lib: optee: remove the duplicate CONFIG_OPTEE

The configuration CONFIG_OPTEE is defined 2 times:
1- in lib/optee/Kconfig for support of OPTEE images loaded by bootm command
2- in drivers/tee/optee/Kconfig for support of OP-TEE driver.

It is abnormal to have the same CONFIG define for 2 purpose;
and it is difficult to managed correctly their dependencies.

Moreover CONFIG_SPL_OPTEE is defined in common/spl/Kconfig
to manage OPTEE image load in SPL.

This definition causes an issue with the macro CONFIG_IS_ENABLED(OPTEE)
to test the availability of the OP-TEE driver.

This patch cleans the configuration dependency with:
- CONFIG_OPTEE_IMAGE (renamed) => support of OP-TEE image in U-Boot
- CONFIG_SPL_OPTEE_IMAGE (renamed) => support of OP-TEE image in SPL
- CONFIG_OPTEE (same) => support of OP-TEE driver in U-Boot
- CONFIG_OPTEE_LIB (new) => support of OP-TEE library

After this patch, the macro have the correct behavior:
- CONFIG_IS_ENABLED(OPTEE_IMAGE) => Load of OP-TEE image is supported
- CONFIG_IS_ENABLED(OPTEE) => OP-TEE driver is supported

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>

3 files changed, 17 insertions, 11 deletions

diff --git a/lib/optee/Kconfig b/lib/optee/Kconfig
index 3290b6656d..3072c28912 100644
--- a/lib/optee/Kconfig
+++ b/lib/optee/Kconfig
@@ -1,23 +1,27 @@
-config OPTEE
+config OPTEE_LIB
+	bool "Support OPTEE library"
+	default y if OPTEE || OPTEE_IMAGE
+	help
+	  Selecting this option will enable the shared OPTEE library code.
+
+config OPTEE_IMAGE
 	bool "Support OPTEE images"
 	help
-	  U-Boot can be configured to boot OPTEE images.
-	  Selecting this option will enable shared OPTEE library code and
-          enable an OPTEE specific bootm command that will perform additional
-          OPTEE specific checks before booting an OPTEE image created with
-          mkimage.
+	  Selecting this option to boot OPTEE images.
+	  This option enable the OPTEE specific checks done before booting
+	  an OPTEE image created with mkimage
 
 config OPTEE_LOAD_ADDR
 	hex "OPTEE load address"
 	default 0x00000000
-	depends on OPTEE
+	depends on OPTEE_LIB
 	help
 	  The load address of the bootable OPTEE binary.
 
 config OPTEE_TZDRAM_SIZE
 	hex "Amount of Trust-Zone RAM for the OPTEE image"
 	default 0x0000000
-	depends on OPTEE
+	depends on OPTEE_LIB
 	help
 	  The size of pre-allocated Trust Zone DRAM to allocate for the OPTEE
 	  runtime.
@@ -25,7 +29,7 @@ config OPTEE_TZDRAM_SIZE
 config OPTEE_TZDRAM_BASE
 	hex "Base address of Trust-Zone RAM for the OPTEE image"
 	default 0x00000000
-	depends on OPTEE
+	depends on OPTEE_LIB
 	help
 	  The base address of pre-allocated Trust Zone DRAM for
 	  the OPTEE runtime.
@@ -33,7 +37,7 @@ config OPTEE_TZDRAM_BASE
 config BOOTM_OPTEE
 	bool "Support OPTEE bootm command"
 	select BOOTM_LINUX
-	depends on OPTEE
+	select OPTEE_IMAGE
 	help
 	  Select this command to enable chain-loading of a Linux kernel
 	  via an OPTEE firmware.
diff --git a/lib/optee/Makefile b/lib/optee/Makefile
index b692311864..9befe606d8 100644
--- a/lib/optee/Makefile
+++ b/lib/optee/Makefile
@@ -2,4 +2,4 @@
 #
 # (C) Copyright 2017 Linaro
 
-obj-$(CONFIG_OPTEE) += optee.o
+obj-y += optee.o
diff --git a/lib/optee/optee.c b/lib/optee/optee.c
index 672690dc53..5676785cb5 100644
--- a/lib/optee/optee.c
+++ b/lib/optee/optee.c
@@ -20,6 +20,7 @@
 	"\n\theader lo=0x%08x hi=0x%08x size=0x%08lx arch=0x%08x" \
 	"\n\tuimage params 0x%08lx-0x%08lx\n"
 
+#if defined(CONFIG_OPTEE_IMAGE)
 int optee_verify_image(struct optee_header *hdr, unsigned long tzdram_start,
 		       unsigned long tzdram_len, unsigned long image_len)
 {
@@ -70,6 +71,7 @@ error:
 
 	return ret;
 }
+#endif
 
 #if defined(CONFIG_OF_LIBFDT)
 static int optee_copy_firmware_node(ofnode node, void *fdt_blob)