powerpc: mpc85xx: remove stxgp3, stxssa support

These have not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Dan Malek <dan@embeddedalley.com>

2 files changed, 0 insertions, 794 deletions

diff --git a/include/configs/stxgp3.h b/include/configs/stxgp3.h
deleted file mode 100644
index 25b7d5f6a6..0000000000
--- a/include/configs/stxgp3.h
+++ /dev/null
@@ -1,354 +0,0 @@
-/*
- * (C) Copyright 2003 Embedded Edge, LLC
- * Dan Malek <dan@embeddededge.com>
- * Copied from ADS85xx.
- * Updates for Silicon Tx GP3 8560 board.
- *
- * (C) Copyright 2002,2003 Motorola,Inc.
- * Xianghua Xiao <X.Xiao@motorola.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/* mpc8560ads board configuration file */
-/* please refer to doc/README.mpc85xx for more info */
-/* make sure you change the MAC address and other network params first,
- * search for CONFIG_SERVERIP, etc. in this file
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/* High Level Configuration Options */
-#define CONFIG_BOOKE		1	/* BOOKE		*/
-#define CONFIG_E500		1	/* BOOKE e500 family	*/
-#define CONFIG_CPM2		1	/* has CPM2 */
-#define CONFIG_STXGP3		1	/* Silicon Tx GPPP board specific*/
-#define CONFIG_MPC8560		1
-
-#define	CONFIG_SYS_TEXT_BASE	0xfff80000
-
-#undef  CONFIG_PCI			/* pci ethernet support	*/
-#define CONFIG_TSEC_ENET		/* tsec ethernet support*/
-#undef  CONFIG_ETHER_ON_FCC             /* cpm FCC ethernet support */
-#define CONFIG_ENV_OVERWRITE
-
-#define CONFIG_FSL_LAW		1	/* Use common FSL init code */
-
-/* sysclk for MPC85xx
- */
-
-#define CONFIG_SYS_CLK_FREQ     33333333 /* most pci cards are 33Mhz */
-
-/* Blinkin' LEDs for Robert :-)
-*/
-#define CONFIG_SHOW_ACTIVITY 1
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_L2_CACHE                     /* toggle L2 cache         */
-#define  CONFIG_BTB                          /* toggle branch predition */
-
-#define CONFIG_BOARD_EARLY_INIT_F   1        /* Call board_pre_init      */
-#define CONFIG_RESET_PHY_R	1	/* Call reset_phy()		*/
-
-#undef  CONFIG_SYS_DRAM_TEST                       /* memory test, takes time  */
-#define CONFIG_SYS_MEMTEST_START       0x00200000  /* memtest region */
-#define CONFIG_SYS_MEMTEST_END         0x00400000
-
-
-/* Localbus SDRAM is an option, not all boards have it.
- * This address, however, is used to configure a 256M local bus
- * window that includes the Config latch below.
- */
-#define CONFIG_SYS_LBC_SDRAM_BASE      0xf0000000      /* Localbus SDRAM */
-#define CONFIG_SYS_LBC_SDRAM_SIZE	256		/* LBC SDRAM is 64MB	*/
-
-#define CONFIG_SYS_FLASH_BASE        0xff000000      /* start of FLASH 16M    */
-#define CONFIG_SYS_BR0_PRELIM        0xff001801      /* port size 32bit      */
-
-#define CONFIG_SYS_OR0_PRELIM          0xff000ff7      /* 16 MB Flash           */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1		/* number of banks	*/
-#define CONFIG_SYS_MAX_FLASH_SECT	136		/* sectors per device   */
-#undef	CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-/* The configuration latch is Chip Select 1.
- * It's an 8-bit latch in the lower 8 bits of the word.
- */
-#define CONFIG_SYS_BR1_PRELIM		0xfc001801	/* 32-bit port */
-#define CONFIG_SYS_OR1_PRELIM		0xffff0ff7      /* 64K is enough */
-#define CONFIG_SYS_LBC_LCLDEVS_BASE	0xfc000000	/* Base of localbus devices */
-
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor	*/
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#else
-#undef  CONFIG_SYS_RAMBOOT
-#endif
-
-#ifdef CONFIG_SYS_RAMBOOT
-#define CONFIG_SYS_CCSRBAR_DEFAULT	0x40000000	/* CCSRBAR by BDI cfg	*/
-#endif
-#define CONFIG_SYS_CCSRBAR		0xfdf00000
-#define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
-
-/* DDR Setup */
-#define CONFIG_SYS_FSL_DDR1
-#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
-#define CONFIG_DDR_SPD
-#undef CONFIG_FSL_DDR_INTERACTIVE
-
-#undef  CONFIG_DDR_ECC			/* only for ECC DDR module */
-#define CONFIG_SYS_FSL_ERRATUM_DDR_MSYNC_IN	/* possible DLL fix needed */
-#define CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
-
-#define CONFIG_MEM_INIT_VALUE		0xDeadBeef
-
-#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
-#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
-
-#define CONFIG_NUM_DDR_CONTROLLERS	1
-#define CONFIG_DIMM_SLOTS_PER_CTLR	1
-#define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)
-
-/* I2C addresses of SPD EEPROMs */
-#define SPD_EEPROM_ADDRESS	0x54	/* CTLR 0 DIMM 0 */
-
-#undef CONFIG_CLOCKS_IN_MHZ
-
-/* local bus definitions */
-#define CONFIG_SYS_BR2_PRELIM		0xf8001861	/* 64MB localbus SDRAM  */
-#define CONFIG_SYS_OR2_PRELIM		0xfc006901
-#define CONFIG_SYS_LBC_LCRR		0x00030004	/* local bus freq	*/
-#define CONFIG_SYS_LBC_LBCR		0x00000000
-#define CONFIG_SYS_LBC_LSRT		0x20000000
-#define CONFIG_SYS_LBC_MRTPR		0x20000000
-#define CONFIG_SYS_LBC_LSDMR_1		0x2861b723
-#define CONFIG_SYS_LBC_LSDMR_2		0x0861b723
-#define CONFIG_SYS_LBC_LSDMR_3		0x0861b723
-#define CONFIG_SYS_LBC_LSDMR_4		0x1861b723
-#define CONFIG_SYS_LBC_LSDMR_5		0x4061b723
-
-#define CONFIG_SYS_INIT_RAM_LOCK	1
-#define CONFIG_SYS_INIT_RAM_ADDR       0x60000000      /* Initial RAM address  */
-#define CONFIG_SYS_INIT_RAM_SIZE	0x4000		/* Size of used area in RAM */
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN		(256 * 1024)    /* Reserve 256 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN		(128 * 1024)    /* Reserved for malloc */
-
-/* Serial Port */
-#define CONFIG_CONS_ON_SCC		/* define if console on SCC */
-#undef  CONFIG_CONS_NONE		/* define if console on something else */
-#define CONFIG_CONS_INDEX       2	/* which serial channel for console */
-
-#define CONFIG_BAUDRATE		38400
-
-#define CONFIG_SYS_BAUDRATE_TABLE  \
-	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
-
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-#ifdef  CONFIG_SYS_HUSH_PARSER
-#endif
-
-/*
- * I2C
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED	400000
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
-
-#if 0
-#define CONFIG_SYS_I2C_NOPROBES        {0x00}  /* Don't probe these addrs */
-#else
-/* I did the 'if 0' so we could keep the syntax above if ever needed. */
-#undef CONFIG_SYS_I2C_NOPROBES
-#endif
-
-/* RapdIO Map configuration, mapped 1:1.
-*/
-#define CONFIG_SYS_RIO_MEM_BASE	0xc0000000
-#define CONFIG_SYS_RIO_MEM_PHYS	CONFIG_SYS_RIO_MEM_BASE
-#define CONFIG_SYS_RIO_MEM_SIZE	0x200000000	/* 512 M */
-
-/* Standard 8560 PCI addressing, mapped 1:1.
-*/
-#define CONFIG_SYS_PCI1_MEM_BASE	0x80000000
-#define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BASE
-#define CONFIG_SYS_PCI1_MEM_SIZE	0x20000000	/* 512M */
-#define CONFIG_SYS_PCI1_IO_BASE	0xe2000000
-#define CONFIG_SYS_PCI1_IO_PHYS	CONFIG_SYS_PCI1_IO_BASE
-#define CONFIG_SYS_PCI1_IO_SIZE	0x01000000	/* 16 M */
-
-#if defined(CONFIG_PCI)			/* PCI Ethernet card */
-
-#define CONFIG_PCI_PNP			/* do pci plug-and-play */
-
-#undef CONFIG_EEPRO100
-#undef CONFIG_TULIP
-
-#if !defined(CONFIG_PCI_PNP)
-  #define PCI_ENET0_IOADDR	0xe0000000
-  #define PCI_ENET0_MEMADDR     0xe0000000
-  #define PCI_IDSEL_NUMBER      0x0c	/* slot0->3(IDSEL)=12->15 */
-#endif
-
-#undef CONFIG_PCI_SCAN_SHOW
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057  /* Motorola */
-
-#endif /* CONFIG_PCI */
-
-#if defined(CONFIG_TSEC_ENET)
-
-#define CONFIG_MII		1	/* MII PHY management		*/
-
-#define CONFIG_TSEC1	1
-#define CONFIG_TSEC1_NAME	"TSEC0"
-#define CONFIG_TSEC2	1
-#define CONFIG_TSEC2_NAME	"TSEC1"
-
-#define TSEC1_PHY_ADDR		2
-#define TSEC2_PHY_ADDR		4
-#define TSEC1_PHYIDX		0
-#define TSEC2_PHYIDX		0
-#define TSEC1_FLAGS		TSEC_GIGABIT
-#define TSEC2_FLAGS		TSEC_GIGABIT
-#define CONFIG_ETHPRIME		"TSEC0"
-
-#elif defined(CONFIG_ETHER_ON_FCC)	/* CPM FCC Ethernet */
-
-#define CONFIG_ETHER_ON_FCC2             /* define if ether on FCC   */
-#undef  CONFIG_ETHER_NONE               /* define if ether on something else */
-#define CONFIG_ETHER_INDEX      2       /* which channel for ether  */
-
-#if (CONFIG_ETHER_INDEX == 2)
-  /*
-   * - Rx-CLK is CLK13
-   * - Tx-CLK is CLK14
-   * - Select bus for bd/buffers
-   * - Full duplex
-   */
-  #define CONFIG_SYS_CMXFCR_MASK2      (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
-  #define CONFIG_SYS_CMXFCR_VALUE2     (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
-  #define CONFIG_SYS_CPMFCR_RAMTYPE    0
-#if 0
-  #define CONFIG_SYS_FCC_PSMR          (FCC_PSMR_FDE)
-#else
-  #define CONFIG_SYS_FCC_PSMR          0
-#endif
-  #define FETH2_RST		0x01
-#elif (CONFIG_ETHER_INDEX == 3)
-  /* need more definitions here for FE3 */
-  #define FETH3_RST		0x80
-#endif	/* CONFIG_ETHER_INDEX */
-
-/* MDIO is done through the TSEC0 control.
-*/
-#define CONFIG_MII			/* MII PHY management */
-#undef CONFIG_BITBANGMII		/* bit-bang MII PHY management	*/
-
-#endif
-
-/* Environment */
-/* We use the top boot sector flash, so we have some 16K sectors for env
- */
-#ifndef CONFIG_SYS_RAMBOOT
-  #define CONFIG_ENV_IS_IN_FLASH	1
-  #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + 0x60000)
-  #define CONFIG_ENV_SECT_SIZE	0x4000	/* 16K (one top sector) for env */
-  #define CONFIG_ENV_SIZE		0x2000
-#else
-  #define CONFIG_SYS_NO_FLASH		1	/* Flash is not usable now	*/
-  #define CONFIG_ENV_IS_NOWHERE	1	/* Store ENV in memory only	*/
-  #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
-  #define CONFIG_ENV_SIZE		0x2000
-#endif
-
-#define CONFIG_BOOTARGS "root=/dev/nfs rw ip=any console=ttyS1,38400"
-#define CONFIG_BOOTCOMMAND	"bootm 0xff000000 0xff100000"
-#define CONFIG_BOOTDELAY	3	/* -1 disable autoboot */
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_REGINFO
-
-#if !defined(CONFIG_SYS_RAMBOOT)
-    #define CONFIG_CMD_ELF
-#endif
-
-#if defined(CONFIG_PCI)
-    #define CONFIG_CMD_PCI
-#endif
-
-#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
-    #define CONFIG_CMD_MII
-#endif
-
-
-#undef CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-#define CONFIG_SYS_LOAD_ADDR	0x1000000	/* default load address */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20) /* Initial Memory map for Linux */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#endif
-
-#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#define CONFIG_HAS_ETH2
-#endif
-
-#define CONFIG_SERVERIP		192.168.85.1
-#define CONFIG_IPADDR		192.168.85.60
-#define CONFIG_GATEWAYIP	192.168.85.1
-#define CONFIG_NETMASK		255.255.255.0
-#define CONFIG_HOSTNAME		STX_GP3
-#define CONFIG_ROOTPATH		"/gppproot"
-#define CONFIG_BOOTFILE		"uImage"
-#define CONFIG_LOADADDR		0x1000000
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/stxssa.h b/include/configs/stxssa.h
deleted file mode 100644
index ee16fea3ae..0000000000
--- a/include/configs/stxssa.h
+++ /dev/null
@@ -1,440 +0,0 @@
-/*
- * (C) Copyright 2005 Embedded Alley Solutions, Inc.
- * Dan Malek <dan@embeddedalley.com>
- * Copied from STx GP3.
- * Updates for Silicon Tx GP3 SSA board.
- *
- * (C) Copyright 2002,2003 Motorola,Inc.
- * Xianghua Xiao <X.Xiao@motorola.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/* mpc8560ads board configuration file */
-/* please refer to doc/README.mpc85xx for more info */
-/* make sure you change the MAC address and other network params first,
- * search for CONFIG_SERVERIP, etc. in this file
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/* High Level Configuration Options */
-#define CONFIG_BOOKE		1	/* BOOKE		*/
-#define CONFIG_E500		1	/* BOOKE e500 family	*/
-#define CONFIG_CPM2		1	/* has CPM2 */
-#define CONFIG_STXSSA		1	/* Silicon Tx GPPP SSA board specific*/
-#define CONFIG_MPC8560		1
-
-#define	CONFIG_SYS_TEXT_BASE	0xFFF80000
-
-#define CONFIG_PCI			/* PCI ethernet support	*/
-#define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
-#define CONFIG_TSEC_ENET		/* tsec ethernet support*/
-#undef CONFIG_ETHER_ON_FCC		/* cpm FCC ethernet support */
-#define CONFIG_ENV_OVERWRITE
-
-#define CONFIG_FSL_LAW		1	/* Use common FSL init code */
-
-/* sysclk for MPC85xx
- */
-
-#define CONFIG_SYS_CLK_FREQ	33000000 /* most pci cards are 33Mhz */
-
-/* Blinkin' LEDs for Robert :-)
-*/
-#define CONFIG_SHOW_ACTIVITY 1
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_L2_CACHE				/* toggle L2 cache	       */
-#define  CONFIG_BTB				/* toggle branch predition */
-
-#define CONFIG_BOARD_EARLY_INIT_F   1		/* Call board_pre_init	 */
-
-#undef	CONFIG_SYS_DRAM_TEST				/* memory test, takes time	*/
-#define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest region */
-#define CONFIG_SYS_MEMTEST_END		0x00400000
-
-
-/* Localbus connector.	There are many options that can be
- * connected here, including sdram or lots of flash.
- * This address, however, is used to configure a 256M local bus
- * window that includes the Config latch below.
- */
-#define CONFIG_SYS_LBC_OPTION_BASE	0xF0000000	/* Localbus Extension */
-#define CONFIG_SYS_LBC_OPTION_SIZE	256		/* 256MB */
-
-/* There are various flash options used, we configure for the largest,
- * which is 64Mbytes.  The CFI works fine and will discover the proper
- * sizes.
- */
-#ifdef CONFIG_STXSSA_4M
-#define CONFIG_SYS_FLASH_BASE		0xFFC00000	/* start of  4 MiB flash */
-#else
-#define CONFIG_SYS_FLASH_BASE		0xFC000000	/* start of 64 MiB flash */
-#endif
-#define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE | 0x1801) /* port size 32bit	 */
-#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_FLASH_BASE | 0x0FF7)
-
-#define CONFIG_SYS_FLASH_CFI		1
-#define CONFIG_FLASH_CFI_DRIVER	1
-#undef CONFIG_SYS_FLASH_USE_BUFFER_WRITE	/* use buffered writes (20x faster) */
-#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max number of sectors on one chip */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks	*/
-
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-
-#define CONFIG_SYS_FLASH_PROTECTION
-
-/* The configuration latch is Chip Select 1.
- * It's an 8-bit latch in the lower 8 bits of the word.
- */
-#define CONFIG_SYS_LBC_CFGLATCH_BASE	0xFB000000	/* Base of config latch */
-#define CONFIG_SYS_BR1_PRELIM		0xFB001801	/* 32-bit port */
-#define CONFIG_SYS_OR1_PRELIM		0xFFFF0FF7	/* 64K is enough */
-
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor	*/
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#else
-#undef	CONFIG_SYS_RAMBOOT
-#endif
-
-#ifdef CONFIG_SYS_RAMBOOT
-#define CONFIG_SYS_CCSRBAR_DEFAULT	0x40000000	/* CCSRBAR by BDI cfg	*/
-#endif
-
-#define CONFIG_SYS_CCSRBAR		0xe0000000
-#define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
-
-/* DDR Setup */
-#define CONFIG_SYS_FSL_DDR1
-#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
-#define CONFIG_DDR_SPD
-#undef CONFIG_FSL_DDR_INTERACTIVE
-
-#undef	CONFIG_DDR_ECC			/* only for ECC DDR module */
-#define CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
-
-#define CONFIG_MEM_INIT_VALUE		0xDeadBeef
-
-#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
-#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
-
-#define CONFIG_NUM_DDR_CONTROLLERS	1
-#define CONFIG_DIMM_SLOTS_PER_CTLR	1
-#define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)
-
-/* I2C addresses of SPD EEPROMs */
-#define SPD_EEPROM_ADDRESS	0x54	/* CTLR 0 DIMM 0 */
-
-#undef CONFIG_CLOCKS_IN_MHZ
-
-/* local bus definitions */
-#define CONFIG_SYS_BR2_PRELIM		0xf8001861	/* 64MB localbus SDRAM	*/
-#define CONFIG_SYS_OR2_PRELIM		0xfc006901
-#define CONFIG_SYS_LBC_LCRR		0x00030004	/* local bus freq	*/
-#define CONFIG_SYS_LBC_LBCR		0x00000000
-#define CONFIG_SYS_LBC_LSRT		0x20000000
-#define CONFIG_SYS_LBC_MRTPR		0x20000000
-#define CONFIG_SYS_LBC_LSDMR_1		0x2861b723
-#define CONFIG_SYS_LBC_LSDMR_2		0x0861b723
-#define CONFIG_SYS_LBC_LSDMR_3		0x0861b723
-#define CONFIG_SYS_LBC_LSDMR_4		0x1861b723
-#define CONFIG_SYS_LBC_LSDMR_5		0x4061b723
-
-#define CONFIG_SYS_INIT_RAM_LOCK	1
-#define CONFIG_SYS_INIT_RAM_ADDR	0x60000000	/* Initial RAM address	*/
-#define CONFIG_SYS_INIT_RAM_SIZE	0x4000		/* Size of used area in RAM */
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN		(512 * 1024)	/* Reserved for malloc */
-
-/* Serial Port */
-#define CONFIG_CONS_INDEX     2
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE  \
-	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
-
-#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
-#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_AUTO_COMPLETE	1	/* add autocompletion support   */
-#define CONFIG_SYS_HUSH_PARSER		1	/* Use the HUSH parser		*/
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT		1
-#define CONFIG_OF_BOARD_SETUP		1
-#define CONFIG_OF_STDOUT_VIA_ALIAS	1
-
-/*
- * I2C
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED	400000
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
-#undef CONFIG_SYS_I2C_NOPROBES
-
-/* I2C RTC */
-#define CONFIG_RTC_DS1337		/* This is really a DS1339 RTC	*/
-#define CONFIG_SYS_I2C_RTC_ADDR	0x68	/* at address 0x68		*/
-
-/* I2C EEPROM.	AT24C32, we keep our environment in here.
-*/
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x51	/* 1010001x		*/
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	5	/* =32 Bytes per write	*/
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	20
-
-/*
- * Standard 8555 PCI mapping.
- * Addresses are mapped 1-1.
- */
-#define CONFIG_SYS_PCI1_MEM_BASE	0x80000000
-#define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BASE
-#define CONFIG_SYS_PCI1_MEM_SIZE	0x20000000	/* 512M */
-#define CONFIG_SYS_PCI1_IO_BASE	0x00000000
-#define CONFIG_SYS_PCI1_IO_PHYS	0xe2000000
-#define CONFIG_SYS_PCI1_IO_SIZE	0x01000000	/* 16M */
-
-#define CONFIG_SYS_PCI2_MEM_BASE	0xa0000000
-#define CONFIG_SYS_PCI2_MEM_PHYS	CONFIG_SYS_PCI2_MEM_BASE
-#define CONFIG_SYS_PCI2_MEM_SIZE	0x20000000	/* 512M */
-#define CONFIG_SYS_PCI2_IO_BASE	0x00000000
-#define CONFIG_SYS_PCI2_IO_PHYS	0xe3000000
-#define CONFIG_SYS_PCI2_IO_SIZE	0x01000000	/* 16M */
-
-#if defined(CONFIG_PCI)			/* PCI Ethernet card */
-#define CONFIG_MPC85XX_PCI2	1
-#define CONFIG_PCI_PNP			/* do pci plug-and-play */
-
-#define CONFIG_EEPRO100
-#define CONFIG_TULIP
-
-#if !defined(CONFIG_PCI_PNP)
-  #define PCI_ENET0_IOADDR	0xe0000000
-  #define PCI_ENET0_MEMADDR	0xe0000000
-  #define PCI_IDSEL_NUMBER	0x0c	/* slot0->3(IDSEL)=12->15 */
-#endif
-
-#define CONFIG_PCI_SCAN_SHOW
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057	/* Motorola */
-
-#endif /* CONFIG_PCI */
-
-#if defined(CONFIG_TSEC_ENET)
-
-#define CONFIG_MII		1	/* MII PHY management		*/
-
-#define CONFIG_TSEC1	1
-#define CONFIG_TSEC1_NAME	"TSEC0"
-#define CONFIG_TSEC2	1
-#define CONFIG_TSEC2_NAME	"TSEC1"
-
-#define TSEC1_PHY_ADDR		2
-#define TSEC2_PHY_ADDR		4
-#define TSEC1_PHYIDX		0
-#define TSEC2_PHYIDX		0
-#define TSEC1_FLAGS		TSEC_GIGABIT
-#define TSEC2_FLAGS		TSEC_GIGABIT
-#define CONFIG_ETHPRIME		"TSEC0"
-
-#elif defined(CONFIG_ETHER_ON_FCC)	/* CPM FCC Ethernet */
-
-#define CONFIG_ETHER_ON_FCC2		/* define if ether on FCC   */
-#undef	CONFIG_ETHER_NONE		/* define if ether on something else */
-#define CONFIG_ETHER_INDEX	2	/* which channel for ether  */
-
-#if (CONFIG_ETHER_INDEX == 2)
-  /*
-   * - Rx-CLK is CLK13
-   * - Tx-CLK is CLK14
-   * - Select bus for bd/buffers
-   * - Full duplex
-   */
-  #define CONFIG_SYS_CMXFCR_MASK2	(CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
-  #define CONFIG_SYS_CMXFCR_VALUE2	(CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
-  #define CONFIG_SYS_CPMFCR_RAMTYPE	0
-#if 0
-  #define CONFIG_SYS_FCC_PSMR		(FCC_PSMR_FDE)
-#else
-  #define CONFIG_SYS_FCC_PSMR		0
-#endif
-  #define FETH2_RST		0x01
-#elif (CONFIG_ETHER_INDEX == 3)
-  /* need more definitions here for FE3 */
-  #define FETH3_RST		0x80
-#endif					/* CONFIG_ETHER_INDEX */
-
-/* MDIO is done through the TSEC0 control.
-*/
-#define CONFIG_MII			/* MII PHY management */
-#undef CONFIG_BITBANGMII		/* bit-bang MII PHY management	*/
-
-#endif
-
-/* Environment - default config is in flash, see below */
-#if 0	/* in EEPROM */
-# define CONFIG_ENV_IS_IN_EEPROM	1
-# define CONFIG_ENV_OFFSET		0
-# define CONFIG_ENV_SIZE		2048
-#else	/* in flash */
-# define CONFIG_ENV_IS_IN_FLASH	1
-# ifdef CONFIG_STXSSA_4M
-#  define CONFIG_ENV_SECT_SIZE	0x20000
-# else	/* default configuration - 64 MiB flash */
-#  define CONFIG_ENV_SECT_SIZE	0x40000
-# endif
-# define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
-# define CONFIG_ENV_SIZE		0x4000
-# define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE)
-# define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-#endif
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
-
-#define	CONFIG_TIMESTAMP		/* Print image info with ts	*/
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SNTP
-#define CONFIG_CMD_REGINFO
-
-#if defined(CONFIG_PCI)
-    #define CONFIG_CMD_PCI
-#endif
-
-#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
-    #define CONFIG_CMD_MII
-#endif
-
-#if !defined(CONFIG_SYS_RAMBOOT)
-    #define CONFIG_CMD_ELF
-#endif
-
-
-#undef CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-#define CONFIG_SYS_LOAD_ADDR	0x1000000	/* default load address */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20) /* Initial Memory map for Linux */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#endif
-
-#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#define CONFIG_HAS_ETH2
-#endif
-
-/*
- * Environment in EEPROM is compatible with different flash sector sizes,
- * but only little space is available, so we use a very simple setup.
- * With environment in flash, we use a more powerful default configuration.
- */
-#ifdef CONFIG_ENV_IS_IN_EEPROM		/* use restricted "standard" environment */
-
-#define CONFIG_BAUDRATE		38400
-
-#define CONFIG_BOOTDELAY	3	/* -1 disable autoboot */
-#define CONFIG_BOOTCOMMAND	"bootm 0xffc00000 0xffd00000"
-#define CONFIG_BOOTARGS		"root=/dev/nfs rw ip=any console=ttyS1,$baudrate"
-#define CONFIG_SERVERIP		192.168.85.1
-#define CONFIG_IPADDR		192.168.85.60
-#define CONFIG_GATEWAYIP	192.168.85.1
-#define CONFIG_NETMASK		255.255.255.0
-#define CONFIG_HOSTNAME		STX_SSA
-#define CONFIG_ROOTPATH		"/gppproot"
-#define CONFIG_BOOTFILE		"uImage"
-#define CONFIG_LOADADDR		0x1000000
-
-#else /* ENV IS IN FLASH		-- use a full-blown envionment */
-
-#define CONFIG_BAUDRATE		115200
-
-#define CONFIG_BOOTDELAY	5	/* -1 disable autoboot */
-
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS		/* the boot command will set bootargs	*/
-
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"hostname=gp3ssa\0"						\
-	"bootfile=/tftpboot/gp3ssa/uImage\0"				\
-	"loadaddr=400000\0"						\
-	"netdev=eth0\0"							\
-	"consdev=ttyS1\0"						\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=$serverip:$rootpath\0"				\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs $bootargs "				\
-		"ip=$ipaddr:$serverip:$gatewayip:$netmask"		\
-		":$hostname:$netdev:off panic=1\0"			\
-	"addcons=setenv bootargs $bootargs "				\
-		"console=$consdev,$baudrate\0"				\
-	"flash_nfs=run nfsargs addip addcons;"				\
-		"bootm $kernel_addr\0"					\
-	"flash_self=run ramargs addip addcons;"				\
-		"bootm $kernel_addr $ramdisk_addr\0"			\
-	"net_nfs=tftp $loadaddr $bootfile;"				\
-		"run nfsargs addip addcons;bootm\0"			\
-	"rootpath=/opt/eldk/ppc_85xx\0"					\
-	"kernel_addr=FC000000\0"					\
-	"ramdisk_addr=FC200000\0"					\
-	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#endif	/* CONFIG_ENV_IS_IN_EEPROM */
-
-#endif	/* __CONFIG_H */