PSDMR_BUFCMD_66MHZ_60X); + break; + case 100000000: + sdmr |= (PSDMR_RFRC_100MHZ_60X | \ + PSDMR_PRETOACT_100MHZ_60X | \ + PSDMR_WRC_100MHZ_60X | \ + PSDMR_BUFCMD_100MHZ_60X); + break; + + } + } else { + switch (clk) { + case 66666666: + sdmr |= (PSDMR_RFRC_66MHZ_SINGLE | \ + PSDMR_PRETOACT_66MHZ_SINGLE | \ + PSDMR_WRC_66MHZ_SINGLE | \ + PSDMR_BUFCMD_66MHZ_SINGLE); + break; + case 100000000: + sdmr |= (PSDMR_RFRC_100MHZ_SINGLE | \ + PSDMR_PRETOACT_100MHZ_SINGLE | \ + PSDMR_WRC_100MHZ_SINGLE | \ + PSDMR_BUFCMD_100MHZ_SINGLE); + break; + case 133333333: + sdmr |= (PSDMR_RFRC_133MHZ_SINGLE | \ + PSDMR_PRETOACT_133MHZ_SINGLE | \ + PSDMR_WRC_133MHZ_SINGLE | \ + PSDMR_BUFCMD_133MHZ_SINGLE); + break; + } + } + cas = get_cas_latency(); + sdmr &=~ (PSDMR_CL_MSK | PSDMR_LDOTOPRE_MSK); + sdmr |= cas; + sdmr |= ((cas - 1) << 6); + return sdmr; +#else + return sdmr; +#endif +} + +/* Try SDRAM initialization with P/LSDMR=sdmr and ORx=orx + * + * This routine performs standard 8260 initialization sequence + * and calculates the available memory size. It may be called + * several times to try different SDRAM configurations on both + * 60x and local buses. + */ +static long int try_init (volatile memctl8260_t * memctl, ulong sdmr, + ulong orx, volatile uchar * base, int col) +{ + volatile uchar c = 0xff; + volatile uint *sdmr_ptr; + volatile uint *orx_ptr; + ulong maxsize, size; + int i; + + /* We must be able to test a location outsize the maximum legal size + * to find out THAT we are outside; but this address still has to be + * mapped by the controller. That means, that the initial mapping has + * to be (at least) twice as large as the maximum expected size. + */ + maxsize = (1 + (~orx | 0x7fff)) / 2; + + /* Since CFG_SDRAM_BASE is always 0 (??), we assume that + * we are configuring CS1 if base != 0 + */ + sdmr_ptr = base ? &memctl->memc_lsdmr : &memctl->memc_psdmr; + orx_ptr = base ? &memctl->memc_or2 : &memctl->memc_or1; + + *orx_ptr = orx; + sdmr = set_sdram_timing (sdmr_ptr, sdmr, col); + /* + * Quote from 8260 UM (10.4.2 SDRAM Power-On Initialization, 10-35): + * + * "At system reset, initialization software must set up the + * programmable parameters in the memory controller banks registers + * (ORx, BRx, P/LSDMR). After all memory parameters are configured, + * system software should execute the following initialization sequence + * for each SDRAM device. + * + * 1. Issue a PRECHARGE-ALL-BANKS command + * 2. Issue eight CBR REFRESH commands + * 3. Issue a MODE-SET command to initialize the mode register + * + * The initial commands are executed by setting P/LSDMR[OP] and + * accessing the SDRAM with a single-byte transaction." + * + * The appropriate BRx/ORx registers have already been set when we + * get here. The SDRAM can be accessed at the address CFG_SDRAM_BASE. + */ + + *sdmr_ptr = sdmr | PSDMR_OP_PREA; + *base = c; + + *sdmr_ptr = sdmr | PSDMR_OP_CBRR; + for (i = 0; i < 8; i++) + *base = c; + + *sdmr_ptr = sdmr | PSDMR_OP_MRW; + *(base + CFG_MRS_OFFS) = c; /* setting MR on address lines */ + + *sdmr_ptr = sdmr | PSDMR_OP_NORM | PSDMR_RFEN; + *base = c; + + size = get_ram_size((long *)base, maxsize); + *orx_ptr = orx | ~(size - 1); + + return (size); +} + +long int initdram (int board_type) +{ + volatile immap_t *immap = (immap_t *) CFG_IMMR; + volatile memctl8260_t *memctl = &immap->im_memctl; + +#ifndef CFG_RAMBOOT + long size8, size9; +#endif + long psize, lsize; + + psize = 16 * 1024 * 1024; + lsize = 0; + + memctl->memc_psrt = CFG_PSRT; + memctl->memc_mptpr = CFG_MPTPR; + +#ifndef CFG_RAMBOOT + /* 60x SDRAM setup: + */ + size8 = try_init (memctl, CFG_PSDMR_8COL, CFG_OR1_8COL, + (uchar *) CFG_SDRAM_BASE, 8); + size9 = try_init (memctl, CFG_PSDMR_9COL, CFG_OR1_9COL, + (uchar *) CFG_SDRAM_BASE, 9); + + if (size8 < size9) { + psize = size9; + printf ("(60x:9COL - %ld MB, ", psize >> 20); + } else { + psize = try_init (memctl, CFG_PSDMR_8COL, CFG_OR1_8COL, + (uchar *) CFG_SDRAM_BASE, 8); + printf ("(60x:8COL - %ld MB, ", psize >> 20); + } + +#endif /* CFG_RAMBOOT */ + + icache_enable (); + + return (psize); +} + + +static inline int scanChar (char *p, int len, unsigned long *number) +{ + int akt = 0; + + *number = 0; + while (akt < len) + { + if ((*p >= '0') && (*p <= '9')) { + *number *= 10; + *number += *p - '0'; + p += 1; + } else { + if (*p == '-') return akt; + return -1; + } + akt ++; + } + return akt; +} + +typedef struct{ + int Bus; + int flash; + int flash_nr; + int ram; + int ram_cs; + int nand; + int nand_cs; + int eeprom; + int can; + unsigned long cpunr; + unsigned long option; + int SecEng; + int cpucl; + int cpmcl; + int buscl; + int busclk_real_ok; + int busclk_real; + unsigned char OK; + unsigned char ethaddr[20]; +} HWIB_INFO; + +HWIB_INFO hwinf = {0, 0, 1, 0, 1, 0, 0, 0, 0, 8272, 0 ,0, + 0, 0, 0, 0, 0, 0}; + +static int dump_hwib(void) +{ + HWIB_INFO *hw = &hwinf; + volatile immap_t *immr = (immap_t *)CFG_IMMR; + char *s = getenv("serial#"); + + if (hw->OK) { + printf ("HWIB on %x\n", HWIB_INFO_START_ADDR); + printf ("serial : %s\n", s); + printf ("ethaddr: %s\n", hw->ethaddr); + printf ("FLASH : %x nr:%d\n", hw->flash, hw->flash_nr); + printf ("RAM : %x cs:%d\n", hw->ram, hw->ram_cs); + printf ("CPU : %d\n", hw->cpunr); + printf ("CAN : %d\n", hw->can); + if (hw->eeprom) printf ("EEprom : %x\n", hw->eeprom); + else printf ("No EEprom\n"); + if (hw->nand) { + printf ("NAND : %x\n", hw->nand); + printf ("NAND CS: %d\n", hw->nand_cs); + } else { printf ("No NAND\n");} + printf ("Bus %s mode.\n", (hw->Bus ? "60x" : "Single PQII")); + printf (" real : %s\n", (immr->im_siu_conf.sc_bcr & BCR_EBM ? \ + "60x" : "Single PQII")); + printf ("Option : %x\n", hw->option); + printf ("%s Security Engine\n", (hw->SecEng ? "with" : "no")); + printf ("CPM Clk: %d\n", hw->cpmcl); + printf ("CPU Clk: %d\n", hw->cpucl); + printf ("Bus Clk: %d\n", hw->buscl); + if (hw->busclk_real_ok) { + printf (" real Clk: %d\n", hw->busclk_real); + } + printf ("CAS : %d\n", get_cas_latency()); + } else { + printf("HWIB @%x not OK\n", HWIB_INFO_START_ADDR); + } + return 0; +} + +static inline int search_real_busclk (int *clk) +{ + int part = 0, pos = 0; + char *p = (char *) CIB_INFO_START_ADDR; + int ok = 0; + + while ((*p != '\0') && (pos < CIB_INFO_LEN)) { + if (*p < ' ' || *p > '~') { /* ASCII strings! */ + return 0; + } + switch (part) { + default: + if (*p == '-') { + ++part; + } + break; + case 3: + if (*p == '-') { + ++part; + break; + } + if (*p == 'b') { + ok = 1; + p++; + break; + } + if (ok) { + switch (*p) { + case '6': + *clk = 66666666; + return 1; + break; + case '1': + if (p[1] == '3') { + *clk = 133333333; + } else { + *clk = 100000000; + } + return 1; + break; + } + } + break; + } + p++; + } + return 0; +} + +int analyse_hwib (void) +{ + char *p = (char *) HWIB_INFO_START_ADDR; + int anz; + int part = 1, i = 0, pos = 0; + HWIB_INFO *hw = &hwinf; + + deb_printf(" %s pointer: %p\n", __FUNCTION__, p); + /* Head = TQM */ + if (*((unsigned long *)p) != (unsigned long)CFG_HWINFO_MAGIC) { + deb_printf("No HWIB\n"); + return -1; + } + p += 3; + if (scanChar (p, 4, &hw->cpunr) < 0) { + deb_printf("No CPU\n"); + return -2; + } + p +=4; + + hw->flash = 0x200000 << (*p - 'A'); + p++; + hw->flash_nr = *p - '0'; + p++; + + hw->ram = 0x2000000 << (*p - 'A'); + p++; + if (*p == '2') { + hw->ram_cs = 2; + p++; + } + + if (*p == 'A') hw->can = 1; + if (*p == 'B') hw->can = 2; + p +=1; + p +=1; /* connector */ + if (*p != '0') { + hw->eeprom = 0x100 << (*p - 'A'); + } + p++; + + if ((*p < '0') || (*p > '9')) { + /* NAND before z-option */ + hw->nand = 0x8000000 << (*p - 'A'); + p++; + hw->nand_cs = *p - '0'; + p += 2; + } + /* z-option */ + anz = scanChar (p, 4, &hw->option); + if (anz < 0) { + deb_printf("No option\n"); + return -3; + } + if (hw->option & 0x8) hw->Bus = 1; + p += anz; + if (*p != '-') { + deb_printf("No -\n"); + return -4; + } + p++; + /* C option */ + if (*p == 'E') { + hw->SecEng = 1; + p++; + } + switch (*p) { + case 'M': hw->cpucl = 266666666; + break; + case 'P': hw->cpucl = 300000000; + break; + case 'T': hw->cpucl = 400000000; + break; + default: + deb_printf("No CPU Clk: %c\n", *p); + return -5; + break; + } + p++; + switch (*p) { + case 'I': hw->cpmcl = 200000000; + break; + case 'M': hw->cpmcl = 300000000; + break; + default: + deb_printf("No CPM Clk\n"); + return -6; + break; + } + p++; + switch (*p) { + case 'B': hw->buscl = 66666666; + break; + case 'E': hw->buscl = 100000000; + break; + case 'F': hw->buscl = 133333333; + break; + default: + deb_printf("No BUS Clk\n"); + return -7; + break; + } + p++; + + hw->OK = 1; + /* search MAC Address */ + while ((*p != '\0') && (pos < CFG_HWINFO_SIZE)) { + if (*p < ' ' || *p > '~') { /* ASCII strings! */ + return 0; + } + switch (part) { + default: + if (*p == ' ') { + ++part; + i = 0; + } + break; + case 3: /* Copy MAC address */ + if (*p == ' ') { + ++part; + i = 0; + break; + } + hw->ethaddr[i++] = *p; + if ((i % 3) == 2) + hw->ethaddr[i++] = ':'; + break; + + } + p++; + } + + hw->busclk_real_ok = search_real_busclk (&hw->busclk_real); + return 0; +} + +#if defined(CONFIG_GET_CPU_STR_F) +/* !! This routine runs from Flash */ +char get_cpu_str_f (char *buf) +{ + char *p = (char *) HWIB_INFO_START_ADDR; + int i = 0; + + buf[i++] = 'M'; + buf[i++] = 'P'; + buf[i++] = 'C'; + if (*((unsigned long *)p) == (unsigned long)CFG_HWINFO_MAGIC) { + buf[i++] = *&p[3]; + buf[i++] = *&p[4]; + buf[i++] = *&p[5]; + buf[i++] = *&p[6]; + } else { + buf[i++] = '8'; + buf[i++] = '2'; + buf[i++] = '7'; + buf[i++] = 'x'; + } + buf[i++] = 0; + return 0; +} +#endif + +#if defined(CONFIG_BOARD_GET_CPU_CLK_F) +/* !! This routine runs from Flash */ +unsigned long board_get_cpu_clk_f (void) +{ + char *p = (char *) HWIB_INFO_START_ADDR; + int i = 0; + + if (*((unsigned long *)p) == (unsigned long)CFG_HWINFO_MAGIC) { + if (search_real_busclk (&i)) + return i; + } + return CONFIG_8260_CLKIN; +} +#endif + +#if CONFIG_BOARD_EARLY_INIT_R + +static int can_test (unsigned long off) +{ + volatile unsigned char *base = (unsigned char *) (CFG_CAN_BASE + off); + + *(base + 0x17) = 'T'; + *(base + 0x18) = 'Q'; + *(base + 0x19) = 'M'; + if ((*(base + 0x17) != 'T') || + (*(base + 0x18) != 'Q') || + (*(base + 0x19) != 'M')) { + return 0; + } + return 1; +} + +static int can_config_one (unsigned long off) +{ + volatile unsigned char *ctrl = (unsigned char *) (CFG_CAN_BASE + off); + volatile unsigned char *cpu_if = (unsigned char *) (CFG_CAN_BASE + off + 0x02); + volatile unsigned char *clkout = (unsigned char *) (CFG_CAN_BASE + off + 0x1f); + unsigned char temp; + + *cpu_if = 0x45; + temp = *ctrl; + temp |= 0x40; + *ctrl = temp; + *clkout = 0x20; + temp = *ctrl; + temp &= ~0x40; + *ctrl = temp; + return 0; +} + +static int can_config (void) +{ + int ret = 0; + can_config_one (0); + if (hwinf.can == 2) { + can_config_one (0x100); + } + /* make Test if they really there */ + ret += can_test (0); + ret += can_test (0x100); + return ret; +} + +static int init_can (void) +{ + volatile immap_t * immr = (immap_t *)CFG_IMMR; + volatile memctl8260_t *memctl = &immr->im_memctl; + int count = 0; + + if ((hwinf.OK) && (hwinf.can)) { + memctl->memc_or4 = CFG_CAN_OR; + memctl->memc_br4 = CFG_CAN_BR; + /* upm Init */ + upmconfig (UPMC, (uint *) upmTableFast, + sizeof (upmTableFast) / sizeof (uint)); + memctl->memc_mcmr = (MxMR_DSx_3_CYCL | + MxMR_GPL_x4DIS | + MxMR_RLFx_2X | + MxMR_WLFx_2X | + MxMR_OP_NORM); + /* can configure */ + count = can_config (); + printf ("CAN: %d @ %x\n", count, CFG_CAN_BASE); + if (hwinf.can != count) printf("!!! difference to HWIB\n"); + } else { + printf ("CAN: No\n"); + } + return 0; +} + +int board_early_init_r(void) +{ + analyse_hwib (); + init_can (); + return 0; +} +#endif + +int do_hwib_dump (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) +{ + dump_hwib (); + return 0; +} + +U_BOOT_CMD( + hwib, 1, 1, do_hwib_dump, + "hwib - dump HWIB'\n", + "\n" +); + +#ifdef CFG_UPDATE_FLASH_SIZE +static int get_flash_timing (void) +{ + /* get it from the option -tf in CIB */ + /* default is 0x00000c84 */ + int ret = 0x00000c84; + int pos = 0; + int nr = 0; + char *p = (char *) CIB_INFO_START_ADDR; + + while ((*p != '\0') && (pos < CIB_INFO_LEN)) { + if (*p < ' ' || *p > '~') { /* ASCII strings! */ + return ret; + } + if (*p == '-') { + if ((p[1] == 't') && (p[2] == 'f')) { + p += 6; + ret = 0; + while (nr < 8) { + if ((*p >= '0') && (*p <= '9')) { + ret *= 0x10; + ret += *p - '0'; + p += 1; + nr ++; + } else if ((*p >= 'A') && (*p <= 'F')) { + ret *= 10; + ret += *p - '7'; + p += 1; + nr ++; + } else { + if (nr < 8) return 0x00000c84; + return ret; + } + } + } + } + p++; + pos++; + } + return ret; +} + +/* Update the Flash_Size and the Flash Timing */ +int update_flash_size (int flash_size) +{ + volatile immap_t * immr = (immap_t *)CFG_IMMR; + volatile memctl8260_t *memctl = &immr->im_memctl; + unsigned long reg; + unsigned long tim; + + /* I must use reg, otherwise the board hang */ + reg = memctl->memc_or0; + reg &= ~ORxU_AM_MSK; + reg |= MEG_TO_AM(flash_size >> 20); + tim = get_flash_timing (); + reg &= ~0xfff; + reg |= (tim & 0xfff); + memctl->memc_or0 = reg; + return 0; +} +#endif + +#if (CONFIG_COMMANDS & CFG_CMD_NAND) + +#include <nand.h> +#include <linux/mtd/mtd.h> + +static u8 hwctl = 0; + +static void upmnand_hwcontrol(struct mtd_info *mtdinfo, int cmd) +{ + switch (cmd) { + case NAND_CTL_SETCLE: + hwctl |= 0x1; + break; + case NAND_CTL_CLRCLE: + hwctl &= ~0x1; + break; + + case NAND_CTL_SETALE: + hwctl |= 0x2; + break; + + case NAND_CTL_CLRALE: + hwctl &= ~0x2; + break; + } +} + +static void upmnand_write_byte(struct mtd_info *mtdinfo, u_char byte) +{ + struct nand_chip *this = mtdinfo->priv; + ulong base = (ulong) (this->IO_ADDR_W + chipsel * CFG_NAND_CS_DIST); + + if (hwctl & 0x1) { + WRITE_NAND_UPM(byte, base, CFG_NAND_UPM_WRITE_CMD_OFS); + } else if (hwctl & 0x2) { + WRITE_NAND_UPM(byte, base, CFG_NAND_UPM_WRITE_ADDR_OFS); + } else { + WRITE_NAND(byte, base); + } +} + +static u_char upmnand_read_byte(struct mtd_info *mtdinfo) +{ + struct nand_chip *this = mtdinfo->priv; + ulong base = (ulong) (this->IO_ADDR_W + chipsel * CFG_NAND_CS_DIST); + + return READ_NAND(base); +} + +static int tqm8272_dev_ready(struct mtd_info *mtdinfo) +{ + /* constant delay (see also tR in the datasheet) */ + udelay(12); \ + return 1; +} + +#ifndef CONFIG_NAND_SPL +static void tqm8272_read_buf(struct mtd_info *mtdinfo, uint8_t *buf, int len) +{ + struct nand_chip *this = mtdinfo->priv; + unsigned char *base = (unsigned char *) (this->IO_ADDR_W + chipsel * CFG_NAND_CS_DIST); + int i; + + for (i = 0; i< len; i++) + buf[i] = *base; +} + +static void tqm8272_write_buf(struct mtd_info *mtdinfo, const uint8_t *buf, int len) +{ + struct nand_chip *this = mtdinfo->priv; + unsigned char *base = (unsigned char *) (this->IO_ADDR_W + chipsel * CFG_NAND_CS_DIST); + int i; + + for (i = 0; i< len; i++) + *base = buf[i]; +} + +static int tqm8272_verify_buf(struct mtd_info *mtdinfo, const uint8_t *buf, int len) +{ + struct nand_chip *this = mtdinfo->priv; + unsigned char *base = (unsigned char *) (this->IO_ADDR_W + chipsel * CFG_NAND_CS_DIST); + int i; + + for (i = 0; i < len; i++) + if (buf[i] != *base) + return -1; + return 0; +} +#endif /* #ifndef CONFIG_NAND_SPL */ + +void board_nand_select_device(struct nand_chip *nand, int chip) +{ + chipsel = chip; +} + +int board_nand_init(struct nand_chip *nand) +{ + static int UpmInit = 0; + volatile immap_t * immr = (immap_t *)CFG_IMMR; + volatile memctl8260_t *memctl = &immr->im_memctl; + + if (hwinf.nand == 0) return -1; + + /* Setup the UPM */ + if (UpmInit == 0) { + switch (hwinf.busclk_real) { + case 100000000: + upmconfig (UPMB, (uint *) upmTable100, + sizeof (upmTable100) / sizeof (uint)); + break; + case 133333333: + upmconfig (UPMB, (uint *) upmTable133, + sizeof (upmTable133) / sizeof (uint)); + break; + default: + upmconfig (UPMB, (uint *) upmTable67, + sizeof (upmTable67) / sizeof (uint)); + break; + } + UpmInit = 1; + } + + /* Setup the memctrl */ + memctl->memc_or3 = CFG_NAND_OR; + memctl->memc_br3 = CFG_NAND_BR; + memctl->memc_mbmr = (MxMR_OP_NORM); + + nand->eccmode = NAND_ECC_SOFT; + + nand->hwcontrol = upmnand_hwcontrol; + nand->read_byte = upmnand_read_byte; + nand->write_byte = upmnand_write_byte; + nand->dev_ready = tqm8272_dev_ready; + +#ifndef CONFIG_NAND_SPL + nand->write_buf = tqm8272_write_buf; + nand->read_buf = tqm8272_read_buf; + nand->verify_buf = tqm8272_verify_buf; +#endif + + /* + * Select required NAND chip + */ + board_nand_select_device(nand, 0); + return 0; +} + +#endif /* CFG_CMD_NAND */ + +#ifdef CONFIG_PCI +struct pci_controller hose; + +int board_early_init_f (void) +{ + volatile immap_t *immap = (immap_t *) CFG_IMMR; + + immap->im_clkrst.car_sccr |= M826X_SCCR_PCI_MODE_EN; + return 0; +} + +extern void pci_mpc8250_init(struct pci_controller *); + +void pci_init_board(void) +{ + pci_mpc8250_init(&hose); +} +#endif + diff --git a/board/tqm8272/u-boot.lds b/board/tqm8272/u-boot.lds new file mode 100644 index 00000000000..05f29c6ed08 --- /dev/null +++ b/board/tqm8272/u-boot.lds @@ -0,0 +1,126 @@ +/* + * (C) Copyright 2001 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc) +SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib); +/* Do we need any of these for elf? + __DYNAMIC = 0; */ +SECTIONS +{ + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + cpu/mpc8260/start.o (.text) + *(.text) + common/environment.o(.text) + *(.fixup) + *(.got1) + . = ALIGN(16); + *(.rodata) + *(.rodata1) + *(.rodata.str1.4) + *(.eh_frame) + } + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x0FFF) & 0xFFFFF000; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2; + __fixup_entries = (. - _FIXUP_TABLE_) >> 2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + + . = .; + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(4096); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(4096); + __init_end = .; + + __bss_start = .; + .bss : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } + _end = . ; + PROVIDE (end = .); +} diff --git a/board/zylonite/nand.c b/board/zylonite/nand.c index 5d2cd6585f6..a41714351f0 100644 --- a/board/zylonite/nand.c +++ b/board/zylonite/nand.c @@ -448,7 +448,7 @@ static void dfc_gpio_init(void) * Members with a "?" were not set in the merged testing-NAND branch, * so they are not set here either. */ -void board_nand_init(struct nand_chip *nand) +int board_nand_init(struct nand_chip *nand) { unsigned long tCH, tCS, tWH, tWP, tRH, tRP, tRP_high, tR, tWHR, tAR; @@ -576,6 +576,7 @@ void board_nand_init(struct nand_chip *nand) nand->cmdfunc = dfc_cmdfunc; nand->autooob = &delta_oob; nand->badblock_pattern = &delta_bbt_descr; + return 0; } #else diff --git a/cpu/mpc8260/cpu.c b/cpu/mpc8260/cpu.c index 4f23012b729..94651dc4a69 100644 --- a/cpu/mpc8260/cpu.c +++ b/cpu/mpc8260/cpu.c @@ -49,6 +49,10 @@ DECLARE_GLOBAL_DATA_PTR; +#if defined(CONFIG_GET_CPU_STR_F) +extern int get_cpu_str_f (char *buf); +#endif + int checkcpu (void) { volatile immap_t *immap = (immap_t *) CFG_IMMR; @@ -81,7 +85,12 @@ int checkcpu (void) if ((immr & IMMR_ISB_MSK) != CFG_IMMR) return -1; /* whoops! someone moved the IMMR */ +#if defined(CONFIG_GET_CPU_STR_F) + get_cpu_str_f (buf); + printf ("%s (HiP%d Rev %02x, Mask ", buf, k, rev); +#else printf (CPU_ID_STR " (HiP%d Rev %02x, Mask ", k, rev); +#endif /* * the bottom 16 bits of the immr are the Part Number and Mask Number diff --git a/cpu/mpc8260/cpu_init.c b/cpu/mpc8260/cpu_init.c index 640026be5ac..7dcc94999dc 100644 --- a/cpu/mpc8260/cpu_init.c +++ b/cpu/mpc8260/cpu_init.c @@ -28,6 +28,10 @@ DECLARE_GLOBAL_DATA_PTR; +#if defined(CONFIG_BOARD_GET_CPU_CLK_F) +extern unsigned long board_get_cpu_clk_f (void); +#endif + static void config_8260_ioports (volatile immap_t * immr) { int portnum; @@ -90,6 +94,7 @@ static void config_8260_ioports (volatile immap_t * immr) } } +#define SET_VAL_MASK(a, b, mask) ((a & mask) | (b & ~mask)) /* * Breath some life into the CPU... * @@ -102,6 +107,9 @@ void cpu_init_f (volatile immap_t * immr) #if !defined(CONFIG_COGENT) /* done in start.S for the cogent */ uint sccr; #endif +#if defined(CONFIG_BOARD_GET_CPU_CLK_F) + unsigned long cpu_clk; +#endif volatile memctl8260_t *memctl = &immr->im_memctl; extern void m8260_cpm_reset (void); @@ -119,10 +127,27 @@ void cpu_init_f (volatile immap_t * immr) immr->im_clkrst.car_rmr = CFG_RMR; /* BCR - Bus Configuration Register (4-25) */ +#if defined(CFG_BCR_60x) && (CFG_BCR_SINGLE) + if (immr->im_siu_conf.sc_bcr & BCR_EBM) { + immr->im_siu_conf.sc_bcr = CFG_BCR_60x; + } else { + immr->im_siu_conf.sc_bcr = CFG_BCR_SINGLE; + } +#else immr->im_siu_conf.sc_bcr = CFG_BCR; +#endif /* SIUMCR - contains debug pin configuration (4-31) */ +#if defined(CFG_SIUMCR_LOW) && (CFG_SIUMCR_HIGH) + cpu_clk = board_get_cpu_clk_f (); + if (cpu_clk >= 100000000) { + immr->im_siu_conf.sc_siumcr = CFG_SIUMCR_HIGH; + } else { + immr->im_siu_conf.sc_siumcr = CFG_SIUMCR_LOW; + } +#else immr->im_siu_conf.sc_siumcr = CFG_SIUMCR; +#endif config_8260_ioports (immr); @@ -157,7 +182,8 @@ void cpu_init_f (volatile immap_t * immr) #endif /* now restrict to preliminary range */ - memctl->memc_br0 = CFG_BR0_PRELIM; + /* the PS came from the HRCW, don´t change it */ + memctl->memc_br0 = SET_VAL_MASK(memctl->memc_br0 , CFG_BR0_PRELIM, BRx_PS_MSK); memctl->memc_or0 = CFG_OR0_PRELIM; #if defined(CFG_BR1_PRELIM) && defined(CFG_OR1_PRELIM) diff --git a/cpu/mpc8260/pci.c b/cpu/mpc8260/pci.c index b14fc159be3..1edd6fb8ddd 100644 --- a/cpu/mpc8260/pci.c +++ b/cpu/mpc8260/pci.c @@ -274,7 +274,23 @@ void pci_mpc8250_init (struct pci_controller *hose) | SIUMCR_CS10PC00 | SIUMCR_BCTLC00 | SIUMCR_MMR11; - +#elif defined(CONFIG_TQM8272) +#if 0 + immap->im_siu_conf.sc_siumcr = (immap->im_siu_conf.sc_siumcr & + ~SIUMCR_LBPC11 & + ~SIUMCR_CS10PC11 & + ~SIUMCR_LBPC11) | + SIUMCR_LBPC01 | + SIUMCR_CS10PC01 | + SIUMCR_APPC10; +#else +#if 0 + immap->im_siu_conf.sc_siumcr = (immap->im_siu_conf.sc_siumcr | + SIUMCR_APPC10); +#else + immap->im_siu_conf.sc_siumcr = 0x88000000; +#endif +#endif #else /* * Setting required to enable IRQ1-IRQ7 (SIUMCR [DPPC]), @@ -288,6 +304,7 @@ void pci_mpc8250_init (struct pci_controller *hose) SIUMCR_CS10PC01 | SIUMCR_APPC10; #endif +printf("%s siumcr: %x\n", __FUNCTION__, immap->im_siu_conf.sc_siumcr); /* Make PCI lowest priority */ /* Each 4 bits is a device bus request and the MS 4bits diff --git a/cpu/mpc8260/speed.c b/cpu/mpc8260/speed.c index 360404f0cfd..38cd0d9a70f 100644 --- a/cpu/mpc8260/speed.c +++ b/cpu/mpc8260/speed.c @@ -25,6 +25,10 @@ #include <mpc8260.h> #include <asm/processor.h> +#if defined(CONFIG_BOARD_GET_CPU_CLK_F) +extern unsigned long board_get_cpu_clk_f (void); +#endif + DECLARE_GLOBAL_DATA_PTR; /* ------------------------------------------------------------------------- */ @@ -112,8 +116,12 @@ int get_clocks (void) #if !defined(CONFIG_8260_CLKIN) #error clock measuring not implemented yet - define CONFIG_8260_CLKIN #else +#if defined(CONFIG_BOARD_GET_CPU_CLK_F) + clkin = board_get_cpu_clk_f (); +#else clkin = CONFIG_8260_CLKIN; #endif +#endif sccr = immap->im_clkrst.car_sccr; dfbrg = (sccr & SCCR_DFBRG_MSK) >> SCCR_DFBRG_SHIFT; diff --git a/cpu/ppc4xx/ndfc.c b/cpu/ppc4xx/ndfc.c index 352173128de..b198ff46ceb 100644 --- a/cpu/ppc4xx/ndfc.c +++ b/cpu/ppc4xx/ndfc.c @@ -156,7 +156,7 @@ void board_nand_select_device(struct nand_chip *nand, int chip) out32(base + NDFC_CCR, 0x00000000 | (cs << 24)); } -void board_nand_init(struct nand_chip *nand) +int board_nand_init(struct nand_chip *nand) { int cs = (ulong)nand->IO_ADDR_W & 0x00000003; ulong base = (ulong)nand->IO_ADDR_W & 0xfffffffc; @@ -188,6 +188,7 @@ void board_nand_init(struct nand_chip *nand) */ board_nand_select_device(nand, cs); out32(base + NDFC_BCFG0 + (cs << 2), 0x80002222); + return 0; } #endif diff --git a/drivers/nand/nand.c b/drivers/nand/nand.c index 3899045a72c..9fef71d6293 100644 --- a/drivers/nand/nand.c +++ b/drivers/nand/nand.c @@ -39,7 +39,7 @@ static ulong base_address[CFG_MAX_NAND_DEVICE] = CFG_NAND_BASE_LIST; static const char default_nand_name[] = "nand"; -extern void board_nand_init(struct nand_chip *nand); +extern int board_nand_init(struct nand_chip *nand); static void nand_init_chip(struct mtd_info *mtd, struct nand_chip *nand, ulong base_addr) @@ -47,13 +47,16 @@ static void nand_init_chip(struct mtd_info *mtd, struct nand_chip *nand, mtd->priv = nand; nand->IO_ADDR_R = nand->IO_ADDR_W = (void __iomem *)base_addr; - board_nand_init(nand); - - if (nand_scan(mtd, 1) == 0) { - if (!mtd->name) - mtd->name = (char *)default_nand_name; - } else + if (board_nand_init(nand) == 0) { + if (nand_scan(mtd, 1) == 0) { + if (!mtd->name) + mtd->name = (char *)default_nand_name; + } else + mtd->name = NULL; + } else { mtd->name = NULL; + mtd->size = 0; + } } diff --git a/drivers/nand/nand_base.c b/drivers/nand/nand_base.c index b7a5d32fb3f..95d6e4ede6a 100644 --- a/drivers/nand/nand_base.c +++ b/drivers/nand/nand_base.c @@ -2407,7 +2407,9 @@ int nand_scan (struct mtd_info *mtd, int maxchips) } if (!nand_flash_ids[i].name) { +#if !defined(CONFIG_TQM8272) printk (KERN_WARNING "No NAND device found!!!\n"); +#endif this->select_chip(mtd, -1); return 1; } diff --git a/include/configs/TQM8272.h b/include/configs/TQM8272.h new file mode 100644 index 00000000000..0f62755d772 --- /dev/null +++ b/include/configs/TQM8272.h @@ -0,0 +1,758 @@ +/* + * (C) Copyright 2006 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC8260 1 /* This is a MPC8260 CPU */ +#define CONFIG_MPC8272_FAMILY 1 +#define CONFIG_TQM8272 1 + +#define CONFIG_GET_CPU_STR_F 1 /* Get the CPU ID STR */ +#define CONFIG_BOARD_GET_CPU_CLK_F 1 /* Get the CLKIN from board fct */ + +#define STK82xx_150 1 /* on a STK82xx.150 */ + +#define CONFIG_CPM2 1 /* Has a CPM2 */ + +#define CONFIG_82xx_CONS_SMC1 1 /* console on SMC1 */ + +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +#define CONFIG_BOARD_EARLY_INIT_R 1 + +#if defined(CONFIG_CONS_NONE) || defined(CONFIG_CONS_USE_EXTC) +#define CONFIG_BAUDRATE 230400 +#else +#define CONFIG_BAUDRATE 115200 +#endif + +#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo" + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "consdev=ttyCPM0\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "hostname=tqm8272\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addcons=setenv bootargs ${bootargs} " \ + "console=$(consdev),$(baudrate)\0" \ + "flash_nfs=run nfsargs addip addcons;" \ + "bootm ${kernel_addr}\0" \ + "flash_self=run ramargs addip addcons;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "net_nfs=tftp 300000 ${bootfile};" \ + "run nfsargs addip addcons;bootm\0" \ + "rootpath=/opt/eldk/ppc_82xx\0" \ + "bootfile=/tftpboot/tqm8272/uImage\0" \ + "kernel_addr=40080000\0" \ + "ramdisk_addr=40100000\0" \ + "load=tftp 300000 /tftpboot/tqm8272/u-boot.bin\0" \ + "update=protect off 40000000 4003ffff;era 40000000 4003ffff;" \ + "cp.b 300000 40000000 40000;" \ + "setenv filesize;saveenv\0" \ + "cphwib=cp.b 4003fc00 33fc00 400\0" \ + "upd=run load;run cphwib;run update\0" \ + "" +#define CONFIG_BOOTCOMMAND "run flash_self" + +#define CONFIG_I2C 1 + +#if CONFIG_I2C +/* enable I2C and select the hardware/software driver */ +#undef CONFIG_HARD_I2C /* I2C with hardware support */ +#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ +#define ADD_CMD_I2C CFG_CMD_I2C | \ + CFG_CMD_DATE |\ + CFG_CMD_DTT |\ + CFG_CMD_EEPROM +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F + +/* + * Software (bit-bang) I2C driver configuration + */ +#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */ +#define I2C_ACTIVE (iop->pdir |= 0x00010000) +#define I2C_TRISTATE (iop->pdir &= ~0x00010000) +#define I2C_READ ((iop->pdat & 0x00010000) != 0) +#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \ + else iop->pdat &= ~0x00010000 +#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \ + else iop->pdat &= ~0x00020000 +#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ + +#define CONFIG_I2C_X + +/* EEPROM */ +#define CFG_I2C_EEPROM_ADDR_LEN 2 +#define CFG_EEPROM_PAGE_WRITE_BITS 4 +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ +#define CFG_EEPROM_PAGE_WRITE_ENABLE /* necessary for the LM75 chip */ +#define CFG_I2C_MULTI_EEPROMS 1 /* more than one eeprom */ + +/* I2C RTC */ +#define CONFIG_RTC_DS1337 /* Use ds1337 rtc via i2c */ +#define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */ + +/* I2C SYSMON (LM75) */ +#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ +#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ +#define CFG_DTT_MAX_TEMP 70 +#define CFG_DTT_LOW_TEMP -30 +#define CFG_DTT_HYSTERESIS 3 + +#else +#undef CONFIG_HARD_I2C +#undef CONFIG_SOFT_I2C +#define ADD_CMD_I2C 0 +#endif + +/* + * select serial console configuration + * + * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then + * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 + * for SCC). + * + * if CONFIG_CONS_NONE is defined, then the serial console routines must + * defined elsewhere (for example, on the cogent platform, there are serial + * ports on the motherboard which are used for the serial console - see + * cogent/cma101/serial.[ch]). + */ +#define CONFIG_CONS_ON_SMC /* define if console on SMC */ +#undef CONFIG_CONS_ON_SCC /* define if console on SCC */ +#undef CONFIG_CONS_NONE /* define if console on something else*/ +#ifdef CONFIG_82xx_CONS_SMC1 +#define CONFIG_CONS_INDEX 1 /* which serial channel for console */ +#endif +#ifdef CONFIG_82xx_CONS_SMC2 +#define CONFIG_CONS_INDEX 2 /* which serial channel for console */ +#endif + +#undef CONFIG_CONS_USE_EXTC /* SMC/SCC use ext clock not brg_clk */ +#define CONFIG_CONS_EXTC_RATE 3686400 /* SMC/SCC ext clk rate in Hz */ +#define CONFIG_CONS_EXTC_PINSEL 0 /* pin select 0=CLK3/CLK9 */ + +/* + * select ethernet configuration + * + * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then + * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3 + * for FCC) + * + * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be + * defined elsewhere (as for the console), or CFG_CMD_NET must be removed + * from CONFIG_COMMANDS to remove support for networking. + * + * (On TQM8272 either SCC1 or FCC2 may be chosen: SCC1 is hardwired to the + * X.29 connector, and FCC2 is hardwired to the X.1 connector) + */ +#define CFG_FCC_ETHERNET + +#if defined(CFG_FCC_ETHERNET) +#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */ +#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */ +#undef CONFIG_ETHER_NONE /* define if ether on something else */ +#define CONFIG_ETHER_INDEX 2 /* which SCC/FCC channel for ethernet */ +#else +#define CONFIG_ETHER_ON_SCC /* define if ether on SCC */ +#undef CONFIG_ETHER_ON_FCC /* define if ether on FCC */ +#undef CONFIG_ETHER_NONE /* define if ether on something else */ +#define CONFIG_ETHER_INDEX 1 /* which SCC/FCC channel for ethernet */ +#endif + +#if defined(CONFIG_ETHER_ON_SCC) && (CONFIG_ETHER_INDEX == 1) + +/* + * - RX clk is CLK11 + * - TX clk is CLK12 + */ +# define CFG_CMXSCR_VALUE (CMXSCR_RS1CS_CLK11 | CMXSCR_TS1CS_CLK12) + +#elif defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 2) + +/* + * - Rx-CLK is CLK13 + * - Tx-CLK is CLK14 + * - RAM for BD/Buffers is on the 60x Bus (see 28-13) + * - Enable Full Duplex in FSMR + */ +# define CFG_CMXFCR_MASK (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK) +# define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14) +# define CFG_CPMFCR_RAMTYPE 0 +# define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB) + +#endif /* CONFIG_ETHER_ON_FCC, CONFIG_ETHER_INDEX */ + +#define CONFIG_MII /* MII PHY management */ +#define CONFIG_BITBANGMII /* bit-bang MII PHY management */ +/* + * GPIO pins used for bit-banged MII communications + */ +#define MDIO_PORT 2 /* Port C */ + +#if STK82xx_150 +#define CFG_MDIO_PIN 0x00008000 /* PC16 */ +#define CFG_MDC_PIN 0x00004000 /* PC17 */ +#endif + +#if STK82xx_100 +#define CFG_MDIO_PIN 0x00000002 /* PC30 */ +#define CFG_MDC_PIN 0x00000001 /* PC31 */ +#endif + +#if 1 +#define MDIO_ACTIVE (iop->pdir |= CFG_MDIO_PIN) +#define MDIO_TRISTATE (iop->pdir &= ~CFG_MDIO_PIN) +#define MDIO_READ ((iop->pdat & CFG_MDIO_PIN) != 0) + +#define MDIO(bit) if(bit) iop->pdat |= CFG_MDIO_PIN; \ + else iop->pdat &= ~CFG_MDIO_PIN + +#define MDC(bit) if(bit) iop->pdat |= CFG_MDC_PIN; \ + else iop->pdat &= ~CFG_MDC_PIN +#else +#define MDIO_ACTIVE ({unsigned long tmp; tmp = iop->pdir; tmp |= CFG_MDIO_PIN; iop->pdir = tmp;}) +#define MDIO_TRISTATE ({unsigned long tmp; tmp = iop->pdir; tmp &= ~CFG_MDIO_PIN; iop->pdir = tmp;}) +#define MDIO_READ ((iop->pdat & CFG_MDIO_PIN) != 0) + +#define MDIO(bit) if(bit) {unsigned long tmp; tmp = iop->pdat; tmp |= CFG_MDIO_PIN; iop->pdat = tmp;}\ + else {unsigned long tmp; tmp = iop->pdat; tmp &= ~CFG_MDIO_PIN; iop->pdat = tmp;} + +#define MDC(bit) if(bit) {unsigned long tmp; tmp = iop->pdat; tmp |= CFG_MDC_PIN; iop->pdat = tmp;}\ + else {unsigned long tmp; tmp = iop->pdat; tmp &= ~CFG_MDC_PIN; iop->pdat = tmp;} +#endif + +#define MIIDELAY udelay(1) + + + +/* system clock rate (CLKIN) - equal to the 60x and local bus speed */ +#define CONFIG_8260_CLKIN 66666666 /* in Hz */ + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_TIMESTAMP /* Print image info with timestamp */ + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT|CONFIG_BOOTP_BOOTFILESIZE) + +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ + CFG_CMD_NAND | \ + CFG_CMD_DHCP | \ + CFG_CMD_PING | \ + ADD_CMD_I2C | \ + CFG_CMD_NFS | \ + CFG_CMD_MII | \ + CFG_CMD_PCI | \ + CFG_CMD_SNTP ) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ + +#if 0 +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CFG_HUSH_PARSER 1 /* Use the HUSH parser */ +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#endif +#endif + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x300000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +#define CFG_RESET_ADDRESS 0x40000104 /* "bad" address */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * CAN stuff + *----------------------------------------------------------------------- + */ +#define CFG_CAN_BASE 0x51000000 +#define CFG_CAN_SIZE 1 +#define CFG_CAN_BR ((CFG_CAN_BASE & BRx_BA_MSK) |\ + BRx_PS_8 |\ + BRx_MS_UPMC |\ + BRx_V) + +#define CFG_CAN_OR (MEG_TO_AM(CFG_CAN_SIZE) |\ + ORxU_BI) + + +/* What should the base address of the main FLASH be and how big is + * it (in MBytes)? This must contain TEXT_BASE from board/tqm8272/config.mk + * The main FLASH is whichever is connected to *CS0. + */ +#define CFG_FLASH0_BASE 0x40000000 +#define CFG_FLASH0_SIZE 32 /* 32 MB */ + +/* Flash bank size (for preliminary settings) + */ +#define CFG_FLASH_SIZE CFG_FLASH0_SIZE + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* max num of memory banks */ +#define CFG_MAX_FLASH_SECT 128 /* max num of sects on one chip */ + +#define CFG_FLASH_CFI /* flash is CFI compat. */ +#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver*/ +#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector */ +#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash*/ + +#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ + +#define CFG_UPDATE_FLASH_SIZE + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x40000) +#define CFG_ENV_SIZE 0x20000 +#define CFG_ENV_SECT_SIZE 0x20000 +#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR + CFG_ENV_SIZE) +#define CFG_ENV_SIZE_REDUND 0x20000 + +/* Where is the Hardwareinformation Block (from Monitor Sources) */ +#define MON_RES_LENGTH (0x0003FC00) +#define HWIB_INFO_START_ADDR (CFG_FLASH_BASE + MON_RES_LENGTH) +#define HWIB_INFO_LEN 512 +#define CIB_INFO_START_ADDR (CFG_FLASH_BASE + MON_RES_LENGTH + HWIB_INFO_LEN) +#define CIB_INFO_LEN 512 + +#define CFG_HWINFO_OFFSET 0x3fc00 /* offset of HW Info block */ +#define CFG_HWINFO_SIZE 0x00000060 /* size of HW Info block */ +#define CFG_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */ + +/*----------------------------------------------------------------------- + * NAND-FLASH stuff + *----------------------------------------------------------------------- + */ +#if (CONFIG_COMMANDS & CFG_CMD_NAND) + +#define CFG_NAND_CS_DIST 0x80 +#define CFG_NAND_UPM_WRITE_CMD_OFS 0x20 +#define CFG_NAND_UPM_WRITE_ADDR_OFS 0x40 + +#define CFG_NAND_BR ((CFG_NAND0_BASE & BRx_BA_MSK) |\ + BRx_PS_8 |\ + BRx_MS_UPMB |\ + BRx_V) + +#define CFG_NAND_OR (MEG_TO_AM(CFG_NAND_SIZE) |\ + ORxU_BI |\ + ORxU_EHTR_8IDLE) + +#define CFG_NAND_SIZE 1 +#define CFG_NAND0_BASE 0x50000000 +#define CFG_NAND1_BASE (CFG_NAND0_BASE + CFG_NAND_CS_DIST) +#define CFG_NAND2_BASE (CFG_NAND1_BASE + CFG_NAND_CS_DIST) +#define CFG_NAND3_BASE (CFG_NAND2_BASE + CFG_NAND_CS_DIST) + +#define CFG_MAX_NAND_DEVICE 4 /* Max number of NAND devices */ +#define NAND_MAX_CHIPS 1 + +#define CFG_NAND_BASE_LIST { CFG_NAND0_BASE, \ + CFG_NAND1_BASE, \ + CFG_NAND2_BASE, \ + CFG_NAND3_BASE, \ + } + +#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)(adr)) = (__u8)d; } while(0) +#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)(adr))) +#define WRITE_NAND_UPM(d, adr, off) do \ +{ \ + volatile unsigned char *addr = (unsigned char *) (adr + off); \ + WRITE_NAND(d, addr); \ +} while(0) + +#endif /* CFG_CMD_NAND */ + +#define CONFIG_PCI +#ifdef CONFIG_PCI +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ +#define CONFIG_PCI_PNP +#define CONFIG_EEPRO100 +#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ +#define CONFIG_PCI_SCAN_SHOW +#endif + +/*----------------------------------------------------------------------- + * Hard Reset Configuration Words + * + * if you change bits in the HRCW, you must also change the CFG_* + * defines for the various registers affected by the HRCW e.g. changing + * HRCW_DPPCxx requires you to also change CFG_SIUMCR. + */ +#if 0 +#define __HRCW__ALL__ (HRCW_CIP | HRCW_ISB111 | HRCW_BMS) + +# define CFG_HRCW_MASTER (__HRCW__ALL__ | HRCW_MODCK_H0111) +#else +#define CFG_HRCW_MASTER (HRCW_BPS11 | HRCW_ISB111 | HRCW_BMS | HRCW_MODCK_H0111) +#endif + +/* no slaves so just fill with zeros */ +#define CFG_HRCW_SLAVE1 0 +#define CFG_HRCW_SLAVE2 0 +#define CFG_HRCW_SLAVE3 0 +#define CFG_HRCW_SLAVE4 0 +#define CFG_HRCW_SLAVE5 0 +#define CFG_HRCW_SLAVE6 0 +#define CFG_HRCW_SLAVE7 0 + +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xFFF00000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x2000 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data*/ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE CFG_FLASH0_BASE +#define CFG_MONITOR_BASE TEXT_BASE +#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc()*/ + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH*/ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * HIDx - Hardware Implementation-dependent Registers 2-11 + *----------------------------------------------------------------------- + * HID0 also contains cache control - initially enable both caches and + * invalidate contents, then the final state leaves only the instruction + * cache enabled. Note that Power-On and Hard reset invalidate the caches, + * but Soft reset does not. + * + * HID1 has only read-only information - nothing to set. + */ +#define CFG_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|\ + HID0_IFEM|HID0_ABE) +#define CFG_HID0_FINAL (HID0_IFEM|HID0_ABE) +#define CFG_HID2 0 + +/*----------------------------------------------------------------------- + * RMR - Reset Mode Register 5-5 + *----------------------------------------------------------------------- + * turn on Checkstop Reset Enable + */ +#define CFG_RMR RMR_CSRE + +/*----------------------------------------------------------------------- + * BCR - Bus Configuration 4-25 + *----------------------------------------------------------------------- + */ +#define CFG_BCR_60x (BCR_EBM|BCR_NPQM0|BCR_NPQM2) /* 60x mode */ +#define BCR_APD01 0x10000000 +#define CFG_BCR_SINGLE (BCR_APD01|BCR_ETM) /* 8260 mode */ + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 4-31 + *----------------------------------------------------------------------- + */ +#if defined(CONFIG_BOARD_GET_CPU_CLK_F) +#define CFG_SIUMCR_LOW (SIUMCR_DPPC00) +#define CFG_SIUMCR_HIGH (SIUMCR_DPPC00 | SIUMCR_ABE) +#else +#define CFG_SIUMCR (SIUMCR_DPPC00) +#endif + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 4-35 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable + */ +#if defined(CONFIG_WATCHDOG) +#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ + SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE) +#else +#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ + SYPCR_SWRI|SYPCR_SWP) +#endif /* CONFIG_WATCHDOG */ + +/*----------------------------------------------------------------------- + * TMCNTSC - Time Counter Status and Control 4-40 + *----------------------------------------------------------------------- + * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk, + * and enable Time Counter + */ +#define CFG_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 4-42 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable + * Periodic timer + */ +#define CFG_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) + +/*----------------------------------------------------------------------- + * SCCR - System Clock Control 9-8 + *----------------------------------------------------------------------- + * Ensure DFBRG is Divide by 16 + */ +#define CFG_SCCR SCCR_DFBRG01 + +/*----------------------------------------------------------------------- + * RCCR - RISC Controller Configuration 13-7 + *----------------------------------------------------------------------- + */ +#define CFG_RCCR 0 + +/* + * Init Memory Controller: + * + * Bank Bus Machine PortSz Device + * ---- --- ------- ------ ------ + * 0 60x GPCM 32 bit FLASH + * 1 60x SDRAM 64 bit SDRAM + * 2 60x UPMB 8 bit NAND + * 3 60x UPMC 8 bit CAN + * + */ + +/* Initialize SDRAM + */ +#undef CFG_INIT_LOCAL_SDRAM /* No SDRAM on Local Bus */ + +#define SDRAM_MAX_SIZE 0x20000000 /* max. 512 MB */ + +/* Minimum mask to separate preliminary + * address ranges for CS[0:2] + */ +#define CFG_GLOBAL_SDRAM_LIMIT (512<<20) /* less than 512 MB */ + +#define CFG_MPTPR 0x4000 + +/*----------------------------------------------------------------------------- + * Address for Mode Register Set (MRS) command + *----------------------------------------------------------------------------- + * In fact, the address is rather configuration data presented to the SDRAM on + * its address lines. Because the address lines may be mux'ed externally either + * for 8 column or 9 column devices, some bits appear twice in the 8260's + * address: + * + * | (RFU) | (RFU) | WBL | TM | CL | BT | Burst Length | + * | BA1 BA0 | A12 : A10 | A9 | A8 A7 | A6 : A4 | A3 | A2 : A0 | + * 8 columns mux'ing: | A9 | A10 A21 | A22 : A24 | A25 | A26 : A28 | + * 9 columns mux'ing: | A8 | A20 A21 | A22 : A24 | A25 | A26 : A28 | + * Settings: | 0 | 0 0 | 0 1 0 | 0 | 0 1 0 | + *----------------------------------------------------------------------------- + */ +#define CFG_MRS_OFFS 0x00000110 + + +/* Bank 0 - FLASH + */ +#define CFG_BR0_PRELIM ((CFG_FLASH_BASE & BRx_BA_MSK) |\ + BRx_PS_32 |\ + BRx_MS_GPCM_P |\ + BRx_V) + +#define CFG_OR0_PRELIM (MEG_TO_AM(CFG_FLASH_SIZE) |\ + ORxG_CSNT |\ + ORxG_ACS_DIV4 |\ + ORxG_SCY_8_CLK |\ + ORxG_TRLX) + +/* SDRAM on TQM8272 can have either 8 or 9 columns. + * The number affects configuration values. + */ + +/* Bank 1 - 60x bus SDRAM + */ +#define CFG_PSRT 0x20 /* Low Value */ +/* #define CFG_PSRT 0x10 Fast Value */ +#define CFG_LSRT 0x20 /* Local Bus */ +#ifndef CFG_RAMBOOT +#define CFG_BR1_PRELIM ((CFG_SDRAM_BASE & BRx_BA_MSK) |\ + BRx_PS_64 |\ + BRx_MS_SDRAM_P |\ + BRx_V) + +#define CFG_OR1_PRELIM CFG_OR1_8COL + +/* SDRAM initialization values for 8-column chips + */ +#define CFG_OR1_8COL ((~(CFG_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\ + ORxS_BPD_4 |\ + ORxS_ROWST_PBI1_A7 |\ + ORxS_NUMR_12) + +#define CFG_PSDMR_8COL (PSDMR_PBI |\ + PSDMR_SDAM_A15_IS_A5 |\ + PSDMR_BSMA_A12_A14 |\ + PSDMR_SDA10_PBI1_A8 |\ + PSDMR_RFRC_7_CLK |\ + PSDMR_PRETOACT_2W |\ + PSDMR_ACTTORW_2W |\ + PSDMR_LDOTOPRE_1C |\ + PSDMR_WRC_2C |\ + PSDMR_EAMUX |\ + PSDMR_BUFCMD |\ + PSDMR_CL_2) + + +/* SDRAM initialization values for 9-column chips + */ +#define CFG_OR1_9COL ((~(CFG_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\ + ORxS_BPD_4 |\ + ORxS_ROWST_PBI1_A5 |\ + ORxS_NUMR_13) + +#define CFG_PSDMR_9COL (PSDMR_PBI |\ + PSDMR_SDAM_A16_IS_A5 |\ + PSDMR_BSMA_A12_A14 |\ + PSDMR_SDA10_PBI1_A7 |\ + PSDMR_RFRC_7_CLK |\ + PSDMR_PRETOACT_2W |\ + PSDMR_ACTTORW_2W |\ + PSDMR_LDOTOPRE_1C |\ + PSDMR_WRC_2C |\ + PSDMR_EAMUX |\ + PSDMR_BUFCMD |\ + PSDMR_CL_2) + +#define CFG_OR1_10COL ((~(CFG_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\ + ORxS_BPD_4 |\ + ORxS_ROWST_PBI1_A4 |\ + ORxS_NUMR_13) + +#define CFG_PSDMR_10COL (PSDMR_PBI |\ + PSDMR_SDAM_A17_IS_A5 |\ + PSDMR_BSMA_A12_A14 |\ + PSDMR_SDA10_PBI1_A4 |\ + PSDMR_RFRC_6_CLK |\ + PSDMR_PRETOACT_2W |\ + PSDMR_ACTTORW_2W |\ + PSDMR_LDOTOPRE_1C |\ + PSDMR_WRC_2C |\ + PSDMR_EAMUX |\ + PSDMR_BUFCMD |\ + PSDMR_CL_2) + + +#define PSDMR_RFRC_66MHZ_SINGLE 0x00028000 /* PSDMR[RFRC] at 66 MHz single mode */ +#define PSDMR_RFRC_100MHZ_SINGLE 0x00030000 /* PSDMR[RFRC] at 100 MHz single mode */ +#define PSDMR_RFRC_133MHZ_SINGLE 0x00030000 /* PSDMR[RFRC] at 133 MHz single mode */ +#define PSDMR_RFRC_66MHZ_60X 0x00030000 /* PSDMR[RFRC] at 66 MHz 60x mode */ +#define PSDMR_RFRC_100MHZ_60X 0x00028000 /* PSDMR[RFRC] at 100 MHz 60x mode */ +#define PSDMR_RFRC_DEFAULT PSDMR_RFRC_133MHZ_SINGLE /* PSDMR[RFRC] default value */ + +#define PSDMR_PRETOACT_66MHZ_SINGLE 0x00002000 /* PSDMR[PRETOACT] at 66 MHz single mode */ +#define PSDMR_PRETOACT_100MHZ_SINGLE 0x00002000 /* PSDMR[PRETOACT] at 100 MHz single mode */ +#define PSDMR_PRETOACT_133MHZ_SINGLE 0x00002000 /* PSDMR[PRETOACT] at 133 MHz single mode */ +#define PSDMR_PRETOACT_66MHZ_60X 0x00001000 /* PSDMR[PRETOACT] at 66 MHz 60x mode */ +#define PSDMR_PRETOACT_100MHZ_60X 0x00001000 /* PSDMR[PRETOACT] at 100 MHz 60x mode */ +#define PSDMR_PRETOACT_DEFAULT PSDMR_PRETOACT_133MHZ_SINGLE /* PSDMR[PRETOACT] default value */ + +#define PSDMR_WRC_66MHZ_SINGLE 0x00000020 /* PSDMR[WRC] at 66 MHz single mode */ +#define PSDMR_WRC_100MHZ_SINGLE 0x00000020 /* PSDMR[WRC] at 100 MHz single mode */ +#define PSDMR_WRC_133MHZ_SINGLE 0x00000010 /* PSDMR[WRC] at 133 MHz single mode */ +#define PSDMR_WRC_66MHZ_60X 0x00000010 /* PSDMR[WRC] at 66 MHz 60x mode */ +#define PSDMR_WRC_100MHZ_60X 0x00000010 /* PSDMR[WRC] at 100 MHz 60x mode */ +#define PSDMR_WRC_DEFAULT PSDMR_WRC_133MHZ_SINGLE /* PSDMR[WRC] default value */ + +#define PSDMR_BUFCMD_66MHZ_SINGLE 0x00000000 /* PSDMR[BUFCMD] at 66 MHz single mode */ +#define PSDMR_BUFCMD_100MHZ_SINGLE 0x00000000 /* PSDMR[BUFCMD] at 100 MHz single mode */ +#define PSDMR_BUFCMD_133MHZ_SINGLE 0x00000004 /* PSDMR[BUFCMD] at 133 MHz single mode */ +#define PSDMR_BUFCMD_66MHZ_60X 0x00000000 /* PSDMR[BUFCMD] at 66 MHz 60x mode */ +#define PSDMR_BUFCMD_100MHZ_60X 0x00000000 /* PSDMR[BUFCMD] at 100 MHz 60x mode */ +#define PSDMR_BUFCMD_DEFAULT PSDMR_BUFCMD_133MHZ_SINGLE /* PSDMR[BUFCMD] default value */ + +#endif /* CFG_RAMBOOT */ + +#endif /* __CONFIG_H */ diff --git a/include/mpc8260.h b/include/mpc8260.h index ff52a7b38b3..d9dd92d9a5e 100644 --- a/include/mpc8260.h +++ b/include/mpc8260.h @@ -35,7 +35,15 @@ #endif #ifndef CPU_ID_STR #if defined(CONFIG_MPC8272_FAMILY) +#ifdef CONFIG_MPC8247 +#define CPU_ID_STR "MPC8247" +#elif defined CONFIG_MPC8248 +#define CPU_ID_STR "MPC8248" +#elif defined CONFIG_MPC8271 +#define CPU_ID_STR "MPC8271" +#else #define CPU_ID_STR "MPC8272" +#endif #else #define CPU_ID_STR "MPC8260" #endif @@ -66,6 +74,7 @@ #define BCR_EXDD 0x00000400 /* External Master Delay Disable*/ #define BCR_ISPS 0x00000010 /* Internal Space Port Size */ + /*----------------------------------------------------------------------- * PPC_ACR - 60x Bus Arbiter Configuration Register 4-28 */ @@ -168,6 +177,7 @@ #define SIUMCR_MMR10 0x00008000 /* - " - */ #define SIUMCR_MMR11 0x0000c000 /* - " - */ #define SIUMCR_LPBSE 0x00002000 /* LocalBus Parity Byte Select Enable*/ +#define SIUMCR_ABE 0x00000400 /* Address output buffer impedance*/ /*----------------------------------------------------------------------- * IMMR - Internal Memory Map Register 4-34 diff --git a/lib_ppc/board.c b/lib_ppc/board.c index 844bbc90033..d9dead852dc 100644 --- a/lib_ppc/board.c +++ b/lib_ppc/board.c @@ -72,6 +72,10 @@ #include <keyboard.h> #endif +#ifdef CFG_UPDATE_FLASH_SIZE +extern int update_flash_size (int flash_size); +#endif + #if (CONFIG_COMMANDS & CFG_CMD_DOC) void doc_init (void); #endif @@ -730,6 +734,13 @@ void board_init_r (gd_t *id, ulong dest_addr) bd->bi_flashstart = CFG_FLASH_BASE; /* update start of FLASH memory */ bd->bi_flashsize = flash_size; /* size of FLASH memory (final value) */ + +#if defined(CFG_UPDATE_FLASH_SIZE) + /* Make a update of the Memctrl. */ + update_flash_size (flash_size); +#endif + + # if defined(CONFIG_PCU_E) || defined(CONFIG_OXC) || defined(CONFIG_RMU) /* flash mapped at end of memory map */ bd->bi_flashoffset = TEXT_BASE + flash_size; @@ -876,6 +887,7 @@ void board_init_r (gd_t *id, ulong dest_addr) #endif #if defined(CONFIG_TQM8xxL) || defined(CONFIG_TQM8260) || \ + defined(CONFIG_TQM8272) || \ defined(CONFIG_CCM) || defined(CONFIG_KUP4K) || defined(CONFIG_KUP4X) load_sernum_ethaddr (); #endif |