Merge git://git.denx.de/u-boot-mpc83xx

- Update MPC83xx platform support to current best practices, etc.

46 files changed, 2043 insertions, 4873 deletions

diff --git a/include/configs/MPC8308RDB.h b/include/configs/MPC8308RDB.h
index 3827ea464b..85d7ff6c52 100644
--- a/include/configs/MPC8308RDB.h
+++ b/include/configs/MPC8308RDB.h
@@ -12,8 +12,6 @@
  * High Level Configuration Options
  */
 #define CONFIG_E300		1 /* E300 family */
-#define CONFIG_MPC830x		1 /* MPC830x family */
-#define CONFIG_MPC8308		1 /* MPC8308 CPU specific */
 
 #ifdef CONFIG_MMC
 #define CONFIG_SYS_FSL_ESDHC_ADDR	CONFIG_SYS_MPC83xx_ESDHC_ADDR
@@ -30,92 +28,15 @@
 #define CONFIG_VSC7385_ENET
 
 /*
- * System Clock Setup
- */
-#define CONFIG_83XX_CLKIN	33333333 /* in Hz */
-#define CONFIG_SYS_CLK_FREQ	CONFIG_83XX_CLKIN
-
-/*
- * Hardware Reset Configuration Word
- * if CLKIN is 66.66MHz, then
- * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz
- * We choose the A type silicon as default, so the core is 400Mhz.
- */
-#define CONFIG_SYS_HRCW_LOW (\
-	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
-	HRCWL_DDR_TO_SCB_CLK_2X1 |\
-	HRCWL_SVCOD_DIV_2 |\
-	HRCWL_CSB_TO_CLKIN_4X1 |\
-	HRCWL_CORE_TO_CSB_3X1)
-/*
- * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits
- * in 8308's HRCWH according to the manual, but original Freescale's
- * code has them and I've expirienced some problems using the board
- * with BDI3000 attached when I've tried to set these bits to zero
- * (UART doesn't work after the 'reset run' command).
- */
-#define CONFIG_SYS_HRCW_HIGH (\
-	HRCWH_PCI_HOST |\
-	HRCWH_PCI1_ARBITER_ENABLE |\
-	HRCWH_CORE_ENABLE |\
-	HRCWH_FROM_0X00000100 |\
-	HRCWH_BOOTSEQ_DISABLE |\
-	HRCWH_SW_WATCHDOG_DISABLE |\
-	HRCWH_ROM_LOC_LOCAL_16BIT |\
-	HRCWH_RL_EXT_LEGACY |\
-	HRCWH_TSEC1M_IN_RGMII |\
-	HRCWH_TSEC2M_IN_RGMII |\
-	HRCWH_BIG_ENDIAN)
-
-/*
- * System IO Config
- */
-#define CONFIG_SYS_SICRH (\
-	SICRH_ESDHC_A_SD |\
-	SICRH_ESDHC_B_SD |\
-	SICRH_ESDHC_C_SD |\
-	SICRH_GPIO_A_TSEC2 |\
-	SICRH_GPIO_B_TSEC2_GTX_CLK125 |\
-	SICRH_IEEE1588_A_GPIO |\
-	SICRH_USB |\
-	SICRH_GTM_GPIO |\
-	SICRH_IEEE1588_B_GPIO |\
-	SICRH_ETSEC2_CRS |\
-	SICRH_GPIOSEL_1 |\
-	SICRH_TMROBI_V3P3 |\
-	SICRH_TSOBI1_V2P5 |\
-	SICRH_TSOBI2_V2P5)	/* 0x01b7d103 */
-#define CONFIG_SYS_SICRL (\
-	SICRL_SPI_PF0 |\
-	SICRL_UART_PF0 |\
-	SICRL_IRQ_PF0 |\
-	SICRL_I2C2_PF0 |\
-	SICRL_ETSEC1_GTX_CLK125)	/* 0x00000040 */
-
-/*
- * IMMR new address
- */
-#define CONFIG_SYS_IMMR		0xE0000000
-
-/*
  * SERDES
  */
 #define CONFIG_FSL_SERDES
 #define CONFIG_FSL_SERDES1	0xe3000
 
 /*
- * Arbiter Setup
- */
-#define CONFIG_SYS_ACR_PIPE_DEP	3 /* Arbiter pipeline depth is 4 */
-#define CONFIG_SYS_ACR_RPTCNT	3 /* Arbiter repeat count is 4 */
-#define CONFIG_SYS_SPCR_TSECEP	3 /* eTSEC emergency priority is highest */
-
-/*
  * DDR Setup
  */
-#define CONFIG_SYS_DDR_BASE		0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_SDRAM_BASE		0x00000000 /* DDR is system memory */
 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
 #define CONFIG_SYS_DDRCDR_VALUE	(DDRCDR_EN \
 				| DDRCDR_PZ_LOZ \
@@ -201,13 +122,6 @@
 	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 
 /*
- * Local Bus Configuration & Clock Setup
- */
-#define CONFIG_SYS_LCRR_DBYP		LCRR_DBYP
-#define CONFIG_SYS_LCRR_CLKDIV		LCRR_CLKDIV_2
-#define CONFIG_SYS_LBC_LBCR		0x00040000
-
-/*
  * FLASH on the Local Bus
  */
 #define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
@@ -215,22 +129,6 @@
 #define CONFIG_SYS_FLASH_BASE		0xFE000000 /* FLASH base address */
 #define CONFIG_SYS_FLASH_SIZE		8 /* FLASH size is 8M */
 
-/* Window base at flash base */
-#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_8MB)
-
-#define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE \
-				| BR_PS_16	/* 16 bit port */ \
-				| BR_MS_GPCM	/* MSEL = GPCM */ \
-				| BR_V)		/* valid */
-#define CONFIG_SYS_OR0_PRELIM	(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
-				| OR_UPM_XAM \
-				| OR_GPCM_CSNT \
-				| OR_GPCM_ACS_DIV2 \
-				| OR_GPCM_XACS \
-				| OR_GPCM_SCY_15 \
-				| OR_GPCM_TRLX_SET \
-				| OR_GPCM_EHTR_SET)
 
 #define CONFIG_SYS_MAX_FLASH_BANKS	1 /* number of banks */
 /* 127 64KB sectors and 8 8KB top sectors per device */
@@ -244,45 +142,14 @@
  */
 #define CONFIG_SYS_NAND_BASE	0xE0600000		/* 0xE0600000 */
 #define CONFIG_SYS_NAND_WINDOW_SIZE	(32 * 1024)	/* 0x00008000 */
-#define CONFIG_SYS_BR1_PRELIM	(CONFIG_SYS_NAND_BASE \
-				| BR_DECC_CHK_GEN	/* Use HW ECC */ \
-				| BR_PS_8		/* 8 bit Port */ \
-				| BR_MS_FCM		/* MSEL = FCM */ \
-				| BR_V)			/* valid */
-#define CONFIG_SYS_OR1_PRELIM	(P2SZ_TO_AM(CONFIG_SYS_NAND_WINDOW_SIZE) \
-				| OR_FCM_CSCT \
-				| OR_FCM_CST \
-				| OR_FCM_CHT \
-				| OR_FCM_SCY_1 \
-				| OR_FCM_TRLX \
-				| OR_FCM_EHTR)
 				/* 0xFFFF8396 */
 
-#define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_NAND_BASE
-#define CONFIG_SYS_LBLAWAR1_PRELIM	(LBLAWAR_EN | LBLAWAR_32KB)
-
 #ifdef CONFIG_VSC7385_ENET
 #define CONFIG_TSEC2
 					/* VSC7385 Base address on CS2 */
 #define CONFIG_SYS_VSC7385_BASE		0xF0000000
 #define CONFIG_SYS_VSC7385_SIZE		(128 * 1024) /* 0x00020000 */
-#define CONFIG_SYS_BR2_PRELIM		(CONFIG_SYS_VSC7385_BASE \
-					| BR_PS_8	/* 8-bit port */ \
-					| BR_MS_GPCM	/* MSEL = GPCM */ \
-					| BR_V)		/* valid */
-					/* 0xF0000801 */
-#define CONFIG_SYS_OR2_PRELIM		(P2SZ_TO_AM(CONFIG_SYS_VSC7385_SIZE) \
-					| OR_GPCM_CSNT \
-					| OR_GPCM_XACS \
-					| OR_GPCM_SCY_15 \
-					| OR_GPCM_SETA \
-					| OR_GPCM_TRLX_SET \
-					| OR_GPCM_EHTR_SET)
 					/* 0xFFFE09FF */
-/* Access window base at VSC7385 base */
-#define CONFIG_SYS_LBLAWBAR2_PRELIM	CONFIG_SYS_VSC7385_BASE
-/* Access window size 128K */
-#define CONFIG_SYS_LBLAWAR2_PRELIM	(LBLAWAR_EN | LBLAWAR_128KB)
 /* The flash address and size of the VSC7385 firmware image */
 #define CONFIG_VSC7385_IMAGE		0xFE7FE000
 #define CONFIG_VSC7385_IMAGE_SIZE	8192
@@ -419,52 +286,6 @@
 #define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
 
 /*
- * Core HID Setup
- */
-#define CONFIG_SYS_HID0_INIT	0x000000000
-#define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK | \
-				 HID0_ENABLE_INSTRUCTION_CACHE | \
-				 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
-#define CONFIG_SYS_HID2		HID2_HBE
-
-/*
- * MMU Setup
- */
-
-/* DDR: cache cacheable */
-#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \
-					BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \
-					BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
-
-/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
-#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_IMMR | BATL_PP_RW | \
-			BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \
-					BATU_VP)
-#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
-
-/* FLASH: icache cacheable, but dcache-inhibit and guarded */
-#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
-					BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \
-					BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT2L	(CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
-					BATL_CACHEINHIBIT | \
-					BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
-
-/* Stack in dcache: cacheable, no memory coherence */
-#define CONFIG_SYS_IBAT3L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
-#define CONFIG_SYS_IBAT3U	(CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
-					BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
-
-/*
  * Environment Configuration
  */
 
diff --git a/include/configs/MPC8313ERDB.h b/include/configs/MPC8313ERDB_NAND.h
index cfa5b56524..4153d609be 100644
--- a/include/configs/MPC8313ERDB.h
+++ b/include/configs/MPC8313ERDB_NAND.h
@@ -13,11 +13,7 @@
  * High Level Configuration Options
  */
 #define CONFIG_E300		1
-#define CONFIG_MPC831x		1
-#define CONFIG_MPC8313		1
-#define CONFIG_MPC8313ERDB	1
 
-#ifdef CONFIG_NAND
 #define CONFIG_SPL_INIT_MINIMAL
 #define CONFIG_SPL_FLUSH_IMAGE
 #define CONFIG_SPL_TARGET		"u-boot-with-spl.bin"
@@ -42,8 +38,6 @@
 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE_SPL /* start of monitor */
 #endif
 
-#endif /* CONFIG_NAND */
-
 #ifndef CONFIG_SYS_MONITOR_BASE
 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
 #endif
@@ -60,19 +54,7 @@
 #define CONFIG_VSC7385_ENET
 #define CONFIG_TSEC2
 
-#ifdef CONFIG_SYS_66MHZ
-#define CONFIG_83XX_CLKIN	66666667	/* in Hz */
-#elif defined(CONFIG_SYS_33MHZ)
-#define CONFIG_83XX_CLKIN	33333333	/* in Hz */
-#else
-#error Unknown oscillator frequency.
-#endif
-
-#define CONFIG_SYS_CLK_FREQ	CONFIG_83XX_CLKIN
-
-#define CONFIG_SYS_IMMR		0xE0000000
-
-#if defined(CONFIG_NAND) && !defined(CONFIG_SPL_BUILD)
+#if !defined(CONFIG_SPL_BUILD)
 #define CONFIG_DEFAULT_IMMR	CONFIG_SYS_IMMR
 #endif
 
@@ -85,9 +67,6 @@
  */
 #define CONFIG_SYS_8313ERDB_BROKEN_PMC 1
 
-#define CONFIG_SYS_ACR_PIPE_DEP	3	/* Arbiter pipeline depth (0-3) */
-#define CONFIG_SYS_ACR_RPTCNT		3	/* Arbiter repeat count (0-7) */
-
 /*
  * Device configurations
  */
@@ -107,9 +86,7 @@
 /*
  * DDR Setup
  */
-#define CONFIG_SYS_DDR_BASE		0x00000000 /* DDR is system memory*/
-#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_SDRAM_BASE		0x00000000 /* DDR is system memory*/
 
 /*
  * Manually set up DDR parameters, as this board does not
@@ -186,21 +163,6 @@
 #define CONFIG_SYS_FLASH_SIZE		8	/* flash size in MB */
 #define CONFIG_SYS_FLASH_EMPTY_INFO		/* display empty sectors */
 
-#define CONFIG_SYS_NOR_BR_PRELIM	(CONFIG_SYS_FLASH_BASE \
-					| BR_PS_16	/* 16 bit port */ \
-					| BR_MS_GPCM	/* MSEL = GPCM */ \
-					| BR_V)		/* valid */
-#define CONFIG_SYS_NOR_OR_PRELIM	(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
-				| OR_GPCM_XACS \
-				| OR_GPCM_SCY_9 \
-				| OR_GPCM_EHTR \
-				| OR_GPCM_EAD)
-				/* 0xFF006FF7	TODO SLOW 16 MB flash size */
-					/* window base at flash base */
-#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
-					/* 16 MB window size */
-#define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_16MB)
-
 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
 #define CONFIG_SYS_MAX_FLASH_SECT	135	/* sectors per device */
 
@@ -224,20 +186,8 @@
 #define CONFIG_SYS_MONITOR_LEN	(512 * 1024)	/* Reserve 512 kB for Mon */
 #define CONFIG_SYS_MALLOC_LEN	(512 * 1024)	/* Reserved for malloc */
 
-/*
- * Local Bus LCRR and LBCR regs
- */
-#define CONFIG_SYS_LCRR_EADC	LCRR_EADC_1
-#define CONFIG_SYS_LCRR_CLKDIV	LCRR_CLKDIV_4
-#define CONFIG_SYS_LBC_LBCR	(0x00040000 /* TODO */ \
-				| (0xFF << LBCR_BMT_SHIFT) \
-				| 0xF)	/* 0x0004ff0f */
-
-				/* LB refresh timer prescal, 266MHz/32 */
-#define CONFIG_SYS_LBC_MRTPR	0x20000000  /*TODO */
-
 /* drivers/mtd/nand/raw/nand.c */
-#if defined(CONFIG_NAND) && defined(CONFIG_SPL_BUILD)
+#if defined(CONFIG_SPL_BUILD)
 #define CONFIG_SYS_NAND_BASE		0xFFF00000
 #else
 #define CONFIG_SYS_NAND_BASE		0xE2800000
@@ -250,59 +200,14 @@
 #define CONFIG_SYS_NAND_BLOCK_SIZE 16384
 #define CONFIG_SYS_NAND_WINDOW_SIZE (32 * 1024)
 
-#define CONFIG_SYS_NAND_BR_PRELIM	(CONFIG_SYS_NAND_BASE \
-				| BR_DECC_CHK_GEN	/* Use HW ECC */ \
-				| BR_PS_8		/* 8 bit port */ \
-				| BR_MS_FCM		/* MSEL = FCM */ \
-				| BR_V)			/* valid */
-#define CONFIG_SYS_NAND_OR_PRELIM	\
-				(P2SZ_TO_AM(CONFIG_SYS_NAND_WINDOW_SIZE) \
-				| OR_FCM_CSCT \
-				| OR_FCM_CST \
-				| OR_FCM_CHT \
-				| OR_FCM_SCY_1 \
-				| OR_FCM_TRLX \
-				| OR_FCM_EHTR)
-				/* 0xFFFF8396 */
-
-#ifdef CONFIG_NAND
-#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM
-#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM
-#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NOR_BR_PRELIM
-#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NOR_OR_PRELIM
-#else
-#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NOR_BR_PRELIM
-#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NOR_OR_PRELIM
-#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM
-#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM
-#endif
-
-#define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_NAND_BASE
-#define CONFIG_SYS_LBLAWAR1_PRELIM	(LBLAWAR_EN | LBLAWAR_32KB)
-
-#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM
-#define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM
+/* Still needed for spl_minimal.c */
+#define CONFIG_SYS_NAND_BR_PRELIM CONFIG_SYS_BR0_PRELIM
+#define CONFIG_SYS_NAND_OR_PRELIM CONFIG_SYS_OR0_PRELIM
 
 /* local bus write LED / read status buffer (BCSR) mapping */
 #define CONFIG_SYS_BCSR_ADDR		0xFA000000
 #define CONFIG_SYS_BCSR_SIZE		(32 * 1024)	/* 0x00008000 */
 					/* map at 0xFA000000 on LCS3 */
-#define CONFIG_SYS_BR3_PRELIM		(CONFIG_SYS_BCSR_ADDR \
-					| BR_PS_8	/* 8 bit port */ \
-					| BR_MS_GPCM	/* MSEL = GPCM */ \
-					| BR_V)		/* valid */
-					/* 0xFA000801 */
-#define CONFIG_SYS_OR3_PRELIM		(P2SZ_TO_AM(CONFIG_SYS_BCSR_SIZE) \
-					| OR_GPCM_CSNT \
-					| OR_GPCM_ACS_DIV2 \
-					| OR_GPCM_XACS \
-					| OR_GPCM_SCY_15 \
-					| OR_GPCM_TRLX_SET \
-					| OR_GPCM_EHTR_SET \
-					| OR_GPCM_EAD)
-					/* 0xFFFF8FF7 */
-#define CONFIG_SYS_LBLAWBAR3_PRELIM	CONFIG_SYS_BCSR_ADDR
-#define CONFIG_SYS_LBLAWAR3_PRELIM	(LBLAWAR_EN | LBLAWAR_32KB)
 
 /* Vitesse 7385 */
 
@@ -312,23 +217,6 @@
 #define CONFIG_SYS_VSC7385_BASE		0xF0000000
 #define CONFIG_SYS_VSC7385_SIZE		(128 * 1024)	/* 0x00020000 */
 
-#define CONFIG_SYS_BR2_PRELIM		(CONFIG_SYS_VSC7385_BASE \
-					| BR_PS_8	/* 8 bit port */ \
-					| BR_MS_GPCM	/* MSEL = GPCM */ \
-					| BR_V)		/* valid */
-#define CONFIG_SYS_OR2_PRELIM		(P2SZ_TO_AM(CONFIG_SYS_VSC7385_SIZE) \
-					| OR_GPCM_CSNT \
-					| OR_GPCM_XACS \
-					| OR_GPCM_SCY_15 \
-					| OR_GPCM_SETA \
-					| OR_GPCM_TRLX_SET \
-					| OR_GPCM_EHTR_SET \
-					| OR_GPCM_EAD)
-					/* 0xFFFE09FF */
-
-					/* Access window base at VSC7385 base */
-#define CONFIG_SYS_LBLAWBAR2_PRELIM	CONFIG_SYS_VSC7385_BASE
-#define CONFIG_SYS_LBLAWAR2_PRELIM	(LBLAWAR_EN | LBLAWAR_128KB)
 
 #endif
 
@@ -409,25 +297,12 @@
 /*
  * Environment
  */
-#if defined(CONFIG_NAND)
-	#define CONFIG_ENV_OFFSET		(512 * 1024)
-	#define CONFIG_ENV_SECT_SIZE	CONFIG_SYS_NAND_BLOCK_SIZE
-	#define CONFIG_ENV_SIZE		CONFIG_ENV_SECT_SIZE
-	#define CONFIG_ENV_SIZE_REDUND	CONFIG_ENV_SIZE
-	#define CONFIG_ENV_RANGE		(CONFIG_ENV_SECT_SIZE * 4)
-	#define CONFIG_ENV_OFFSET_REDUND	\
-					(CONFIG_ENV_OFFSET + CONFIG_ENV_RANGE)
-#elif !defined(CONFIG_SYS_RAMBOOT)
-	#define CONFIG_ENV_ADDR		\
-			(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
-	#define CONFIG_ENV_SECT_SIZE	0x10000	/* 64K(one sector) for env */
-	#define CONFIG_ENV_SIZE		0x2000
-
-/* Address and size of Redundant Environment Sector */
-#else
-	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
-	#define CONFIG_ENV_SIZE		0x2000
-#endif
+#define CONFIG_ENV_OFFSET		(512 * 1024)
+#define CONFIG_ENV_SECT_SIZE	CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_SIZE		CONFIG_ENV_SECT_SIZE
+#define CONFIG_ENV_SIZE_REDUND	CONFIG_ENV_SIZE
+#define CONFIG_ENV_RANGE		(CONFIG_ENV_SECT_SIZE * 4)
+#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + CONFIG_ENV_RANGE)
 
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
@@ -461,134 +336,13 @@
 
 #define CONFIG_SYS_RCWH_PCIHOST 0x80000000	/* PCIHOST  */
 
-#ifdef CONFIG_SYS_66MHZ
-
-/* 66MHz IN, 133MHz CSB, 266 DDR, 266 CORE */
-/* 0x62040000 */
-#define CONFIG_SYS_HRCW_LOW (\
-	0x20000000 /* reserved, must be set */ |\
-	HRCWL_DDRCM |\
-	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
-	HRCWL_DDR_TO_SCB_CLK_2X1 |\
-	HRCWL_CSB_TO_CLKIN_2X1 |\
-	HRCWL_CORE_TO_CSB_2X1)
-
-#define CONFIG_SYS_NS16550_CLK (CONFIG_83XX_CLKIN * 2)
-
-#elif defined(CONFIG_SYS_33MHZ)
-
-/* 33MHz IN, 165MHz CSB, 330 DDR, 330 CORE */
-/* 0x65040000 */
-#define CONFIG_SYS_HRCW_LOW (\
-	0x20000000 /* reserved, must be set */ |\
-	HRCWL_DDRCM |\
-	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
-	HRCWL_DDR_TO_SCB_CLK_2X1 |\
-	HRCWL_CSB_TO_CLKIN_5X1 |\
-	HRCWL_CORE_TO_CSB_2X1)
-
-#define CONFIG_SYS_NS16550_CLK (CONFIG_83XX_CLKIN * 5)
-
-#endif
-
-#define CONFIG_SYS_HRCW_HIGH_BASE (\
-	HRCWH_PCI_HOST |\
-	HRCWH_PCI1_ARBITER_ENABLE |\
-	HRCWH_CORE_ENABLE |\
-	HRCWH_BOOTSEQ_DISABLE |\
-	HRCWH_SW_WATCHDOG_DISABLE |\
-	HRCWH_TSEC1M_IN_RGMII |\
-	HRCWH_TSEC2M_IN_RGMII |\
-	HRCWH_BIG_ENDIAN)
-
-#ifdef CONFIG_NAND
-#define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE |\
-		       HRCWH_FROM_0XFFF00100 |\
-		       HRCWH_ROM_LOC_NAND_SP_8BIT |\
-		       HRCWH_RL_EXT_NAND)
-#else
-#define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE |\
-		       HRCWH_FROM_0X00000100 |\
-		       HRCWH_ROM_LOC_LOCAL_16BIT |\
-		       HRCWH_RL_EXT_LEGACY)
-#endif
+#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0))
 
 /* System IO Config */
 #define CONFIG_SYS_SICRH	(SICRH_TSOBI1 | SICRH_TSOBI2)	/* RGMII */
 			/* Enable Internal USB Phy and GPIO on LCD Connector */
 #define CONFIG_SYS_SICRL	(SICRL_USBDR_10 | SICRL_LBC)
 
-#define CONFIG_SYS_HID0_INIT	0x000000000
-#define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK | \
-				 HID0_ENABLE_INSTRUCTION_CACHE | \
-				 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
-
-#define CONFIG_SYS_HID2 HID2_HBE
-
-#define CONFIG_HIGH_BATS	1	/* High BATs supported */
-
-/* DDR @ 0x00000000 */
-#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_RW)
-#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-
-/* PCI @ 0x80000000 */
-#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_RW)
-#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_PCI1_MEM_BASE \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_PCI1_MMIO_BASE \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_PCI1_MMIO_BASE \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-
-/* PCI2 not supported on 8313 */
-#define CONFIG_SYS_IBAT3L	(0)
-#define CONFIG_SYS_IBAT3U	(0)
-#define CONFIG_SYS_IBAT4L	(0)
-#define CONFIG_SYS_IBAT4U	(0)
-
-/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */
-#define CONFIG_SYS_IBAT5L	(CONFIG_SYS_IMMR \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT5U	(CONFIG_SYS_IMMR \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-
-/* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
-#define CONFIG_SYS_IBAT6L	(0xF0000000 | BATL_PP_RW | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT6U	(0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_IBAT7L	(0)
-#define CONFIG_SYS_IBAT7U	(0)
-
-#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
-#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
-#define CONFIG_SYS_DBAT2L	CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
-#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
-#define CONFIG_SYS_DBAT4L	CONFIG_SYS_IBAT4L
-#define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U
-#define CONFIG_SYS_DBAT5L	CONFIG_SYS_IBAT5L
-#define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
-#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
-#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
-#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
-
 /*
  * Environment Configuration
  */
diff --git a/include/configs/MPC8313ERDB_NOR.h b/include/configs/MPC8313ERDB_NOR.h
new file mode 100644
index 0000000000..ff8dedf03e
--- /dev/null
+++ b/include/configs/MPC8313ERDB_NOR.h
@@ -0,0 +1,377 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) Freescale Semiconductor, Inc. 2006, 2010.
+ */
+/*
+ * mpc8313epb board configuration file
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300		1
+
+#ifndef CONFIG_SYS_MONITOR_BASE
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
+#endif
+
+#define CONFIG_PCI_INDIRECT_BRIDGE
+#define CONFIG_FSL_ELBC 1
+
+/*
+ * On-board devices
+ *
+ * TSEC1 is VSC switch
+ * TSEC2 is SoC TSEC
+ */
+#define CONFIG_VSC7385_ENET
+#define CONFIG_TSEC2
+
+#define CONFIG_SYS_MEMTEST_START	0x00001000
+#define CONFIG_SYS_MEMTEST_END		0x07f00000
+
+/* Early revs of this board will lock up hard when attempting
+ * to access the PMC registers, unless a JTAG debugger is
+ * connected, or some resistor modifications are made.
+ */
+#define CONFIG_SYS_8313ERDB_BROKEN_PMC 1
+
+/*
+ * Device configurations
+ */
+
+/* Vitesse 7385 */
+
+#ifdef CONFIG_VSC7385_ENET
+
+#define CONFIG_TSEC1
+
+/* The flash address and size of the VSC7385 firmware image */
+#define CONFIG_VSC7385_IMAGE		0xFE7FE000
+#define CONFIG_VSC7385_IMAGE_SIZE	8192
+
+#endif
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_SYS_SDRAM_BASE		0x00000000 /* DDR is system memory*/
+
+/*
+ * Manually set up DDR parameters, as this board does not
+ * seem to have the SPD connected to I2C.
+ */
+#define CONFIG_SYS_DDR_SIZE	128		/* MB */
+#define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN \
+				| CSCONFIG_ODT_RD_NEVER \
+				| CSCONFIG_ODT_WR_ONLY_CURRENT \
+				| CSCONFIG_ROW_BIT_13 \
+				| CSCONFIG_COL_BIT_10)
+				/* 0x80010102 */
+
+#define CONFIG_SYS_DDR_TIMING_3	0x00000000
+#define CONFIG_SYS_DDR_TIMING_0	((0 << TIMING_CFG0_RWT_SHIFT) \
+				| (0 << TIMING_CFG0_WRT_SHIFT) \
+				| (0 << TIMING_CFG0_RRT_SHIFT) \
+				| (0 << TIMING_CFG0_WWT_SHIFT) \
+				| (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
+				| (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
+				| (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
+				| (2 << TIMING_CFG0_MRS_CYC_SHIFT))
+				/* 0x00220802 */
+#define CONFIG_SYS_DDR_TIMING_1	((3 << TIMING_CFG1_PRETOACT_SHIFT) \
+				| (8 << TIMING_CFG1_ACTTOPRE_SHIFT) \
+				| (3 << TIMING_CFG1_ACTTORW_SHIFT) \
+				| (5 << TIMING_CFG1_CASLAT_SHIFT) \
+				| (10 << TIMING_CFG1_REFREC_SHIFT) \
+				| (3 << TIMING_CFG1_WRREC_SHIFT) \
+				| (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
+				| (2 << TIMING_CFG1_WRTORD_SHIFT))
+				/* 0x3835a322 */
+#define CONFIG_SYS_DDR_TIMING_2	((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
+				| (5 << TIMING_CFG2_CPO_SHIFT) \
+				| (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
+				| (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
+				| (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
+				| (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
+				| (6 << TIMING_CFG2_FOUR_ACT_SHIFT))
+				/* 0x129048c6 */ /* P9-45,may need tuning */
+#define CONFIG_SYS_DDR_INTERVAL	((1296 << SDRAM_INTERVAL_REFINT_SHIFT) \
+				| (1280 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
+				/* 0x05100500 */
+#if defined(CONFIG_DDR_2T_TIMING)
+#define CONFIG_SYS_SDRAM_CFG	(SDRAM_CFG_SREN \
+				| SDRAM_CFG_SDRAM_TYPE_DDR2 \
+				| SDRAM_CFG_DBW_32 \
+				| SDRAM_CFG_2T_EN)
+				/* 0x43088000 */
+#else
+#define CONFIG_SYS_SDRAM_CFG	(SDRAM_CFG_SREN \
+				| SDRAM_CFG_SDRAM_TYPE_DDR2 \
+				| SDRAM_CFG_DBW_32)
+				/* 0x43080000 */
+#endif
+#define CONFIG_SYS_SDRAM_CFG2		0x00401000
+/* set burst length to 8 for 32-bit data path */
+#define CONFIG_SYS_DDR_MODE	((0x4448 << SDRAM_MODE_ESD_SHIFT) \
+				| (0x0632 << SDRAM_MODE_SD_SHIFT))
+				/* 0x44480632 */
+#define CONFIG_SYS_DDR_MODE_2	0x8000C000
+
+#define CONFIG_SYS_DDR_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
+				/*0x02000000*/
+#define CONFIG_SYS_DDRCDR_VALUE	(DDRCDR_EN \
+				| DDRCDR_PZ_NOMZ \
+				| DDRCDR_NZ_NOMZ \
+				| DDRCDR_M_ODR)
+
+/*
+ * FLASH on the Local Bus
+ */
+#define CONFIG_SYS_FLASH_BASE		0xFE000000	/* start of FLASH   */
+#define CONFIG_SYS_FLASH_SIZE		8	/* flash size in MB */
+#define CONFIG_SYS_FLASH_PROTECTION	1	/* Use h/w Flash protection. */
+#define CONFIG_SYS_FLASH_EMPTY_INFO		/* display empty sectors */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	135	/* sectors per device */
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
+
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) && \
+	!defined(CONFIG_SPL_BUILD)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+#define CONFIG_SYS_INIT_RAM_LOCK	1
+#define CONFIG_SYS_INIT_RAM_ADDR	0xFD000000	/* Initial RAM addr */
+#define CONFIG_SYS_INIT_RAM_SIZE	0x1000	/* Size of used area in RAM*/
+
+#define CONFIG_SYS_GBL_DATA_OFFSET	\
+			(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
+#define CONFIG_SYS_MONITOR_LEN	(512 * 1024)	/* Reserve 512 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN	(512 * 1024)	/* Reserved for malloc */
+
+/* drivers/mtd/nand/nand.c */
+#define CONFIG_SYS_NAND_BASE		0xE2800000
+
+#define CONFIG_MTD_PARTITION
+
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_NAND_FSL_ELBC 1
+#define CONFIG_SYS_NAND_BLOCK_SIZE 16384
+#define CONFIG_SYS_NAND_WINDOW_SIZE (32 * 1024)
+
+/* Still needed for spl_minimal.c */
+#define CONFIG_SYS_NAND_BR_PRELIM CONFIG_SYS_BR1_PRELIM
+#define CONFIG_SYS_NAND_OR_PRELIM CONFIG_SYS_OR1_PRELIM
+
+/* local bus write LED / read status buffer (BCSR) mapping */
+#define CONFIG_SYS_BCSR_ADDR		0xFA000000
+#define CONFIG_SYS_BCSR_SIZE		(32 * 1024)	/* 0x00008000 */
+					/* map at 0xFA000000 on LCS3 */
+/* Vitesse 7385 */
+
+#ifdef CONFIG_VSC7385_ENET
+
+					/* VSC7385 Base address on LCS2 */
+#define CONFIG_SYS_VSC7385_BASE		0xF0000000
+#define CONFIG_SYS_VSC7385_SIZE		(128 * 1024)	/* 0x00020000 */
+
+
+#endif
+
+#define CONFIG_MPC83XX_GPIO 1
+
+/*
+ * Serial Port
+ */
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+
+#define CONFIG_SYS_BAUDRATE_TABLE	\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR+0x4500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR+0x4600)
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED	400000
+#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED	400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
+#define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x69} }
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CONFIG_SYS_PCI1_MEM_BASE	0x80000000
+#define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BASE
+#define CONFIG_SYS_PCI1_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCI1_MMIO_BASE	0x90000000
+#define CONFIG_SYS_PCI1_MMIO_PHYS	CONFIG_SYS_PCI1_MMIO_BASE
+#define CONFIG_SYS_PCI1_MMIO_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCI1_IO_BASE	0x00000000
+#define CONFIG_SYS_PCI1_IO_PHYS	0xE2000000
+#define CONFIG_SYS_PCI1_IO_SIZE	0x00100000	/* 1M */
+
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057	/* Motorola */
+
+/*
+ * TSEC
+ */
+
+#define CONFIG_GMII			/* MII PHY management */
+
+#ifdef CONFIG_TSEC1
+#define CONFIG_HAS_ETH0
+#define CONFIG_TSEC1_NAME	"TSEC0"
+#define CONFIG_SYS_TSEC1_OFFSET	0x24000
+#define TSEC1_PHY_ADDR		0x1c
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC1_PHYIDX		0
+#endif
+
+#ifdef CONFIG_TSEC2
+#define CONFIG_HAS_ETH1
+#define CONFIG_TSEC2_NAME	"TSEC1"
+#define CONFIG_SYS_TSEC2_OFFSET	0x25000
+#define TSEC2_PHY_ADDR		4
+#define TSEC2_FLAGS		TSEC_GIGABIT
+#define TSEC2_PHYIDX		0
+#endif
+
+/* Options are: TSEC[0-1] */
+#define CONFIG_ETHPRIME			"TSEC1"
+
+/*
+ * Configure on-board RTC
+ */
+#define CONFIG_RTC_DS1337
+#define CONFIG_SYS_I2C_RTC_ADDR		0x68
+
+/*
+ * Environment
+ */
+#if !defined(CONFIG_SYS_RAMBOOT)
+	#define CONFIG_ENV_ADDR		\
+			(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
+	#define CONFIG_ENV_SECT_SIZE	0x10000	/* 64K(one sector) for env */
+	#define CONFIG_ENV_SIZE		0x2000
+
+/* Address and size of Redundant Environment Sector */
+#else
+	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
+	#define CONFIG_ENV_SIZE		0x2000
+#endif
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+
+/*
+ * Command line configuration.
+ */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
+#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
+
+				/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 256 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+				/* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTMAPSZ	(256 << 20)
+#define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
+
+#define CONFIG_SYS_RCWH_PCIHOST 0x80000000	/* PCIHOST  */
+
+#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0))
+
+/* System IO Config */
+#define CONFIG_SYS_SICRH	(SICRH_TSOBI1 | SICRH_TSOBI2)	/* RGMII */
+			/* Enable Internal USB Phy and GPIO on LCD Connector */
+#define CONFIG_SYS_SICRL	(SICRL_USBDR_10 | SICRL_LBC)
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_NETDEV		"eth1"
+
+#define CONFIG_HOSTNAME		"mpc8313erdb"
+#define CONFIG_ROOTPATH		"/nfs/root/path"
+#define CONFIG_BOOTFILE		"uImage"
+				/* U-Boot image on TFTP server */
+#define CONFIG_UBOOTPATH	"u-boot.bin"
+#define CONFIG_FDTFILE		"mpc8313erdb.dtb"
+
+				/* default location for tftp and bootm */
+#define CONFIG_LOADADDR		800000
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"netdev=" CONFIG_NETDEV "\0"					\
+	"ethprime=TSEC1\0"						\
+	"uboot=" CONFIG_UBOOTPATH "\0"					\
+	"tftpflash=tftpboot $loadaddr $uboot; "				\
+		"protect off " __stringify(CONFIG_SYS_TEXT_BASE)	\
+			" +$filesize; "	\
+		"erase " __stringify(CONFIG_SYS_TEXT_BASE)		\
+			" +$filesize; "	\
+		"cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)	\
+			" $filesize; "	\
+		"protect on " __stringify(CONFIG_SYS_TEXT_BASE)		\
+			" +$filesize; "	\
+		"cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)	\
+			" $filesize\0"	\
+	"fdtaddr=780000\0"						\
+	"fdtfile=" CONFIG_FDTFILE "\0"					\
+	"console=ttyS0\0"						\
+	"setbootargs=setenv bootargs "					\
+		"root=$rootdev rw console=$console,$baudrate $othbootargs\0" \
+	"setipargs=setenv bootargs nfsroot=$serverip:$rootpath "	 \
+		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"\
+							"$netdev:off " \
+		"root=$rootdev rw console=$console,$baudrate $othbootargs\0"
+
+#define CONFIG_NFSBOOTCOMMAND						\
+	"setenv rootdev /dev/nfs;"					\
+	"run setbootargs;"						\
+	"run setipargs;"						\
+	"tftp $loadaddr $bootfile;"					\
+	"tftp $fdtaddr $fdtfile;"					\
+	"bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND						\
+	"setenv rootdev /dev/ram;"					\
+	"run setbootargs;"						\
+	"tftp $ramdiskaddr $ramdiskfile;"				\
+	"tftp $loadaddr $bootfile;"					\
+	"tftp $fdtaddr $fdtfile;"					\
+	"bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/MPC8315ERDB.h b/include/configs/MPC8315ERDB.h
index 0ccf4acb82..521c5ca6ee 100644
--- a/include/configs/MPC8315ERDB.h
+++ b/include/configs/MPC8315ERDB.h
@@ -22,49 +22,6 @@
  * High Level Configuration Options
  */
 #define CONFIG_E300		1 /* E300 family */
-#define CONFIG_MPC831x		1 /* MPC831x CPU family */
-#define CONFIG_MPC8315		1 /* MPC8315 CPU specific */
-#define CONFIG_MPC8315ERDB	1 /* MPC8315ERDB board specific */
-
-/*
- * System Clock Setup
- */
-#define CONFIG_83XX_CLKIN	66666667 /* in Hz */
-#define CONFIG_SYS_CLK_FREQ	CONFIG_83XX_CLKIN
-
-/*
- * Hardware Reset Configuration Word
- * if CLKIN is 66.66MHz, then
- * CSB = 133MHz, CORE = 400MHz, DDRC = 266MHz, LBC = 133MHz
- */
-#define CONFIG_SYS_HRCW_LOW (\
-	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
-	HRCWL_DDR_TO_SCB_CLK_2X1 |\
-	HRCWL_SVCOD_DIV_2 |\
-	HRCWL_CSB_TO_CLKIN_2X1 |\
-	HRCWL_CORE_TO_CSB_3X1)
-#define CONFIG_SYS_HRCW_HIGH_BASE (\
-	HRCWH_PCI_HOST |\
-	HRCWH_PCI1_ARBITER_ENABLE |\
-	HRCWH_CORE_ENABLE |\
-	HRCWH_BOOTSEQ_DISABLE |\
-	HRCWH_SW_WATCHDOG_DISABLE |\
-	HRCWH_TSEC1M_IN_RGMII |\
-	HRCWH_TSEC2M_IN_RGMII |\
-	HRCWH_BIG_ENDIAN |\
-	HRCWH_LALE_NORMAL)
-
-#ifdef CONFIG_NAND_SPL
-#define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE |\
-		       HRCWH_FROM_0XFFF00100 |\
-		       HRCWH_ROM_LOC_NAND_SP_8BIT |\
-		       HRCWH_RL_EXT_NAND)
-#else
-#define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE |\
-		       HRCWH_FROM_0X00000100 |\
-		       HRCWH_ROM_LOC_LOCAL_16BIT |\
-		       HRCWH_RL_EXT_LEGACY)
-#endif
 
 /*
  * System IO Config
@@ -75,23 +32,9 @@
 #define CONFIG_HWCONFIG
 
 /*
- * IMMR new address
- */
-#define CONFIG_SYS_IMMR		0xE0000000
-
-/*
- * Arbiter Setup
- */
-#define CONFIG_SYS_ACR_PIPE_DEP	3 /* Arbiter pipeline depth is 4 */
-#define CONFIG_SYS_ACR_RPTCNT	3 /* Arbiter repeat count is 4 */
-#define CONFIG_SYS_SPCR_TSECEP	3 /* eTSEC emergency priority is highest */
-
-/*
  * DDR Setup
  */
-#define CONFIG_SYS_DDR_BASE		0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_SDRAM_BASE		0x00000000 /* DDR is system memory */
 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
 #define CONFIG_SYS_DDRCDR_VALUE	(DDRCDR_EN \
 				| DDRCDR_PZ_LOZ \
@@ -173,13 +116,7 @@
 #define CONFIG_SYS_GBL_DATA_OFFSET	\
 			(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 
-/*
- * Local Bus Configuration & Clock Setup
- */
-#define CONFIG_SYS_LCRR_DBYP	LCRR_DBYP
-#define CONFIG_SYS_LCRR_CLKDIV		LCRR_CLKDIV_2
-#define CONFIG_SYS_LBC_LBCR		0x00040000
-#define CONFIG_FSL_ELBC		1
+#define CONFIG_FSL_ELBC
 
 /*
  * FLASH on the Local Bus
@@ -189,24 +126,6 @@
 #define CONFIG_SYS_FLASH_BASE		0xFE000000 /* FLASH base address */
 #define CONFIG_SYS_FLASH_SIZE		8	/* FLASH size is 8M */
 
-					/* Window base at flash base */
-#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_8MB)
-
-#define CONFIG_SYS_NOR_BR_PRELIM	(CONFIG_SYS_FLASH_BASE \
-					| BR_PS_16	/* 16 bit port */ \
-					| BR_MS_GPCM	/* MSEL = GPCM */ \
-					| BR_V)		/* valid */
-#define CONFIG_SYS_NOR_OR_PRELIM	(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
-					| OR_UPM_XAM \
-					| OR_GPCM_CSNT \
-					| OR_GPCM_ACS_DIV2 \
-					| OR_GPCM_XACS \
-					| OR_GPCM_SCY_15 \
-					| OR_GPCM_TRLX_SET \
-					| OR_GPCM_EHTR_SET \
-					| OR_GPCM_EAD)
-
 #define CONFIG_SYS_MAX_FLASH_BANKS	1 /* number of banks */
 /* 127 64KB sectors and 8 8KB top sectors per device */
 #define CONFIG_SYS_MAX_FLASH_SECT	135
@@ -238,31 +157,11 @@
 #define CONFIG_SYS_NAND_U_BOOT_OFFS  16384
 #define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000
 
-#define CONFIG_SYS_NAND_BR_PRELIM	(CONFIG_SYS_NAND_BASE \
-				| BR_DECC_CHK_GEN	/* Use HW ECC */ \
-				| BR_PS_8		/* 8 bit port */ \
-				| BR_MS_FCM		/* MSEL = FCM */ \
-				| BR_V)			/* valid */
-#define CONFIG_SYS_NAND_OR_PRELIM	\
-				(P2SZ_TO_AM(CONFIG_SYS_NAND_WINDOW_SIZE) \
-				| OR_FCM_CSCT \
-				| OR_FCM_CST \
-				| OR_FCM_CHT \
-				| OR_FCM_SCY_1 \
-				| OR_FCM_TRLX \
-				| OR_FCM_EHTR)
-				/* 0xFFFF8396 */
-
-#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NOR_BR_PRELIM
-#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NOR_OR_PRELIM
-#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM
-#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM
-
-#define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_NAND_BASE
-#define CONFIG_SYS_LBLAWAR1_PRELIM	(LBLAWAR_EN | LBLAWAR_32KB)
-
-#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM
-#define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM
+
+
+/* Still needed for spl_minimal.c */
+#define CONFIG_SYS_NAND_BR_PRELIM CONFIG_SYS_BR1_PRELIM
+#define CONFIG_SYS_NAND_OR_PRELIM CONFIG_SYS_OR1_PRELIM
 
 #if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE && \
 	!defined(CONFIG_NAND_SPL)
@@ -276,7 +175,7 @@
  */
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		(CONFIG_83XX_CLKIN * 2)
+#define CONFIG_SYS_NS16550_CLK		(get_bus_freq(0))
 
 #define CONFIG_SYS_BAUDRATE_TABLE  \
 		{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
@@ -438,97 +337,8 @@
 #define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
 
 /*
- * Core HID Setup
- */
-#define CONFIG_SYS_HID0_INIT	0x000000000
-#define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK | \
-				 HID0_ENABLE_INSTRUCTION_CACHE | \
-				 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
-#define CONFIG_SYS_HID2		HID2_HBE
-
-/*
  * MMU Setup
  */
-#define CONFIG_HIGH_BATS	1	/* High BATs supported */
-
-/* DDR: cache cacheable */
-#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE \
-				| BATU_BL_128M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
-
-/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
-#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_IMMR \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_IMMR \
-				| BATU_BL_8M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
-
-/* FLASH: icache cacheable, but dcache-inhibit and guarded */
-#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_FLASH_BASE \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_FLASH_BASE \
-				| BATU_BL_32M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT2L	(CONFIG_SYS_FLASH_BASE \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
-
-/* Stack in dcache: cacheable, no memory coherence */
-#define CONFIG_SYS_IBAT3L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
-#define CONFIG_SYS_IBAT3U	(CONFIG_SYS_INIT_RAM_ADDR \
-				| BATU_BL_128K \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
-
-/* PCI MEM space: cacheable */
-#define CONFIG_SYS_IBAT4L	(CONFIG_SYS_PCI_MEM_PHYS \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT4U	(CONFIG_SYS_PCI_MEM_PHYS \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT4L	CONFIG_SYS_IBAT4L
-#define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U
-
-/* PCI MMIO space: cache-inhibit and guarded */
-#define CONFIG_SYS_IBAT5L	(CONFIG_SYS_PCI_MMIO_PHYS \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT5U	(CONFIG_SYS_PCI_MMIO_PHYS \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT5L	CONFIG_SYS_IBAT5L
-#define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
-
-#define CONFIG_SYS_IBAT6L	0
-#define CONFIG_SYS_IBAT6U	0
-#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
-#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
-
-#define CONFIG_SYS_IBAT7L	0
-#define CONFIG_SYS_IBAT7U	0
-#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
diff --git a/include/configs/MPC8323ERDB.h b/include/configs/MPC8323ERDB.h
index 578202f3be..418c6729e1 100644
--- a/include/configs/MPC8323ERDB.h
+++ b/include/configs/MPC8323ERDB.h
@@ -14,40 +14,6 @@
  */
 #define CONFIG_E300		1	/* E300 family */
 #define CONFIG_QE		1	/* Has QE */
-#define CONFIG_MPC832x		1	/* MPC832x CPU specific */
-
-/*
- * System Clock Setup
- */
-#define CONFIG_83XX_CLKIN	66666667	/* in Hz */
-
-#ifndef CONFIG_SYS_CLK_FREQ
-#define CONFIG_SYS_CLK_FREQ	CONFIG_83XX_CLKIN
-#endif
-
-/*
- * Hardware Reset Configuration Word
- */
-#define CONFIG_SYS_HRCW_LOW (\
-	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
-	HRCWL_DDR_TO_SCB_CLK_2X1 |\
-	HRCWL_VCO_1X2 |\
-	HRCWL_CSB_TO_CLKIN_2X1 |\
-	HRCWL_CORE_TO_CSB_2_5X1 |\
-	HRCWL_CE_PLL_VCO_DIV_2 |\
-	HRCWL_CE_PLL_DIV_1X1 |\
-	HRCWL_CE_TO_PLL_1X3)
-
-#define CONFIG_SYS_HRCW_HIGH (\
-	HRCWH_PCI_HOST |\
-	HRCWH_PCI1_ARBITER_ENABLE |\
-	HRCWH_CORE_ENABLE |\
-	HRCWH_FROM_0X00000100 |\
-	HRCWH_BOOTSEQ_DISABLE |\
-	HRCWH_SW_WATCHDOG_DISABLE |\
-	HRCWH_ROM_LOC_LOCAL_16BIT |\
-	HRCWH_BIG_ENDIAN |\
-	HRCWH_LALE_NORMAL)
 
 /*
  * System IO Config
@@ -55,24 +21,9 @@
 #define CONFIG_SYS_SICRL		0x00000000
 
 /*
- * IMMR new address
- */
-#define CONFIG_SYS_IMMR		0xE0000000
-
-/*
- * System performance
- */
-#define CONFIG_SYS_ACR_PIPE_DEP	3	/* Arbiter pipeline depth (0-3) */
-#define CONFIG_SYS_ACR_RPTCNT	3	/* Arbiter repeat count (0-7) */
-/* (0-1) Optimize transactions between CSB and the SEC and QUICC Engine block */
-#define CONFIG_SYS_SPCR_OPT	1
-
-/*
  * DDR Setup
  */
-#define CONFIG_SYS_DDR_BASE	0x00000000	/* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE	CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_SDRAM_BASE	0x00000000	/* DDR is system memory */
 
 #undef CONFIG_SPD_EEPROM
 #if defined(CONFIG_SPD_EEPROM)
@@ -163,36 +114,12 @@
 			(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 
 /*
- * Local Bus Configuration & Clock Setup
- */
-#define CONFIG_SYS_LCRR_DBYP		LCRR_DBYP
-#define CONFIG_SYS_LCRR_CLKDIV		LCRR_CLKDIV_2
-#define CONFIG_SYS_LBC_LBCR		0x00000000
-
-/*
  * FLASH on the Local Bus
  */
 #define CONFIG_SYS_FLASH_BASE	0xFE000000	/* FLASH base address */
 #define CONFIG_SYS_FLASH_SIZE		16	/* FLASH size is 16M */
 
-					/* Window base at flash base */
-#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_32MB)
-
-#define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE \
-				| BR_PS_16	/* 16 bit port */ \
-				| BR_MS_GPCM	/* MSEL = GPCM */ \
-				| BR_V)		/* valid */
-#define CONFIG_SYS_OR0_PRELIM	(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
-				| OR_GPCM_XAM \
-				| OR_GPCM_CSNT \
-				| OR_GPCM_ACS_DIV2 \
-				| OR_GPCM_XACS \
-				| OR_GPCM_SCY_15 \
-				| OR_GPCM_TRLX_SET \
-				| OR_GPCM_EHTR_SET \
-				| OR_GPCM_EAD)
-				/* 0xFE006FF7 */
+
 
 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
 #define CONFIG_SYS_MAX_FLASH_SECT	128	/* sectors per device */
@@ -323,109 +250,6 @@
 #define CONFIG_SYS_BOOTMAPSZ		(256 << 20)
 #define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
 
-/*
- * Core HID Setup
- */
-#define CONFIG_SYS_HID0_INIT	0x000000000
-#define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK | \
-				 HID0_ENABLE_INSTRUCTION_CACHE)
-#define CONFIG_SYS_HID2		HID2_HBE
-
-/*
- * MMU Setup
- */
-#define CONFIG_HIGH_BATS	1	/* High BATs supported */
-
-/* DDR: cache cacheable */
-#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
-
-/* IMMRBAR & PCI IO: cache-inhibit and guarded */
-#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_IMMR \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_IMMR \
-				| BATU_BL_4M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
-
-/* FLASH: icache cacheable, but dcache-inhibit and guarded */
-#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_FLASH_BASE \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_FLASH_BASE \
-				| BATU_BL_32M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT2L	(CONFIG_SYS_FLASH_BASE \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
-
-#define CONFIG_SYS_IBAT3L	(0)
-#define CONFIG_SYS_IBAT3U	(0)
-#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
-
-/* Stack in dcache: cacheable, no memory coherence */
-#define CONFIG_SYS_IBAT4L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
-#define CONFIG_SYS_IBAT4U	(CONFIG_SYS_INIT_RAM_ADDR \
-				| BATU_BL_128K \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT4L	CONFIG_SYS_IBAT4L
-#define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U
-
-#ifdef CONFIG_PCI
-/* PCI MEM space: cacheable */
-#define CONFIG_SYS_IBAT5L	(CONFIG_SYS_PCI1_MEM_PHYS \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT5U	(CONFIG_SYS_PCI1_MEM_PHYS \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT5L	CONFIG_SYS_IBAT5L
-#define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
-/* PCI MMIO space: cache-inhibit and guarded */
-#define CONFIG_SYS_IBAT6L	(CONFIG_SYS_PCI1_MMIO_PHYS \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT6U	(CONFIG_SYS_PCI1_MMIO_PHYS \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
-#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
-#else
-#define CONFIG_SYS_IBAT5L	(0)
-#define CONFIG_SYS_IBAT5U	(0)
-#define CONFIG_SYS_IBAT6L	(0)
-#define CONFIG_SYS_IBAT6U	(0)
-#define CONFIG_SYS_DBAT5L	CONFIG_SYS_IBAT5L
-#define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
-#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
-#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
-#endif
-
-/* Nothing in BAT7 */
-#define CONFIG_SYS_IBAT7L	(0)
-#define CONFIG_SYS_IBAT7U	(0)
-#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
-
 #if (CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
 #endif
diff --git a/include/configs/MPC832XEMDS.h b/include/configs/MPC832XEMDS.h
index 8f11d9b3a4..df9cc48417 100644
--- a/include/configs/MPC832XEMDS.h
+++ b/include/configs/MPC832XEMDS.h
@@ -11,58 +11,6 @@
  */
 #define CONFIG_E300		1	/* E300 family */
 #define CONFIG_QE		1	/* Has QE */
-#define CONFIG_MPC832x		1	/* MPC832x CPU specific */
-#define CONFIG_MPC832XEMDS	1	/* MPC832XEMDS board specific */
-
-/*
- * System Clock Setup
- */
-#ifdef CONFIG_PCISLAVE
-#define CONFIG_83XX_PCICLK	66000000	/* in HZ */
-#else
-#define CONFIG_83XX_CLKIN	66000000	/* in Hz */
-#endif
-
-#ifndef CONFIG_SYS_CLK_FREQ
-#define CONFIG_SYS_CLK_FREQ	66000000
-#endif
-
-/*
- * Hardware Reset Configuration Word
- */
-#define CONFIG_SYS_HRCW_LOW (\
-	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
-	HRCWL_DDR_TO_SCB_CLK_2X1 |\
-	HRCWL_VCO_1X2 |\
-	HRCWL_CSB_TO_CLKIN_2X1 |\
-	HRCWL_CORE_TO_CSB_2X1 |\
-	HRCWL_CE_PLL_VCO_DIV_2 |\
-	HRCWL_CE_PLL_DIV_1X1 |\
-	HRCWL_CE_TO_PLL_1X3)
-
-#ifdef CONFIG_PCISLAVE
-#define CONFIG_SYS_HRCW_HIGH (\
-	HRCWH_PCI_AGENT |\
-	HRCWH_PCI1_ARBITER_DISABLE |\
-	HRCWH_CORE_ENABLE |\
-	HRCWH_FROM_0XFFF00100 |\
-	HRCWH_BOOTSEQ_DISABLE |\
-	HRCWH_SW_WATCHDOG_DISABLE |\
-	HRCWH_ROM_LOC_LOCAL_16BIT |\
-	HRCWH_BIG_ENDIAN |\
-	HRCWH_LALE_NORMAL)
-#else
-#define CONFIG_SYS_HRCW_HIGH (\
-	HRCWH_PCI_HOST |\
-	HRCWH_PCI1_ARBITER_ENABLE |\
-	HRCWH_CORE_ENABLE |\
-	HRCWH_FROM_0X00000100 |\
-	HRCWH_BOOTSEQ_DISABLE |\
-	HRCWH_SW_WATCHDOG_DISABLE |\
-	HRCWH_ROM_LOC_LOCAL_16BIT |\
-	HRCWH_BIG_ENDIAN |\
-	HRCWH_LALE_NORMAL)
-#endif
 
 /*
  * System IO Config
@@ -70,16 +18,9 @@
 #define CONFIG_SYS_SICRL		0x00000000
 
 /*
- * IMMR new address
- */
-#define CONFIG_SYS_IMMR		0xE0000000
-
-/*
  * DDR Setup
  */
-#define CONFIG_SYS_DDR_BASE	0x00000000	/* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE	CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_SDRAM_BASE	0x00000000	/* DDR is system memory */
 #define CONFIG_SYS_DDRCDR	0x73000002	/* DDR II voltage is 1.8V */
 
 #undef CONFIG_SPD_EEPROM
@@ -173,36 +114,11 @@
 			(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 
 /*
- * Local Bus Configuration & Clock Setup
- */
-#define CONFIG_SYS_LCRR_DBYP		LCRR_DBYP
-#define CONFIG_SYS_LCRR_CLKDIV		LCRR_CLKDIV_2
-#define CONFIG_SYS_LBC_LBCR		0x00000000
-
-/*
  * FLASH on the Local Bus
  */
 #define CONFIG_SYS_FLASH_BASE	0xFE000000	/* FLASH base address */
 #define CONFIG_SYS_FLASH_SIZE	16	/* FLASH size is 16M */
 
-					/* Window base at flash base */
-#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_32MB)
-
-#define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE \
-				| BR_PS_16	/* 16 bit port */ \
-				| BR_MS_GPCM	/* MSEL = GPCM */ \
-				| BR_V)		/* valid */
-#define CONFIG_SYS_OR0_PRELIM	(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
-				| OR_GPCM_XAM \
-				| OR_GPCM_CSNT \
-				| OR_GPCM_ACS_DIV2 \
-				| OR_GPCM_XACS \
-				| OR_GPCM_SCY_15 \
-				| OR_GPCM_TRLX_SET \
-				| OR_GPCM_EHTR_SET \
-				| OR_GPCM_EAD)
-				/* 0xfe006ff7 */
 
 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
 #define CONFIG_SYS_MAX_FLASH_SECT	128	/* sectors per device */
@@ -214,22 +130,7 @@
  */
 #define CONFIG_SYS_BCSR			0xF8000000
 					/* Access window base at BCSR base */
-#define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_BCSR
-#define CONFIG_SYS_LBLAWAR1_PRELIM	(LBLAWAR_EN | LBLAWAR_32KB)
-
-#define CONFIG_SYS_BR1_PRELIM		(CONFIG_SYS_BCSR \
-					| BR_PS_8 \
-					| BR_MS_GPCM \
-					| BR_V)
-#define CONFIG_SYS_OR1_PRELIM		(OR_AM_32KB \
-					| OR_GPCM_XAM \
-					| OR_GPCM_CSNT \
-					| OR_GPCM_XACS \
-					| OR_GPCM_SCY_15 \
-					| OR_GPCM_TRLX_SET \
-					| OR_GPCM_EHTR_SET \
-					| OR_GPCM_EAD)
-					/* 0xFFFFE9F7 */
+
 
 /*
  * Windows to access PIB via local bus
@@ -237,45 +138,16 @@
 					/* PIB window base 0xF8008000 */
 #define CONFIG_SYS_PIB_BASE		0xF8008000
 #define CONFIG_SYS_PIB_WINDOW_SIZE	(32 * 1024)
-#define CONFIG_SYS_LBLAWBAR3_PRELIM	CONFIG_SYS_PIB_BASE
-#define CONFIG_SYS_LBLAWAR3_PRELIM	(LBLAWAR_EN | LBLAWAR_64KB)
 
 /*
  * CS2 on Local Bus, to PIB
  */
-#define CONFIG_SYS_BR2_PRELIM	(CONFIG_SYS_PIB_BASE \
-				| BR_PS_8 \
-				| BR_MS_GPCM \
-				| BR_V)
-				/* 0xF8008801 */
-#define CONFIG_SYS_OR2_PRELIM	(P2SZ_TO_AM(CONFIG_SYS_PIB_WINDOW_SIZE) \
-				| OR_GPCM_XAM \
-				| OR_GPCM_CSNT \
-				| OR_GPCM_XACS \
-				| OR_GPCM_SCY_15 \
-				| OR_GPCM_TRLX_SET \
-				| OR_GPCM_EHTR_SET \
-				| OR_GPCM_EAD)
-				/* 0xffffe9f7 */
+
 
 /*
  * CS3 on Local Bus, to PIB
  */
-#define CONFIG_SYS_BR3_PRELIM	((CONFIG_SYS_PIB_BASE + \
-					CONFIG_SYS_PIB_WINDOW_SIZE) \
-				| BR_PS_8 \
-				| BR_MS_GPCM \
-				| BR_V)
-				/* 0xF8010801 */
-#define CONFIG_SYS_OR3_PRELIM	(P2SZ_TO_AM(CONFIG_SYS_PIB_WINDOW_SIZE) \
-				| OR_GPCM_XAM \
-				| OR_GPCM_CSNT \
-				| OR_GPCM_XACS \
-				| OR_GPCM_SCY_15 \
-				| OR_GPCM_TRLX_SET \
-				| OR_GPCM_EHTR_SET \
-				| OR_GPCM_EAD)
-				/* 0xffffe9f7 */
+
 
 /*
  * Serial Port
@@ -404,116 +276,6 @@
 #define CONFIG_SYS_BOOTMAPSZ		(256 << 20)
 #define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
 
-/*
- * Core HID Setup
- */
-#define CONFIG_SYS_HID0_INIT	0x000000000
-#define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK | \
-				 HID0_ENABLE_INSTRUCTION_CACHE)
-#define CONFIG_SYS_HID2		HID2_HBE
-
-/*
- * MMU Setup
- */
-
-#define CONFIG_HIGH_BATS	1	/* High BATs supported */
-
-/* DDR: cache cacheable */
-#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
-
-/* IMMRBAR & PCI IO: cache-inhibit and guarded */
-#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_IMMR \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_IMMR \
-				| BATU_BL_4M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
-
-/* BCSR: cache-inhibit and guarded */
-#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_BCSR \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_BCSR \
-				| BATU_BL_128K \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT2L	CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
-
-/* FLASH: icache cacheable, but dcache-inhibit and guarded */
-#define CONFIG_SYS_IBAT3L	(CONFIG_SYS_FLASH_BASE \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT3U	(CONFIG_SYS_FLASH_BASE \
-				| BATU_BL_32M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT3L	(CONFIG_SYS_FLASH_BASE \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
-
-#define CONFIG_SYS_IBAT4L	(0)
-#define CONFIG_SYS_IBAT4U	(0)
-#define CONFIG_SYS_DBAT4L	CONFIG_SYS_IBAT4L
-#define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U
-
-/* Stack in dcache: cacheable, no memory coherence */
-#define CONFIG_SYS_IBAT5L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
-#define CONFIG_SYS_IBAT5U	(CONFIG_SYS_INIT_RAM_ADDR \
-				| BATU_BL_128K \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT5L	CONFIG_SYS_IBAT5L
-#define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
-
-#ifdef CONFIG_PCI
-/* PCI MEM space: cacheable */
-#define CONFIG_SYS_IBAT6L	(CONFIG_SYS_PCI1_MEM_PHYS \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT6U	(CONFIG_SYS_PCI1_MEM_PHYS \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
-#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
-/* PCI MMIO space: cache-inhibit and guarded */
-#define CONFIG_SYS_IBAT7L	(CONFIG_SYS_PCI1_MMIO_PHYS \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT7U	(CONFIG_SYS_PCI1_MMIO_PHYS \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
-#else
-#define CONFIG_SYS_IBAT6L	(0)
-#define CONFIG_SYS_IBAT6U	(0)
-#define CONFIG_SYS_IBAT7L	(0)
-#define CONFIG_SYS_IBAT7U	(0)
-#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
-#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
-#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
-#endif
-
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
 #endif
diff --git a/include/configs/MPC8349EMDS.h b/include/configs/MPC8349EMDS.h
index bda477cc16..7640d7610d 100644
--- a/include/configs/MPC8349EMDS.h
+++ b/include/configs/MPC8349EMDS.h
@@ -16,31 +16,6 @@
  * High Level Configuration Options
  */
 #define CONFIG_E300		1	/* E300 Family */
-#define CONFIG_MPC834x		1	/* MPC834x family */
-#define CONFIG_MPC8349		1	/* MPC8349 specific */
-
-#define CONFIG_PCI_66M
-#ifdef CONFIG_PCI_66M
-#define CONFIG_83XX_CLKIN	66000000	/* in Hz */
-#else
-#define CONFIG_83XX_CLKIN	33000000	/* in Hz */
-#endif
-
-#ifdef CONFIG_PCISLAVE
-#define CONFIG_83XX_PCICLK	66666666	/* in Hz */
-#endif /* CONFIG_PCISLAVE */
-
-#ifndef CONFIG_SYS_CLK_FREQ
-#ifdef CONFIG_PCI_66M
-#define CONFIG_SYS_CLK_FREQ	66000000
-#define HRCWL_CSB_TO_CLKIN	HRCWL_CSB_TO_CLKIN_4X1
-#else
-#define CONFIG_SYS_CLK_FREQ	33000000
-#define HRCWL_CSB_TO_CLKIN	HRCWL_CSB_TO_CLKIN_8X1
-#endif
-#endif
-
-#define CONFIG_SYS_IMMR		0xE0000000
 
 #undef CONFIG_SYS_DRAM_TEST		/* memory test, takes time */
 #define CONFIG_SYS_MEMTEST_START	0x00000000      /* memtest region */
@@ -77,9 +52,7 @@
  */
 #undef CONFIG_DDR_32BIT
 
-#define CONFIG_SYS_DDR_BASE	0x00000000	/* DDR is system memory*/
-#define CONFIG_SYS_SDRAM_BASE	CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_SDRAM_BASE	0x00000000	/* DDR is system memory*/
 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN \
 					| DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
 #undef  CONFIG_DDR_2T_TIMING
@@ -146,23 +119,6 @@
 #define CONFIG_SYS_FLASH_BASE		0xFE000000	/* start of FLASH   */
 #define CONFIG_SYS_FLASH_SIZE		32	/* max flash size in MB */
 
-#define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE \
-				| BR_PS_16	/* 16 bit port  */ \
-				| BR_MS_GPCM	/* MSEL = GPCM */ \
-				| BR_V)		/* valid */
-#define CONFIG_SYS_OR0_PRELIM	(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
-				| OR_UPM_XAM \
-				| OR_GPCM_CSNT \
-				| OR_GPCM_ACS_DIV2 \
-				| OR_GPCM_XACS \
-				| OR_GPCM_SCY_15 \
-				| OR_GPCM_TRLX_SET \
-				| OR_GPCM_EHTR_SET \
-				| OR_GPCM_EAD)
-
-					/* window base at flash base */
-#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_32MB)
 
 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
 #define CONFIG_SYS_MAX_FLASH_SECT	256	/* max sectors per device */
@@ -184,20 +140,7 @@
  */
 #define CONFIG_SYS_BCSR			0xE2400000
 					/* Access window base at BCSR base */
-#define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_BCSR
-#define CONFIG_SYS_LBLAWAR1_PRELIM	(LBLAWAR_EN | LBLAWAR_32KB)
-#define CONFIG_SYS_BR1_PRELIM		(CONFIG_SYS_BCSR \
-					| BR_PS_8 \
-					| BR_MS_GPCM \
-					| BR_V)
-					/* 0x00000801 */
-#define CONFIG_SYS_OR1_PRELIM		(OR_AM_32KB \
-					| OR_GPCM_XAM \
-					| OR_GPCM_CSNT \
-					| OR_GPCM_SCY_15 \
-					| OR_GPCM_TRLX_CLEAR \
-					| OR_GPCM_EHTR_CLEAR)
-					/* 0xFFFFE8F0 */
+
 
 #define CONFIG_SYS_INIT_RAM_LOCK	1
 #define CONFIG_SYS_INIT_RAM_ADDR	0xFD000000	/* Initial RAM addr */
@@ -211,92 +154,6 @@
 #define CONFIG_SYS_MALLOC_LEN	(256 * 1024)	/* Reserved for malloc */
 
 /*
- * Local Bus LCRR and LBCR regs
- *    LCRR:  DLL bypass, Clock divider is 4
- * External Local Bus rate is
- *    CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
- */
-#define CONFIG_SYS_LCRR_DBYP	LCRR_DBYP
-#define CONFIG_SYS_LCRR_CLKDIV	LCRR_CLKDIV_4
-#define CONFIG_SYS_LBC_LBCR	0x00000000
-
-/*
- * The MPC834xEA MDS for 834xE rev3.1 may not be assembled SDRAM memory.
- * if board has SRDAM on local bus, you can define CONFIG_SYS_LB_SDRAM
- */
-#undef CONFIG_SYS_LB_SDRAM
-
-#ifdef CONFIG_SYS_LB_SDRAM
-/* Local bus BR2, OR2 definition for SDRAM if soldered on the MDS board */
-/*
- * Base Register 2 and Option Register 2 configure SDRAM.
- * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000.
- *
- * For BR2, need:
- *    Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
- *    port-size = 32-bits = BR2[19:20] = 11
- *    no parity checking = BR2[21:22] = 00
- *    SDRAM for MSEL = BR2[24:26] = 011
- *    Valid = BR[31] = 1
- *
- * 0    4    8    12   16   20   24   28
- * 1111 0000 0000 0000 0001 1000 0110 0001 = F0001861
- */
-
-#define CONFIG_SYS_BR2_PRELIM		(CONFIG_SYS_LBC_SDRAM_BASE \
-					| BR_PS_32	/* 32-bit port */ \
-					| BR_MS_SDRAM	/* MSEL = SDRAM */ \
-					| BR_V)		/* Valid */
-					/* 0xF0001861 */
-#define CONFIG_SYS_LBLAWBAR2_PRELIM	CONFIG_SYS_LBC_SDRAM_BASE
-#define CONFIG_SYS_LBLAWAR2_PRELIM	(LBLAWAR_EN | LBLAWAR_64MB)
-
-/*
- * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
- *
- * For OR2, need:
- *    64MB mask for AM, OR2[0:7] = 1111 1100
- *                 XAM, OR2[17:18] = 11
- *    9 columns OR2[19-21] = 010
- *    13 rows   OR2[23-25] = 100
- *    EAD set for extra time OR[31] = 1
- *
- * 0    4    8    12   16   20   24   28
- * 1111 1100 0000 0000 0110 1001 0000 0001 = FC006901
- */
-
-#define CONFIG_SYS_OR2_PRELIM	(OR_AM_64MB \
-			| OR_SDRAM_XAM \
-			| ((9 - OR_SDRAM_MIN_COLS) << OR_SDRAM_COLS_SHIFT) \
-			| ((13 - OR_SDRAM_MIN_ROWS) << OR_SDRAM_ROWS_SHIFT) \
-			| OR_SDRAM_EAD)
-			/* 0xFC006901 */
-
-				/* LB sdram refresh timer, about 6us */
-#define CONFIG_SYS_LBC_LSRT	0x32000000
-				/* LB refresh timer prescal, 266MHz/32 */
-#define CONFIG_SYS_LBC_MRTPR	0x20000000
-
-#define CONFIG_SYS_LBC_LSDMR_COMMON    (LSDMR_RFEN	\
-				| LSDMR_BSMA1516	\
-				| LSDMR_RFCR8		\
-				| LSDMR_PRETOACT6	\
-				| LSDMR_ACTTORW3	\
-				| LSDMR_BL8		\
-				| LSDMR_WRC3		\
-				| LSDMR_CL3)
-
-/*
- * SDRAM Controller configuration sequence.
- */
-#define CONFIG_SYS_LBC_LSDMR_1	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_PCHALL)
-#define CONFIG_SYS_LBC_LSDMR_2	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH)
-#define CONFIG_SYS_LBC_LSDMR_3	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH)
-#define CONFIG_SYS_LBC_LSDMR_4	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW)
-#define CONFIG_SYS_LBC_LSDMR_5	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL)
-#endif
-
-/*
  * Serial Port
  */
 #define CONFIG_SYS_NS16550_SERIAL
@@ -363,13 +220,6 @@
 
 #if defined(CONFIG_PCI)
 
-#define PCI_ONE_PCI1
-#if defined(PCI_64BIT)
-#undef PCI_ALL_PCI1
-#undef PCI_TWO_PCI1
-#undef PCI_ONE_PCI1
-#endif
-
 #define CONFIG_83XX_PCI_STREAMING
 
 #undef CONFIG_EEPRO100
@@ -463,93 +313,9 @@
 
 #define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST  */
 
-#if 1 /*528/264*/
-#define CONFIG_SYS_HRCW_LOW (\
-	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
-	HRCWL_DDR_TO_SCB_CLK_1X1 |\
-	HRCWL_CSB_TO_CLKIN |\
-	HRCWL_VCO_1X2 |\
-	HRCWL_CORE_TO_CSB_2X1)
-#elif 0 /*396/132*/
-#define CONFIG_SYS_HRCW_LOW (\
-	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
-	HRCWL_DDR_TO_SCB_CLK_1X1 |\
-	HRCWL_CSB_TO_CLKIN |\
-	HRCWL_VCO_1X4 |\
-	HRCWL_CORE_TO_CSB_3X1)
-#elif 0 /*264/132*/
-#define CONFIG_SYS_HRCW_LOW (\
-	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
-	HRCWL_DDR_TO_SCB_CLK_1X1 |\
-	HRCWL_CSB_TO_CLKIN |\
-	HRCWL_VCO_1X4 |\
-	HRCWL_CORE_TO_CSB_2X1)
-#elif 0 /*132/132*/
-#define CONFIG_SYS_HRCW_LOW (\
-	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
-	HRCWL_DDR_TO_SCB_CLK_1X1 |\
-	HRCWL_CSB_TO_CLKIN |\
-	HRCWL_VCO_1X4 |\
-	HRCWL_CORE_TO_CSB_1X1)
-#elif 0 /*264/264 */
-#define CONFIG_SYS_HRCW_LOW (\
-	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
-	HRCWL_DDR_TO_SCB_CLK_1X1 |\
-	HRCWL_CSB_TO_CLKIN |\
-	HRCWL_VCO_1X4 |\
-	HRCWL_CORE_TO_CSB_1X1)
-#endif
-
-#ifdef CONFIG_PCISLAVE
-#define CONFIG_SYS_HRCW_HIGH (\
-	HRCWH_PCI_AGENT |\
-	HRCWH_64_BIT_PCI |\
-	HRCWH_PCI1_ARBITER_DISABLE |\
-	HRCWH_PCI2_ARBITER_DISABLE |\
-	HRCWH_CORE_ENABLE |\
-	HRCWH_FROM_0X00000100 |\
-	HRCWH_BOOTSEQ_DISABLE |\
-	HRCWH_SW_WATCHDOG_DISABLE |\
-	HRCWH_ROM_LOC_LOCAL_16BIT |\
-	HRCWH_TSEC1M_IN_GMII |\
-	HRCWH_TSEC2M_IN_GMII)
-#else
-#if defined(PCI_64BIT)
-#define CONFIG_SYS_HRCW_HIGH (\
-	HRCWH_PCI_HOST |\
-	HRCWH_64_BIT_PCI |\
-	HRCWH_PCI1_ARBITER_ENABLE |\
-	HRCWH_PCI2_ARBITER_DISABLE |\
-	HRCWH_CORE_ENABLE |\
-	HRCWH_FROM_0X00000100 |\
-	HRCWH_BOOTSEQ_DISABLE |\
-	HRCWH_SW_WATCHDOG_DISABLE |\
-	HRCWH_ROM_LOC_LOCAL_16BIT |\
-	HRCWH_TSEC1M_IN_GMII |\
-	HRCWH_TSEC2M_IN_GMII)
-#else
-#define CONFIG_SYS_HRCW_HIGH (\
-	HRCWH_PCI_HOST |\
-	HRCWH_32_BIT_PCI |\
-	HRCWH_PCI1_ARBITER_ENABLE |\
-	HRCWH_PCI2_ARBITER_ENABLE |\
-	HRCWH_CORE_ENABLE |\
-	HRCWH_FROM_0X00000100 |\
-	HRCWH_BOOTSEQ_DISABLE |\
-	HRCWH_SW_WATCHDOG_DISABLE |\
-	HRCWH_ROM_LOC_LOCAL_16BIT |\
-	HRCWH_TSEC1M_IN_GMII |\
-	HRCWH_TSEC2M_IN_GMII)
-#endif /* PCI_64BIT */
-#endif /* CONFIG_PCISLAVE */
-
 /*
  * System performance
  */
-#define CONFIG_SYS_ACR_PIPE_DEP	3	/* Arbiter pipeline depth (0-3) */
-#define CONFIG_SYS_ACR_RPTCNT	3	/* Arbiter repeat count (0-7) */
-#define CONFIG_SYS_SPCR_TSEC1EP	3	/* TSEC1 emergency priority (0-3) */
-#define CONFIG_SYS_SPCR_TSEC2EP	3	/* TSEC2 emergency priority (0-3) */
 #define CONFIG_SYS_SCCR_TSEC1CM	1	/* TSEC1 clock mode (0-3) */
 #define CONFIG_SYS_SCCR_TSEC2CM	1	/* TSEC2 & I2C0 clock mode (0-3) */
 
@@ -557,115 +323,10 @@
 #define CONFIG_SYS_SICRH 0
 #define CONFIG_SYS_SICRL SICRL_LDP_A
 
-#define CONFIG_SYS_HID0_INIT	0x000000000
-#define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK \
-				| HID0_ENABLE_INSTRUCTION_CACHE)
-
-/* #define CONFIG_SYS_HID0_FINAL	(\
-	HID0_ENABLE_INSTRUCTION_CACHE |\
-	HID0_ENABLE_M_BIT |\
-	HID0_ENABLE_ADDRESS_BROADCAST) */
-
-#define CONFIG_SYS_HID2 HID2_HBE
-#define CONFIG_HIGH_BATS	1	/* High BATs supported */
-
-/* DDR @ 0x00000000 */
-#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-
-/* PCI @ 0x80000000 */
 #ifdef CONFIG_PCI
 #define CONFIG_PCI_INDIRECT_BRIDGE
-#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_PCI1_MEM_BASE \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_PCI1_MEM_BASE \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_PCI1_MMIO_BASE \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_PCI1_MMIO_BASE \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#else
-#define CONFIG_SYS_IBAT1L	(0)
-#define CONFIG_SYS_IBAT1U	(0)
-#define CONFIG_SYS_IBAT2L	(0)
-#define CONFIG_SYS_IBAT2U	(0)
-#endif
-
-#ifdef CONFIG_MPC83XX_PCI2
-#define CONFIG_SYS_IBAT3L	(CONFIG_SYS_PCI2_MEM_BASE \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT3U	(CONFIG_SYS_PCI2_MEM_BASE \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_IBAT4L	(CONFIG_SYS_PCI2_MMIO_BASE \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT4U	(CONFIG_SYS_PCI2_MMIO_BASE \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#else
-#define CONFIG_SYS_IBAT3L	(0)
-#define CONFIG_SYS_IBAT3U	(0)
-#define CONFIG_SYS_IBAT4L	(0)
-#define CONFIG_SYS_IBAT4U	(0)
 #endif
 
-/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */
-#define CONFIG_SYS_IBAT5L	(CONFIG_SYS_IMMR \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT5U	(CONFIG_SYS_IMMR \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-
-/* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
-#define CONFIG_SYS_IBAT6L	(0xF0000000 \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT6U	(0xF0000000 \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-
-#define CONFIG_SYS_IBAT7L	(0)
-#define CONFIG_SYS_IBAT7U	(0)
-
-#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
-#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
-#define CONFIG_SYS_DBAT2L	CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
-#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
-#define CONFIG_SYS_DBAT4L	CONFIG_SYS_IBAT4L
-#define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U
-#define CONFIG_SYS_DBAT5L	CONFIG_SYS_IBAT5L
-#define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
-#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
-#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
-#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
-
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
 #endif
diff --git a/include/configs/MPC8349EMDS_SDRAM.h b/include/configs/MPC8349EMDS_SDRAM.h
new file mode 100644
index 0000000000..493f6df187
--- /dev/null
+++ b/include/configs/MPC8349EMDS_SDRAM.h
@@ -0,0 +1,455 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * (C) Copyright 2006-2010
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ */
+
+/*
+ * mpc8349emds board configuration file
+ *
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300		1	/* E300 Family */
+
+#undef CONFIG_SYS_DRAM_TEST		/* memory test, takes time */
+#define CONFIG_SYS_MEMTEST_START	0x00000000      /* memtest region */
+#define CONFIG_SYS_MEMTEST_END		0x00100000
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_DDR_ECC			/* support DDR ECC function */
+#define CONFIG_DDR_ECC_CMD		/* use DDR ECC user commands */
+#define CONFIG_SPD_EEPROM		/* use SPD EEPROM for DDR setup*/
+
+/*
+ * SYS_FSL_DDR2 is selected in Kconfig to use unified DDR driver
+ * unselect it to use old spd_sdram.c
+ */
+#define CONFIG_SYS_SPD_BUS_NUM	0
+#define SPD_EEPROM_ADDRESS1	0x52
+#define SPD_EEPROM_ADDRESS2	0x51
+#define CONFIG_DIMM_SLOTS_PER_CTLR	2
+#define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE	0xDeadBeef
+
+/*
+ * 32-bit data path mode.
+ *
+ * Please note that using this mode for devices with the real density of 64-bit
+ * effectively reduces the amount of available memory due to the effect of
+ * wrapping around while translating address to row/columns, for example in the
+ * 256MB module the upper 128MB get aliased with contents of the lower
+ * 128MB); normally this define should be used for devices with real 32-bit
+ * data path.
+ */
+#undef CONFIG_DDR_32BIT
+
+#define CONFIG_SYS_SDRAM_BASE	0x00000000	/* DDR is system memory*/
+#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN \
+					| DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
+#undef  CONFIG_DDR_2T_TIMING
+
+/*
+ * DDRCDR - DDR Control Driver Register
+ */
+#define CONFIG_SYS_DDRCDR_VALUE	0x80080001
+
+#if defined(CONFIG_SPD_EEPROM)
+/*
+ * Determine DDR configuration from I2C interface.
+ */
+#define SPD_EEPROM_ADDRESS	0x51		/* DDR DIMM */
+#else
+/*
+ * Manually set up DDR parameters
+ */
+#define CONFIG_SYS_DDR_SIZE		256		/* MB */
+#if defined(CONFIG_DDR_II)
+#define CONFIG_SYS_DDRCDR		0x80080001
+#define CONFIG_SYS_DDR_CS2_BNDS		0x0000000f
+#define CONFIG_SYS_DDR_CS2_CONFIG	0x80330102
+#define CONFIG_SYS_DDR_TIMING_0		0x00220802
+#define CONFIG_SYS_DDR_TIMING_1		0x38357322
+#define CONFIG_SYS_DDR_TIMING_2		0x2f9048c8
+#define CONFIG_SYS_DDR_TIMING_3		0x00000000
+#define CONFIG_SYS_DDR_CLK_CNTL		0x02000000
+#define CONFIG_SYS_DDR_MODE		0x47d00432
+#define CONFIG_SYS_DDR_MODE2		0x8000c000
+#define CONFIG_SYS_DDR_INTERVAL		0x03cf0080
+#define CONFIG_SYS_DDR_SDRAM_CFG	0x43000000
+#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000
+#else
+#define CONFIG_SYS_DDR_CS2_CONFIG	(CSCONFIG_EN \
+				| CSCONFIG_ROW_BIT_13 \
+				| CSCONFIG_COL_BIT_10)
+#define CONFIG_SYS_DDR_TIMING_1	0x36332321
+#define CONFIG_SYS_DDR_TIMING_2	0x00000800	/* P9-45,may need tuning */
+#define CONFIG_SYS_DDR_CONTROL	0xc2000000	/* unbuffered,no DYN_PWR */
+#define CONFIG_SYS_DDR_INTERVAL	0x04060100	/* autocharge,no open page */
+
+#if defined(CONFIG_DDR_32BIT)
+/* set burst length to 8 for 32-bit data path */
+				/* DLL,normal,seq,4/2.5, 8 burst len */
+#define CONFIG_SYS_DDR_MODE	0x00000023
+#else
+/* the default burst length is 4 - for 64-bit data path */
+				/* DLL,normal,seq,4/2.5, 4 burst len */
+#define CONFIG_SYS_DDR_MODE	0x00000022
+#endif
+#endif
+#endif
+
+/*
+ * SDRAM on the Local Bus
+ */
+#define CONFIG_SYS_LBC_SDRAM_BASE	0xF0000000	/* Localbus SDRAM */
+#define CONFIG_SYS_LBC_SDRAM_SIZE	64		/* LBC SDRAM is 64MB */
+
+/*
+ * FLASH on the Local Bus
+ */
+#define CONFIG_SYS_FLASH_BASE		0xFE000000	/* start of FLASH   */
+#define CONFIG_SYS_FLASH_SIZE		32	/* max flash size in MB */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max sectors per device */
+
+#undef CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
+
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_RAMBOOT
+#else
+#undef  CONFIG_SYS_RAMBOOT
+#endif
+
+/*
+ * BCSR register on local bus 32KB, 8-bit wide for MDS config reg
+ */
+#define CONFIG_SYS_BCSR			0xE2400000
+					/* Access window base at BCSR base */
+#define CONFIG_SYS_INIT_RAM_LOCK	1
+#define CONFIG_SYS_INIT_RAM_ADDR	0xFD000000	/* Initial RAM addr */
+#define CONFIG_SYS_INIT_RAM_SIZE	0x1000	/* Size of used area in RAM*/
+
+#define CONFIG_SYS_GBL_DATA_OFFSET	\
+			(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN	(512 * 1024)	/* Reserve 512 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN	(256 * 1024)	/* Reserved for malloc */
+
+/*
+ * The MPC834xEA MDS for 834xE rev3.1 may not be assembled SDRAM memory.
+ */
+
+/* Local bus BR2, OR2 definition for SDRAM if soldered on the MDS board */
+/*
+ * Base Register 2 and Option Register 2 configure SDRAM.
+ * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000.
+ *
+ * For BR2, need:
+ *    Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
+ *    port-size = 32-bits = BR2[19:20] = 11
+ *    no parity checking = BR2[21:22] = 00
+ *    SDRAM for MSEL = BR2[24:26] = 011
+ *    Valid = BR[31] = 1
+ *
+ * 0    4    8    12   16   20   24   28
+ * 1111 0000 0000 0000 0001 1000 0110 0001 = F0001861
+ */
+
+/*
+ * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
+ *
+ * For OR2, need:
+ *    64MB mask for AM, OR2[0:7] = 1111 1100
+ *                 XAM, OR2[17:18] = 11
+ *    9 columns OR2[19-21] = 010
+ *    13 rows   OR2[23-25] = 100
+ *    EAD set for extra time OR[31] = 1
+ *
+ * 0    4    8    12   16   20   24   28
+ * 1111 1100 0000 0000 0110 1001 0000 0001 = FC006901
+ */
+
+
+				/* LB sdram refresh timer, about 6us */
+#define CONFIG_SYS_LBC_LSRT	0x32000000
+				/* LB refresh timer prescal, 266MHz/32 */
+#define CONFIG_SYS_LBC_MRTPR	0x20000000
+
+#define CONFIG_SYS_LBC_LSDMR_COMMON    (LSDMR_RFEN	\
+				| LSDMR_BSMA1516	\
+				| LSDMR_RFCR8		\
+				| LSDMR_PRETOACT6	\
+				| LSDMR_ACTTORW3	\
+				| LSDMR_BL8		\
+				| LSDMR_WRC3		\
+				| LSDMR_CL3)
+
+/*
+ * SDRAM Controller configuration sequence.
+ */
+#define CONFIG_SYS_LBC_LSDMR_1	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_PCHALL)
+#define CONFIG_SYS_LBC_LSDMR_2	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH)
+#define CONFIG_SYS_LBC_LSDMR_3	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH)
+#define CONFIG_SYS_LBC_LSDMR_4	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW)
+#define CONFIG_SYS_LBC_LSDMR_5	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL)
+
+/*
+ * Serial Port
+ */
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE    1
+#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
+
+#define CONFIG_SYS_BAUDRATE_TABLE  \
+		{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+
+#define CONFIG_SYS_NS16550_COM1        (CONFIG_SYS_IMMR+0x4500)
+#define CONFIG_SYS_NS16550_COM2        (CONFIG_SYS_IMMR+0x4600)
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED	400000
+#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED	400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
+#define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x69} }
+
+/* SPI */
+#undef CONFIG_SOFT_SPI			/* SPI bit-banged */
+
+/* GPIOs.  Used as SPI chip selects */
+#define CONFIG_SYS_GPIO1_PRELIM
+#define CONFIG_SYS_GPIO1_DIR		0xC0000000  /* SPI CS on 0, LED on 1 */
+#define CONFIG_SYS_GPIO1_DAT		0xC0000000  /* Both are active LOW */
+
+/* TSEC */
+#define CONFIG_SYS_TSEC1_OFFSET 0x24000
+#define CONFIG_SYS_TSEC1	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
+#define CONFIG_SYS_TSEC2_OFFSET 0x25000
+#define CONFIG_SYS_TSEC2	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
+
+/* USB */
+#define CONFIG_SYS_USE_MPC834XSYS_USB_PHY	1 /* Use SYS board PHY */
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CONFIG_SYS_PCI1_MEM_BASE	0x80000000
+#define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BASE
+#define CONFIG_SYS_PCI1_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCI1_MMIO_BASE	0x90000000
+#define CONFIG_SYS_PCI1_MMIO_PHYS	CONFIG_SYS_PCI1_MMIO_BASE
+#define CONFIG_SYS_PCI1_MMIO_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCI1_IO_BASE		0x00000000
+#define CONFIG_SYS_PCI1_IO_PHYS		0xE2000000
+#define CONFIG_SYS_PCI1_IO_SIZE		0x00100000	/* 1M */
+
+#define CONFIG_SYS_PCI2_MEM_BASE	0xA0000000
+#define CONFIG_SYS_PCI2_MEM_PHYS	CONFIG_SYS_PCI2_MEM_BASE
+#define CONFIG_SYS_PCI2_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCI2_MMIO_BASE	0xB0000000
+#define CONFIG_SYS_PCI2_MMIO_PHYS	CONFIG_SYS_PCI2_MMIO_BASE
+#define CONFIG_SYS_PCI2_MMIO_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCI2_IO_BASE		0x00000000
+#define CONFIG_SYS_PCI2_IO_PHYS		0xE2100000
+#define CONFIG_SYS_PCI2_IO_SIZE		0x00100000	/* 1M */
+
+#if defined(CONFIG_PCI)
+
+#define CONFIG_83XX_PCI_STREAMING
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_TULIP
+
+#if !defined(CONFIG_PCI_PNP)
+	#define PCI_ENET0_IOADDR	0xFIXME
+	#define PCI_ENET0_MEMADDR	0xFIXME
+	#define PCI_IDSEL_NUMBER	0x0c	/* slot0->3(IDSEL)=12->15 */
+#endif
+
+#undef CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957  /* Freescale */
+
+#endif	/* CONFIG_PCI */
+
+/*
+ * TSEC configuration
+ */
+
+#if defined(CONFIG_TSEC_ENET)
+
+#define CONFIG_GMII		1	/* MII PHY management */
+#define CONFIG_TSEC1		1
+#define CONFIG_TSEC1_NAME	"TSEC0"
+#define CONFIG_TSEC2		1
+#define CONFIG_TSEC2_NAME	"TSEC1"
+#define TSEC1_PHY_ADDR		0
+#define TSEC2_PHY_ADDR		1
+#define TSEC1_PHYIDX		0
+#define TSEC2_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
+
+/* Options are: TSEC[0-1] */
+#define CONFIG_ETHPRIME		"TSEC0"
+
+#endif	/* CONFIG_TSEC_ENET */
+
+/*
+ * Configure on-board RTC
+ */
+#define CONFIG_RTC_DS1374		/* use ds1374 rtc via i2c */
+#define CONFIG_SYS_I2C_RTC_ADDR	0x68	/* at address 0x68 */
+
+/*
+ * Environment
+ */
+#ifndef CONFIG_SYS_RAMBOOT
+	#define CONFIG_ENV_ADDR		\
+			(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
+	#define CONFIG_ENV_SECT_SIZE	0x20000	/* 128K(one sector) for env */
+	#define CONFIG_ENV_SIZE		0x2000
+
+/* Address and size of Redundant Environment Sector	*/
+#define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
+
+#else
+	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
+	#define CONFIG_ENV_SIZE		0x2000
+#endif
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+
+/*
+ * Command line configuration.
+ */
+
+#undef CONFIG_WATCHDOG			/* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 256 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+				/* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTMAPSZ	(256 << 20)
+#define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
+
+#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST  */
+
+/*
+ * System performance
+ */
+#define CONFIG_SYS_SPCR_TSEC1EP	3	/* TSEC1 emergency priority (0-3) */
+#define CONFIG_SYS_SPCR_TSEC2EP	3	/* TSEC2 emergency priority (0-3) */
+#define CONFIG_SYS_SCCR_TSEC1CM	1	/* TSEC1 clock mode (0-3) */
+#define CONFIG_SYS_SCCR_TSEC2CM	1	/* TSEC2 & I2C0 clock mode (0-3) */
+
+/* System IO Config */
+#define CONFIG_SYS_SICRH 0
+#define CONFIG_SYS_SICRL SICRL_LDP_A
+
+#ifdef CONFIG_PCI
+#define CONFIG_PCI_INDIRECT_BRIDGE
+#endif
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
+#endif
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_OVERWRITE
+
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH1
+#define CONFIG_HAS_ETH0
+#endif
+
+#define CONFIG_HOSTNAME		"mpc8349emds"
+#define CONFIG_ROOTPATH		"/nfsroot/rootfs"
+#define CONFIG_BOOTFILE		"uImage"
+
+#define CONFIG_LOADADDR	800000	/* default location for tftp and bootm */
+
+#define CONFIG_PREBOOT	"echo;"	\
+	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
+	"echo"
+
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	"netdev=eth0\0"							\
+	"hostname=mpc8349emds\0"					\
+	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
+		"nfsroot=${serverip}:${rootpath}\0"			\
+	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
+	"addip=setenv bootargs ${bootargs} "				\
+		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
+		":${hostname}:${netdev}:off panic=1\0"			\
+	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
+	"flash_nfs=run nfsargs addip addtty;"				\
+		"bootm ${kernel_addr}\0"				\
+	"flash_self=run ramargs addip addtty;"				\
+		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
+	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"	\
+		"bootm\0"						\
+	"load=tftp 100000 /tftpboot/mpc8349emds/u-boot.bin\0"		\
+	"update=protect off fe000000 fe03ffff; "			\
+		"era fe000000 fe03ffff; cp.b 100000 fe000000 ${filesize}\0"\
+	"upd=run load update\0"						\
+	"fdtaddr=780000\0"						\
+	"fdtfile=mpc834x_mds.dtb\0"					\
+	""
+
+#define CONFIG_NFSBOOTCOMMAND						\
+	"setenv bootargs root=/dev/nfs rw "				\
+		"nfsroot=$serverip:$rootpath "				\
+		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"	\
+							"$netdev:off "	\
+		"console=$consoledev,$baudrate $othbootargs;"		\
+	"tftp $loadaddr $bootfile;"					\
+	"tftp $fdtaddr $fdtfile;"					\
+	"bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND						\
+	"setenv bootargs root=/dev/ram rw "				\
+		"console=$consoledev,$baudrate $othbootargs;"		\
+	"tftp $ramdiskaddr $ramdiskfile;"				\
+	"tftp $loadaddr $bootfile;"					\
+	"tftp $fdtaddr $fdtfile;"					\
+	"bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND	"run flash_self"
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/MPC8349ITX.h b/include/configs/MPC8349ITX.h
index 111023b7be..a3f704c73b 100644
--- a/include/configs/MPC8349ITX.h
+++ b/include/configs/MPC8349ITX.h
@@ -39,25 +39,13 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-#if (CONFIG_SYS_TEXT_BASE == 0xFE000000)
-#define CONFIG_SYS_LOWBOOT
-#endif
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_MPC834x		/* MPC834x family (8343, 8347, 8349) */
-#define CONFIG_MPC8349		/* MPC8349 specific */
-
-#define CONFIG_SYS_IMMR	0xE0000000	/* The IMMR is relocated to here */
-
 #define CONFIG_MISC_INIT_F
 
 /*
  * On-board devices
  */
 
-#ifdef CONFIG_MPC8349ITX
+#ifdef CONFIG_TARGET_MPC8349ITX
 /* The CF card interface on the back of the board */
 #define CONFIG_COMPACT_FLASH
 #define CONFIG_VSC7385_ENET	/* VSC7385 ethernet support */
@@ -154,9 +142,7 @@
 /*
  * DDR Setup
  */
-#define CONFIG_SYS_DDR_BASE		0x00000000 /* DDR is system memory*/
-#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_SDRAM_BASE		0x00000000 /* DDR is system memory*/
 #define CONFIG_SYS_83XX_DDR_USES_CS0
 #define CONFIG_SYS_MEMTEST_START	0x1000	/* memtest region */
 #define CONFIG_SYS_MEMTEST_END		0x2000
@@ -218,23 +204,6 @@ boards, we say we have two, but don't display a message if we find only one. */
  * BRx, ORx, LBLAWBARx, and LBLAWARx
  */
 
-/* Flash */
-
-#define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE \
-				| BR_PS_16 \
-				| BR_MS_GPCM \
-				| BR_V)
-#define CONFIG_SYS_OR0_PRELIM	(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
-				| OR_UPM_XAM \
-				| OR_GPCM_CSNT \
-				| OR_GPCM_ACS_DIV2 \
-				| OR_GPCM_XACS \
-				| OR_GPCM_SCY_15 \
-				| OR_GPCM_TRLX_SET \
-				| OR_GPCM_EHTR_SET \
-				| OR_GPCM_EAD)
-#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_16MB)
 
 /* Vitesse 7385 */
 
@@ -242,39 +211,12 @@ boards, we say we have two, but don't display a message if we find only one. */
 
 #ifdef CONFIG_VSC7385_ENET
 
-#define CONFIG_SYS_BR1_PRELIM	(CONFIG_SYS_VSC7385_BASE \
-				| BR_PS_8 \
-				| BR_MS_GPCM \
-				| BR_V)
-#define CONFIG_SYS_OR1_PRELIM	(OR_AM_128KB \
-				| OR_GPCM_CSNT \
-				| OR_GPCM_XACS \
-				| OR_GPCM_SCY_15 \
-				| OR_GPCM_SETA \
-				| OR_GPCM_TRLX_SET \
-				| OR_GPCM_EHTR_SET \
-				| OR_GPCM_EAD)
-
-#define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_VSC7385_BASE
-#define CONFIG_SYS_LBLAWAR1_PRELIM	(LBLAWAR_EN | LBLAWAR_128KB)
 
 #endif
 
-/* LED */
 
 #define CONFIG_SYS_LED_BASE	0xF9000000
-#define CONFIG_SYS_BR2_PRELIM	(CONFIG_SYS_LED_BASE \
-				| BR_PS_8 \
-				| BR_MS_GPCM \
-				| BR_V)
-#define CONFIG_SYS_OR2_PRELIM	(OR_AM_2MB \
-				| OR_GPCM_CSNT \
-				| OR_GPCM_ACS_DIV2 \
-				| OR_GPCM_XACS \
-				| OR_GPCM_SCY_9 \
-				| OR_GPCM_TRLX_SET \
-				| OR_GPCM_EHTR_SET \
-				| OR_GPCM_EAD)
+
 
 /* Compact Flash */
 
@@ -282,14 +224,6 @@ boards, we say we have two, but don't display a message if we find only one. */
 
 #define CONFIG_SYS_CF_BASE	0xF0000000
 
-#define CONFIG_SYS_BR3_PRELIM	(CONFIG_SYS_CF_BASE \
-				| BR_PS_16 \
-				| BR_MS_UPMA \
-				| BR_V)
-#define CONFIG_SYS_OR3_PRELIM	(OR_UPM_AM | OR_UPM_BI)
-
-#define CONFIG_SYS_LBLAWBAR3_PRELIM	CONFIG_SYS_CF_BASE
-#define CONFIG_SYS_LBLAWAR3_PRELIM	(LBLAWAR_EN | LBLAWAR_64KB)
 
 #endif
 
@@ -317,21 +251,6 @@ boards, we say we have two, but don't display a message if we find only one. */
 #define CONFIG_SYS_MALLOC_LEN	(256 * 1024) /* Reserved for malloc */
 
 /*
- * Local Bus LCRR and LBCR regs
- *    LCRR:  DLL bypass, Clock divider is 4
- * External Local Bus rate is
- *    CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
- */
-#define CONFIG_SYS_LCRR_DBYP	LCRR_DBYP
-#define CONFIG_SYS_LCRR_CLKDIV	LCRR_CLKDIV_4
-#define CONFIG_SYS_LBC_LBCR	0x00000000
-
-				/* LB sdram refresh timer, about 6us */
-#define CONFIG_SYS_LBC_LSRT	0x32000000
-				/* LB refresh timer prescal, 266MHz/32*/
-#define CONFIG_SYS_LBC_MRTPR	0x20000000
-
-/*
  * Serial Port
  */
 #define CONFIG_SYS_NS16550_SERIAL
@@ -394,13 +313,6 @@ boards, we say we have two, but don't display a message if we find only one. */
 
 #endif
 
-#define CONFIG_PCI_66M
-#ifdef CONFIG_PCI_66M
-#define CONFIG_83XX_CLKIN	66666666	/* in Hz */
-#else
-#define CONFIG_83XX_CLKIN	33333333	/* in Hz */
-#endif
-
 /* TSEC */
 
 #ifdef CONFIG_TSEC_ENET
@@ -471,48 +383,9 @@ boards, we say we have two, but don't display a message if we find only one. */
 #define CONFIG_SYS_BOOTMAPSZ	(256 << 20)
 #define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
 
-#define CONFIG_SYS_HRCW_LOW (\
-	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
-	HRCWL_DDR_TO_SCB_CLK_1X1 |\
-	HRCWL_CSB_TO_CLKIN_4X1 |\
-	HRCWL_VCO_1X2 |\
-	HRCWL_CORE_TO_CSB_2X1)
-
-#ifdef CONFIG_SYS_LOWBOOT
-#define CONFIG_SYS_HRCW_HIGH (\
-	HRCWH_PCI_HOST |\
-	HRCWH_32_BIT_PCI |\
-	HRCWH_PCI1_ARBITER_ENABLE |\
-	HRCWH_PCI2_ARBITER_ENABLE |\
-	HRCWH_CORE_ENABLE |\
-	HRCWH_FROM_0X00000100 |\
-	HRCWH_BOOTSEQ_DISABLE |\
-	HRCWH_SW_WATCHDOG_DISABLE |\
-	HRCWH_ROM_LOC_LOCAL_16BIT |\
-	HRCWH_TSEC1M_IN_GMII |\
-	HRCWH_TSEC2M_IN_GMII)
-#else
-#define CONFIG_SYS_HRCW_HIGH (\
-	HRCWH_PCI_HOST |\
-	HRCWH_32_BIT_PCI |\
-	HRCWH_PCI1_ARBITER_ENABLE |\
-	HRCWH_PCI2_ARBITER_ENABLE |\
-	HRCWH_CORE_ENABLE |\
-	HRCWH_FROM_0XFFF00100 |\
-	HRCWH_BOOTSEQ_DISABLE |\
-	HRCWH_SW_WATCHDOG_DISABLE |\
-	HRCWH_ROM_LOC_LOCAL_16BIT |\
-	HRCWH_TSEC1M_IN_GMII |\
-	HRCWH_TSEC2M_IN_GMII)
-#endif
-
 /*
  * System performance
  */
-#define CONFIG_SYS_ACR_PIPE_DEP	3	/* Arbiter pipeline depth (0-3) */
-#define CONFIG_SYS_ACR_RPTCNT	3	/* Arbiter repeat count (0-7) */
-#define CONFIG_SYS_SPCR_TSEC1EP	3	/* TSEC1 emergency priority (0-3) */
-#define CONFIG_SYS_SPCR_TSEC2EP	3	/* TSEC2 emergency priority (0-3) */
 #define CONFIG_SYS_SCCR_TSEC1CM	1	/* TSEC1 clock mode (0-3) */
 #define CONFIG_SYS_SCCR_TSEC2CM	1	/* TSEC2 & I2C0 clock mode (0-3) */
 #define CONFIG_SYS_SCCR_USBMPHCM 3	/* USB MPH controller's clock */
@@ -526,108 +399,6 @@ boards, we say we have two, but don't display a message if we find only one. */
 				/* USB DR as device + USB MPH as host */
 #define CONFIG_SYS_SICRL	(SICRL_LDP_A | SICRL_USB1)
 
-#define CONFIG_SYS_HID0_INIT	0x00000000
-#define CONFIG_SYS_HID0_FINAL	HID0_ENABLE_INSTRUCTION_CACHE
-
-#define CONFIG_SYS_HID2	HID2_HBE
-#define CONFIG_HIGH_BATS	1	/* High BATs supported */
-
-/* DDR  */
-#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-
-/* PCI  */
-#ifdef CONFIG_PCI
-#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_PCI1_MEM_BASE \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_PCI1_MEM_BASE \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_PCI1_MMIO_BASE \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_PCI1_MMIO_BASE \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#else
-#define CONFIG_SYS_IBAT1L	0
-#define CONFIG_SYS_IBAT1U	0
-#define CONFIG_SYS_IBAT2L	0
-#define CONFIG_SYS_IBAT2U	0
-#endif
-
-#ifdef CONFIG_MPC83XX_PCI2
-#define CONFIG_SYS_IBAT3L	(CONFIG_SYS_PCI2_MEM_BASE \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT3U	(CONFIG_SYS_PCI2_MEM_BASE \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_IBAT4L	(CONFIG_SYS_PCI2_MMIO_BASE \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT4U	(CONFIG_SYS_PCI2_MMIO_BASE \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#else
-#define CONFIG_SYS_IBAT3L	0
-#define CONFIG_SYS_IBAT3U	0
-#define CONFIG_SYS_IBAT4L	0
-#define CONFIG_SYS_IBAT4U	0
-#endif
-
-/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */
-#define CONFIG_SYS_IBAT5L	(CONFIG_SYS_IMMR \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT5U	(CONFIG_SYS_IMMR \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-
-/* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
-#define CONFIG_SYS_IBAT6L	(0xF0000000 \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT6U	(0xF0000000 \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-
-#define CONFIG_SYS_IBAT7L	0
-#define CONFIG_SYS_IBAT7U	0
-
-#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
-#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
-#define CONFIG_SYS_DBAT2L	CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
-#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
-#define CONFIG_SYS_DBAT4L	CONFIG_SYS_IBAT4L
-#define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U
-#define CONFIG_SYS_DBAT5L	CONFIG_SYS_IBAT5L
-#define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
-#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
-#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
-#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
-
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
 #endif
@@ -645,7 +416,7 @@ boards, we say we have two, but don't display a message if we find only one. */
 				/* U-Boot image on TFTP server */
 #define CONFIG_UBOOTPATH	"u-boot.bin"
 
-#ifdef CONFIG_MPC8349ITX
+#ifdef CONFIG_TARGET_MPC8349ITX
 #define CONFIG_FDTFILE		"mpc8349emitx.dtb"
 #else
 #define CONFIG_FDTFILE		"mpc8349emitxgp.dtb"
diff --git a/include/configs/MPC837XEMDS.h b/include/configs/MPC837XEMDS.h
index 50f6df5844..724f8afb76 100644
--- a/include/configs/MPC837XEMDS.h
+++ b/include/configs/MPC837XEMDS.h
@@ -11,70 +11,6 @@
  * High Level Configuration Options
  */
 #define CONFIG_E300		1 /* E300 family */
-#define CONFIG_MPC837x		1 /* MPC837x CPU specific */
-#define CONFIG_MPC837XEMDS	1 /* MPC837XEMDS board specific */
-
-/*
- * System Clock Setup
- */
-#ifdef CONFIG_PCISLAVE
-#define CONFIG_83XX_PCICLK	66000000 /* in HZ */
-#else
-#define CONFIG_83XX_CLKIN	66000000 /* in Hz */
-#endif
-
-#ifndef CONFIG_SYS_CLK_FREQ
-#define CONFIG_SYS_CLK_FREQ	66000000
-#endif
-
-/*
- * Hardware Reset Configuration Word
- * if CLKIN is 66MHz, then
- * CSB = 396MHz, CORE = 594MHz, DDRC = 396MHz, LBC = 396MHz
- */
-#define CONFIG_SYS_HRCW_LOW (\
-	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
-	HRCWL_DDR_TO_SCB_CLK_1X1 |\
-	HRCWL_SVCOD_DIV_2 |\
-	HRCWL_CSB_TO_CLKIN_6X1 |\
-	HRCWL_CORE_TO_CSB_1_5X1)
-
-#ifdef CONFIG_PCISLAVE
-#define CONFIG_SYS_HRCW_HIGH (\
-	HRCWH_PCI_AGENT |\
-	HRCWH_PCI1_ARBITER_DISABLE |\
-	HRCWH_CORE_ENABLE |\
-	HRCWH_FROM_0XFFF00100 |\
-	HRCWH_BOOTSEQ_DISABLE |\
-	HRCWH_SW_WATCHDOG_DISABLE |\
-	HRCWH_ROM_LOC_LOCAL_16BIT |\
-	HRCWH_RL_EXT_LEGACY |\
-	HRCWH_TSEC1M_IN_RGMII |\
-	HRCWH_TSEC2M_IN_RGMII |\
-	HRCWH_BIG_ENDIAN |\
-	HRCWH_LDP_CLEAR)
-#else
-#define CONFIG_SYS_HRCW_HIGH (\
-	HRCWH_PCI_HOST |\
-	HRCWH_PCI1_ARBITER_ENABLE |\
-	HRCWH_CORE_ENABLE |\
-	HRCWH_FROM_0X00000100 |\
-	HRCWH_BOOTSEQ_DISABLE |\
-	HRCWH_SW_WATCHDOG_DISABLE |\
-	HRCWH_ROM_LOC_LOCAL_16BIT |\
-	HRCWH_RL_EXT_LEGACY |\
-	HRCWH_TSEC1M_IN_RGMII |\
-	HRCWH_TSEC2M_IN_RGMII |\
-	HRCWH_BIG_ENDIAN |\
-	HRCWH_LDP_CLEAR)
-#endif
-
-/* Arbiter Configuration Register */
-#define CONFIG_SYS_ACR_PIPE_DEP	3	/* Arbiter pipeline depth is 4 */
-#define CONFIG_SYS_ACR_RPTCNT	3	/* Arbiter repeat count is 4 */
-
-/* System Priority Control Register */
-#define CONFIG_SYS_SPCR_TSECEP	3 /* eTSEC1/2 emergency has highest priority */
 
 /*
  * IP blocks clock configuration
@@ -97,16 +33,9 @@
 #define CONFIG_HWCONFIG
 
 /*
- * IMMR new address
- */
-#define CONFIG_SYS_IMMR		0xE0000000
-
-/*
  * DDR Setup
  */
-#define CONFIG_SYS_DDR_BASE		0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_SDRAM_BASE		0x00000000 /* DDR is system memory */
 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
 #define CONFIG_SYS_83XX_DDR_USES_CS0
 #define CONFIG_SYS_DDRCDR_VALUE		(DDRCDR_DHC_EN \
@@ -205,12 +134,6 @@
 #define CONFIG_SYS_GBL_DATA_OFFSET	\
 			(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 
-/*
- * Local Bus Configuration & Clock Setup
- */
-#define CONFIG_SYS_LCRR_DBYP	LCRR_DBYP
-#define CONFIG_SYS_LCRR_CLKDIV	LCRR_CLKDIV_8
-#define CONFIG_SYS_LBC_LBCR		0x00000000
 #define CONFIG_FSL_ELBC		1
 
 /*
@@ -219,24 +142,6 @@
 #define CONFIG_SYS_FLASH_BASE	0xFE000000 /* FLASH base address */
 #define CONFIG_SYS_FLASH_SIZE	32 /* max FLASH size is 32M */
 
-					/* Window base at flash base */
-#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_32MB)
-
-#define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE \
-				| BR_PS_16	/* 16 bit port */ \
-				| BR_MS_GPCM	/* MSEL = GPCM */ \
-				| BR_V)		/* valid */
-#define CONFIG_SYS_OR0_PRELIM	(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
-				| OR_UPM_XAM \
-				| OR_GPCM_CSNT \
-				| OR_GPCM_ACS_DIV2 \
-				| OR_GPCM_XACS \
-				| OR_GPCM_SCY_15 \
-				| OR_GPCM_TRLX_SET \
-				| OR_GPCM_EHTR_SET \
-				| OR_GPCM_EAD)
-				/* 0xFE000FF7 */
 
 #define CONFIG_SYS_MAX_FLASH_BANKS	1 /* number of banks */
 #define CONFIG_SYS_MAX_FLASH_SECT	256 /* max sectors per device */
@@ -250,23 +155,6 @@
  */
 #define CONFIG_SYS_BCSR		0xF8000000
 					/* Access window base at BCSR base */
-#define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_BCSR
-#define CONFIG_SYS_LBLAWAR1_PRELIM	(LBLAWAR_EN | LBLAWAR_32KB)
-
-#define CONFIG_SYS_BR1_PRELIM	(CONFIG_SYS_BCSR \
-				| BR_PS_8 \
-				| BR_MS_GPCM \
-				| BR_V)
-				/* 0xF8000801 */
-#define CONFIG_SYS_OR1_PRELIM	(OR_AM_32KB \
-				| OR_GPCM_XAM \
-				| OR_GPCM_CSNT \
-				| OR_GPCM_XACS \
-				| OR_GPCM_SCY_15 \
-				| OR_GPCM_TRLX_SET \
-				| OR_GPCM_EHTR_SET \
-				| OR_GPCM_EAD)
-				/* 0xFFFFE9F7 */
 
 /*
  * NAND Flash on the Local Bus
@@ -275,23 +163,7 @@
 #define CONFIG_NAND_FSL_ELBC	1
 
 #define CONFIG_SYS_NAND_BASE	0xE0600000
-#define CONFIG_SYS_BR3_PRELIM	(CONFIG_SYS_NAND_BASE \
-				| BR_DECC_CHK_GEN	/* Use HW ECC */ \
-				| BR_PS_8		/* 8 bit port */ \
-				| BR_MS_FCM		/* MSEL = FCM */ \
-				| BR_V)			/* valid */
-#define CONFIG_SYS_OR3_PRELIM	(OR_AM_32KB \
-				| OR_FCM_BCTLD \
-				| OR_FCM_CST \
-				| OR_FCM_CHT \
-				| OR_FCM_SCY_1 \
-				| OR_FCM_RST \
-				| OR_FCM_TRLX \
-				| OR_FCM_EHTR)
-				/* 0xFFFF919E */
-
-#define CONFIG_SYS_LBLAWBAR3_PRELIM	CONFIG_SYS_NAND_BASE
-#define CONFIG_SYS_LBLAWAR3_PRELIM	(LBLAWAR_EN | LBLAWAR_32KB)
+
 
 /*
  * Serial Port
@@ -469,123 +341,6 @@ extern int board_pci_host_broken(void);
 #define CONFIG_SYS_BOOTMAPSZ	(256 << 20) /* Initial Memory map for Linux */
 #define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
 
-/*
- * Core HID Setup
- */
-#define CONFIG_SYS_HID0_INIT	0x000000000
-#define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK | \
-				 HID0_ENABLE_INSTRUCTION_CACHE)
-#define CONFIG_SYS_HID2		HID2_HBE
-
-/*
- * MMU Setup
- */
-#define CONFIG_HIGH_BATS	1	/* High BATs supported */
-
-/* DDR: cache cacheable */
-#define CONFIG_SYS_SDRAM_LOWER		CONFIG_SYS_SDRAM_BASE
-#define CONFIG_SYS_SDRAM_UPPER		(CONFIG_SYS_SDRAM_BASE + 0x10000000)
-
-#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_LOWER \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_LOWER \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
-
-#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_SDRAM_UPPER \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_SDRAM_UPPER \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
-
-/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
-#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_IMMR \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_IMMR \
-				| BATU_BL_8M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT2L	CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
-
-/* BCSR: cache-inhibit and guarded */
-#define CONFIG_SYS_IBAT3L	(CONFIG_SYS_BCSR \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT3U	(CONFIG_SYS_BCSR \
-				| BATU_BL_128K \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
-
-/* FLASH: icache cacheable, but dcache-inhibit and guarded */
-#define CONFIG_SYS_IBAT4L	(CONFIG_SYS_FLASH_BASE \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT4U	(CONFIG_SYS_FLASH_BASE \
-				| BATU_BL_32M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT4L	(CONFIG_SYS_FLASH_BASE \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U
-
-/* Stack in dcache: cacheable, no memory coherence */
-#define CONFIG_SYS_IBAT5L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
-#define CONFIG_SYS_IBAT5U	(CONFIG_SYS_INIT_RAM_ADDR \
-				| BATU_BL_128K \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT5L	CONFIG_SYS_IBAT5L
-#define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
-
-#ifdef CONFIG_PCI
-/* PCI MEM space: cacheable */
-#define CONFIG_SYS_IBAT6L	(CONFIG_SYS_PCI_MEM_PHYS \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT6U	(CONFIG_SYS_PCI_MEM_PHYS \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
-#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
-/* PCI MMIO space: cache-inhibit and guarded */
-#define CONFIG_SYS_IBAT7L	(CONFIG_SYS_PCI_MMIO_PHYS \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT7U	(CONFIG_SYS_PCI_MMIO_PHYS \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
-#else
-#define CONFIG_SYS_IBAT6L	(0)
-#define CONFIG_SYS_IBAT6U	(0)
-#define CONFIG_SYS_IBAT7L	(0)
-#define CONFIG_SYS_IBAT7U	(0)
-#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
-#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
-#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
-#endif
-
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
 #endif
diff --git a/include/configs/MPC837XERDB.h b/include/configs/MPC837XERDB.h
index 4ddd62ddbb..13a7682958 100644
--- a/include/configs/MPC837XERDB.h
+++ b/include/configs/MPC837XERDB.h
@@ -12,8 +12,6 @@
  * High Level Configuration Options
  */
 #define CONFIG_E300		1 /* E300 family */
-#define CONFIG_MPC837x		1 /* MPC837x CPU specific */
-#define CONFIG_MPC837XERDB	1
 
 #define CONFIG_HWCONFIG
 
@@ -22,70 +20,9 @@
  */
 #define CONFIG_VSC7385_ENET
 
-/*
- * System Clock Setup
- */
-#ifdef CONFIG_PCISLAVE
-#define CONFIG_83XX_PCICLK	66666667 /* in HZ */
-#else
-#define CONFIG_83XX_CLKIN	66666667 /* in Hz */
-#define CONFIG_PCIE
-#endif
-
-#ifndef CONFIG_SYS_CLK_FREQ
-#define CONFIG_SYS_CLK_FREQ	CONFIG_83XX_CLKIN
-#endif
-
-/*
- * Hardware Reset Configuration Word
- */
-#define CONFIG_SYS_HRCW_LOW (\
-	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
-	HRCWL_DDR_TO_SCB_CLK_1X1 |\
-	HRCWL_SVCOD_DIV_2 |\
-	HRCWL_CSB_TO_CLKIN_5X1 |\
-	HRCWL_CORE_TO_CSB_2X1)
-
-#ifdef CONFIG_PCISLAVE
-#define CONFIG_SYS_HRCW_HIGH (\
-	HRCWH_PCI_AGENT |\
-	HRCWH_PCI1_ARBITER_DISABLE |\
-	HRCWH_CORE_ENABLE |\
-	HRCWH_FROM_0XFFF00100 |\
-	HRCWH_BOOTSEQ_DISABLE |\
-	HRCWH_SW_WATCHDOG_DISABLE |\
-	HRCWH_ROM_LOC_LOCAL_16BIT |\
-	HRCWH_RL_EXT_LEGACY |\
-	HRCWH_TSEC1M_IN_RGMII |\
-	HRCWH_TSEC2M_IN_RGMII |\
-	HRCWH_BIG_ENDIAN |\
-	HRCWH_LDP_CLEAR)
-#else
-#define CONFIG_SYS_HRCW_HIGH (\
-	HRCWH_PCI_HOST |\
-	HRCWH_PCI1_ARBITER_ENABLE |\
-	HRCWH_CORE_ENABLE |\
-	HRCWH_FROM_0X00000100 |\
-	HRCWH_BOOTSEQ_DISABLE |\
-	HRCWH_SW_WATCHDOG_DISABLE |\
-	HRCWH_ROM_LOC_LOCAL_16BIT |\
-	HRCWH_RL_EXT_LEGACY |\
-	HRCWH_TSEC1M_IN_RGMII |\
-	HRCWH_TSEC2M_IN_RGMII |\
-	HRCWH_BIG_ENDIAN |\
-	HRCWH_LDP_CLEAR)
-#endif
-
 /* System performance - define the value i.e. CONFIG_SYS_XXX
 */
 
-/* Arbiter Configuration Register */
-#define CONFIG_SYS_ACR_PIPE_DEP	3	/* Arbiter pipeline depth (0-3) */
-#define CONFIG_SYS_ACR_RPTCNT	3	/* Arbiter repeat count (0-7) */
-
-/* System Priority Control Regsiter */
-#define CONFIG_SYS_SPCR_TSECEP	3	/* eTSEC1&2 emergency priority (0-3) */
-
 /* System Clock Configuration Register */
 #define CONFIG_SYS_SCCR_TSEC1CM	1		/* eTSEC1 clock mode (0-3) */
 #define CONFIG_SYS_SCCR_TSEC2CM	1		/* eTSEC2 clock mode (0-3) */
@@ -103,11 +40,6 @@
 #define CONFIG_SYS_OBIR		0x30100000
 
 /*
- * IMMR new address
- */
-#define CONFIG_SYS_IMMR		0xE0000000
-
-/*
  * Device configurations
  */
 
@@ -126,9 +58,7 @@
 /*
  * DDR Setup
  */
-#define CONFIG_SYS_DDR_BASE		0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_SDRAM_BASE		0x00000000 /* DDR is system memory */
 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	0x03000000
 #define CONFIG_SYS_83XX_DDR_USES_CS0
 
@@ -228,12 +158,6 @@
 #define CONFIG_SYS_GBL_DATA_OFFSET	\
 			(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 
-/*
- * Local Bus Configuration & Clock Setup
- */
-#define CONFIG_SYS_LCRR_DBYP	LCRR_DBYP
-#define CONFIG_SYS_LCRR_CLKDIV	LCRR_CLKDIV_8
-#define CONFIG_SYS_LBC_LBCR		0x00000000
 #define CONFIG_FSL_ELBC		1
 
 /*
@@ -244,20 +168,6 @@
 
 #define CONFIG_SYS_FLASH_EMPTY_INFO		/* display empty sectors */
 
-					/* Window base at flash base */
-#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM	0x80000016	/* 8 MB window size */
-
-#define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE \
-				| BR_PS_16	/* 16 bit port */ \
-				| BR_MS_GPCM	/* MSEL = GPCM */ \
-				| BR_V)		/* valid */
-#define CONFIG_SYS_OR0_PRELIM	(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
-				| OR_GPCM_XACS \
-				| OR_GPCM_SCY_9 \
-				| OR_GPCM_EHTR_SET \
-				| OR_GPCM_EAD)
-				/* 0xFF800191 */
 
 #define CONFIG_SYS_MAX_FLASH_BANKS	1 /* number of banks */
 #define CONFIG_SYS_MAX_FLASH_SECT	256 /* max sectors per device */
@@ -270,20 +180,7 @@
  * NAND Flash on the Local Bus
  */
 #define CONFIG_SYS_NAND_BASE	0xE0600000
-#define CONFIG_SYS_BR1_PRELIM	(CONFIG_SYS_NAND_BASE \
-				| BR_DECC_CHK_GEN	/* Use HW ECC */ \
-				| BR_PS_8		/* 8 bit port */ \
-				| BR_MS_FCM		/* MSEL = FCM */ \
-				| BR_V)			/* valid */
-#define CONFIG_SYS_OR1_PRELIM	(OR_AM_32KB \
-				| OR_FCM_CSCT \
-				| OR_FCM_CST \
-				| OR_FCM_CHT \
-				| OR_FCM_SCY_1 \
-				| OR_FCM_TRLX \
-				| OR_FCM_EHTR)
-#define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_NAND_BASE
-#define CONFIG_SYS_LBLAWAR1_PRELIM	(LBLAWAR_EN | LBLAWAR_32KB)
+
 
 /* Vitesse 7385 */
 
@@ -291,24 +188,6 @@
 
 #ifdef CONFIG_VSC7385_ENET
 
-#define CONFIG_SYS_BR2_PRELIM		(CONFIG_SYS_VSC7385_BASE \
-					| BR_PS_8 \
-					| BR_MS_GPCM \
-					| BR_V)
-					/* 0xF0000801 */
-#define CONFIG_SYS_OR2_PRELIM		(OR_AM_128KB \
-					| OR_GPCM_CSNT \
-					| OR_GPCM_XACS \
-					| OR_GPCM_SCY_15 \
-					| OR_GPCM_SETA \
-					| OR_GPCM_TRLX_SET \
-					| OR_GPCM_EHTR_SET \
-					| OR_GPCM_EAD)
-					/* 0xfffe09ff */
-
-					/* Access Base */
-#define CONFIG_SYS_LBLAWBAR2_PRELIM	CONFIG_SYS_VSC7385_BASE
-#define CONFIG_SYS_LBLAWAR2_PRELIM	(LBLAWAR_EN | LBLAWAR_128KB)
 
 #endif
 
@@ -483,124 +362,6 @@
 #define CONFIG_SYS_BOOTMAPSZ	(256 << 20) /* Initial Memory map for Linux */
 #define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
 
-/*
- * Core HID Setup
- */
-#define CONFIG_SYS_HID0_INIT	0x000000000
-#define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK \
-				| HID0_ENABLE_INSTRUCTION_CACHE)
-#define CONFIG_SYS_HID2		HID2_HBE
-
-/*
- * MMU Setup
- */
-
-#define CONFIG_HIGH_BATS	1	/* High BATs supported */
-
-/* DDR: cache cacheable */
-#define CONFIG_SYS_SDRAM_LOWER		CONFIG_SYS_SDRAM_BASE
-#define CONFIG_SYS_SDRAM_UPPER		(CONFIG_SYS_SDRAM_BASE + 0x10000000)
-
-#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_LOWER \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_LOWER \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
-
-#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_SDRAM_UPPER \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_SDRAM_UPPER \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
-
-/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
-#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_IMMR \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_IMMR \
-				| BATU_BL_8M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT2L	CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
-
-/* L2 Switch: cache-inhibit and guarded */
-#define CONFIG_SYS_IBAT3L	(CONFIG_SYS_VSC7385_BASE \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT3U	(CONFIG_SYS_VSC7385_BASE \
-				| BATU_BL_128K \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
-
-/* FLASH: icache cacheable, but dcache-inhibit and guarded */
-#define CONFIG_SYS_IBAT4L	(CONFIG_SYS_FLASH_BASE \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT4U	(CONFIG_SYS_FLASH_BASE \
-				| BATU_BL_32M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT4L	(CONFIG_SYS_FLASH_BASE \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U
-
-/* Stack in dcache: cacheable, no memory coherence */
-#define CONFIG_SYS_IBAT5L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
-#define CONFIG_SYS_IBAT5U	(CONFIG_SYS_INIT_RAM_ADDR \
-				| BATU_BL_128K \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT5L	CONFIG_SYS_IBAT5L
-#define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
-
-#ifdef CONFIG_PCI
-/* PCI MEM space: cacheable */
-#define CONFIG_SYS_IBAT6L	(CONFIG_SYS_PCI_MEM_PHYS \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT6U	(CONFIG_SYS_PCI_MEM_PHYS \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
-#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
-/* PCI MMIO space: cache-inhibit and guarded */
-#define CONFIG_SYS_IBAT7L	(CONFIG_SYS_PCI_MMIO_PHYS \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT7U	(CONFIG_SYS_PCI_MMIO_PHYS \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
-#else
-#define CONFIG_SYS_IBAT6L	(0)
-#define CONFIG_SYS_IBAT6U	(0)
-#define CONFIG_SYS_IBAT7L	(0)
-#define CONFIG_SYS_IBAT7U	(0)
-#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
-#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
-#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
-#endif
-
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
 #endif
diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h
index b534d4758b..04f55e3990 100644
--- a/include/configs/MPC8610HPCD.h
+++ b/include/configs/MPC8610HPCD.h
@@ -43,7 +43,6 @@
 #define CONFIG_INTERRUPTS		/* enable pci, srio, ddr interrupts */
 
 #define CONFIG_BAT_RW		1	/* Use common BAT rw code */
-#define CONFIG_HIGH_BATS	1	/* High BATs supported & enabled */
 #define CONFIG_ALTIVEC		1
 
 /*
diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h
index 9318b190ae..8c01891e26 100644
--- a/include/configs/MPC8641HPCN.h
+++ b/include/configs/MPC8641HPCN.h
@@ -45,7 +45,6 @@
 #define CONFIG_ENV_OVERWRITE
 
 #define CONFIG_BAT_RW		1	/* Use common BAT rw code */
-#define CONFIG_HIGH_BATS	1	/* High BATs supported and enabled */
 #define CONFIG_SYS_NUM_ADDR_MAP 8	/* Number of addr map slots = 8 dbats */
 
 #define CONFIG_ALTIVEC		1
diff --git a/include/configs/TQM834x.h b/include/configs/TQM834x.h
index 0942b872ac..0da34d05af 100644
--- a/include/configs/TQM834x.h
+++ b/include/configs/TQM834x.h
@@ -15,26 +15,6 @@
  * High Level Configuration Options
  */
 #define CONFIG_E300		1	/* E300 Family */
-#define CONFIG_MPC834x		1	/* MPC834x specific */
-#define CONFIG_MPC8349		1	/* MPC8349 specific */
-
-/* IMMR Base Address Register, use Freescale default: 0xff400000 */
-#define CONFIG_SYS_IMMR		0xff400000
-
-/* System clock. Primary input clock when in PCI host mode */
-#define CONFIG_83XX_CLKIN	66666000	/* 66,666 MHz */
-
-/*
- * Local Bus LCRR
- *    LCRR:  DLL bypass, Clock divider is 8
- *
- *    for CSB = 266 MHz it gives LCB clock frequency = 33 MHz
- *
- * External Local Bus rate is
- *    CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
- */
-#define CONFIG_SYS_LCRR_DBYP	LCRR_DBYP
-#define CONFIG_SYS_LCRR_CLKDIV	LCRR_CLKDIV_8
 
 /* board pre init: do not call, nothing to do */
 
@@ -44,9 +24,7 @@
  * DDR Setup
  */
 				/* DDR is system memory*/
-#define CONFIG_SYS_DDR_BASE	0x00000000
-#define CONFIG_SYS_SDRAM_BASE	CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_SDRAM_BASE	0x00000000
 #define DDR_CASLAT_25		/* CASLAT set to 2.5 */
 #undef CONFIG_DDR_ECC		/* only for ECC DDR module */
 #undef CONFIG_SPD_EEPROM	/* do not use SPD EEPROM for DDR setup */
@@ -81,43 +59,16 @@
 
 #define CONFIG_SYS_MAX_FLASH_SECT	512	/* max sectors per device */
 
-/* 32 bit device at 0x80000000 via GPCM (0x8000_1801) */
-#define CONFIG_SYS_BR0_PRELIM	((CONFIG_SYS_FLASH_BASE & BR_BA) \
-				| BR_MS_GPCM \
-				| BR_PS_32 \
-				| BR_V)
-
-/* FLASH timing (0x0000_0c54) */
-#define CONFIG_SYS_OR_TIMING_FLASH	(OR_GPCM_CSNT \
-					| OR_GPCM_ACS_DIV4 \
-					| OR_GPCM_SCY_5 \
-					| OR_GPCM_TRLX)
-
-#define CONFIG_SYS_PRELIM_OR_AM		OR_AM_1GB /* OR addr mask: 1 GiB */
-
-#define CONFIG_SYS_OR0_PRELIM		(CONFIG_SYS_PRELIM_OR_AM  \
-					| CONFIG_SYS_OR_TIMING_FLASH)
-
-#define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_1GB)
-
-					/* Window base at flash base */
-#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
 
 /* disable remaining mappings */
 #define CONFIG_SYS_BR1_PRELIM		0x00000000
 #define CONFIG_SYS_OR1_PRELIM		0x00000000
-#define CONFIG_SYS_LBLAWBAR1_PRELIM	0x00000000
-#define CONFIG_SYS_LBLAWAR1_PRELIM	0x00000000
 
 #define CONFIG_SYS_BR2_PRELIM		0x00000000
 #define CONFIG_SYS_OR2_PRELIM		0x00000000
-#define CONFIG_SYS_LBLAWBAR2_PRELIM	0x00000000
-#define CONFIG_SYS_LBLAWAR2_PRELIM	0x00000000
 
 #define CONFIG_SYS_BR3_PRELIM		0x00000000
 #define CONFIG_SYS_OR3_PRELIM		0x00000000
-#define CONFIG_SYS_LBLAWBAR3_PRELIM	0x00000000
-#define CONFIG_SYS_LBLAWAR3_PRELIM	0x00000000
 
 /*
  * Monitor config
@@ -265,150 +216,15 @@
 				/* Initial Memory map for Linux */
 #define CONFIG_SYS_BOOTMAPSZ	(256 << 20)
 
-#define CONFIG_SYS_HRCW_LOW (\
-	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
-	HRCWL_DDR_TO_SCB_CLK_1X1 |\
-	HRCWL_CSB_TO_CLKIN_4X1 |\
-	HRCWL_VCO_1X2 |\
-	HRCWL_CORE_TO_CSB_2X1)
-
-#if defined(PCI_64BIT)
-#define CONFIG_SYS_HRCW_HIGH (\
-	HRCWH_PCI_HOST |\
-	HRCWH_64_BIT_PCI |\
-	HRCWH_PCI1_ARBITER_ENABLE |\
-	HRCWH_PCI2_ARBITER_DISABLE |\
-	HRCWH_CORE_ENABLE |\
-	HRCWH_FROM_0X00000100 |\
-	HRCWH_BOOTSEQ_DISABLE |\
-	HRCWH_SW_WATCHDOG_DISABLE |\
-	HRCWH_ROM_LOC_LOCAL_16BIT |\
-	HRCWH_TSEC1M_IN_GMII |\
-	HRCWH_TSEC2M_IN_GMII)
-#else
-#define CONFIG_SYS_HRCW_HIGH (\
-	HRCWH_PCI_HOST |\
-	HRCWH_32_BIT_PCI |\
-	HRCWH_PCI1_ARBITER_ENABLE |\
-	HRCWH_PCI2_ARBITER_DISABLE |\
-	HRCWH_CORE_ENABLE |\
-	HRCWH_FROM_0X00000100 |\
-	HRCWH_BOOTSEQ_DISABLE |\
-	HRCWH_SW_WATCHDOG_DISABLE |\
-	HRCWH_ROM_LOC_LOCAL_16BIT |\
-	HRCWH_TSEC1M_IN_GMII |\
-	HRCWH_TSEC2M_IN_GMII)
-#endif
-
 /* System IO Config */
 #define CONFIG_SYS_SICRH	0
 #define CONFIG_SYS_SICRL	SICRL_LDP_A
 
-/* i-cache and d-cache disabled */
-#define CONFIG_SYS_HID0_INIT	0x000000000
-#define CONFIG_SYS_HID0_FINAL	(CONFIG_SYS_HID0_INIT | \
-				 HID0_ENABLE_INSTRUCTION_CACHE)
-#define CONFIG_SYS_HID2	HID2_HBE
-
-#define CONFIG_HIGH_BATS	1	/* High BATs supported */
-
-/* DDR 0 - 512M */
-#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_SDRAM_BASE + 0x10000000 \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_SDRAM_BASE + 0x10000000 \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-
-/* stack in DCACHE @ 512M (no backing mem) */
-#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_INIT_RAM_ADDR \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_INIT_RAM_ADDR \
-				| BATU_BL_128K \
-				| BATU_VS \
-				| BATU_VP)
-
 /* PCI */
 #ifdef CONFIG_PCI
 #define CONFIG_PCI_INDIRECT_BRIDGE
-#define CONFIG_SYS_IBAT3L	(CONFIG_SYS_PCI1_MEM_BASE \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT3U	(CONFIG_SYS_PCI1_MEM_BASE \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_IBAT4L	(CONFIG_SYS_PCI1_MMIO_BASE \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT4U	(CONFIG_SYS_PCI1_MMIO_BASE \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_IBAT5L	(CONFIG_SYS_PCI1_IO_BASE \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT5U	(CONFIG_SYS_PCI1_IO_BASE \
-				| BATU_BL_16M \
-				| BATU_VS \
-				| BATU_VP)
-#else
-#define CONFIG_SYS_IBAT3L	(0)
-#define CONFIG_SYS_IBAT3U	(0)
-#define CONFIG_SYS_IBAT4L	(0)
-#define CONFIG_SYS_IBAT4U	(0)
-#define CONFIG_SYS_IBAT5L	(0)
-#define CONFIG_SYS_IBAT5U	(0)
 #endif
 
-/* IMMRBAR */
-#define CONFIG_SYS_IBAT6L	(CONFIG_SYS_IMMR \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT6U	(CONFIG_SYS_IMMR \
-				| BATU_BL_1M \
-				| BATU_VS \
-				| BATU_VP)
-
-/* FLASH */
-#define CONFIG_SYS_IBAT7L	(CONFIG_SYS_FLASH_BASE \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT7U	(CONFIG_SYS_FLASH_BASE \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-
-#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
-#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
-#define CONFIG_SYS_DBAT2L	CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
-#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
-#define CONFIG_SYS_DBAT4L	CONFIG_SYS_IBAT4L
-#define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U
-#define CONFIG_SYS_DBAT5L	CONFIG_SYS_IBAT5L
-#define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
-#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
-#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
-#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
-
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
 #endif
diff --git a/include/configs/caddy2.h b/include/configs/caddy2.h
new file mode 100644
index 0000000000..15ac17985f
--- /dev/null
+++ b/include/configs/caddy2.h
@@ -0,0 +1,334 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * esd vme8349 U-Boot configuration file
+ * Copyright (c) 2008, 2009 esd gmbh Hannover Germany
+ *
+ * (C) Copyright 2006-2010
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * reinhard.arlt@esd-electronics.de
+ * Based on the MPC8349EMDS config.
+ */
+
+/*
+ * vme8349 board configuration file.
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300		1	/* E300 Family */
+
+/* Don't enable PCI2 on vme834x - it doesn't exist physically. */
+#undef CONFIG_MPC83XX_PCI2		/* support for 2nd PCI controller */
+
+#undef CONFIG_SYS_DRAM_TEST			/* memory test, takes time */
+#define CONFIG_SYS_MEMTEST_START	0x00000000	/* memtest region */
+#define CONFIG_SYS_MEMTEST_END		0x00100000
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_DDR_ECC			/* only for ECC DDR module */
+#define CONFIG_DDR_ECC_CMD		/* use DDR ECC user commands */
+#define CONFIG_SPD_EEPROM
+#define SPD_EEPROM_ADDRESS		0x54
+#define CONFIG_SYS_READ_SPD		vme8349_read_spd
+#define CONFIG_SYS_83XX_DDR_USES_CS0	/* esd; Fsl board uses CS2/CS3 */
+
+/*
+ * 32-bit data path mode.
+ *
+ * Please note that using this mode for devices with the real density of 64-bit
+ * effectively reduces the amount of available memory due to the effect of
+ * wrapping around while translating address to row/columns, for example in the
+ * 256MB module the upper 128MB get aliased with contents of the lower
+ * 128MB); normally this define should be used for devices with real 32-bit
+ * data path.
+ */
+#undef CONFIG_DDR_32BIT
+
+#define CONFIG_SYS_SDRAM_BASE		0x00000000	/* DDR is sys memory*/
+#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN \
+					| DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075)
+#define CONFIG_DDR_2T_TIMING
+#define CONFIG_SYS_DDRCDR		(DDRCDR_DHC_EN \
+					| DDRCDR_ODT \
+					| DDRCDR_Q_DRN)
+					/* 0x80080001 */
+
+/*
+ * FLASH on the Local Bus
+ */
+#define CONFIG_SYS_FLASH_BASE		0xffc00000	/* start of FLASH   */
+#define CONFIG_SYS_FLASH_SIZE		4		/* flash size in MB */
+
+
+#define CONFIG_SYS_WINDOW1_BASE		0xf0000000
+
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device*/
+
+#undef CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase TO (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write TO (ms) */
+
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
+
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_RAMBOOT
+#else
+#undef CONFIG_SYS_RAMBOOT
+#endif
+
+#define CONFIG_SYS_INIT_RAM_LOCK	1
+#define CONFIG_SYS_INIT_RAM_ADDR	0xF7000000	/* Initial RAM addr */
+#define CONFIG_SYS_INIT_RAM_SIZE		0x1000		/* size */
+
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
+					 GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB */
+#define CONFIG_SYS_MALLOC_LEN		(256 * 1024)	/* Malloc size */
+
+#undef CONFIG_SYS_LB_SDRAM	/* if board has SDRAM on local bus */
+
+/*
+ * Serial Port
+ */
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
+
+#define CONFIG_SYS_BAUDRATE_TABLE  \
+		{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+
+#define CONFIG_SYS_NS16550_COM1		(CONFIG_SYS_IMMR + 0x4500)
+#define CONFIG_SYS_NS16550_COM2		(CONFIG_SYS_IMMR + 0x4600)
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED	400000
+#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED	400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
+#define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x69} }
+/* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */
+
+#define CONFIG_SYS_I2C_8574_ADDR2       0x20    /* I2C1, PCF8574 */
+
+/* TSEC */
+#define CONFIG_SYS_TSEC1_OFFSET	0x24000
+#define CONFIG_SYS_TSEC1	(CONFIG_SYS_IMMR + CONFIG_SYS_TSEC1_OFFSET)
+#define CONFIG_SYS_TSEC2_OFFSET 0x25000
+#define CONFIG_SYS_TSEC2	(CONFIG_SYS_IMMR + CONFIG_SYS_TSEC2_OFFSET)
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CONFIG_SYS_PCI1_MEM_BASE	0x80000000
+#define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BASE
+#define CONFIG_SYS_PCI1_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCI1_MMIO_BASE	0x90000000
+#define CONFIG_SYS_PCI1_MMIO_PHYS	CONFIG_SYS_PCI1_MMIO_BASE
+#define CONFIG_SYS_PCI1_MMIO_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCI1_IO_BASE		0x00000000
+#define CONFIG_SYS_PCI1_IO_PHYS		0xE2000000
+#define CONFIG_SYS_PCI1_IO_SIZE		0x00100000	/* 1M */
+
+#define CONFIG_SYS_PCI2_MEM_BASE	0xA0000000
+#define CONFIG_SYS_PCI2_MEM_PHYS	CONFIG_SYS_PCI2_MEM_BASE
+#define CONFIG_SYS_PCI2_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCI2_MMIO_BASE	0xB0000000
+#define CONFIG_SYS_PCI2_MMIO_PHYS	CONFIG_SYS_PCI2_MMIO_BASE
+#define CONFIG_SYS_PCI2_MMIO_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCI2_IO_BASE		0x00000000
+#define CONFIG_SYS_PCI2_IO_PHYS		0xE2100000
+#define CONFIG_SYS_PCI2_IO_SIZE		0x00100000	/* 1M */
+
+#if defined(CONFIG_PCI)
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_TULIP
+
+#if !defined(CONFIG_PCI_PNP)
+	#define PCI_ENET0_IOADDR	0xFIXME
+	#define PCI_ENET0_MEMADDR	0xFIXME
+	#define PCI_IDSEL_NUMBER	0xFIXME
+#endif
+
+#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID	0x1957	/* Freescale */
+
+#endif	/* CONFIG_PCI */
+
+/*
+ * TSEC configuration
+ */
+
+#if defined(CONFIG_TSEC_ENET)
+
+#define CONFIG_GMII			/* MII PHY management */
+#define CONFIG_TSEC1
+#define CONFIG_TSEC1_NAME	"TSEC0"
+#define CONFIG_TSEC2
+#define CONFIG_TSEC2_NAME	"TSEC1"
+#define CONFIG_PHY_M88E1111
+#define TSEC1_PHY_ADDR		0x08
+#define TSEC2_PHY_ADDR		0x10
+#define TSEC1_PHYIDX		0
+#define TSEC2_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
+
+/* Options are: TSEC[0-1] */
+#define CONFIG_ETHPRIME		"TSEC0"
+
+#endif	/* CONFIG_TSEC_ENET */
+
+/*
+ * Environment
+ */
+#ifndef CONFIG_SYS_RAMBOOT
+	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + 0xc0000)
+	#define CONFIG_ENV_SECT_SIZE	0x20000	/* 128K(one sector) for env */
+	#define CONFIG_ENV_SIZE		0x2000
+
+/* Address and size of Redundant Environment Sector	*/
+#define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
+
+#else
+	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
+	#define CONFIG_ENV_SIZE		0x2000
+#endif
+
+#define CONFIG_LOADS_ECHO		/* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+
+/*
+ * Command line configuration.
+ */
+#define CONFIG_SYS_RTC_BUS_NUM  0x01
+#define CONFIG_SYS_I2C_RTC_ADDR	0x32
+#define CONFIG_RTC_RX8025
+
+/* Pass Ethernet MAC to VxWorks */
+#define CONFIG_SYS_VXWORKS_MAC_PTR	0x000043f0
+
+#undef CONFIG_WATCHDOG			/* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 256 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ	(256 << 20)	/* Init Memory map for Linux*/
+
+#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST  */
+
+/* System IO Config */
+#define CONFIG_SYS_SICRH 0
+#define CONFIG_SYS_SICRL SICRL_LDP_A
+
+#define CONFIG_SYS_GPIO1_PRELIM
+#define CONFIG_SYS_GPIO1_DIR	0x00100000
+#define CONFIG_SYS_GPIO1_DAT	0x00100000
+
+#define CONFIG_SYS_GPIO2_PRELIM
+#define CONFIG_SYS_GPIO2_DIR	0x78900000
+#define CONFIG_SYS_GPIO2_DAT	0x70100000
+
+#ifdef CONFIG_PCI
+#define CONFIG_PCI_INDIRECT_BRIDGE
+#endif
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
+#endif
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_OVERWRITE
+
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
+#define CONFIG_HAS_ETH1
+#endif
+
+#define CONFIG_HOSTNAME		"VME8349"
+#define CONFIG_ROOTPATH		"/tftpboot/rootfs"
+#define CONFIG_BOOTFILE		"uImage"
+
+#define CONFIG_LOADADDR		800000	/* def location for tftp and bootm */
+
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	"netdev=eth0\0"							\
+	"hostname=vme8349\0"						\
+	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
+		"nfsroot=${serverip}:${rootpath}\0"			\
+	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
+	"addip=setenv bootargs ${bootargs} "				\
+		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
+		":${hostname}:${netdev}:off panic=1\0"			\
+	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
+	"flash_nfs=run nfsargs addip addtty;"				\
+		"bootm ${kernel_addr}\0"				\
+	"flash_self=run ramargs addip addtty;"				\
+		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
+	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"	\
+		"bootm\0"						\
+	"load=tftp 100000 /tftpboot/bdi2000/vme8349.bin\0"		\
+	"update=protect off fff00000 fff3ffff; "			\
+		"era fff00000 fff3ffff; cp.b 100000 fff00000 ${filesize}\0" \
+	"upd=run load update\0"						\
+	"fdtaddr=780000\0"						\
+	"fdtfile=vme8349.dtb\0"						\
+	""
+
+#define CONFIG_NFSBOOTCOMMAND						\
+	"setenv bootargs root=/dev/nfs rw "				\
+		"nfsroot=$serverip:$rootpath "				\
+		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"	\
+							"$netdev:off "	\
+		"console=$consoledev,$baudrate $othbootargs;"		\
+	"tftp $loadaddr $bootfile;"					\
+	"tftp $fdtaddr $fdtfile;"					\
+	"bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND						\
+	"setenv bootargs root=/dev/ram rw "				\
+		"console=$consoledev,$baudrate $othbootargs;"		\
+	"tftp $ramdiskaddr $ramdiskfile;"				\
+	"tftp $loadaddr $bootfile;"					\
+	"tftp $fdtaddr $fdtfile;"					\
+	"bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND	"run flash_self"
+
+#ifndef __ASSEMBLY__
+int vme8349_read_spd(unsigned char chip, unsigned int addr, int alen,
+		     unsigned char *buffer, int len);
+#endif
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/gazerbeam.h b/include/configs/gazerbeam.h
new file mode 100644
index 0000000000..11d367a151
--- /dev/null
+++ b/include/configs/gazerbeam.h
@@ -0,0 +1,137 @@
+/*
+ * (C) Copyright 2015
+ * Dirk Eibach,  Guntermann & Drunck GmbH, eibach@gdsys.de
+ *
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_SYS_SDRAM_BASE		0x00000000 /* DDR is system memory */
+/* TODO: Check: Can this be unified with CONFIG_SYS_SDRAM_BASE? */
+#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_SDRAM_BASE
+
+/*
+ * Memory test
+ * TODO: Migrate!
+ */
+#define CONFIG_SYS_MEMTEST_START	0x00001000 /* memtest region */
+#define CONFIG_SYS_MEMTEST_END		0x07e00000
+
+/*
+ * The reserved memory
+ */
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE /* start of monitor */
+
+#define CONFIG_SYS_MONITOR_LEN	(512 * 1024) /* Reserve 512 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN	(512 * 1024) /* Reserved for malloc */
+
+/*
+ * Initial RAM Base Address Setup
+ */
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_SIZE	0x1000 /* Size of used area in RAM */
+#define CONFIG_SYS_GBL_DATA_OFFSET	\
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+
+/*
+ * FLASH on the Local Bus
+ */
+#define CONFIG_SYS_FLASH_BASE		0xFE000000 /* FLASH base address */
+#define CONFIG_SYS_FLASH_SIZE		8 /* FLASH size is up to 8M */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	1 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	135
+
+#define CONFIG_SYS_BAUDRATE_TABLE  \
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+/*
+ * Environment
+ */
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + \
+				 CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_ENV_SECT_SIZE	0x10000 /* 64K(one sector) for env */
+#define CONFIG_ENV_SIZE		0x2000
+#define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND	CONFIG_ENV_SIZE
+
+#define CONFIG_LOADS_ECHO		/* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LOAD_ADDR		0x2000000 /* default load address */
+#define CONFIG_SYS_HZ		1000	/* decrementer freq: 1ms ticks */
+
+#define CONFIG_SYS_CBSIZE	1024 /* Console I/O Buffer Size */
+
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS	16	/* max number of command args */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 256 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ	(256 << 20) /* Initial Memory map for Linux */
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_HAS_ETH0
+#define CONFIG_HAS_ETH1
+
+#define CONFIG_LOADADDR	800000	/* default location for tftp and bootm */
+
+/* TODO: Turn into string option and migrate to Kconfig */
+#define CONFIG_HOSTNAME		"gazerbeam"
+#define CONFIG_ROOTPATH		"/opt/nfsroot"
+#define CONFIG_BOOTFILE		"uImage"
+
+#define CONFIG_PREBOOT		/* enable preboot variable */
+
+#define CONFIG_EXTRA_ENV_SETTINGS					\
+	"netdev=eth0\0"							\
+	"consoledev=ttyS1\0"						\
+	"u-boot=u-boot.bin\0"						\
+	"kernel_addr=1000000\0"					\
+	"fdt_addr=C00000\0"						\
+	"fdtfile=hrcon.dtb\0"				\
+	"load=tftp ${loadaddr} ${u-boot}\0"				\
+	"update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE)	\
+		" +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\
+		" +${filesize};cp.b ${fileaddr} "			\
+		__stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0"	\
+	"upd=run load update\0"						\
+
+#define CONFIG_NFSBOOTCOMMAND						\
+	"setenv bootargs root=/dev/nfs rw "				\
+	"nfsroot=$serverip:$rootpath "					\
+	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+	"console=$consoledev,$baudrate $othbootargs;"			\
+	"tftp ${kernel_addr} $bootfile;"				\
+	"tftp ${fdt_addr} $fdtfile;"					\
+	"bootm ${kernel_addr} - ${fdt_addr}"
+
+#define CONFIG_MMCBOOTCOMMAND						\
+	"setenv bootargs root=/dev/mmcblk0p3 rw rootwait "		\
+	"console=$consoledev,$baudrate $othbootargs;"			\
+	"ext2load mmc 0:2 ${kernel_addr} $bootfile;"			\
+	"ext2load mmc 0:2 ${fdt_addr} $fdtfile;"			\
+	"bootm ${kernel_addr} - ${fdt_addr}"
+
+#define CONFIG_BOOTCOMMAND		CONFIG_MMCBOOTCOMMAND
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/hrcon.h b/include/configs/hrcon.h
index 52e62778a3..6e6c1714ce 100644
--- a/include/configs/hrcon.h
+++ b/include/configs/hrcon.h
@@ -12,100 +12,19 @@
  * High Level Configuration Options
  */
 #define CONFIG_E300		1 /* E300 family */
-#define CONFIG_MPC83xx		1 /* MPC83xx family */
-#define CONFIG_MPC830x		1 /* MPC830x family */
-#define CONFIG_MPC8308		1 /* MPC8308 CPU specific */
-#define CONFIG_HRCON		1 /* HRCON board specific */
 
 #define CONFIG_SYS_FSL_ESDHC_ADDR	CONFIG_SYS_MPC83xx_ESDHC_ADDR
 
 /*
- * System Clock Setup
- */
-#define CONFIG_83XX_CLKIN	33333333 /* in Hz */
-#define CONFIG_SYS_CLK_FREQ	CONFIG_83XX_CLKIN
-
-/*
- * Hardware Reset Configuration Word
- * if CLKIN is 66.66MHz, then
- * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz
- * We choose the A type silicon as default, so the core is 400Mhz.
- */
-#define CONFIG_SYS_HRCW_LOW (\
-	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
-	HRCWL_DDR_TO_SCB_CLK_2X1 |\
-	HRCWL_SVCOD_DIV_2 |\
-	HRCWL_CSB_TO_CLKIN_4X1 |\
-	HRCWL_CORE_TO_CSB_3X1)
-/*
- * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits
- * in 8308's HRCWH according to the manual, but original Freescale's
- * code has them and I've expirienced some problems using the board
- * with BDI3000 attached when I've tried to set these bits to zero
- * (UART doesn't work after the 'reset run' command).
- */
-#define CONFIG_SYS_HRCW_HIGH (\
-	HRCWH_PCI_HOST |\
-	HRCWH_PCI1_ARBITER_ENABLE |\
-	HRCWH_CORE_ENABLE |\
-	HRCWH_FROM_0XFFF00100 |\
-	HRCWH_BOOTSEQ_DISABLE |\
-	HRCWH_SW_WATCHDOG_DISABLE |\
-	HRCWH_ROM_LOC_LOCAL_16BIT |\
-	HRCWH_RL_EXT_LEGACY |\
-	HRCWH_TSEC1M_IN_RGMII |\
-	HRCWH_TSEC2M_IN_RGMII |\
-	HRCWH_BIG_ENDIAN)
-
-/*
- * System IO Config
- */
-#define CONFIG_SYS_SICRH (\
-	SICRH_ESDHC_A_SD |\
-	SICRH_ESDHC_B_SD |\
-	SICRH_ESDHC_C_SD |\
-	SICRH_GPIO_A_GPIO |\
-	SICRH_GPIO_B_GPIO |\
-	SICRH_IEEE1588_A_GPIO |\
-	SICRH_USB |\
-	SICRH_GTM_GPIO |\
-	SICRH_IEEE1588_B_GPIO |\
-	SICRH_ETSEC2_GPIO |\
-	SICRH_GPIOSEL_1 |\
-	SICRH_TMROBI_V3P3 |\
-	SICRH_TSOBI1_V2P5 |\
-	SICRH_TSOBI2_V2P5)	/* 0x0037f103 */
-#define CONFIG_SYS_SICRL (\
-	SICRL_SPI_PF0 |\
-	SICRL_UART_PF0 |\
-	SICRL_IRQ_PF0 |\
-	SICRL_I2C2_PF0 |\
-	SICRL_ETSEC1_GTX_CLK125)	/* 0x00000000 */
-
-/*
- * IMMR new address
- */
-#define CONFIG_SYS_IMMR		0xE0000000
-
-/*
  * SERDES
  */
 #define CONFIG_FSL_SERDES
 #define CONFIG_FSL_SERDES1	0xe3000
 
 /*
- * Arbiter Setup
- */
-#define CONFIG_SYS_ACR_PIPE_DEP	3 /* Arbiter pipeline depth is 4 */
-#define CONFIG_SYS_ACR_RPTCNT	3 /* Arbiter repeat count is 4 */
-#define CONFIG_SYS_SPCR_TSECEP	3 /* eTSEC emergency priority is highest */
-
-/*
  * DDR Setup
  */
-#define CONFIG_SYS_DDR_BASE		0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_SDRAM_BASE		0x00000000 /* DDR is system memory */
 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
 #define CONFIG_SYS_DDRCDR_VALUE	(DDRCDR_EN \
 				| DDRCDR_PZ_LOZ \
@@ -192,13 +111,6 @@
 	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 
 /*
- * Local Bus Configuration & Clock Setup
- */
-#define CONFIG_SYS_LCRR_DBYP		LCRR_DBYP
-#define CONFIG_SYS_LCRR_CLKDIV		LCRR_CLKDIV_2
-#define CONFIG_SYS_LBC_LBCR		0x00040000
-
-/*
  * FLASH on the Local Bus
  */
 #if 1
@@ -210,22 +122,6 @@
 #define CONFIG_SYS_FLASH_BASE		0xFE000000 /* FLASH base address */
 #define CONFIG_SYS_FLASH_SIZE		8 /* FLASH size is up to 8M */
 
-/* Window base at flash base */
-#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_8MB)
-
-#define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE \
-				| BR_PS_16	/* 16 bit port */ \
-				| BR_MS_GPCM	/* MSEL = GPCM */ \
-				| BR_V)		/* valid */
-#define CONFIG_SYS_OR0_PRELIM	(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
-				| OR_UPM_XAM \
-				| OR_GPCM_CSNT \
-				| OR_GPCM_ACS_DIV2 \
-				| OR_GPCM_XACS \
-				| OR_GPCM_SCY_15 \
-				| OR_GPCM_TRLX_SET \
-				| OR_GPCM_EHTR_SET)
 
 #define CONFIG_SYS_MAX_FLASH_BANKS	1 /* number of banks */
 #define CONFIG_SYS_MAX_FLASH_SECT	135
@@ -233,30 +129,6 @@
 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000 /* Flash Erase Timeout (ms) */
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500 /* Flash Write Timeout (ms) */
 
-/*
- * FPGA
- */
-#define CONFIG_SYS_FPGA0_BASE		0xE0600000
-#define CONFIG_SYS_FPGA0_SIZE		1 /* FPGA size is 1M */
-
-/* Window base at FPGA base */
-#define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_FPGA0_BASE
-#define CONFIG_SYS_LBLAWAR1_PRELIM	(LBLAWAR_EN | LBLAWAR_1MB)
-
-#define CONFIG_SYS_BR1_PRELIM	(CONFIG_SYS_FPGA0_BASE \
-				| BR_PS_16	/* 16 bit port */ \
-				| BR_MS_GPCM	/* MSEL = GPCM */ \
-				| BR_V)		/* valid */
-#define CONFIG_SYS_OR1_PRELIM	(MEG_TO_AM(CONFIG_SYS_FPGA0_SIZE) \
-				| OR_UPM_XAM \
-				| OR_GPCM_CSNT \
-				| OR_GPCM_ACS_DIV2 \
-				| OR_GPCM_XACS \
-				| OR_GPCM_SCY_15 \
-				| OR_GPCM_TRLX_SET \
-				| OR_GPCM_EHTR_SET)
-
-#define CONFIG_SYS_FPGA_BASE(k)		CONFIG_SYS_FPGA0_BASE
 #define CONFIG_SYS_FPGA_DONE(k)		0x0010
 
 #define CONFIG_SYS_FPGA_COUNT		1
@@ -515,52 +387,6 @@ void fpga_control_clear(unsigned int bus, int pin);
 #define CONFIG_SYS_BOOTMAPSZ	(256 << 20) /* Initial Memory map for Linux */
 
 /*
- * Core HID Setup
- */
-#define CONFIG_SYS_HID0_INIT	0x000000000
-#define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK | \
-				 HID0_ENABLE_INSTRUCTION_CACHE | \
-				 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
-#define CONFIG_SYS_HID2		HID2_HBE
-
-/*
- * MMU Setup
- */
-
-/* DDR: cache cacheable */
-#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \
-					BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \
-					BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
-
-/* IMMRBAR, PCI IO and FPGA: cache-inhibit and guarded */
-#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_IMMR | BATL_PP_RW | \
-			BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \
-					BATU_VP)
-#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
-
-/* FLASH: icache cacheable, but dcache-inhibit and guarded */
-#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
-					BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \
-					BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT2L	(CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
-					BATL_CACHEINHIBIT | \
-					BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
-
-/* Stack in dcache: cacheable, no memory coherence */
-#define CONFIG_SYS_IBAT3L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
-#define CONFIG_SYS_IBAT3U	(CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
-					BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
-
-/*
  * Environment Configuration
  */
 
diff --git a/include/configs/ids8313.h b/include/configs/ids8313.h
index 7e4c497fe0..b1d01c58f9 100644
--- a/include/configs/ids8313.h
+++ b/include/configs/ids8313.h
@@ -14,56 +14,17 @@
 /*
  * High Level Configuration Options
  */
-#define CONFIG_MPC831x
-#define CONFIG_MPC8313
-
 #define CONFIG_FSL_ELBC
 
 #define CONFIG_BOOT_RETRY_TIME		900
 #define CONFIG_BOOT_RETRY_MIN		30
 #define CONFIG_RESET_TO_RETRY
 
-#define CONFIG_83XX_CLKIN		66000000	/* in Hz */
-#define CONFIG_SYS_CLK_FREQ		CONFIG_83XX_CLKIN
-
-#define CONFIG_SYS_IMMR		0xF0000000
-
-#define CONFIG_SYS_ACR_PIPE_DEP	3	/* Arbiter pipeline depth (0-3) */
-#define CONFIG_SYS_ACR_RPTCNT		3	/* Arbiter repeat count (0-7) */
-
-/*
- * Hardware Reset Configuration Word
- * if CLKIN is 66.000MHz, then
- * CSB = 132MHz, CORE = 264MHz, DDRC = 264MHz, LBC = 132MHz
- */
-#define CONFIG_SYS_HRCW_LOW (0x20000000 /* reserved, must be set */ |\
-			     HRCWL_DDR_TO_SCB_CLK_2X1 |\
-			     HRCWL_CSB_TO_CLKIN_2X1 |\
-			     HRCWL_CORE_TO_CSB_2X1)
-
-#define CONFIG_SYS_HRCW_HIGH	(HRCWH_PCI_HOST |\
-				 HRCWH_CORE_ENABLE |\
-				 HRCWH_FROM_0XFFF00100 |\
-				 HRCWH_BOOTSEQ_DISABLE |\
-				 HRCWH_SW_WATCHDOG_DISABLE |\
-				 HRCWH_ROM_LOC_LOCAL_8BIT |\
-				 HRCWH_RL_EXT_LEGACY |\
-				 HRCWH_TSEC1M_IN_MII |\
-				 HRCWH_TSEC2M_IN_MII |\
-				 HRCWH_BIG_ENDIAN)
-
 #define CONFIG_SYS_SICRH	0x00000000
 #define CONFIG_SYS_SICRL	(SICRL_LBC | SICRL_SPI_D)
 
 #define CONFIG_HWCONFIG
 
-#define CONFIG_SYS_HID0_INIT	0x000000000
-#define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK |\
-				 HID0_ENABLE_INSTRUCTION_CACHE |\
-				 HID0_DISABLE_DYNAMIC_POWER_MANAGMENT)
-
-#define CONFIG_SYS_HID2	(HID2_HBE | 0x00020000)
-
 /*
  * Definitions for initial stack pointer and data area (in DCACHE )
  */
@@ -76,25 +37,12 @@
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
 /*
- * Local Bus LCRR and LBCR regs
- */
-#define CONFIG_SYS_LCRR_EADC		LCRR_EADC_1
-#define CONFIG_SYS_LCRR_CLKDIV		LCRR_CLKDIV_2
-#define CONFIG_SYS_LBC_LBCR		(0x00040000 |\
-					 (0xFF << LBCR_BMT_SHIFT) |\
-					 0xF)
-
-#define CONFIG_SYS_LBC_MRTPR		0x20000000
-
-/*
  * Internal Definitions
  */
 /*
  * DDR Setup
  */
-#define CONFIG_SYS_DDR_BASE		0x00000000
-#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_SDRAM_BASE		0x00000000
 
 /*
  * Manually set up DDR parameters,
@@ -169,20 +117,7 @@
 #define CONFIG_SYS_FLASH_BASE		0xFF800000
 #define CONFIG_SYS_FLASH_SIZE		8
 
-#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM	0x80000016
 
-#define CONFIG_SYS_BR0_PRELIM		(CONFIG_SYS_FLASH_BASE |\
-					 BR_PS_8 |\
-					 BR_MS_GPCM |\
-					 BR_V)
-
-#define CONFIG_SYS_OR0_PRELIM		(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) |\
-					 OR_GPCM_SCY_10 |\
-					 OR_GPCM_EHTR |\
-					 OR_GPCM_TRLX |\
-					 OR_GPCM_CSNT |\
-					 OR_GPCM_EAD)
 #define CONFIG_SYS_MAX_FLASH_BANKS	1
 #define CONFIG_SYS_MAX_FLASH_SECT	128
 
@@ -200,60 +135,24 @@
 #define CONFIG_SYS_NAND_BLOCK_SIZE	(128 << 10)
 #define NAND_CACHE_PAGES		64
 
-#define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_NAND_BASE
-#define CONFIG_SYS_LBLAWAR1_PRELIM	0x8000000E
-#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM
-#define CONFIG_SYS_NAND_LBLAWAR_PRELIM	CONFIG_SYS_LBLAWAR1_PRELIM
-
-#define CONFIG_SYS_BR1_PRELIM	((CONFIG_SYS_NAND_BASE) |\
-				 (2<<BR_DECC_SHIFT) |\
-				 BR_PS_8 |\
-				 BR_MS_FCM |\
-				 BR_V)
-
-#define CONFIG_SYS_OR1_PRELIM	(0xFFFF8000 |\
-				 OR_FCM_PGS |\
-				 OR_FCM_CSCT |\
-				 OR_FCM_CST |\
-				 OR_FCM_CHT |\
-				 OR_FCM_SCY_4 |\
-				 OR_FCM_TRLX |\
-				 OR_FCM_EHTR |\
-				 OR_FCM_RST)
 
 /*
  * MRAM setup
  */
 #define CONFIG_SYS_MRAM_BASE		0xE2000000
 #define CONFIG_SYS_MRAM_SIZE		0x20000	/* 128 Kb */
-#define CONFIG_SYS_LBLAWBAR2_PRELIM	CONFIG_SYS_MRAM_BASE
-#define CONFIG_SYS_LBLAWAR2_PRELIM	0x80000010	/* 128 Kb  */
 
 #define CONFIG_SYS_OR_TIMING_MRAM
 
-#define CONFIG_SYS_BR2_PRELIM		(CONFIG_SYS_MRAM_BASE |\
-					 BR_PS_8 |\
-					 BR_MS_GPCM |\
-					 BR_V)
-
-#define CONFIG_SYS_OR2_PRELIM		0xFFFE0C74
 
 /*
  * CPLD setup
  */
 #define CONFIG_SYS_CPLD_BASE		0xE3000000
 #define CONFIG_SYS_CPLD_SIZE		0x8000
-#define CONFIG_SYS_LBLAWBAR3_PRELIM	CONFIG_SYS_CPLD_BASE
-#define CONFIG_SYS_LBLAWAR3_PRELIM	0x8000000E
 
 #define CONFIG_SYS_OR_TIMING_MRAM
 
-#define CONFIG_SYS_BR3_PRELIM		(CONFIG_SYS_CPLD_BASE |\
-					 BR_PS_8 |\
-					 BR_MS_GPCM |\
-					 BR_V)
-
-#define CONFIG_SYS_OR3_PRELIM		0xFFFF8814
 
 /*
  * HW-Watchdog
@@ -304,90 +203,12 @@
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
 #define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR + 0x4500)
 #define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR + 0x4600)
-#define CONFIG_SYS_NS16550_CLK		(CONFIG_83XX_CLKIN * 2)
+#define CONFIG_SYS_NS16550_CLK		(get_bus_freq(0))
 
 #define CONFIG_HAS_FSL_DR_USB
 #define CONFIG_SYS_SCCR_USBDRCM	3
 
 /*
- * BAT's
- */
-#define CONFIG_HIGH_BATS
-
-/* DDR @ 0x00000000 */
-#define CONFIG_SYS_IBAT0L		(CONFIG_SYS_SDRAM_BASE |\
-					 BATL_PP_10)
-#define CONFIG_SYS_IBAT0U		(CONFIG_SYS_SDRAM_BASE |\
-					 BATU_BL_256M |\
-					 BATU_VS |\
-					 BATU_VP)
-#define CONFIG_SYS_DBAT0L		CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U		CONFIG_SYS_IBAT0U
-
-/* Initial RAM @ 0xFD000000 */
-#define CONFIG_SYS_IBAT1L		(CONFIG_SYS_INIT_RAM_ADDR |\
-					 BATL_PP_10 |\
-					 BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT1U		(CONFIG_SYS_INIT_RAM_ADDR |\
-					 BATU_BL_256K |\
-					 BATU_VS |\
-					 BATU_VP)
-#define CONFIG_SYS_DBAT1L		CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U		CONFIG_SYS_IBAT1U
-
-/* FLASH @ 0xFF800000 */
-#define CONFIG_SYS_IBAT2L		(CONFIG_SYS_FLASH_BASE |\
-					 BATL_PP_10 |\
-					 BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT2U		(CONFIG_SYS_FLASH_BASE |\
-					 BATU_BL_8M |\
-					 BATU_VS |\
-					 BATU_VP)
-#define CONFIG_SYS_DBAT2L		(CONFIG_SYS_FLASH_BASE |\
-					 BATL_PP_10 |\
-					 BATL_CACHEINHIBIT |\
-					 BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT2U		CONFIG_SYS_IBAT2U
-
-#define CONFIG_SYS_IBAT3L		(0)
-#define CONFIG_SYS_IBAT3U		(0)
-#define CONFIG_SYS_DBAT3L		CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U		CONFIG_SYS_IBAT3U
-
-#define CONFIG_SYS_IBAT4L		(0)
-#define CONFIG_SYS_IBAT4U		(0)
-#define CONFIG_SYS_DBAT4L		CONFIG_SYS_IBAT4L
-#define CONFIG_SYS_DBAT4U		CONFIG_SYS_IBAT4U
-
-/* IMMRBAR @ 0xF0000000 */
-#define CONFIG_SYS_IBAT5L		(CONFIG_SYS_IMMR |\
-					 BATL_PP_10 |\
-					 BATL_CACHEINHIBIT |\
-					 BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT5U		(CONFIG_SYS_IMMR |\
-					 BATU_BL_128M |\
-					 BATU_VS |\
-					 BATU_VP)
-#define CONFIG_SYS_DBAT5L		CONFIG_SYS_IBAT5L
-#define CONFIG_SYS_DBAT5U		CONFIG_SYS_IBAT5U
-
-/* NAND-Flash @ 0xE1000000, MRAM @ 0xE2000000, CPLD @ 0xE3000000 */
-#define CONFIG_SYS_IBAT6L		(0xE0000000 |\
-					 BATL_PP_10 |\
-					 BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT6U		(0xE0000000 |\
-					 BATU_BL_256M |\
-					 BATU_VS |\
-					 BATU_VP)
-#define CONFIG_SYS_DBAT6L		CONFIG_SYS_IBAT6L
-#define CONFIG_SYS_DBAT6U		CONFIG_SYS_IBAT6U
-
-#define CONFIG_SYS_IBAT7L		(0)
-#define CONFIG_SYS_IBAT7U		(0)
-#define CONFIG_SYS_DBAT7L		CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U		CONFIG_SYS_IBAT7U
-
-/*
  * U-Boot environment setup
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
diff --git a/include/configs/km/km8309-common.h b/include/configs/km/km-mpc8309.h
index 0e0b1b4605..e89b7af061 100644
--- a/include/configs/km/km8309-common.h
+++ b/include/configs/km/km-mpc8309.h
@@ -1,26 +1,17 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2012 Keymile AG
- *                    Gerlando Falauto <gerlando.falauto@keymile.com>
- *
- * Based on km8321-common.h, see respective copyright notice for credits
- */
-
-#ifndef __CONFIG_KM8309_COMMON_H
-#define __CONFIG_KM8309_COMMON_H
-
 /*
  * High Level Configuration Options
  */
 #define CONFIG_E300		1	/* E300 family */
 #define CONFIG_QE		1	/* Has QE */
-#define CONFIG_MPC830x		1	/* MPC830x family */
-#define CONFIG_MPC8309		1	/* MPC8309 CPU specific */
 
 #define CONFIG_KM_DEF_ARCH	"arch=ppc_82xx\0"
 
-/* include common defines/options for all 83xx Keymile boards */
-#include "km83xx-common.h"
+/*
+ * System Clock Setup
+ */
+#define CONFIG_83XX_CLKIN		66000000
+#define CONFIG_SYS_CLK_FREQ		66000000
+#define CONFIG_83XX_PCICLK		66000000
 
 /* QE microcode/firmware address */
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
@@ -74,28 +65,6 @@
 #define CONFIG_SYS_GP2DIR 0xFF000000
 #define CONFIG_SYS_GP2ODR 0x00000000
 
-/*
- * Hardware Reset Configuration Word
- */
-#define CONFIG_SYS_HRCW_LOW (\
-	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 | \
-	HRCWL_DDR_TO_SCB_CLK_2X1 | \
-	HRCWL_CSB_TO_CLKIN_2X1 | \
-	HRCWL_CORE_TO_CSB_2X1 | \
-	HRCWL_CE_PLL_VCO_DIV_2 | \
-	HRCWL_CE_TO_PLL_1X3)
-
-#define CONFIG_SYS_HRCW_HIGH (\
-	HRCWH_PCI_AGENT | \
-	HRCWH_PCI_ARBITER_DISABLE | \
-	HRCWH_CORE_ENABLE | \
-	HRCWH_FROM_0X00000100 | \
-	HRCWH_BOOTSEQ_DISABLE | \
-	HRCWH_SW_WATCHDOG_DISABLE | \
-	HRCWH_ROM_LOC_LOCAL_16BIT | \
-	HRCWH_BIG_ENDIAN | \
-	HRCWH_LALE_NORMAL)
-
 #define CONFIG_SYS_DDRCDR (\
 	DDRCDR_EN | \
 	DDRCDR_PZ_MAXZ | \
@@ -156,21 +125,13 @@
 /* EEprom support */
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
 
-/*
- * Local Bus Configuration & Clock Setup
- */
-#define CONFIG_SYS_LCRR_DBYP	0x80000000
-#define CONFIG_SYS_LCRR_EADC	0x00010000
-#define CONFIG_SYS_LCRR_CLKDIV	0x00000002
-
-#define CONFIG_SYS_LBC_LBCR	0x00000000
-
-/*
- * MMU Setup
- */
-#define CONFIG_SYS_IBAT7L	(0)
-#define CONFIG_SYS_IBAT7U	(0)
-#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
-
-#endif /* __CONFIG_KM8309_COMMON_H */
+/* ethernet port connected to piggy (UEC2) */
+#define CONFIG_HAS_ETH1
+#define CONFIG_UEC_ETH2
+#define CONFIG_SYS_UEC2_UCC_NUM		2       /* UCC3 */
+#define CONFIG_SYS_UEC2_RX_CLK		QE_CLK_NONE /* not used in RMII Mode */
+#define CONFIG_SYS_UEC2_TX_CLK		QE_CLK12
+#define CONFIG_SYS_UEC2_ETH_TYPE	FAST_ETH
+#define CONFIG_SYS_UEC2_PHY_ADDR	0
+#define CONFIG_SYS_UEC2_INTERFACE_TYPE	PHY_INTERFACE_MODE_RMII
+#define CONFIG_SYS_UEC2_INTERFACE_SPEED	100
diff --git a/include/configs/km/km8321-common.h b/include/configs/km/km-mpc832x.h
index 41b3ba2842..3c2173d364 100644
--- a/include/configs/km/km8321-common.h
+++ b/include/configs/km/km-mpc832x.h
@@ -1,65 +1,34 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2006 Freescale Semiconductor, Inc.
- *                    Dave Liu <daveliu@freescale.com>
- *
- * Copyright (C) 2007 Logic Product Development, Inc.
- *                    Peter Barada <peterb@logicpd.com>
- *
- * Copyright (C) 2007 MontaVista Software, Inc.
- *                    Anton Vorontsov <avorontsov@ru.mvista.com>
- *
- * (C) Copyright 2008
- * Heiko Schocher, DENX Software Engineering, hs@denx.de.
- *
- * (C) Copyright 2010
- * Lukas Roggli, KEYMILE Ltd, lukas.roggli@keymile.com
- *
- * (C) Copyright 2010-2011
- * Thomas Reufer, KEYMILE Ltd, thomas.reufer@keymile.com
- */
-
-#ifndef __CONFIG_KM8321_COMMON_H
-#define __CONFIG_KM8321_COMMON_H
-
 /*
  * High Level Configuration Options
  */
 #define CONFIG_QE	/* Has QE */
-#define CONFIG_MPC832x	/* MPC832x CPU specific */
 #define CONFIG_KM8321	/* Keymile PBEC8321 board specific */
 
-#define CONFIG_KM_DEF_ARCH	"arch=ppc_8xx\0"
-
-/* include common defines/options for all 83xx Keymile boards */
-#include "km83xx-common.h"
+/*
+ * System Clock Setup
+ */
+#define CONFIG_83XX_CLKIN		66000000
+#define CONFIG_SYS_CLK_FREQ		66000000
+#define CONFIG_83XX_PCICLK		66000000
 
 /*
- * System IO Config
+ * QE UEC ethernet configuration
  */
-#define CONFIG_SYS_SICRL	SICRL_IRQ_CKS
+#define CONFIG_UEC_ETH1		/* GETH1 */
+#define UEC_VERBOSE_DEBUG	1
+
+#define CONFIG_SYS_UEC1_UCC_NUM	3	/* UCC4 */
+#define CONFIG_SYS_UEC1_RX_CLK		QE_CLK_NONE /* not used in RMII Mode */
+#define CONFIG_SYS_UEC1_TX_CLK		QE_CLK17
+#define CONFIG_SYS_UEC1_ETH_TYPE	FAST_ETH
+#define CONFIG_SYS_UEC1_PHY_ADDR	0
+#define CONFIG_SYS_UEC1_INTERFACE_TYPE	PHY_INTERFACE_MODE_RMII
+#define CONFIG_SYS_UEC1_INTERFACE_SPEED	100
 
 /*
- * Hardware Reset Configuration Word
+ * System IO Config
  */
-#define CONFIG_SYS_HRCW_LOW (\
-	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 | \
-	HRCWL_DDR_TO_SCB_CLK_2X1 | \
-	HRCWL_CSB_TO_CLKIN_2X1 | \
-	HRCWL_CORE_TO_CSB_2_5X1 | \
-	HRCWL_CE_PLL_VCO_DIV_2 | \
-	HRCWL_CE_TO_PLL_1X3)
-
-#define CONFIG_SYS_HRCW_HIGH (\
-	HRCWH_PCI_AGENT | \
-	HRCWH_PCI_ARBITER_DISABLE | \
-	HRCWH_CORE_ENABLE | \
-	HRCWH_FROM_0X00000100 | \
-	HRCWH_BOOTSEQ_DISABLE | \
-	HRCWH_SW_WATCHDOG_DISABLE | \
-	HRCWH_ROM_LOC_LOCAL_16BIT | \
-	HRCWH_BIG_ENDIAN | \
-	HRCWH_LALE_NORMAL)
+#define CONFIG_SYS_SICRL	SICRL_IRQ_CKS
 
 #define CONFIG_SYS_DDRCDR (\
 	DDRCDR_EN | \
@@ -120,21 +89,3 @@
 /* EEprom support */
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
 
-/*
- * Local Bus Configuration & Clock Setup
- */
-#define CONFIG_SYS_LCRR_DBYP	0x80000000
-#define CONFIG_SYS_LCRR_EADC	0x00010000
-#define CONFIG_SYS_LCRR_CLKDIV	0x00000002
-
-#define CONFIG_SYS_LBC_LBCR	0x00000000
-
-/*
- * MMU Setup
- */
-#define CONFIG_SYS_IBAT7L	(0)
-#define CONFIG_SYS_IBAT7U	(0)
-#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
-
-#endif /* __CONFIG_KM8321_COMMON_H */
diff --git a/include/configs/km/km-mpc8360.h b/include/configs/km/km-mpc8360.h
new file mode 100644
index 0000000000..8f26e059e9
--- /dev/null
+++ b/include/configs/km/km-mpc8360.h
@@ -0,0 +1,91 @@
+/* KMBEC FPGA (PRIO) */
+#define CONFIG_SYS_KMBEC_FPGA_BASE	0xE8000000
+#define CONFIG_SYS_KMBEC_FPGA_SIZE	64
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_QE			/* Has QE */
+
+/*
+ * QE UEC ethernet configuration
+ */
+#define CONFIG_UEC_ETH1		/* GETH1 */
+#define UEC_VERBOSE_DEBUG	1
+
+#define CONFIG_SYS_UEC1_UCC_NUM	3	/* UCC4 */
+#define CONFIG_SYS_UEC1_RX_CLK		QE_CLK_NONE /* not used in RMII Mode */
+#define CONFIG_SYS_UEC1_TX_CLK		QE_CLK17
+#define CONFIG_SYS_UEC1_ETH_TYPE	FAST_ETH
+#define CONFIG_SYS_UEC1_PHY_ADDR	0
+#define CONFIG_SYS_UEC1_INTERFACE_TYPE	PHY_INTERFACE_MODE_RMII
+#define CONFIG_SYS_UEC1_INTERFACE_SPEED	100
+
+/*
+ * System IO Setup
+ */
+#define CONFIG_SYS_SICRH		(SICRH_UC1EOBI | SICRH_UC2E1OBI)
+
+/**
+ * DDR RAM settings
+ */
+#define CONFIG_SYS_DDR_SDRAM_CFG (\
+	SDRAM_CFG_SDRAM_TYPE_DDR2 | \
+	SDRAM_CFG_SREN | \
+	SDRAM_CFG_HSE)
+
+#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000
+
+#define CONFIG_SYS_DDR_CLK_CNTL (\
+	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
+
+#define CONFIG_SYS_DDR_INTERVAL (\
+	(0x080 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
+	(0x203 << SDRAM_INTERVAL_REFINT_SHIFT))
+
+#define CONFIG_SYS_DDR_CS0_BNDS			0x0000007f
+
+#define CONFIG_SYS_DDRCDR (\
+	DDRCDR_EN | \
+	DDRCDR_Q_DRN)
+#define CONFIG_SYS_DDR_MODE		0x47860452
+#define CONFIG_SYS_DDR_MODE2		0x8080c000
+
+#define CONFIG_SYS_DDR_TIMING_0 (\
+	(2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
+	(8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
+	(6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
+	(2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
+	(0 << TIMING_CFG0_WWT_SHIFT) | \
+	(0 << TIMING_CFG0_RRT_SHIFT) | \
+	(0 << TIMING_CFG0_WRT_SHIFT) | \
+	(0 << TIMING_CFG0_RWT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_1	((TIMING_CFG1_CASLAT_50) | \
+				 (2 << TIMING_CFG1_WRTORD_SHIFT) | \
+				 (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
+				 (3 << TIMING_CFG1_WRREC_SHIFT) | \
+				 (7 << TIMING_CFG1_REFREC_SHIFT) | \
+				 (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
+				 (8 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
+				 (3 << TIMING_CFG1_PRETOACT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_2 (\
+	(0xa << TIMING_CFG2_FOUR_ACT_SHIFT) | \
+	(3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
+	(2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
+	(2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
+	(4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
+	(5 << TIMING_CFG2_CPO_SHIFT) | \
+	(0 << TIMING_CFG2_ADD_LAT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_3			0x00000000
+
+/* EEprom support */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
+
+/*
+ * PAXE on the local bus CS3
+ */
+#define CONFIG_SYS_PAXE_BASE		0xA0000000
+#define CONFIG_SYS_PAXE_SIZE		256
diff --git a/include/configs/km/km-mpc83xx.h b/include/configs/km/km-mpc83xx.h
new file mode 100644
index 0000000000..455e5236de
--- /dev/null
+++ b/include/configs/km/km-mpc83xx.h
@@ -0,0 +1,160 @@
+/*
+ * Internal Definitions
+ */
+#define BOOTFLASH_START	0xF0000000
+
+#define CONFIG_KM_CONSOLE_TTY	"ttyS0"
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_SYS_SDRAM_BASE		0x00000000 /* DDR is system memory */
+#define CONFIG_SYS_SDRAM_BASE2	(CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */
+
+#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN | \
+					DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
+
+#define CFG_83XX_DDR_USES_CS0
+
+/*
+ * Manually set up DDR parameters
+ */
+#define CONFIG_DDR_II
+#define CONFIG_SYS_DDR_SIZE		2048 /* MB */
+
+/*
+ * The reserved memory
+ */
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE /* start of monitor */
+#define CONFIG_SYS_FLASH_BASE		0xF0000000
+
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+/* Reserve 768 kB for Mon */
+#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
+
+/*
+ * Initial RAM Base Address Setup
+ */
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_SIZE	0x1000 /* End of used area in RAM */
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
+						GENERATED_GBL_DATA_SIZE)
+/*
+ * Init Local Bus Memory Controller:
+ *
+ * Bank Bus     Machine PortSz  Size  Device
+ * ---- ---     ------- ------  -----  ------
+ *  0   Local   GPCM    16 bit  256MB FLASH
+ *  1   Local   GPCM     8 bit  128MB GPIO/PIGGY
+ *
+ */
+
+/*
+ * FLASH on the Local Bus
+ */
+#define CONFIG_SYS_FLASH_SIZE		256 /* max FLASH size is 256M */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	1   /* max num of flash banks	*/
+#define CONFIG_SYS_MAX_FLASH_SECT	512 /* max num of sects on one chip */
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
+
+/*
+ * Serial Port
+ */
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
+
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR + 0x4500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR + 0x4600)
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_NUM_I2C_BUSES	4
+#define CONFIG_SYS_I2C_MAX_HOPS		1
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED	200000
+#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
+#define CONFIG_SYS_I2C_OFFSET		0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED	200000
+#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
+#define CONFIG_SYS_I2C_BUSES	{{0, {I2C_NULL_HOP} }, \
+		{0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
+		{0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
+		{1, {I2C_NULL_HOP} } }
+
+#define CONFIG_KM_IVM_BUS		2	/* I2C2 (Mux-Port 1)*/
+
+#if defined(CONFIG_CMD_NAND)
+#define CONFIG_NAND_KMETER1
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_SYS_NAND_BASE		CONFIG_SYS_KMBEC_FPGA_BASE
+#endif
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)
+
+/*
+ * Environment
+ */
+
+#ifndef CONFIG_SYS_RAMBOOT
+#ifndef CONFIG_ENV_ADDR
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + \
+					CONFIG_SYS_MONITOR_LEN)
+#endif
+#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K(one sector) for env */
+#ifndef CONFIG_ENV_OFFSET
+#define CONFIG_ENV_OFFSET	(CONFIG_SYS_MONITOR_LEN)
+#endif
+
+/* Address and size of Redundant Environment Sector	*/
+#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + \
+						CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
+
+#else /* CFG_SYS_RAMBOOT */
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
+#define CONFIG_ENV_SIZE		0x2000
+#endif /* CFG_SYS_RAMBOOT */
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_OVERWRITE
+#ifndef CONFIG_KM_DEF_ENV		/* if not set by keymile-common.h */
+#define CONFIG_KM_DEF_ENV "km-common=empty\0"
+#endif
+
+#ifndef CONFIG_KM_DEF_ARCH
+#define CONFIG_KM_DEF_ARCH	"arch=ppc_82xx\0"
+#endif
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	CONFIG_KM_DEF_ENV						 \
+	CONFIG_KM_DEF_ARCH						 \
+	"newenv="							 \
+		"prot off " __stringify(CONFIG_ENV_ADDR) " +0x40000 && " \
+		"era " __stringify(CONFIG_ENV_ADDR) " +0x40000\0"	 \
+	"unlock=yes\0"							 \
+	""
+
+#if defined(CONFIG_UEC_ETH)
+#define CONFIG_HAS_ETH0
+#endif
+
+/*
+ * QE UEC ethernet configuration
+ */
+#define CONFIG_UEC_ETH
+#define CONFIG_ETHPRIME		"UEC0"
diff --git a/include/configs/km/km83xx-common.h b/include/configs/km/km83xx-common.h
deleted file mode 100644
index a76f606e3e..0000000000
--- a/include/configs/km/km83xx-common.h
+++ /dev/null
@@ -1,296 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2010
- * Heiko Schocher, DENX Software Engineering, hs@denx.de.
- */
-
-#ifndef __CONFIG_KM83XX_H
-#define __CONFIG_KM83XX_H
-
-/* include common defines/options for all Keymile boards */
-#include "keymile-common.h"
-#include "km-powerpc.h"
-
-/*
- * System Clock Setup
- */
-#define CONFIG_83XX_CLKIN		66000000
-#define CONFIG_SYS_CLK_FREQ		66000000
-#define CONFIG_83XX_PCICLK		66000000
-
-/*
- * IMMR new address
- */
-#define CONFIG_SYS_IMMR		0xE0000000
-
-/*
- * Bus Arbitration Configuration Register (ACR)
- */
-#define CONFIG_SYS_ACR_PIPE_DEP 3       /* pipeline depth 4 transactions */
-#define CONFIG_SYS_ACR_RPTCNT   3       /* 4 consecutive transactions */
-#define CONFIG_SYS_ACR_APARK    0       /* park bus to master (below) */
-#define CONFIG_SYS_ACR_PARKM    3       /* parking master = QuiccEngine */
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_DDR_BASE		0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_SDRAM_BASE2	(CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */
-
-#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN | \
-					DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-
-#define CFG_83XX_DDR_USES_CS0
-
-/*
- * Manually set up DDR parameters
- */
-#define CONFIG_DDR_II
-#define CONFIG_SYS_DDR_SIZE		2048 /* MB */
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE /* start of monitor */
-#define CONFIG_SYS_FLASH_BASE		0xF0000000
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-/* Reserve 768 kB for Mon */
-#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE	0x1000 /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
-						GENERATED_GBL_DATA_SIZE)
-
-/*
- * Init Local Bus Memory Controller:
- *
- * Bank Bus     Machine PortSz  Size  Device
- * ---- ---     ------- ------  -----  ------
- *  0   Local   GPCM    16 bit  256MB FLASH
- *  1   Local   GPCM     8 bit  128MB GPIO/PIGGY
- *
- */
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_SIZE		256 /* max FLASH size is 256M */
-
-#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_256MB)
-
-#define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE | \
-				BR_PS_16 | /* 16 bit port size */ \
-				BR_MS_GPCM | /* MSEL = GPCM */ \
-				BR_V)
-
-#define CONFIG_SYS_OR0_PRELIM	(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) | \
-				OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \
-				OR_GPCM_SCY_5 | \
-				OR_GPCM_TRLX_SET | OR_GPCM_EAD)
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	1   /* max num of flash banks	*/
-#define CONFIG_SYS_MAX_FLASH_SECT	512 /* max num of sects on one chip */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-
-/*
- * PRIO1/PIGGY on the local bus CS1
- */
-/* Window base at flash base */
-#define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_KMBEC_FPGA_BASE
-#define CONFIG_SYS_LBLAWAR1_PRELIM	(LBLAWAR_EN | LBLAWAR_128MB)
-
-#define CONFIG_SYS_BR1_PRELIM	(CONFIG_SYS_KMBEC_FPGA_BASE | \
-				BR_PS_8 | /* 8 bit port size */ \
-				BR_MS_GPCM | /* MSEL = GPCM */ \
-				BR_V)
-#define CONFIG_SYS_OR1_PRELIM	(MEG_TO_AM(CONFIG_SYS_KMBEC_FPGA_SIZE) | \
-				OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \
-				OR_GPCM_SCY_2 | \
-				OR_GPCM_TRLX_SET | OR_GPCM_EAD)
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
-
-#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR+0x4600)
-
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME		"UEC0"
-
-#if !defined(CONFIG_MPC8309)
-#define CONFIG_UEC_ETH1		/* GETH1 */
-#define UEC_VERBOSE_DEBUG	1
-#endif
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM	3	/* UCC4 */
-#define CONFIG_SYS_UEC1_RX_CLK		QE_CLK_NONE /* not used in RMII Mode */
-#define CONFIG_SYS_UEC1_TX_CLK		QE_CLK17
-#define CONFIG_SYS_UEC1_ETH_TYPE	FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR	0
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE	PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED	100
-#endif
-
-/*
- * Environment
- */
-
-#ifndef CONFIG_SYS_RAMBOOT
-#ifndef CONFIG_ENV_ADDR
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + \
-					CONFIG_SYS_MONITOR_LEN)
-#endif
-#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K(one sector) for env */
-#ifndef CONFIG_ENV_OFFSET
-#define CONFIG_ENV_OFFSET	(CONFIG_SYS_MONITOR_LEN)
-#endif
-
-/* Address and size of Redundant Environment Sector	*/
-#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + \
-						CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-
-#else /* CFG_SYS_RAMBOOT */
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
-#define CONFIG_ENV_SIZE		0x2000
-#endif /* CFG_SYS_RAMBOOT */
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_NUM_I2C_BUSES	4
-#define CONFIG_SYS_I2C_MAX_HOPS		1
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED	200000
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
-#define CONFIG_SYS_I2C_OFFSET		0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED	200000
-#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
-#define CONFIG_SYS_I2C_BUSES	{{0, {I2C_NULL_HOP} }, \
-		{0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
-		{0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
-		{1, {I2C_NULL_HOP} } }
-
-#define CONFIG_KM_IVM_BUS		2	/* I2C2 (Mux-Port 1)*/
-
-#if defined(CONFIG_CMD_NAND)
-#define CONFIG_NAND_KMETER1
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_SYS_NAND_BASE		CONFIG_SYS_KMBEC_FPGA_BASE
-#endif
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)
-
-/*
- * Core HID Setup
- */
-#define CONFIG_SYS_HID0_INIT		0x000000000
-#define CONFIG_SYS_HID0_FINAL		(HID0_ENABLE_MACHINE_CHECK | \
-					 HID0_ENABLE_INSTRUCTION_CACHE)
-#define CONFIG_SYS_HID2			HID2_HBE
-
-/*
- * MMU Setup
- */
-
-#define CONFIG_HIGH_BATS	1	/* High BATs supported */
-
-/* DDR: cache cacheable */
-#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \
-				BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | \
-					BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
-
-/* IMMRBAR & PCI IO: cache-inhibit and guarded */
-#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_IMMR | BATL_PP_RW | \
-				BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_IMMR | BATU_BL_4M | BATU_VS \
-					| BATU_VP)
-#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
-
-/* PRIO1, PIGGY:  icache cacheable, but dcache-inhibit and guarded */
-#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_KMBEC_FPGA_BASE | BATL_PP_RW | \
-				BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_KMBEC_FPGA_BASE | BATU_BL_128M | \
-				BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT2L	(CONFIG_SYS_KMBEC_FPGA_BASE | BATL_PP_RW | \
-				 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
-
-/* FLASH: icache cacheable, but dcache-inhibit and guarded */
-#define CONFIG_SYS_IBAT3L	(CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
-					BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT3U	(CONFIG_SYS_FLASH_BASE | BATU_BL_256M | \
-					BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT3L	(CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
-				 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
-
-/* Stack in dcache: cacheable, no memory coherence */
-#define CONFIG_SYS_IBAT4L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
-#define CONFIG_SYS_IBAT4U	(CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
-					BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT4L	CONFIG_SYS_IBAT4L
-#define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U
-
-/*
- * Internal Definitions
- */
-#define BOOTFLASH_START	0xF0000000
-
-#define CONFIG_KM_CONSOLE_TTY	"ttyS0"
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_OVERWRITE
-#ifndef CONFIG_KM_DEF_ENV		/* if not set by keymile-common.h */
-#define CONFIG_KM_DEF_ENV "km-common=empty\0"
-#endif
-
-#ifndef CONFIG_KM_DEF_ARCH
-#define CONFIG_KM_DEF_ARCH	"arch=ppc_82xx\0"
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
-	CONFIG_KM_DEF_ENV						\
-	CONFIG_KM_DEF_ARCH						\
-	"newenv="							\
-		"prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && "	\
-		"era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0"		\
-	"unlock=yes\0"							\
-	""
-
-#if defined(CONFIG_UEC_ETH)
-#define CONFIG_HAS_ETH0
-#endif
-
-#endif /* __CONFIG_KM83XX_H */
diff --git a/include/configs/km8360.h b/include/configs/km8360.h
deleted file mode 100644
index feb8a9a16d..0000000000
--- a/include/configs/km8360.h
+++ /dev/null
@@ -1,271 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2012
- * Holger Brunck, Keymile GmbH Hannover, <holger.brunck@keymile.com>
- * Christian Herzig, Keymile AG Switzerland, <christian.herzig@keymile.com>
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/* KMBEC FPGA (PRIO) */
-#define CONFIG_SYS_KMBEC_FPGA_BASE	0xE8000000
-#define CONFIG_SYS_KMBEC_FPGA_SIZE	64
-
-#if defined CONFIG_KMETER1
-#define CONFIG_HOSTNAME		"kmeter1"
-#define CONFIG_KM_BOARD_NAME   "kmeter1"
-#define CONFIG_KM_DEF_NETDEV	"netdev=eth2\0"
-#elif defined CONFIG_KMCOGE5NE
-#define CONFIG_HOSTNAME		"kmcoge5ne"
-#define CONFIG_KM_BOARD_NAME	"kmcoge5ne"
-#define CONFIG_KM_DEF_NETDEV	"netdev=eth1\0"
-#define CONFIG_NAND_ECC_BCH
-#define CONFIG_NAND_KMETER1
-#define CONFIG_SYS_MAX_NAND_DEVICE		1
-#define NAND_MAX_CHIPS				1
-#define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE /* PRIO_BASE_ADDRESS */
-
-#define CONFIG_KM_UBI_PARTITION_NAME_BOOT	"ubi0"
-#define CONFIG_KM_UBI_PARTITION_NAME_APP	"ubi1"
-#else
-#error ("Board not supported")
-#endif
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_QE			/* Has QE */
-#define CONFIG_MPC8360			/* MPC8360 CPU specific */
-
-/* include common defines/options for all 83xx Keymile boards */
-#include "km/km83xx-common.h"
-
-/*
- * System IO Setup
- */
-#define CONFIG_SYS_SICRH		(SICRH_UC1EOBI | SICRH_UC2E1OBI)
-
-/*
- * Hardware Reset Configuration Word
- */
-#define CONFIG_SYS_HRCW_LOW (\
-	HRCWL_CSB_TO_CLKIN_4X1 | \
-	HRCWL_CORE_TO_CSB_2X1 | \
-	HRCWL_CE_PLL_VCO_DIV_2 | \
-	HRCWL_CE_TO_PLL_1X6)
-
-#define CONFIG_SYS_HRCW_HIGH (\
-	HRCWH_CORE_ENABLE | \
-	HRCWH_FROM_0X00000100 | \
-	HRCWH_BOOTSEQ_DISABLE | \
-	HRCWH_SW_WATCHDOG_DISABLE | \
-	HRCWH_ROM_LOC_LOCAL_16BIT | \
-	HRCWH_BIG_ENDIAN | \
-	HRCWH_LALE_EARLY | \
-	HRCWH_LDP_CLEAR)
-
-/**
- * DDR RAM settings
- */
-#define CONFIG_SYS_DDR_SDRAM_CFG (\
-	SDRAM_CFG_SDRAM_TYPE_DDR2 | \
-	SDRAM_CFG_SREN | \
-	SDRAM_CFG_HSE)
-
-#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000
-
-#ifdef CONFIG_KMCOGE5NE
-/**
- * KMCOGE5NE has 512 MB RAM
- */
-#define CONFIG_SYS_DDR_CS0_CONFIG (\
-	CSCONFIG_EN | \
-	CSCONFIG_AP | \
-	CSCONFIG_ODT_WR_ONLY_CURRENT | \
-	CSCONFIG_BANK_BIT_3 | \
-	CSCONFIG_ROW_BIT_13 | \
-	CSCONFIG_COL_BIT_10)
-#else
-#define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN | CSCONFIG_AP | \
-					 CSCONFIG_ROW_BIT_13 | \
-					 CSCONFIG_COL_BIT_10 | \
-					 CSCONFIG_ODT_WR_ONLY_CURRENT)
-#endif
-
-#define CONFIG_SYS_DDR_CLK_CNTL (\
-	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-
-#define CONFIG_SYS_DDR_INTERVAL (\
-	(0x080 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
-	(0x203 << SDRAM_INTERVAL_REFINT_SHIFT))
-
-#define CONFIG_SYS_DDR_CS0_BNDS			0x0000007f
-
-#define CONFIG_SYS_DDRCDR (\
-	DDRCDR_EN | \
-	DDRCDR_Q_DRN)
-#define CONFIG_SYS_DDR_MODE		0x47860452
-#define CONFIG_SYS_DDR_MODE2		0x8080c000
-
-#define CONFIG_SYS_DDR_TIMING_0 (\
-	(2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
-	(8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
-	(6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
-	(2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
-	(0 << TIMING_CFG0_WWT_SHIFT) | \
-	(0 << TIMING_CFG0_RRT_SHIFT) | \
-	(0 << TIMING_CFG0_WRT_SHIFT) | \
-	(0 << TIMING_CFG0_RWT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_1	((TIMING_CFG1_CASLAT_50) | \
-				 (2 << TIMING_CFG1_WRTORD_SHIFT) | \
-				 (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
-				 (3 << TIMING_CFG1_WRREC_SHIFT) | \
-				 (7 << TIMING_CFG1_REFREC_SHIFT) | \
-				 (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
-				 (8 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
-				 (3 << TIMING_CFG1_PRETOACT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_2 (\
-	(0xa << TIMING_CFG2_FOUR_ACT_SHIFT) | \
-	(3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
-	(2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
-	(2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
-	(4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
-	(5 << TIMING_CFG2_CPO_SHIFT) | \
-	(0 << TIMING_CFG2_ADD_LAT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_3			0x00000000
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
-
-/*
- * Local Bus Configuration & Clock Setup
- */
-#define CONFIG_SYS_LCRR_DBYP		LCRR_DBYP
-#define CONFIG_SYS_LCRR_EADC		LCRR_EADC_2
-#define CONFIG_SYS_LCRR_CLKDIV		LCRR_CLKDIV_4
-
-/*
- * PAXE on the local bus CS3
- */
-#define CONFIG_SYS_PAXE_BASE		0xA0000000
-#define CONFIG_SYS_PAXE_SIZE		256
-
-#define CONFIG_SYS_LBLAWBAR3_PRELIM	CONFIG_SYS_PAXE_BASE
-
-#define CONFIG_SYS_LBLAWAR3_PRELIM	0x8000001C /* 512MB window size */
-
-#define CONFIG_SYS_BR3_PRELIM (\
-	CONFIG_SYS_PAXE_BASE | \
-	(1 << BR_PS_SHIFT) | \
-	BR_V)
-
-#define CONFIG_SYS_OR3_PRELIM (\
-	MEG_TO_AM(CONFIG_SYS_PAXE_SIZE) | \
-	OR_GPCM_CSNT | \
-	OR_GPCM_ACS_DIV2 | \
-	OR_GPCM_SCY_2 | \
-	OR_GPCM_TRLX | \
-	OR_GPCM_EAD)
-
-#ifdef CONFIG_KMCOGE5NE
-/*
- * BFTIC3 on the local bus CS4
- */
-#define CONFIG_SYS_BFTIC3_BASE			0xB0000000
-#define CONFIG_SYS_BFTIC3_SIZE			256
-
-#define CONFIG_SYS_BR4_PRELIM (\
-	CONFIG_SYS_BFTIC3_BASE |\
-	(1 << BR_PS_SHIFT) | \
-	BR_V)
-
-#define CONFIG_SYS_OR4_PRELIM (\
-	MEG_TO_AM(CONFIG_SYS_BFTIC3_SIZE) |\
-	OR_GPCM_CSNT | \
-	OR_GPCM_ACS_DIV2 |\
-	OR_GPCM_SCY_2 |\
-	OR_GPCM_TRLX |\
-	OR_GPCM_EAD)
-#endif
-
-/*
- * MMU Setup
- */
-
-/* PAXE:  icache cacheable, but dcache-inhibit and guarded */
-#define CONFIG_SYS_IBAT5L (\
-	CONFIG_SYS_PAXE_BASE | \
-	BATL_PP_10 | \
-	BATL_MEMCOHERENCE)
-
-#define CONFIG_SYS_IBAT5U (\
-	CONFIG_SYS_PAXE_BASE | \
-	BATU_BL_256M | \
-	BATU_VS | \
-	BATU_VP)
-
-#define CONFIG_SYS_DBAT5L (\
-	CONFIG_SYS_PAXE_BASE | \
-	BATL_PP_10 | \
-	BATL_CACHEINHIBIT | \
-	BATL_GUARDEDSTORAGE)
-
-#define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
-
-#ifdef CONFIG_KMCOGE5NE
-/* BFTIC3:  icache cacheable, but dcache-inhibit and guarded */
-#define CONFIG_SYS_IBAT6L (\
-	CONFIG_SYS_BFTIC3_BASE | \
-	BATL_PP_10 | \
-	BATL_MEMCOHERENCE)
-
-#define CONFIG_SYS_IBAT6U (\
-	CONFIG_SYS_BFTIC3_BASE | \
-	BATU_BL_256M | \
-	BATU_VS | \
-	BATU_VP)
-
-#define CONFIG_SYS_DBAT6L (\
-	CONFIG_SYS_BFTIC3_BASE | \
-	BATL_PP_10 | \
-	BATL_CACHEINHIBIT | \
-	BATL_GUARDEDSTORAGE)
-
-#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
-
-/* DDR/LBC SDRAM next 256M: cacheable */
-#define CONFIG_SYS_IBAT7L (\
-	CONFIG_SYS_SDRAM_BASE2 |\
-	BATL_PP_10 |\
-	BATL_CACHEINHIBIT |\
-	BATL_GUARDEDSTORAGE)
-
-#define CONFIG_SYS_IBAT7U (\
-	CONFIG_SYS_SDRAM_BASE2 |\
-	BATU_BL_256M |\
-	BATU_VS |\
-	BATU_VP)
-/* enable POST tests */
-#define CONFIG_POST (CONFIG_SYS_POST_MEMORY|CONFIG_SYS_POST_MEM_REGIONS)
-#define CONFIG_POST_EXTERNAL_WORD_FUNCS /* use own functions, not generic */
-#define CPM_POST_WORD_ADDR  CONFIG_SYS_MEMTEST_END
-#define CONFIG_TESTPIN_REG  gprt3	/* for kmcoge5ne */
-#define CONFIG_TESTPIN_MASK 0x20	/* for kmcoge5ne */
-
-#else
-#define CONFIG_SYS_IBAT6L	(0)
-#define CONFIG_SYS_IBAT6U	(0)
-#define CONFIG_SYS_IBAT7L	(0)
-#define CONFIG_SYS_IBAT7U	(0)
-#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
-#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
-#endif
-
-#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
-
-#endif /* CONFIG */
diff --git a/include/configs/kmcoge5ne.h b/include/configs/kmcoge5ne.h
new file mode 100644
index 0000000000..fc78b27cbb
--- /dev/null
+++ b/include/configs/kmcoge5ne.h
@@ -0,0 +1,60 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * (C) Copyright 2012
+ * Holger Brunck, Keymile GmbH Hannover, <holger.brunck@keymile.com>
+ * Christian Herzig, Keymile AG Switzerland, <christian.herzig@keymile.com>
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_HOSTNAME		"kmcoge5ne"
+#define CONFIG_KM_BOARD_NAME	"kmcoge5ne"
+#define CONFIG_KM_DEF_NETDEV	"netdev=eth1\0"
+#define CONFIG_NAND_ECC_BCH
+#define CONFIG_NAND_KMETER1
+#define CONFIG_SYS_MAX_NAND_DEVICE		1
+#define NAND_MAX_CHIPS				1
+#define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE /* PRIO_BASE_ADDRESS */
+
+#define CONFIG_KM_UBI_PARTITION_NAME_BOOT	"ubi0"
+#define CONFIG_KM_UBI_PARTITION_NAME_APP	"ubi1"
+
+/* include common defines/options for all Keymile boards */
+#include "km/keymile-common.h"
+#include "km/km-powerpc.h"
+#include "km/km-mpc83xx.h"
+#include "km/km-mpc8360.h"
+
+/*
+ * System Clock Setup
+ */
+#define CONFIG_83XX_CLKIN		66000000
+#define CONFIG_SYS_CLK_FREQ		66000000
+#define CONFIG_83XX_PCICLK		66000000
+
+/**
+ * KMCOGE5NE has 512 MB RAM
+ */
+#define CONFIG_SYS_DDR_CS0_CONFIG (\
+	CSCONFIG_EN | \
+	CSCONFIG_AP | \
+	CSCONFIG_ODT_WR_ONLY_CURRENT | \
+	CSCONFIG_BANK_BIT_3 | \
+	CSCONFIG_ROW_BIT_13 | \
+	CSCONFIG_COL_BIT_10)
+
+/*
+ * BFTIC3 on the local bus CS4
+ */
+#define CONFIG_SYS_BFTIC3_BASE			0xB0000000
+#define CONFIG_SYS_BFTIC3_SIZE			256
+
+/* enable POST tests */
+#define CONFIG_POST (CONFIG_SYS_POST_MEMORY|CONFIG_SYS_POST_MEM_REGIONS)
+#define CONFIG_POST_EXTERNAL_WORD_FUNCS /* use own functions, not generic */
+#define CPM_POST_WORD_ADDR  CONFIG_SYS_MEMTEST_END
+#define CONFIG_TESTPIN_REG  gprt3	/* for kmcoge5ne */
+#define CONFIG_TESTPIN_MASK 0x20	/* for kmcoge5ne */
+
+#endif /* CONFIG */
diff --git a/include/configs/kmeter1.h b/include/configs/kmeter1.h
new file mode 100644
index 0000000000..bfa7ca27c7
--- /dev/null
+++ b/include/configs/kmeter1.h
@@ -0,0 +1,30 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * (C) Copyright 2012
+ * Holger Brunck, Keymile GmbH Hannover, <holger.brunck@keymile.com>
+ * Christian Herzig, Keymile AG Switzerland, <christian.herzig@keymile.com>
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_HOSTNAME		"kmeter1"
+#define CONFIG_KM_BOARD_NAME   "kmeter1"
+#define CONFIG_KM_DEF_NETDEV	"netdev=eth2\0"
+
+/* include common defines/options for all Keymile boards */
+#include "km/keymile-common.h"
+#include "km/km-powerpc.h"
+#include "km/km-mpc83xx.h"
+#include "km/km-mpc8360.h"
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX	1
+
+#define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN | CSCONFIG_AP | \
+					 CSCONFIG_ROW_BIT_13 | \
+					 CSCONFIG_COL_BIT_10 | \
+					 CSCONFIG_ODT_WR_ONLY_CURRENT)
+#endif /* CONFIG */
diff --git a/include/configs/kmopti2.h b/include/configs/kmopti2.h
new file mode 100644
index 0000000000..67e864fc98
--- /dev/null
+++ b/include/configs/kmopti2.h
@@ -0,0 +1,35 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2006 Freescale Semiconductor, Inc.
+ *                    Dave Liu <daveliu@freescale.com>
+ *
+ * Copyright (C) 2007 Logic Product Development, Inc.
+ *                    Peter Barada <peterb@logicpd.com>
+ *
+ * Copyright (C) 2007 MontaVista Software, Inc.
+ *                    Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * (C) Copyright 2008
+ * Heiko Schocher, DENX Software Engineering, hs@denx.de.
+ *
+ * (C) Copyright 2010-2013
+ * Lukas Roggli, KEYMILE Ltd, lukas.roggli@keymile.com
+ * Holger Brunck,  Keymile GmbH, holger.bruncl@keymile.com
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_KM_BOARD_NAME	"kmopti2"
+#define CONFIG_HOSTNAME		"kmopti2"
+
+/* include common defines/options for all Keymile boards */
+#include "km/keymile-common.h"
+#include "km/km-powerpc.h"
+#include "km/km-mpc83xx.h"
+#include "km/km-mpc832x.h"
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/kmsupx5.h b/include/configs/kmsupx5.h
new file mode 100644
index 0000000000..ba33e6074b
--- /dev/null
+++ b/include/configs/kmsupx5.h
@@ -0,0 +1,35 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2006 Freescale Semiconductor, Inc.
+ *                    Dave Liu <daveliu@freescale.com>
+ *
+ * Copyright (C) 2007 Logic Product Development, Inc.
+ *                    Peter Barada <peterb@logicpd.com>
+ *
+ * Copyright (C) 2007 MontaVista Software, Inc.
+ *                    Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * (C) Copyright 2008
+ * Heiko Schocher, DENX Software Engineering, hs@denx.de.
+ *
+ * (C) Copyright 2010-2013
+ * Lukas Roggli, KEYMILE Ltd, lukas.roggli@keymile.com
+ * Holger Brunck,  Keymile GmbH, holger.bruncl@keymile.com
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_KM_BOARD_NAME	"kmsupx5"
+#define CONFIG_HOSTNAME		"kmsupx5"
+
+/* include common defines/options for all Keymile boards */
+#include "km/keymile-common.h"
+#include "km/km-powerpc.h"
+#include "km/km-mpc83xx.h"
+#include "km/km-mpc832x.h"
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/kmtegr1.h b/include/configs/kmtegr1.h
new file mode 100644
index 0000000000..701eb53f63
--- /dev/null
+++ b/include/configs/kmtegr1.h
@@ -0,0 +1,45 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2006 Freescale Semiconductor, Inc.
+ *                    Dave Liu <daveliu@freescale.com>
+ *
+ * Copyright (C) 2007 Logic Product Development, Inc.
+ *                    Peter Barada <peterb@logicpd.com>
+ *
+ * Copyright (C) 2007 MontaVista Software, Inc.
+ *                    Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * (C) Copyright 2010
+ * Heiko Schocher, DENX Software Engineering, hs@denx.de.
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+
+#define CONFIG_HOSTNAME   "kmtegr1"
+#define CONFIG_KM_BOARD_NAME   "kmtegr1"
+#define CONFIG_KM_UBI_PARTITION_NAME_BOOT	"ubi0"
+#define CONFIG_KM_UBI_PARTITION_NAME_APP	"ubi1"
+
+#define CONFIG_ENV_ADDR		0xF0100000
+#define CONFIG_ENV_OFFSET	0x100000
+
+#define CONFIG_NAND_ECC_BCH
+#define CONFIG_NAND_KMETER1
+#define CONFIG_SYS_MAX_NAND_DEVICE		1
+#define NAND_MAX_CHIPS				1
+
+/* include common defines/options for all Keymile boards */
+#include "km/keymile-common.h"
+#include "km/km-powerpc.h"
+#include "km/km-mpc83xx.h"
+#include "km/km-mpc8309.h"
+
+/* must be after the include because KMBEC_FPGA is otherwise undefined */
+#define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE /* PRIO_BASE_ADDRESS */
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/kmtepr2.h b/include/configs/kmtepr2.h
new file mode 100644
index 0000000000..e0c907d11a
--- /dev/null
+++ b/include/configs/kmtepr2.h
@@ -0,0 +1,35 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2006 Freescale Semiconductor, Inc.
+ *                    Dave Liu <daveliu@freescale.com>
+ *
+ * Copyright (C) 2007 Logic Product Development, Inc.
+ *                    Peter Barada <peterb@logicpd.com>
+ *
+ * Copyright (C) 2007 MontaVista Software, Inc.
+ *                    Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * (C) Copyright 2008
+ * Heiko Schocher, DENX Software Engineering, hs@denx.de.
+ *
+ * (C) Copyright 2010-2013
+ * Lukas Roggli, KEYMILE Ltd, lukas.roggli@keymile.com
+ * Holger Brunck,  Keymile GmbH, holger.bruncl@keymile.com
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_KM_BOARD_NAME    "kmtepr2"
+#define CONFIG_HOSTNAME         "kmtepr2"
+
+/* include common defines/options for all Keymile boards */
+#include "km/keymile-common.h"
+#include "km/km-powerpc.h"
+#include "km/km-mpc83xx.h"
+#include "km/km-mpc832x.h"
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/kmvect1.h b/include/configs/kmvect1.h
new file mode 100644
index 0000000000..6e5d50700c
--- /dev/null
+++ b/include/configs/kmvect1.h
@@ -0,0 +1,61 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2006 Freescale Semiconductor, Inc.
+ *                    Dave Liu <daveliu@freescale.com>
+ *
+ * Copyright (C) 2007 Logic Product Development, Inc.
+ *                    Peter Barada <peterb@logicpd.com>
+ *
+ * Copyright (C) 2007 MontaVista Software, Inc.
+ *                    Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * (C) Copyright 2010
+ * Heiko Schocher, DENX Software Engineering, hs@denx.de.
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+
+#define CONFIG_HOSTNAME		"kmvect1"
+#define CONFIG_KM_BOARD_NAME   "kmvect1"
+/* at end of uboot partition, before env */
+#define CONFIG_SYS_QE_FW_ADDR   0xF00B0000
+
+/* include common defines/options for all Keymile boards */
+#include "km/keymile-common.h"
+#include "km/km-powerpc.h"
+#include "km/km-mpc83xx.h"
+#include "km/km-mpc8309.h"
+
+#define CONFIG_SYS_MAMR	(MxMR_GPL_x4DIS | \
+			 0x0000c000 | \
+			 MxMR_WLFx_2X)
+/*
+ * QE UEC ethernet configuration
+ */
+#define CONFIG_MV88E6352_SWITCH
+#define CONFIG_KM_MVEXTSW_ADDR		0x10
+
+/* ethernet port connected to simple switch 88e6122 (UEC0) */
+#define CONFIG_UEC_ETH1
+#define CONFIG_SYS_UEC1_UCC_NUM		0	/* UCC1 */
+#define CONFIG_SYS_UEC1_RX_CLK		QE_CLK9
+#define CONFIG_SYS_UEC1_TX_CLK		QE_CLK10
+
+#define CONFIG_FIXED_PHY		0xFFFFFFFF
+#define CONFIG_SYS_FIXED_PHY_ADDR	0x1E	/* unused address */
+#define CONFIG_SYS_FIXED_PHY_PORT(devnum, speed, duplex) \
+		{devnum, speed, duplex}
+#define CONFIG_SYS_FIXED_PHY_PORTS \
+		CONFIG_SYS_FIXED_PHY_PORT("UEC0", SPEED_100, DUPLEX_FULL)
+
+#define CONFIG_SYS_UEC1_ETH_TYPE	FAST_ETH
+#define CONFIG_SYS_UEC1_PHY_ADDR	CONFIG_SYS_FIXED_PHY_ADDR
+#define CONFIG_SYS_UEC1_INTERFACE_TYPE	PHY_INTERFACE_MODE_MII
+#define CONFIG_SYS_UEC1_INTERFACE_SPEED	100
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/mpc8308_p1m.h b/include/configs/mpc8308_p1m.h
index 98f030388c..3ce4b705b7 100644
--- a/include/configs/mpc8308_p1m.h
+++ b/include/configs/mpc8308_p1m.h
@@ -12,8 +12,6 @@
  * High Level Configuration Options
  */
 #define CONFIG_E300		1 /* E300 family */
-#define CONFIG_MPC830x		1 /* MPC830x family */
-#define CONFIG_MPC8308		1 /* MPC8308 CPU specific */
 
 /*
  * On-board devices
@@ -23,69 +21,6 @@
 #define CONFIG_TSEC1
 #define CONFIG_TSEC2
 
-/*
- * System Clock Setup
- */
-#define CONFIG_83XX_CLKIN	33333333 /* in Hz */
-#define CONFIG_SYS_CLK_FREQ	CONFIG_83XX_CLKIN
-
-/*
- * Hardware Reset Configuration Word
- * if CLKIN is 66.66MHz, then
- * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz
- * We choose the A type silicon as default, so the core is 400Mhz.
- */
-#define CONFIG_SYS_HRCW_LOW (\
-	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
-	HRCWL_DDR_TO_SCB_CLK_2X1 |\
-	HRCWL_SVCOD_DIV_2 |\
-	HRCWL_CSB_TO_CLKIN_4X1 |\
-	HRCWL_CORE_TO_CSB_3X1)
-/*
- * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits
- * in 8308's HRCWH according to the manual, but original Freescale's
- * code has them and I've expirienced some problems using the board
- * with BDI3000 attached when I've tried to set these bits to zero
- * (UART doesn't work after the 'reset run' command).
- */
-#define CONFIG_SYS_HRCW_HIGH (\
-	HRCWH_PCI_HOST |\
-	HRCWH_PCI1_ARBITER_ENABLE |\
-	HRCWH_CORE_ENABLE |\
-	HRCWH_FROM_0X00000100 |\
-	HRCWH_BOOTSEQ_DISABLE |\
-	HRCWH_SW_WATCHDOG_DISABLE |\
-	HRCWH_ROM_LOC_LOCAL_16BIT |\
-	HRCWH_RL_EXT_LEGACY |\
-	HRCWH_TSEC1M_IN_MII |\
-	HRCWH_TSEC2M_IN_MII |\
-	HRCWH_BIG_ENDIAN)
-
-/*
- * System IO Config
- */
-#define CONFIG_SYS_SICRH (\
-	SICRH_ESDHC_A_GPIO |\
-	SICRH_ESDHC_B_GPIO |\
-	SICRH_ESDHC_C_GTM |\
-	SICRH_GPIO_A_TSEC2 |\
-	SICRH_GPIO_B_TSEC2_TX_CLK |\
-	SICRH_IEEE1588_A_GPIO |\
-	SICRH_USB |\
-	SICRH_GTM_GPIO |\
-	SICRH_IEEE1588_B_GPIO |\
-	SICRH_ETSEC2_CRS |\
-	SICRH_GPIOSEL_1 |\
-	SICRH_TMROBI_V3P3 |\
-	SICRH_TSOBI1_V3P3 |\
-	SICRH_TSOBI2_V3P3)	/* 0xf577d100 */
-#define CONFIG_SYS_SICRL (\
-	SICRL_SPI_PF0 |\
-	SICRL_UART_PF0 |\
-	SICRL_IRQ_PF0 |\
-	SICRL_I2C2_PF0 |\
-	SICRL_ETSEC1_TX_CLK)	/* 0x00000000 */
-
 #define CONFIG_SYS_GPIO1_PRELIM
 /* GPIO Default input/output settings */
 #define CONFIG_SYS_GPIO1_DIR        0x7AAF8C00
@@ -96,29 +31,15 @@
 #define CONFIG_SYS_GPIO1_DAT        0x08008C00
 
 /*
- * IMMR new address
- */
-#define CONFIG_SYS_IMMR		0xE0000000
-
-/*
  * SERDES
  */
 #define CONFIG_FSL_SERDES
 #define CONFIG_FSL_SERDES1	0xe3000
 
 /*
- * Arbiter Setup
- */
-#define CONFIG_SYS_ACR_PIPE_DEP	3 /* Arbiter pipeline depth is 4 */
-#define CONFIG_SYS_ACR_RPTCNT	3 /* Arbiter repeat count is 4 */
-#define CONFIG_SYS_SPCR_TSECEP	3 /* eTSEC emergency priority is highest */
-
-/*
  * DDR Setup
  */
-#define CONFIG_SYS_DDR_BASE		0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_SDRAM_BASE		0x00000000 /* DDR is system memory */
 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
 #define CONFIG_SYS_DDRCDR_VALUE	(DDRCDR_EN \
 				| DDRCDR_PZ_LOZ \
@@ -205,13 +126,6 @@
 	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 
 /*
- * Local Bus Configuration & Clock Setup
- */
-#define CONFIG_SYS_LCRR_DBYP		LCRR_DBYP
-#define CONFIG_SYS_LCRR_CLKDIV		LCRR_CLKDIV_2
-#define CONFIG_SYS_LBC_LBCR		0x00040000
-
-/*
  * FLASH on the Local Bus
  */
 #define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
@@ -219,22 +133,6 @@
 #define CONFIG_SYS_FLASH_BASE		0xFC000000 /* FLASH base address */
 #define CONFIG_SYS_FLASH_SIZE		64 /* FLASH size is 64M */
 
-/* Window base at flash base */
-#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_64MB)
-
-#define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE \
-				| BR_PS_16	/* 16 bit port */ \
-				| BR_MS_GPCM	/* MSEL = GPCM */ \
-				| BR_V)		/* valid */
-#define CONFIG_SYS_OR0_PRELIM	(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
-				| OR_UPM_XAM \
-				| OR_GPCM_CSNT \
-				| OR_GPCM_ACS_DIV2 \
-				| OR_GPCM_XACS \
-				| OR_GPCM_SCY_4 \
-				| OR_GPCM_TRLX_SET \
-				| OR_GPCM_EHTR_SET)
 
 #define CONFIG_SYS_MAX_FLASH_BANKS	1 /* number of banks */
 #define CONFIG_SYS_MAX_FLASH_SECT	512
@@ -248,33 +146,13 @@
  * SJA1000 CAN controller on Local Bus
  */
 #define CONFIG_SYS_SJA1000_BASE	0xFBFF0000
-#define CONFIG_SYS_BR1_PRELIM	(CONFIG_SYS_SJA1000_BASE \
-				| BR_PS_8	/* 8 bit port size */ \
-				| BR_MS_GPCM	/* MSEL = GPCM */ \
-				| BR_V)		/* valid */
-#define CONFIG_SYS_OR1_PRELIM	(OR_AM_32KB \
-				| OR_GPCM_SCY_5 \
-				| OR_GPCM_EHTR_SET)
-				/* 0xFFFF8052 */
-
-#define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_SJA1000_BASE
-#define CONFIG_SYS_LBLAWAR1_PRELIM	(LBLAWAR_EN | LBLAWAR_32KB)
+
 
 /*
  * CPLD on Local Bus
  */
 #define CONFIG_SYS_CPLD_BASE	0xFBFF8000
-#define CONFIG_SYS_BR2_PRELIM	(CONFIG_SYS_CPLD_BASE \
-				| BR_PS_8	/* 8 bit port */ \
-				| BR_MS_GPCM	/* MSEL = GPCM */ \
-				| BR_V)		/* valid */
-#define CONFIG_SYS_OR2_PRELIM	(OR_AM_32KB \
-				| OR_GPCM_SCY_4 \
-				| OR_GPCM_EHTR_SET)
-				/* 0xFFFF8042 */
-
-#define CONFIG_SYS_LBLAWBAR2_PRELIM	CONFIG_SYS_CPLD_BASE
-#define CONFIG_SYS_LBLAWAR2_PRELIM	(LBLAWAR_EN | LBLAWAR_32KB)
+
 
 /*
  * Serial Port
@@ -386,52 +264,6 @@
 #define CONFIG_SYS_BOOTMAPSZ	(256 << 20) /* Initial Memory map for Linux */
 
 /*
- * Core HID Setup
- */
-#define CONFIG_SYS_HID0_INIT	0x000000000
-#define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK | \
-				 HID0_ENABLE_INSTRUCTION_CACHE | \
-				 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
-#define CONFIG_SYS_HID2		HID2_HBE
-
-/*
- * MMU Setup
- */
-
-/* DDR: cache cacheable */
-#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \
-					BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \
-					BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
-
-/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
-#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_IMMR | BATL_PP_RW | \
-			BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \
-					BATU_VP)
-#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
-
-/* FLASH: icache cacheable, but dcache-inhibit and guarded */
-#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
-					BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \
-					BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT2L	(CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
-					BATL_CACHEINHIBIT | \
-					BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
-
-/* Stack in dcache: cacheable, no memory coherence */
-#define CONFIG_SYS_IBAT3L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
-#define CONFIG_SYS_IBAT3U	(CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
-					BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
-
-/*
  * Environment Configuration
  */
 
diff --git a/include/configs/sbc8349.h b/include/configs/sbc8349.h
index 9074be80f1..d2053cc059 100644
--- a/include/configs/sbc8349.h
+++ b/include/configs/sbc8349.h
@@ -18,36 +18,10 @@
  * High Level Configuration Options
  */
 #define CONFIG_E300		1	/* E300 Family */
-#define CONFIG_MPC834x		1	/* MPC834x family */
-#define CONFIG_MPC8349		1	/* MPC8349 specific */
 
 /* Don't enable PCI2 on sbc834x - it doesn't exist physically. */
 #undef CONFIG_MPC83XX_PCI2		/* support for 2nd PCI controller */
 
-/*
- * The default if PCI isn't enabled, or if no PCI clk setting is given
- * is 66MHz; this is what the board defaults to when the PCI slot is
- * physically empty.  The board will automatically (i.e w/o jumpers)
- * clock down to 33MHz if you insert a 33MHz PCI card.
- */
-#ifdef CONFIG_PCI_33M
-#define CONFIG_83XX_CLKIN	33000000	/* in Hz */
-#else	/* 66M */
-#define CONFIG_83XX_CLKIN	66000000	/* in Hz */
-#endif
-
-#ifndef CONFIG_SYS_CLK_FREQ
-#ifdef CONFIG_PCI_33M
-#define CONFIG_SYS_CLK_FREQ	33000000
-#define HRCWL_CSB_TO_CLKIN	HRCWL_CSB_TO_CLKIN_8X1
-#else	/* 66M */
-#define CONFIG_SYS_CLK_FREQ	66000000
-#define HRCWL_CSB_TO_CLKIN	HRCWL_CSB_TO_CLKIN_4X1
-#endif
-#endif
-
-#define CONFIG_SYS_IMMR		0xE0000000
-
 #undef CONFIG_SYS_DRAM_TEST		/* memory test, takes time */
 #define CONFIG_SYS_MEMTEST_START	0x00000000	/* memtest region */
 #define CONFIG_SYS_MEMTEST_END		0x00100000
@@ -72,9 +46,7 @@
  */
 #undef CONFIG_DDR_32BIT
 
-#define CONFIG_SYS_DDR_BASE		0x00000000 /* DDR is system memory*/
-#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_SDRAM_BASE		0x00000000 /* DDR is system memory*/
 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN | \
 				DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075)
 #define CONFIG_DDR_2T_TIMING
@@ -122,25 +94,6 @@
 #define CONFIG_SYS_FLASH_BASE		0xFF800000	/* start of FLASH   */
 #define CONFIG_SYS_FLASH_SIZE		8		/* flash size in MB */
 
-#define CONFIG_SYS_BR0_PRELIM		(CONFIG_SYS_FLASH_BASE \
-					| BR_PS_16	/* 16 bit port */ \
-					| BR_MS_GPCM	/* MSEL = GPCM */ \
-					| BR_V)		/* valid */
-
-#define CONFIG_SYS_OR0_PRELIM		(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
-					| OR_GPCM_XAM \
-					| OR_GPCM_CSNT \
-					| OR_GPCM_ACS_DIV2 \
-					| OR_GPCM_XACS \
-					| OR_GPCM_SCY_15 \
-					| OR_GPCM_TRLX_SET \
-					| OR_GPCM_EHTR_SET \
-					| OR_GPCM_EAD)
-					/* 0xFF806FF7 */
-
-					/* window base at flash base */
-#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_8MB)
 
 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
 #define CONFIG_SYS_MAX_FLASH_SECT	64	/* sectors per device */
@@ -170,88 +123,8 @@
 #define CONFIG_SYS_MONITOR_LEN	(256 * 1024)	/* Reserve 256 kB for Mon */
 #define CONFIG_SYS_MALLOC_LEN	(256 * 1024)	/* Reserved for malloc */
 
-/*
- * Local Bus LCRR and LBCR regs
- *    LCRR:  DLL bypass, Clock divider is 4
- * External Local Bus rate is
- *    CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
- */
-#define CONFIG_SYS_LCRR_DBYP	LCRR_DBYP
-#define CONFIG_SYS_LCRR_CLKDIV	LCRR_CLKDIV_4
-#define CONFIG_SYS_LBC_LBCR	0x00000000
-
 #undef CONFIG_SYS_LB_SDRAM	/* if board has SDRAM on local bus */
 
-#ifdef CONFIG_SYS_LB_SDRAM
-/* Local bus BR2, OR2 definition for SDRAM if soldered on the board*/
-/*
- * Base Register 2 and Option Register 2 configure SDRAM.
- * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000.
- *
- * For BR2, need:
- *    Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
- *    port-size = 32-bits = BR2[19:20] = 11
- *    no parity checking = BR2[21:22] = 00
- *    SDRAM for MSEL = BR2[24:26] = 011
- *    Valid = BR[31] = 1
- *
- * 0    4    8    12   16   20   24   28
- * 1111 0000 0000 0000 0001 1000 0110 0001 = F0001861
- */
-
-#define CONFIG_SYS_BR2_PRELIM		(CONFIG_SYS_LBC_SDRAM_BASE \
-					| BR_PS_32 \
-					| BR_MS_SDRAM \
-					| BR_V)
-					/* 0xF0001861 */
-#define CONFIG_SYS_LBLAWBAR2_PRELIM	CONFIG_SYS_LBC_SDRAM_BASE
-#define CONFIG_SYS_LBLAWAR2_PRELIM	(LBLAWAR_EN | LBLAWAR_64MB)
-
-/*
- * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
- *
- * For OR2, need:
- *    64MB mask for AM, OR2[0:7] = 1111 1100
- *                 XAM, OR2[17:18] = 11
- *    9 columns OR2[19-21] = 010
- *    13 rows   OR2[23-25] = 100
- *    EAD set for extra time OR[31] = 1
- *
- * 0    4    8    12   16   20   24   28
- * 1111 1100 0000 0000 0110 1001 0000 0001 = FC006901
- */
-
-#define CONFIG_SYS_OR2_PRELIM	(MEG_TO_AM(CONFIG_SYS_LBC_SDRAM_SIZE) \
-			| OR_SDRAM_XAM \
-			| ((9 - OR_SDRAM_MIN_COLS) << OR_SDRAM_COLS_SHIFT) \
-			| ((13 - OR_SDRAM_MIN_ROWS) << OR_SDRAM_ROWS_SHIFT) \
-			| OR_SDRAM_EAD)
-			/* 0xFC006901 */
-
-				/* LB sdram refresh timer, about 6us */
-#define CONFIG_SYS_LBC_LSRT	0x32000000
-				/* LB refresh timer prescal, 266MHz/32 */
-#define CONFIG_SYS_LBC_MRTPR	0x20000000
-
-#define CONFIG_SYS_LBC_LSDMR_COMMON	(LSDMR_RFEN \
-					| LSDMR_BSMA1516 \
-					| LSDMR_RFCR8 \
-					| LSDMR_PRETOACT6 \
-					| LSDMR_ACTTORW3 \
-					| LSDMR_BL8 \
-					| LSDMR_WRC3 \
-					| LSDMR_CL3)
-
-/*
- * SDRAM Controller configuration sequence.
- */
-#define CONFIG_SYS_LBC_LSDMR_1	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_PCHALL)
-#define CONFIG_SYS_LBC_LSDMR_2	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH)
-#define CONFIG_SYS_LBC_LSDMR_3	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH)
-#define CONFIG_SYS_LBC_LSDMR_4	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW)
-#define CONFIG_SYS_LBC_LSDMR_5	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL)
-#endif
-
 /*
  * Serial Port
  */
@@ -309,14 +182,6 @@
 
 #if defined(CONFIG_PCI)
 
-#define PCI_64BIT
-#define PCI_ONE_PCI1
-#if defined(PCI_64BIT)
-#undef PCI_ALL_PCI1
-#undef PCI_TWO_PCI1
-#undef PCI_ONE_PCI1
-#endif
-
 #undef CONFIG_EEPRO100
 #undef CONFIG_TULIP
 
@@ -400,185 +265,14 @@
 
 #define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST  */
 
-#if 1 /*528/264*/
-#define CONFIG_SYS_HRCW_LOW (\
-	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
-	HRCWL_DDR_TO_SCB_CLK_1X1 |\
-	HRCWL_CSB_TO_CLKIN |\
-	HRCWL_VCO_1X2 |\
-	HRCWL_CORE_TO_CSB_2X1)
-#elif 0 /*396/132*/
-#define CONFIG_SYS_HRCW_LOW (\
-	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
-	HRCWL_DDR_TO_SCB_CLK_1X1 |\
-	HRCWL_CSB_TO_CLKIN |\
-	HRCWL_VCO_1X4 |\
-	HRCWL_CORE_TO_CSB_3X1)
-#elif 0 /*264/132*/
-#define CONFIG_SYS_HRCW_LOW (\
-	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
-	HRCWL_DDR_TO_SCB_CLK_1X1 |\
-	HRCWL_CSB_TO_CLKIN |\
-	HRCWL_VCO_1X4 |\
-	HRCWL_CORE_TO_CSB_2X1)
-#elif 0 /*132/132*/
-#define CONFIG_SYS_HRCW_LOW (\
-	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
-	HRCWL_DDR_TO_SCB_CLK_1X1 |\
-	HRCWL_CSB_TO_CLKIN |\
-	HRCWL_VCO_1X4 |\
-	HRCWL_CORE_TO_CSB_1X1)
-#elif 0 /*264/264 */
-#define CONFIG_SYS_HRCW_LOW (\
-	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
-	HRCWL_DDR_TO_SCB_CLK_1X1 |\
-	HRCWL_CSB_TO_CLKIN |\
-	HRCWL_VCO_1X4 |\
-	HRCWL_CORE_TO_CSB_1X1)
-#endif
-
-#if defined(PCI_64BIT)
-#define CONFIG_SYS_HRCW_HIGH (\
-	HRCWH_PCI_HOST |\
-	HRCWH_64_BIT_PCI |\
-	HRCWH_PCI1_ARBITER_ENABLE |\
-	HRCWH_PCI2_ARBITER_DISABLE |\
-	HRCWH_CORE_ENABLE |\
-	HRCWH_FROM_0X00000100 |\
-	HRCWH_BOOTSEQ_DISABLE |\
-	HRCWH_SW_WATCHDOG_DISABLE |\
-	HRCWH_ROM_LOC_LOCAL_16BIT |\
-	HRCWH_TSEC1M_IN_GMII |\
-	HRCWH_TSEC2M_IN_GMII)
-#else
-#define CONFIG_SYS_HRCW_HIGH (\
-	HRCWH_PCI_HOST |\
-	HRCWH_32_BIT_PCI |\
-	HRCWH_PCI1_ARBITER_ENABLE |\
-	HRCWH_PCI2_ARBITER_ENABLE |\
-	HRCWH_CORE_ENABLE |\
-	HRCWH_FROM_0X00000100 |\
-	HRCWH_BOOTSEQ_DISABLE |\
-	HRCWH_SW_WATCHDOG_DISABLE |\
-	HRCWH_ROM_LOC_LOCAL_16BIT |\
-	HRCWH_TSEC1M_IN_GMII |\
-	HRCWH_TSEC2M_IN_GMII)
-#endif
-
 /* System IO Config */
 #define CONFIG_SYS_SICRH 0
 #define CONFIG_SYS_SICRL SICRL_LDP_A
 
-#define CONFIG_SYS_HID0_INIT	0x000000000
-#define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK \
-				| HID0_ENABLE_INSTRUCTION_CACHE)
-
-/* #define CONFIG_SYS_HID0_FINAL	(\
-	HID0_ENABLE_INSTRUCTION_CACHE |\
-	HID0_ENABLE_M_BIT |\
-	HID0_ENABLE_ADDRESS_BROADCAST) */
-
-#define CONFIG_SYS_HID2 HID2_HBE
-
-#define CONFIG_HIGH_BATS	1	/* High BATs supported */
-
-/* DDR @ 0x00000000 */
-#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-
-/* PCI @ 0x80000000 */
 #ifdef CONFIG_PCI
 #define CONFIG_PCI_INDIRECT_BRIDGE
-#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_PCI1_MEM_BASE \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_PCI1_MEM_BASE \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_PCI1_MMIO_BASE \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_PCI1_MMIO_BASE \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#else
-#define CONFIG_SYS_IBAT1L	(0)
-#define CONFIG_SYS_IBAT1U	(0)
-#define CONFIG_SYS_IBAT2L	(0)
-#define CONFIG_SYS_IBAT2U	(0)
 #endif
 
-#ifdef CONFIG_MPC83XX_PCI2
-#define CONFIG_SYS_IBAT3L	(CONFIG_SYS_PCI2_MEM_BASE \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT3U	(CONFIG_SYS_PCI2_MEM_BASE \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_IBAT4L	(CONFIG_SYS_PCI2_MMIO_BASE \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT4U	(CONFIG_SYS_PCI2_MMIO_BASE \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#else
-#define CONFIG_SYS_IBAT3L	(0)
-#define CONFIG_SYS_IBAT3U	(0)
-#define CONFIG_SYS_IBAT4L	(0)
-#define CONFIG_SYS_IBAT4U	(0)
-#endif
-
-/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 */
-#define CONFIG_SYS_IBAT5L	(CONFIG_SYS_IMMR \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT5U	(CONFIG_SYS_IMMR \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-
-/* LBC SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
-#define CONFIG_SYS_IBAT6L	(CONFIG_SYS_LBC_SDRAM_BASE \
-				| BATL_PP_RW \
-				| BATL_MEMCOHERENCE \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT6U	(CONFIG_SYS_LBC_SDRAM_BASE \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-
-#define CONFIG_SYS_IBAT7L	(0)
-#define CONFIG_SYS_IBAT7U	(0)
-
-#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
-#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
-#define CONFIG_SYS_DBAT2L	CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
-#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
-#define CONFIG_SYS_DBAT4L	CONFIG_SYS_IBAT4L
-#define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U
-#define CONFIG_SYS_DBAT5L	CONFIG_SYS_IBAT5L
-#define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
-#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
-#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
-#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
-
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
 #endif
diff --git a/include/configs/sbc8641d.h b/include/configs/sbc8641d.h
index e9e264b40b..d1535b6fac 100644
--- a/include/configs/sbc8641d.h
+++ b/include/configs/sbc8641d.h
@@ -45,7 +45,6 @@
 #define CONFIG_ENV_OVERWRITE
 
 #define CONFIG_BAT_RW		1	/* Use common BAT rw code */
-#define CONFIG_HIGH_BATS	1	/* High BATs supported and enabled */
 
 #undef CONFIG_SPD_EEPROM		/* Do not use SPD EEPROM for DDR setup*/
 #undef CONFIG_DDR_ECC			/* only for ECC DDR module */
diff --git a/include/configs/strider.h b/include/configs/strider.h
index 972543d6bd..8b942e3446 100644
--- a/include/configs/strider.h
+++ b/include/configs/strider.h
@@ -12,100 +12,19 @@
  * High Level Configuration Options
  */
 #define CONFIG_E300		1 /* E300 family */
-#define CONFIG_MPC83xx		1 /* MPC83xx family */
-#define CONFIG_MPC830x		1 /* MPC830x family */
-#define CONFIG_MPC8308		1 /* MPC8308 CPU specific */
-#define CONFIG_STRIDER		1 /* STRIDER board specific */
 
 #define CONFIG_SYS_FSL_ESDHC_ADDR	CONFIG_SYS_MPC83xx_ESDHC_ADDR
 
 /*
- * System Clock Setup
- */
-#define CONFIG_83XX_CLKIN	33333333 /* in Hz */
-#define CONFIG_SYS_CLK_FREQ	CONFIG_83XX_CLKIN
-
-/*
- * Hardware Reset Configuration Word
- * if CLKIN is 66.66MHz, then
- * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz
- * We choose the A type silicon as default, so the core is 400Mhz.
- */
-#define CONFIG_SYS_HRCW_LOW (\
-	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
-	HRCWL_DDR_TO_SCB_CLK_2X1 |\
-	HRCWL_SVCOD_DIV_2 |\
-	HRCWL_CSB_TO_CLKIN_4X1 |\
-	HRCWL_CORE_TO_CSB_3X1)
-/*
- * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits
- * in 8308's HRCWH according to the manual, but original Freescale's
- * code has them and I've expirienced some problems using the board
- * with BDI3000 attached when I've tried to set these bits to zero
- * (UART doesn't work after the 'reset run' command).
- */
-#define CONFIG_SYS_HRCW_HIGH (\
-	HRCWH_PCI_HOST |\
-	HRCWH_PCI1_ARBITER_ENABLE |\
-	HRCWH_CORE_ENABLE |\
-	HRCWH_FROM_0XFFF00100 |\
-	HRCWH_BOOTSEQ_DISABLE |\
-	HRCWH_SW_WATCHDOG_DISABLE |\
-	HRCWH_ROM_LOC_LOCAL_16BIT |\
-	HRCWH_RL_EXT_LEGACY |\
-	HRCWH_TSEC1M_IN_MII |\
-	HRCWH_TSEC2M_IN_RGMII |\
-	HRCWH_BIG_ENDIAN)
-
-/*
- * System IO Config
- */
-#define CONFIG_SYS_SICRH (\
-	SICRH_ESDHC_A_SD |\
-	SICRH_ESDHC_B_SD |\
-	SICRH_ESDHC_C_SD |\
-	SICRH_GPIO_A_GPIO |\
-	SICRH_GPIO_B_GPIO |\
-	SICRH_IEEE1588_A_GPIO |\
-	SICRH_USB |\
-	SICRH_GTM_GPIO |\
-	SICRH_IEEE1588_B_GPIO |\
-	SICRH_ETSEC2_GPIO |\
-	SICRH_GPIOSEL_1 |\
-	SICRH_TMROBI_V3P3 |\
-	SICRH_TSOBI1_V2P5 |\
-	SICRH_TSOBI2_V2P5)	/* 0x0037f103 */
-#define CONFIG_SYS_SICRL (\
-	SICRL_SPI_PF0 |\
-	SICRL_UART_PF0 |\
-	SICRL_IRQ_PF0 |\
-	SICRL_I2C2_PF0 |\
-	SICRL_ETSEC1_TX_CLK)	/* 0x00000000 */
-
-/*
- * IMMR new address
- */
-#define CONFIG_SYS_IMMR		0xE0000000
-
-/*
  * SERDES
  */
 #define CONFIG_FSL_SERDES
 #define CONFIG_FSL_SERDES1	0xe3000
 
 /*
- * Arbiter Setup
- */
-#define CONFIG_SYS_ACR_PIPE_DEP	3 /* Arbiter pipeline depth is 4 */
-#define CONFIG_SYS_ACR_RPTCNT	3 /* Arbiter repeat count is 4 */
-#define CONFIG_SYS_SPCR_TSECEP	3 /* eTSEC emergency priority is highest */
-
-/*
  * DDR Setup
  */
-#define CONFIG_SYS_DDR_BASE		0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_SDRAM_BASE		0x00000000 /* DDR is system memory */
 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
 #define CONFIG_SYS_DDRCDR_VALUE	(DDRCDR_EN \
 				| DDRCDR_PZ_LOZ \
@@ -192,13 +111,6 @@
 	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 
 /*
- * Local Bus Configuration & Clock Setup
- */
-#define CONFIG_SYS_LCRR_DBYP		LCRR_DBYP
-#define CONFIG_SYS_LCRR_CLKDIV		LCRR_CLKDIV_2
-#define CONFIG_SYS_LBC_LBCR		0x00040000
-
-/*
  * FLASH on the Local Bus
  */
 #define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
@@ -208,22 +120,6 @@
 #define CONFIG_SYS_FLASH_BASE		0xFE000000 /* FLASH base address */
 #define CONFIG_SYS_FLASH_SIZE		8 /* FLASH size is up to 8M */
 
-/* Window base at flash base */
-#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_8MB)
-
-#define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE \
-				| BR_PS_16	/* 16 bit port */ \
-				| BR_MS_GPCM	/* MSEL = GPCM */ \
-				| BR_V)		/* valid */
-#define CONFIG_SYS_OR0_PRELIM	(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
-				| OR_UPM_XAM \
-				| OR_GPCM_CSNT \
-				| OR_GPCM_ACS_DIV2 \
-				| OR_GPCM_XACS \
-				| OR_GPCM_SCY_15 \
-				| OR_GPCM_TRLX_SET \
-				| OR_GPCM_EHTR_SET)
 
 #define CONFIG_SYS_MAX_FLASH_BANKS	1 /* number of banks */
 #define CONFIG_SYS_MAX_FLASH_SECT	135
@@ -231,29 +127,6 @@
 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000 /* Flash Erase Timeout (ms) */
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500 /* Flash Write Timeout (ms) */
 
-/*
- * FPGA
- */
-#define CONFIG_SYS_FPGA0_BASE		0xE0600000
-#define CONFIG_SYS_FPGA0_SIZE		1 /* FPGA size is 1M */
-
-/* Window base at FPGA base */
-#define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_FPGA0_BASE
-#define CONFIG_SYS_LBLAWAR1_PRELIM	(LBLAWAR_EN | LBLAWAR_1MB)
-
-#define CONFIG_SYS_BR1_PRELIM	(CONFIG_SYS_FPGA0_BASE \
-				| BR_PS_16	/* 16 bit port */ \
-				| BR_MS_GPCM	/* MSEL = GPCM */ \
-				| BR_V)		/* valid */
-
-#define CONFIG_SYS_OR1_PRELIM   (MEG_TO_AM(CONFIG_SYS_FPGA0_SIZE) \
-				| OR_UPM_XAM \
-				| OR_GPCM_CSNT \
-				| OR_GPCM_SCY_5 \
-				| OR_GPCM_TRLX_CLEAR \
-				| OR_GPCM_EHTR_CLEAR)
-
-#define CONFIG_SYS_FPGA_BASE(k)		CONFIG_SYS_FPGA0_BASE
 #define CONFIG_SYS_FPGA_DONE(k)		0x0010
 
 #define CONFIG_SYS_FPGA_COUNT		1
@@ -547,52 +420,6 @@ void fpga_control_clear(unsigned int bus, int pin);
 #define CONFIG_SYS_BOOTMAPSZ	(256 << 20) /* Initial Memory map for Linux */
 
 /*
- * Core HID Setup
- */
-#define CONFIG_SYS_HID0_INIT	0x000000000
-#define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK | \
-				 HID0_ENABLE_INSTRUCTION_CACHE | \
-				 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
-#define CONFIG_SYS_HID2		HID2_HBE
-
-/*
- * MMU Setup
- */
-
-/* DDR: cache cacheable */
-#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \
-					BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \
-					BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
-
-/* IMMRBAR, PCI IO and FPGA: cache-inhibit and guarded */
-#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_IMMR | BATL_PP_RW | \
-			BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \
-					BATU_VP)
-#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
-
-/* FLASH: icache cacheable, but dcache-inhibit and guarded */
-#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
-					BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \
-					BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT2L	(CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
-					BATL_CACHEINHIBIT | \
-					BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
-
-/* Stack in dcache: cacheable, no memory coherence */
-#define CONFIG_SYS_IBAT3L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
-#define CONFIG_SYS_IBAT3U	(CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
-					BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
-
-/*
  * Environment Configuration
  */
 
diff --git a/include/configs/suvd3.h b/include/configs/suvd3.h
index 3e88c9000c..1705f9cafb 100644
--- a/include/configs/suvd3.h
+++ b/include/configs/suvd3.h
@@ -20,171 +20,16 @@
  * High Level Configuration Options
  */
 
-/* This needs to be set prior to including km/km83xx-common.h */
-
-#if defined(CONFIG_SUVD3)	/* SUVD3 board specific */
 #define CONFIG_HOSTNAME		"suvd3"
-#define CONFIG_KM_BOARD_NAME   "suvd3"
-/* include common defines/options for all 8321 Keymile boards */
-#include "km/km8321-common.h"
-
-#elif defined(CONFIG_KMVECT1)   /* VECT1 board specific */
-#define CONFIG_HOSTNAME		"kmvect1"
-#define CONFIG_KM_BOARD_NAME   "kmvect1"
-/* at end of uboot partition, before env */
-#define CONFIG_SYS_QE_FW_ADDR   0xF00B0000
-/* include common defines/options for all 8309 Keymile boards */
-#include "km/km8309-common.h"
-
-#elif defined(CONFIG_KMTEGR1)   /* TEGR1 board specific */
-#define CONFIG_HOSTNAME   "kmtegr1"
-#define CONFIG_KM_BOARD_NAME   "kmtegr1"
-#define CONFIG_KM_UBI_PARTITION_NAME_BOOT	"ubi0"
-#define CONFIG_KM_UBI_PARTITION_NAME_APP	"ubi1"
-
-#define CONFIG_ENV_ADDR		0xF0100000
-#define CONFIG_ENV_OFFSET	0x100000
-
-#define CONFIG_NAND_ECC_BCH
-#define CONFIG_NAND_KMETER1
-#define CONFIG_SYS_MAX_NAND_DEVICE		1
-#define NAND_MAX_CHIPS				1
-
-/* include common defines/options for all 8309 Keymile boards */
-#include "km/km8309-common.h"
-/* must be after the include because KMBEC_FPGA is otherwise undefined */
-#define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE /* PRIO_BASE_ADDRESS */
-
-#else
-#error Supported boards are: SUVD3, KMVECT1, KMTEGR1
-#endif
-
-#define CONFIG_SYS_APP1_BASE		0xA0000000
-#define CONFIG_SYS_APP1_SIZE		256 /* Megabytes */
-#define CONFIG_SYS_APP2_BASE		0xB0000000
-#define CONFIG_SYS_APP2_SIZE		256 /* Megabytes */
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
-
-/*
- * Init Local Bus Memory Controller:
- *
- * Bank Bus     Machine PortSz  Size  Device
- * ---- ---     ------- ------  -----  ------
- *  2   Local   UPMA    16 bit  256MB APP1
- *  3   Local   GPCM    16 bit  256MB APP2
- *
- */
-
-#if defined(CONFIG_SUVD3) || defined(CONFIG_KMVECT1)
-/*
- * APP1 on the local bus CS2
- */
-#define CONFIG_SYS_LBLAWBAR2_PRELIM	CONFIG_SYS_APP1_BASE
-#define CONFIG_SYS_LBLAWAR2_PRELIM	(LBLAWAR_EN | LBLAWAR_256MB)
-
-#define CONFIG_SYS_BR2_PRELIM	(CONFIG_SYS_APP1_BASE | \
-				 BR_PS_16 | \
-				 BR_MS_UPMA | \
-				 BR_V)
-#define CONFIG_SYS_OR2_PRELIM	(MEG_TO_AM(CONFIG_SYS_APP1_SIZE))
+#define CONFIG_KM_BOARD_NAME	"suvd3"
 
-#define CONFIG_SYS_BR3_PRELIM	(CONFIG_SYS_APP2_BASE | \
-				 BR_PS_16 | \
-				 BR_V)
-
-#define CONFIG_SYS_OR3_PRELIM	(MEG_TO_AM(CONFIG_SYS_APP2_SIZE) | \
-				 OR_GPCM_CSNT | \
-				 OR_GPCM_ACS_DIV4 | \
-				 OR_GPCM_SCY_3 | \
-				 OR_GPCM_TRLX_SET)
+/* include common defines/options for all Keymile boards */
+#include "km/keymile-common.h"
+#include "km/km-powerpc.h"
+#include "km/km-mpc83xx.h"
+#include "km/km-mpc832x.h"
 
 #define CONFIG_SYS_MAMR	(MxMR_GPL_x4DIS | \
 			 0x0000c000 | \
 			 MxMR_WLFx_2X)
-
-#elif defined(CONFIG_KMTEGR1)
-#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_APP2_BASE | \
-				 BR_PS_16 | \
-				 BR_MS_GPCM | \
-				 BR_V)
-
-#define CONFIG_SYS_OR3_PRELIM (MEG_TO_AM(CONFIG_SYS_APP2_SIZE) | \
-				 OR_GPCM_SCY_5 | \
-				 OR_GPCM_TRLX_CLEAR | \
-				 OR_GPCM_EHTR_CLEAR)
-
-#endif /* CONFIG_KMTEGR1 */
-
-#define CONFIG_SYS_LBLAWBAR3_PRELIM	CONFIG_SYS_APP2_BASE
-#define CONFIG_SYS_LBLAWAR3_PRELIM	(LBLAWAR_EN | LBLAWAR_256MB)
-
-/*
- * MMU Setup
- */
-#if defined(CONFIG_SUVD3) || defined(CONFIG_KMVECT1)
-/* APP1:  icache cacheable, but dcache-inhibit and guarded */
-#define CONFIG_SYS_IBAT5L	(CONFIG_SYS_APP1_BASE | BATL_PP_RW | \
-				 BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT5U	(CONFIG_SYS_APP1_BASE | BATU_BL_256M | \
-				 BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT5L	(CONFIG_SYS_APP1_BASE | BATL_PP_RW | \
-				 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
-
-#elif defined(CONFIG_KMTEGR1)
-#define CONFIG_SYS_IBAT5L (0)
-#define CONFIG_SYS_IBAT5U (0)
-#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
-#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
-#endif /* CONFIG_KMTEGR1 */
-
-#define CONFIG_SYS_IBAT6L	(CONFIG_SYS_APP2_BASE | BATL_PP_RW | \
-				 BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT6U	(CONFIG_SYS_APP2_BASE | BATU_BL_256M | \
-				 BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT6L	(CONFIG_SYS_APP2_BASE | BATL_PP_RW | \
-				 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
-
-/*
- * QE UEC ethernet configuration
- */
-#if defined(CONFIG_KMVECT1)
-#define CONFIG_MV88E6352_SWITCH
-#define CONFIG_KM_MVEXTSW_ADDR		0x10
-
-/* ethernet port connected to simple switch 88e6122 (UEC0) */
-#define CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM		0	/* UCC1 */
-#define CONFIG_SYS_UEC1_RX_CLK		QE_CLK9
-#define CONFIG_SYS_UEC1_TX_CLK		QE_CLK10
-
-#define CONFIG_FIXED_PHY		0xFFFFFFFF
-#define CONFIG_SYS_FIXED_PHY_ADDR	0x1E	/* unused address */
-#define CONFIG_SYS_FIXED_PHY_PORT(devnum, speed, duplex) \
-		{devnum, speed, duplex}
-#define CONFIG_SYS_FIXED_PHY_PORTS \
-		CONFIG_SYS_FIXED_PHY_PORT("UEC0", SPEED_100, DUPLEX_FULL)
-
-#define CONFIG_SYS_UEC1_ETH_TYPE	FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR	CONFIG_SYS_FIXED_PHY_ADDR
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE	PHY_INTERFACE_MODE_MII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED	100
-#endif /* CONFIG_KMVECT1 */
-
-#if defined(CONFIG_KMVECT1) || defined(CONFIG_KMTEGR1)
-/* ethernet port connected to piggy (UEC2) */
-#define CONFIG_HAS_ETH1
-#define CONFIG_UEC_ETH2
-#define CONFIG_SYS_UEC2_UCC_NUM		2       /* UCC3 */
-#define CONFIG_SYS_UEC2_RX_CLK		QE_CLK_NONE /* not used in RMII Mode */
-#define CONFIG_SYS_UEC2_TX_CLK		QE_CLK12
-#define CONFIG_SYS_UEC2_ETH_TYPE	FAST_ETH
-#define CONFIG_SYS_UEC2_PHY_ADDR	0
-#define CONFIG_SYS_UEC2_INTERFACE_TYPE	PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC2_INTERFACE_SPEED	100
-#endif /* CONFIG_KMVECT1 || CONFIG_KMTEGR1 */
-
 #endif /* __CONFIG_H */
diff --git a/include/configs/tuge1.h b/include/configs/tuge1.h
new file mode 100644
index 0000000000..808538ef9d
--- /dev/null
+++ b/include/configs/tuge1.h
@@ -0,0 +1,35 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2006 Freescale Semiconductor, Inc.
+ *                    Dave Liu <daveliu@freescale.com>
+ *
+ * Copyright (C) 2007 Logic Product Development, Inc.
+ *                    Peter Barada <peterb@logicpd.com>
+ *
+ * Copyright (C) 2007 MontaVista Software, Inc.
+ *                    Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * (C) Copyright 2008
+ * Heiko Schocher, DENX Software Engineering, hs@denx.de.
+ *
+ * (C) Copyright 2010-2013
+ * Lukas Roggli, KEYMILE Ltd, lukas.roggli@keymile.com
+ * Holger Brunck,  Keymile GmbH, holger.bruncl@keymile.com
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_KM_BOARD_NAME	"tuge1"
+#define CONFIG_HOSTNAME		"tuge1"
+
+/* include common defines/options for all Keymile boards */
+#include "km/keymile-common.h"
+#include "km/km-powerpc.h"
+#include "km/km-mpc83xx.h"
+#include "km/km-mpc832x.h"
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/tuxx1.h b/include/configs/tuxx1.h
index f22d73b8d3..0eb673a947 100644
--- a/include/configs/tuxx1.h
+++ b/include/configs/tuxx1.h
@@ -23,174 +23,17 @@
 /*
  * High Level Configuration Options
  */
-#if defined(CONFIG_KMSUPX5)
-#define CONFIG_KM_BOARD_NAME	"kmsupx5"
-#define CONFIG_HOSTNAME		"kmsupx5"
-#elif defined(CONFIG_TUGE1)
-#define CONFIG_KM_BOARD_NAME	"tuge1"
-#define CONFIG_HOSTNAME		"tuge1"
-#elif defined(CONFIG_TUXX1)	/* TUXX1 board (tuxa1/tuda1) specific */
 #define CONFIG_KM_BOARD_NAME	"tuxx1"
 #define CONFIG_HOSTNAME		"tuxx1"
-#elif defined(CONFIG_KMOPTI2)
-#define CONFIG_KM_BOARD_NAME	"kmopti2"
-#define CONFIG_HOSTNAME		"kmopti2"
-#elif defined(CONFIG_KMTEPR2)
-#define CONFIG_KM_BOARD_NAME    "kmtepr2"
-#define CONFIG_HOSTNAME         "kmtepr2"
-#else
-#error ("Board not supported")
-#endif
 
-/* include common defines/options for all 8321 Keymile boards */
-#include "km/km8321-common.h"
-
-#define CONFIG_SYS_APP1_BASE	0xA0000000    /* PAXG */
-#define	CONFIG_SYS_APP1_SIZE	256 /* Megabytes */
-#if defined(CONFIG_TUXX1) || defined(CONFIG_KMOPTI2) || defined(CONFIG_KMTEPR2)
-#define CONFIG_SYS_APP2_BASE	0xB0000000    /* PINC3 */
-#define	CONFIG_SYS_APP2_SIZE	256 /* Megabytes */
-#endif
-
-/*
- * Init Local Bus Memory Controller:
- *				      Device on board
- * Bank Bus     Machine PortSz Size   TUDA1  TUXA1  TUGE1   KMSUPX4 KMOPTI2
- * -----------------------------------------------------------------------------
- *  2   Local   GPCM    8 bit  256MB  PAXG   LPXF   PAXI    LPXF    PAXE
- *  3   Local   GPCM    8 bit  256MB  PINC3  PINC2  unused  unused  OPI2(16 bit)
- *
- *				      Device on board (continued)
- * Bank Bus     Machine PortSz Size   KMTEPR2
- * -----------------------------------------------------------------------------
- *  2   Local   GPCM    8 bit  256MB  NVRAM
- *  3   Local   GPCM    8 bit  256MB  TEP2 (16 bit)
- */
-
-#if defined(CONFIG_KMTEPRO2)
-/*
- * Configuration for C2 (NVRAM) on the local bus
- */
-#define CONFIG_SYS_LBLAWBAR2_PRELIM    CONFIG_SYS_APP1_BASE
-#define CONFIG_SYS_LBLAWAR2_PRELIM     (LBLAWAR_EN | LBLAWAR_256MB)
-#define CONFIG_SYS_BR2_PRELIM  (CONFIG_SYS_APP1_BASE | \
-				BR_PS_8 | \
-				BR_MS_GPCM | \
-				BR_V)
-#define CONFIG_SYS_OR2_PRELIM  (MEG_TO_AM(CONFIG_SYS_APP1_SIZE) | \
-				OR_GPCM_CSNT | \
-				OR_GPCM_ACS_DIV2 | \
-				OR_GPCM_XACS | \
-				OR_GPCM_SCY_2 | \
-				OR_GPCM_TRLX_SET | \
-				OR_GPCM_EHTR_SET | \
-				OR_GPCM_EAD)
-#else
-/*
- * Configuration for C2 on the local bus
- */
-/* Window base at flash base */
-#define CONFIG_SYS_LBLAWBAR2_PRELIM	CONFIG_SYS_APP1_BASE
-/* Window size: 256 MB */
-#define CONFIG_SYS_LBLAWAR2_PRELIM	(LBLAWAR_EN | LBLAWAR_256MB)
-
-#define CONFIG_SYS_BR2_PRELIM	(CONFIG_SYS_APP1_BASE | \
-				 BR_PS_8 | \
-				 BR_MS_GPCM | \
-				 BR_V)
-
-#define CONFIG_SYS_OR2_PRELIM	(MEG_TO_AM(CONFIG_SYS_APP1_SIZE) | \
-				 OR_GPCM_CSNT | \
-				 OR_GPCM_ACS_DIV4 | \
-				 OR_GPCM_SCY_2 | \
-				 OR_GPCM_TRLX_SET | \
-				 OR_GPCM_EHTR_CLEAR | \
-				 OR_GPCM_EAD)
-#endif
-
-#if defined(CONFIG_TUXX1)
-/*
- * Configuration for C3 on the local bus
- */
-/* Access window base at PINC3 base */
-#define CONFIG_SYS_LBLAWBAR3_PRELIM	CONFIG_SYS_APP2_BASE
-/* Window size: 256 MB */
-#define CONFIG_SYS_LBLAWAR3_PRELIM	(LBLAWAR_EN | LBLAWAR_256MB)
-
-#define CONFIG_SYS_BR3_PRELIM	(CONFIG_SYS_APP2_BASE | \
-				 BR_PS_8 |		\
-				 BR_MS_GPCM |		\
-				 BR_V)
-
-#define CONFIG_SYS_OR3_PRELIM	(MEG_TO_AM(CONFIG_SYS_APP2_SIZE) | \
-				 OR_GPCM_CSNT |	\
-				 OR_GPCM_ACS_DIV2 | \
-				 OR_GPCM_SCY_2 | \
-				 OR_GPCM_TRLX_SET | \
-				 OR_GPCM_EHTR_CLEAR)
+/* include common defines/options for all Keymile boards */
+#include "km/keymile-common.h"
+#include "km/km-powerpc.h"
+#include "km/km-mpc83xx.h"
+#include "km/km-mpc832x.h"
 
 #define CONFIG_SYS_MAMR		(MxMR_GPL_x4DIS | \
 				 0x0000c000 | \
 				 MxMR_WLFx_2X)
-#endif
-
-#if defined(CONFIG_KMOPTI2) || defined(CONFIG_KMTEPR2)
-/*
- * Configuration for C3 on the local bus
- */
-#define CONFIG_SYS_LBLAWBAR3_PRELIM	CONFIG_SYS_APP2_BASE
-#define CONFIG_SYS_LBLAWAR3_PRELIM	(LBLAWAR_EN | LBLAWAR_256MB)
-#define CONFIG_SYS_BR3_PRELIM	(CONFIG_SYS_APP2_BASE | \
-				 BR_PS_16 |		\
-				 BR_MS_GPCM |		\
-				 BR_V)
-#define CONFIG_SYS_OR3_PRELIM	(MEG_TO_AM(CONFIG_SYS_APP2_SIZE) | \
-				 OR_GPCM_SCY_4 | \
-				 OR_GPCM_TRLX_CLEAR | \
-				 OR_GPCM_EHTR_CLEAR)
-#endif
-
-/*
- * MMU Setup
- */
-/* APP1: icache cacheable, but dcache-inhibit and guarded */
-#define CONFIG_SYS_IBAT5L	(CONFIG_SYS_APP1_BASE | \
-				 BATL_PP_RW | \
-				 BATL_MEMCOHERENCE)
-/* 512M should also include APP2... */
-#define CONFIG_SYS_IBAT5U	(CONFIG_SYS_APP1_BASE | \
-				 BATU_BL_256M | \
-				 BATU_VS | \
-				 BATU_VP)
-#define CONFIG_SYS_DBAT5L	(CONFIG_SYS_APP1_BASE | \
-				 BATL_PP_RW | \
-				 BATL_CACHEINHIBIT | \
-				 BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
-
-#if defined(CONFIG_TUGE1) || defined(CONFIG_KMSUPX5)
-#define CONFIG_SYS_IBAT6L	(0)
-#define CONFIG_SYS_IBAT6U	(0)
-#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
-#else
-/* APP2:  icache cacheable, but dcache-inhibit and guarded */
-#define CONFIG_SYS_IBAT6L	(CONFIG_SYS_APP2_BASE | \
-				 BATL_PP_RW | \
-				 BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT6U	(CONFIG_SYS_APP2_BASE | \
-				 BATU_BL_256M | \
-				 BATU_VS | \
-				 BATU_VP)
-#define CONFIG_SYS_DBAT6L	(CONFIG_SYS_APP2_BASE | \
-				 BATL_PP_RW | \
-				 BATL_CACHEINHIBIT | \
-				 BATL_GUARDEDSTORAGE)
-#endif
-#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
-
-#define CONFIG_SYS_IBAT7L	(0)
-#define CONFIG_SYS_IBAT7U	(0)
-#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
 
 #endif /* __CONFIG_H */
diff --git a/include/configs/ve8313.h b/include/configs/ve8313.h
index 85f678e5c4..66f771d818 100644
--- a/include/configs/ve8313.h
+++ b/include/configs/ve8313.h
@@ -16,8 +16,6 @@
  * High Level Configuration Options
  */
 #define CONFIG_E300		1
-#define CONFIG_MPC831x		1
-#define CONFIG_MPC8313		1
 
 #define CONFIG_PCI_INDIRECT_BRIDGE 1
 #define CONFIG_FSL_ELBC		1
@@ -26,18 +24,9 @@
  * On-board devices
  *
  */
-#define CONFIG_83XX_CLKIN	32000000	/* in Hz */
-
-#define CONFIG_SYS_CLK_FREQ	CONFIG_83XX_CLKIN
-
-#define CONFIG_SYS_IMMR		0xE0000000
-
 #define CONFIG_SYS_MEMTEST_START	0x00001000
 #define CONFIG_SYS_MEMTEST_END		0x07000000
 
-#define CONFIG_SYS_ACR_PIPE_DEP		3	/* Arbiter pipeline depth */
-#define CONFIG_SYS_ACR_RPTCNT		3	/* Arbiter repeat count */
-
 /*
  * Device configurations
  */
@@ -45,9 +34,7 @@
 /*
  * DDR Setup
  */
-#define CONFIG_SYS_DDR_BASE		0x00000000 /* DDR is system memory*/
-#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_SDRAM_BASE		0x00000000 /* DDR is system memory*/
 
 /*
  * Manually set up DDR parameters, as this board does not
@@ -117,21 +104,6 @@
 #define CONFIG_SYS_FLASH_SIZE		32	/* size in MB */
 #define CONFIG_SYS_FLASH_EMPTY_INFO		/* display empty sectors */
 
-#define CONFIG_SYS_NOR_BR_PRELIM	(CONFIG_SYS_FLASH_BASE \
-					| BR_PS_16	/* 16 bit */ \
-					| BR_MS_GPCM	/* MSEL = GPCM */ \
-					| BR_V)		/* valid */
-#define CONFIG_SYS_NOR_OR_PRELIM	(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
-					| OR_GPCM_CSNT \
-					| OR_GPCM_ACS_DIV4 \
-					| OR_GPCM_SCY_5 \
-					| OR_GPCM_TRLX_SET \
-					| OR_GPCM_EAD)
-					/* 0xfe000c55 */
-
-#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_32MB)
-
 #define CONFIG_SYS_MAX_FLASH_BANKS	1		/* number of banks */
 #define CONFIG_SYS_MAX_FLASH_SECT	256		/* sectors per dev */
 
@@ -157,16 +129,6 @@
 #define CONFIG_SYS_MALLOC_LEN		(512 * 1024)
 
 /*
- * Local Bus LCRR and LBCR regs
- */
-#define CONFIG_SYS_LCRR_EADC	LCRR_EADC_3
-#define CONFIG_SYS_LCRR_CLKDIV	LCRR_CLKDIV_2
-
-#define CONFIG_SYS_LBC_LBCR	0x00040000
-
-#define CONFIG_SYS_LBC_MRTPR	0x20000000
-
-/*
  * NAND settings
  */
 #define CONFIG_SYS_NAND_BASE		0x61000000
@@ -174,58 +136,13 @@
 #define CONFIG_NAND_FSL_ELBC 1
 #define CONFIG_SYS_NAND_BLOCK_SIZE 16384
 
-#define CONFIG_SYS_NAND_BR_PRELIM	(CONFIG_SYS_NAND_BASE \
-					| BR_PS_8		\
-					| BR_DECC_CHK_GEN	\
-					| BR_MS_FCM		\
-					| BR_V)	/* valid */
-					/* 0x61000c21 */
-#define CONFIG_SYS_NAND_OR_PRELIM	(OR_AM_32KB \
-					| OR_FCM_BCTLD \
-					| OR_FCM_CHT \
-					| OR_FCM_SCY_2 \
-					| OR_FCM_RST \
-					| OR_FCM_TRLX)
-					/* 0xffff90ac */
-
-#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NOR_BR_PRELIM
-#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NOR_OR_PRELIM
-#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM
-#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM
-
-#define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_NAND_BASE
-#define CONFIG_SYS_LBLAWAR1_PRELIM	(LBLAWAR_EN | LBLAWAR_32KB)
-
-#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM
-#define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM
-
-/* CS2 NvRAM */
-#define CONFIG_SYS_BR2_PRELIM	(0x60000000 \
-				| BR_PS_8 \
-				| BR_V)
-				/* 0x60000801 */
-#define CONFIG_SYS_OR2_PRELIM	(OR_AM_128KB \
-				| OR_GPCM_CSNT \
-				| OR_GPCM_XACS \
-				| OR_GPCM_SCY_3 \
-				| OR_GPCM_TRLX_SET \
-				| OR_GPCM_EHTR_SET \
-				| OR_GPCM_EAD)
-				/* 0xfffe0937 */
-/* local bus read write buffer mapping SRAM@0x64000000 */
-#define CONFIG_SYS_BR3_PRELIM	(0x62000000 \
-				| BR_PS_16 \
-				| BR_V)
-				/* 0x62001001 */
-
-#define CONFIG_SYS_OR3_PRELIM	(OR_AM_32MB \
-				| OR_GPCM_CSNT \
-				| OR_GPCM_XACS \
-				| OR_GPCM_SCY_15 \
-				| OR_GPCM_TRLX_SET \
-				| OR_GPCM_EHTR_SET \
-				| OR_GPCM_EAD)
-				/* 0xfe0009f7 */
+
+
+/* Still needed for spl_minimal.c */
+#define CONFIG_SYS_NAND_BR_PRELIM CONFIG_SYS_BR1_PRELIM
+#define CONFIG_SYS_NAND_OR_PRELIM CONFIG_SYS_OR1_PRELIM
+
+
 
 /*
  * Serial Port
@@ -315,25 +232,6 @@
 				/* Initial Memory map for Linux*/
 #define CONFIG_SYS_BOOTMAPSZ	(256 << 20)
 
-/* 0x64050000 */
-#define CONFIG_SYS_HRCW_LOW (\
-	0x20000000 /* reserved, must be set */ |\
-	HRCWL_DDRCM |\
-	HRCWL_CSB_TO_CLKIN_4X1 | \
-	HRCWL_CORE_TO_CSB_2_5X1)
-
-/* 0xa0600004 */
-#define CONFIG_SYS_HRCW_HIGH (HRCWH_PCI_HOST | \
-	HRCWH_PCI_ARBITER_ENABLE | \
-	HRCWH_CORE_ENABLE | \
-	HRCWH_FROM_0X00000100 | \
-	HRCWH_BOOTSEQ_DISABLE |\
-	HRCWH_SW_WATCHDOG_DISABLE |\
-	HRCWH_ROM_LOC_LOCAL_16BIT | \
-	HRCWH_TSEC1M_IN_MII | \
-	HRCWH_BIG_ENDIAN | \
-	HRCWH_LALE_EARLY)
-
 /* System IO Config */
 #define CONFIG_SYS_SICRH	(0x01000000 | \
 				SICRH_ETSEC2_B | \
@@ -353,84 +251,6 @@
 				SICRL_ETSEC2_A)
 				/* 0x33fc0003) */
 
-#define CONFIG_SYS_HID0_INIT	0x000000000
-#define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK | \
-				 HID0_ENABLE_INSTRUCTION_CACHE)
-
-#define CONFIG_SYS_HID2 HID2_HBE
-
-#define CONFIG_HIGH_BATS	1	/* High BATs supported */
-
-/* DDR @ 0x00000000 */
-#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_RW)
-#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-
-#if defined(CONFIG_PCI)
-/* PCI @ 0x80000000 */
-#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_RW)
-#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_PCI1_MEM_BASE \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_PCI1_MMIO_BASE \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_PCI1_MMIO_BASE \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-#else
-#define CONFIG_SYS_IBAT1L	(0)
-#define CONFIG_SYS_IBAT1U	(0)
-#define CONFIG_SYS_IBAT2L	(0)
-#define CONFIG_SYS_IBAT2U	(0)
-#endif
-
-/* PCI2 not supported on 8313 */
-#define CONFIG_SYS_IBAT3L	(0)
-#define CONFIG_SYS_IBAT3U	(0)
-#define CONFIG_SYS_IBAT4L	(0)
-#define CONFIG_SYS_IBAT4U	(0)
-
-/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */
-#define CONFIG_SYS_IBAT5L	(CONFIG_SYS_IMMR \
-				| BATL_PP_RW \
-				| BATL_CACHEINHIBIT \
-				| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT5U	(CONFIG_SYS_IMMR \
-				| BATU_BL_256M \
-				| BATU_VS \
-				| BATU_VP)
-
-/* stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
-#define CONFIG_SYS_IBAT6L	(0xF0000000 | BATL_PP_RW | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT6U	(0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-/*  FPGA, SRAM, NAND @ 0x60000000 */
-#define CONFIG_SYS_IBAT7L	(0x60000000 | BATL_PP_RW | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT7U	(0x60000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
-#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
-#define CONFIG_SYS_DBAT2L	CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
-#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
-#define CONFIG_SYS_DBAT4L	CONFIG_SYS_IBAT4L
-#define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U
-#define CONFIG_SYS_DBAT5L	CONFIG_SYS_IBAT5L
-#define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
-#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
-#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
-#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
-
 #define CONFIG_NETDEV		eth0
 
 #define CONFIG_HOSTNAME		"ve8313"
diff --git a/include/configs/vme8349.h b/include/configs/vme8349.h
index 805f7d3df6..1c3430d849 100644
--- a/include/configs/vme8349.h
+++ b/include/configs/vme8349.h
@@ -18,42 +18,13 @@
 #define __CONFIG_H
 
 /*
- * Top level Makefile configuration choices
- */
-#ifdef CONFIG_CADDY2
-#define VME_CADDY2
-#endif
-
-/*
  * High Level Configuration Options
  */
 #define CONFIG_E300		1	/* E300 Family */
-#define CONFIG_MPC834x		1	/* MPC834x family */
-#define CONFIG_MPC8349		1	/* MPC8349 specific */
-#define CONFIG_VME8349		1	/* ESD VME8349 board specific */
 
 /* Don't enable PCI2 on vme834x - it doesn't exist physically. */
 #undef CONFIG_MPC83XX_PCI2		/* support for 2nd PCI controller */
 
-#define CONFIG_PCI_66M
-#ifdef CONFIG_PCI_66M
-#define CONFIG_83XX_CLKIN	66000000	/* in Hz */
-#else
-#define CONFIG_83XX_CLKIN	33000000	/* in Hz */
-#endif
-
-#ifndef CONFIG_SYS_CLK_FREQ
-#ifdef CONFIG_PCI_66M
-#define CONFIG_SYS_CLK_FREQ	66000000
-#define HRCWL_CSB_TO_CLKIN	HRCWL_CSB_TO_CLKIN_4X1
-#else
-#define CONFIG_SYS_CLK_FREQ	33000000
-#define HRCWL_CSB_TO_CLKIN	HRCWL_CSB_TO_CLKIN_8X1
-#endif
-#endif
-
-#define CONFIG_SYS_IMMR		0xE0000000
-
 #undef CONFIG_SYS_DRAM_TEST			/* memory test, takes time */
 #define CONFIG_SYS_MEMTEST_START	0x00000000	/* memtest region */
 #define CONFIG_SYS_MEMTEST_END		0x00100000
@@ -80,9 +51,7 @@
  */
 #undef CONFIG_DDR_32BIT
 
-#define CONFIG_SYS_DDR_BASE		0x00000000	/* DDR is sys memory*/
-#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_SDRAM_BASE		0x00000000	/* DDR is sys memory*/
 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN \
 					| DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075)
 #define CONFIG_DDR_2T_TIMING
@@ -94,59 +63,12 @@
 /*
  * FLASH on the Local Bus
  */
-#ifdef VME_CADDY2
-#define CONFIG_SYS_FLASH_BASE		0xffc00000	/* start of FLASH   */
-#define CONFIG_SYS_FLASH_SIZE		4		/* flash size in MB */
-#define CONFIG_SYS_BR0_PRELIM		(CONFIG_SYS_FLASH_BASE | \
-					 BR_PS_16 |	/*  16bit */ \
-					 BR_MS_GPCM |	/*  MSEL = GPCM */ \
-					 BR_V)		/* valid */
-
-#define CONFIG_SYS_OR0_PRELIM		(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
-					| OR_GPCM_XAM \
-					| OR_GPCM_CSNT \
-					| OR_GPCM_ACS_DIV2 \
-					| OR_GPCM_XACS \
-					| OR_GPCM_SCY_15 \
-					| OR_GPCM_TRLX_SET \
-					| OR_GPCM_EHTR_SET \
-					| OR_GPCM_EAD)
-					/* 0xffc06ff7 */
-#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_4MB)
-#else
 #define CONFIG_SYS_FLASH_BASE		0xf8000000	/* start of FLASH   */
 #define CONFIG_SYS_FLASH_SIZE		128		/* flash size in MB */
-#define CONFIG_SYS_BR0_PRELIM		(CONFIG_SYS_FLASH_BASE | \
-					 BR_PS_16 |	/*  16bit */ \
-					 BR_MS_GPCM |	/*  MSEL = GPCM */ \
-					 BR_V)		/* valid */
-
-#define CONFIG_SYS_OR0_PRELIM		(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
-					| OR_GPCM_XAM \
-					| OR_GPCM_CSNT \
-					| OR_GPCM_ACS_DIV2 \
-					| OR_GPCM_XACS \
-					| OR_GPCM_SCY_15 \
-					| OR_GPCM_TRLX_SET \
-					| OR_GPCM_EHTR_SET \
-					| OR_GPCM_EAD)
-					/* 0xf8006ff7 */
-#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_128MB)
-#endif
+
 
 #define CONFIG_SYS_WINDOW1_BASE		0xf0000000
-#define CONFIG_SYS_BR1_PRELIM		(CONFIG_SYS_WINDOW1_BASE \
-					| BR_PS_32 \
-					| BR_MS_GPCM \
-					| BR_V)
-					/* 0xF0001801 */
-#define CONFIG_SYS_OR1_PRELIM		(OR_AM_256KB \
-					| OR_GPCM_SETA)
-					/* 0xfffc0208 */
-#define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_WINDOW1_BASE
-#define CONFIG_SYS_LBLAWAR1_PRELIM	(LBLAWAR_EN | LBLAWAR_256KB)
+
 
 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
 #define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device*/
@@ -174,15 +96,6 @@
 #define CONFIG_SYS_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB */
 #define CONFIG_SYS_MALLOC_LEN		(256 * 1024)	/* Malloc size */
 
-/*
- * Local Bus LCRR and LBCR regs
- *    LCRR:  no DLL bypass, Clock divider is 4
- * External Local Bus rate is
- *    CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
- */
-#define CONFIG_SYS_LCRR_CLKDIV	LCRR_CLKDIV_4
-#define CONFIG_SYS_LBC_LBCR	0x00000000
-
 #undef CONFIG_SYS_LB_SDRAM	/* if board has SDRAM on local bus */
 
 /*
@@ -244,14 +157,6 @@
 
 #if defined(CONFIG_PCI)
 
-#define PCI_64BIT
-#define PCI_ONE_PCI1
-#if defined(PCI_64BIT)
-#undef PCI_ALL_PCI1
-#undef PCI_TWO_PCI1
-#undef PCI_ONE_PCI1
-#endif
-
 #undef CONFIG_EEPRO100
 #undef CONFIG_TULIP
 
@@ -341,51 +246,10 @@
 
 #define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST  */
 
-#define CONFIG_SYS_HRCW_LOW (\
-	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
-	HRCWL_DDR_TO_SCB_CLK_1X1 |\
-	HRCWL_CSB_TO_CLKIN |\
-	HRCWL_VCO_1X2 |\
-	HRCWL_CORE_TO_CSB_2X1)
-
-#if defined(PCI_64BIT)
-#define CONFIG_SYS_HRCW_HIGH (\
-	HRCWH_PCI_HOST |\
-	HRCWH_64_BIT_PCI |\
-	HRCWH_PCI1_ARBITER_ENABLE |\
-	HRCWH_PCI2_ARBITER_DISABLE |\
-	HRCWH_CORE_ENABLE |\
-	HRCWH_FROM_0X00000100 |\
-	HRCWH_BOOTSEQ_DISABLE |\
-	HRCWH_SW_WATCHDOG_DISABLE |\
-	HRCWH_ROM_LOC_LOCAL_16BIT |\
-	HRCWH_TSEC1M_IN_GMII |\
-	HRCWH_TSEC2M_IN_GMII)
-#else
-#define CONFIG_SYS_HRCW_HIGH (\
-	HRCWH_PCI_HOST |\
-	HRCWH_32_BIT_PCI |\
-	HRCWH_PCI1_ARBITER_ENABLE |\
-	HRCWH_PCI2_ARBITER_ENABLE |\
-	HRCWH_CORE_ENABLE |\
-	HRCWH_FROM_0X00000100 |\
-	HRCWH_BOOTSEQ_DISABLE |\
-	HRCWH_SW_WATCHDOG_DISABLE |\
-	HRCWH_ROM_LOC_LOCAL_16BIT |\
-	HRCWH_TSEC1M_IN_GMII |\
-	HRCWH_TSEC2M_IN_GMII)
-#endif
-
 /* System IO Config */
 #define CONFIG_SYS_SICRH 0
 #define CONFIG_SYS_SICRL SICRL_LDP_A
 
-#define CONFIG_SYS_HID0_INIT	0x000000000
-#define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK | \
-				 HID0_ENABLE_INSTRUCTION_CACHE)
-
-#define CONFIG_SYS_HID2		HID2_HBE
-
 #define CONFIG_SYS_GPIO1_PRELIM
 #define CONFIG_SYS_GPIO1_DIR	0x00100000
 #define CONFIG_SYS_GPIO1_DAT	0x00100000
@@ -394,84 +258,10 @@
 #define CONFIG_SYS_GPIO2_DIR	0x78900000
 #define CONFIG_SYS_GPIO2_DAT	0x70100000
 
-#define CONFIG_HIGH_BATS		/* High BATs supported */
-
-/* DDR @ 0x00000000 */
-#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \
-				 BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | \
-				 BATU_VS | BATU_VP)
-
-/* PCI @ 0x80000000 */
 #ifdef CONFIG_PCI
 #define CONFIG_PCI_INDIRECT_BRIDGE
-#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_RW | \
-				 BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_PCI1_MEM_BASE | BATU_BL_256M | \
-				 BATU_VS | BATU_VP)
-#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_PCI1_MMIO_BASE | BATL_PP_RW | \
-				 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_PCI1_MMIO_BASE | BATU_BL_256M | \
-				 BATU_VS | BATU_VP)
-#else
-#define CONFIG_SYS_IBAT1L	(0)
-#define CONFIG_SYS_IBAT1U	(0)
-#define CONFIG_SYS_IBAT2L	(0)
-#define CONFIG_SYS_IBAT2U	(0)
 #endif
 
-#ifdef CONFIG_MPC83XX_PCI2
-#define CONFIG_SYS_IBAT3L	(CONFIG_SYS_PCI2_MEM_BASE | BATL_PP_RW | \
-				 BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT3U	(CONFIG_SYS_PCI2_MEM_BASE | BATU_BL_256M | \
-				 BATU_VS | BATU_VP)
-#define CONFIG_SYS_IBAT4L	(CONFIG_SYS_PCI2_MMIO_BASE | BATL_PP_RW | \
-				 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT4U	(CONFIG_SYS_PCI2_MMIO_BASE | BATU_BL_256M | \
-				 BATU_VS | BATU_VP)
-#else
-#define CONFIG_SYS_IBAT3L	(0)
-#define CONFIG_SYS_IBAT3U	(0)
-#define CONFIG_SYS_IBAT4L	(0)
-#define CONFIG_SYS_IBAT4U	(0)
-#endif
-
-/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 */
-#define CONFIG_SYS_IBAT5L	(CONFIG_SYS_IMMR | BATL_PP_RW | \
-				 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT5U	(CONFIG_SYS_IMMR | BATU_BL_256M | \
-				 BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_IBAT6L	(0xF0000000 | BATL_PP_RW | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT6U	(0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#if (CONFIG_SYS_DDR_SIZE == 512)
-#define CONFIG_SYS_IBAT7L	(CONFIG_SYS_SDRAM_BASE+0x10000000 | \
-				 BATL_PP_RW | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT7U	(CONFIG_SYS_SDRAM_BASE+0x10000000 | \
-				 BATU_BL_256M | BATU_VS | BATU_VP)
-#else
-#define CONFIG_SYS_IBAT7L	(0)
-#define CONFIG_SYS_IBAT7U	(0)
-#endif
-
-#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
-#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
-#define CONFIG_SYS_DBAT2L	CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
-#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
-#define CONFIG_SYS_DBAT4L	CONFIG_SYS_IBAT4L
-#define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U
-#define CONFIG_SYS_DBAT5L	CONFIG_SYS_IBAT5L
-#define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
-#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
-#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
-#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
-
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
 #endif
diff --git a/include/configs/xpedite517x.h b/include/configs/xpedite517x.h
index 2d2a87a719..1ef803b020 100644
--- a/include/configs/xpedite517x.h
+++ b/include/configs/xpedite517x.h
@@ -17,7 +17,6 @@
 #define CONFIG_SYS_FORM_3U_VPX	1
 #define CONFIG_LINUX_RESET_VEC	0x100	/* Reset vector used by Linux */
 #define CONFIG_BAT_RW		1	/* Use common BAT rw code */
-#define CONFIG_HIGH_BATS	1	/* High BATs supported and enabled */
 #define CONFIG_ALTIVEC		1
 
 #define CONFIG_PCI_SCAN_SHOW	1	/* show pci devices on startup */
diff --git a/include/gdsys_fpga.h b/include/gdsys_fpga.h
index db4424d3f8..6d38a83d90 100644
--- a/include/gdsys_fpga.h
+++ b/include/gdsys_fpga.h
@@ -7,6 +7,7 @@
 #ifndef __GDSYS_FPGA_H
 #define __GDSYS_FPGA_H
 
+#ifdef CONFIG_GDSYS_LEGACY_DRIVERS
 int init_func_fpga(void);
 
 enum {
@@ -33,6 +34,7 @@ extern struct ihs_fpga *fpga_ptr[];
 		     &fpga_ptr[ix]->fld, \
 		     offsetof(struct ihs_fpga, fld), \
 		     val)
+#endif
 
 struct ihs_gpio {
 	u16 read;
@@ -86,82 +88,7 @@ struct ihs_fpga {
 };
 #endif
 
-#ifdef CONFIG_IO
-struct ihs_fpga {
-	u16 reflection_low;	/* 0x0000 */
-	u16 versions;		/* 0x0002 */
-	u16 fpga_features;	/* 0x0004 */
-	u16 fpga_version;	/* 0x0006 */
-	u16 reserved_0[5];	/* 0x0008 */
-	u16 quad_serdes_reset;	/* 0x0012 */
-	u16 reserved_1[8181];	/* 0x0014 */
-	u16 reflection_high;	/* 0x3ffe */
-};
-#endif
-
-#ifdef CONFIG_IO64
-struct ihs_fpga_channel {
-	u16 status_int;
-	u16 config_int;
-	u16 switch_connect_config;
-	u16 tx_destination;
-};
-
-struct ihs_fpga_hicb {
-	u16 status_int;
-	u16 config_int;
-};
-
-struct ihs_fpga {
-	u16 reflection_low;	/* 0x0000 */
-	u16 versions;		/* 0x0002 */
-	u16 fpga_features;	/* 0x0004 */
-	u16 fpga_version;	/* 0x0006 */
-	u16 reserved_0[5];	/* 0x0008 */
-	u16 quad_serdes_reset;	/* 0x0012 */
-	u16 reserved_1[502];	/* 0x0014 */
-	struct ihs_fpga_channel ch[32];		/* 0x0400 */
-	struct ihs_fpga_channel hicb_ch[32];	/* 0x0500 */
-	u16 reserved_2[7487];	/* 0x0580 */
-	u16 reflection_high;	/* 0x3ffe */
-};
-#endif
-
-#ifdef CONFIG_IOCON
-struct ihs_fpga {
-	u16 reflection_low;	/* 0x0000 */
-	u16 versions;		/* 0x0002 */
-	u16 fpga_version;	/* 0x0004 */
-	u16 fpga_features;	/* 0x0006 */
-	u16 reserved_0[1];	/* 0x0008 */
-	u16 top_interrupt;	/* 0x000a */
-	u16 reserved_1[4];	/* 0x000c */
-	struct ihs_gpio gpio;	/* 0x0014 */
-	u16 mpc3w_control;	/* 0x001a */
-	u16 reserved_2[2];	/* 0x001c */
-	struct ihs_io_ep ep;	/* 0x0020 */
-	u16 reserved_3[9];	/* 0x002e */
-	struct ihs_i2c i2c0;	/* 0x0040 */
-	u16 reserved_4[10];	/* 0x004c */
-	u16 mc_int;		/* 0x0060 */
-	u16 mc_int_en;		/* 0x0062 */
-	u16 mc_status;		/* 0x0064 */
-	u16 mc_control;		/* 0x0066 */
-	u16 mc_tx_data;		/* 0x0068 */
-	u16 mc_tx_address;	/* 0x006a */
-	u16 mc_tx_cmd;		/* 0x006c */
-	u16 mc_res;		/* 0x006e */
-	u16 mc_rx_cmd_status;	/* 0x0070 */
-	u16 mc_rx_data;		/* 0x0072 */
-	u16 reserved_5[69];	/* 0x0074 */
-	u16 reflection_high;	/* 0x00fe */
-	struct ihs_osd osd0;	/* 0x0100 */
-	u16 reserved_6[889];	/* 0x010e */
-	u16 videomem0[2048];	/* 0x0800 */
-};
-#endif
-
-#if defined(CONFIG_HRCON) || defined(CONFIG_STRIDER_CON_DP)
+#if defined(CONFIG_TARGET_HRCON) || defined(CONFIG_STRIDER_CON_DP)
 struct ihs_fpga {
 	u16 reflection_low;	/* 0x0000 */
 	u16 versions;		/* 0x0002 */
@@ -270,25 +197,4 @@ struct ihs_fpga {
 };
 #endif
 
-#ifdef CONFIG_DLVISION_10G
-struct ihs_fpga {
-	u16 reflection_low;	/* 0x0000 */
-	u16 versions;		/* 0x0002 */
-	u16 fpga_version;	/* 0x0004 */
-	u16 fpga_features;	/* 0x0006 */
-	u16 reserved_0[10];	/* 0x0008 */
-	u16 extended_interrupt; /* 0x001c */
-	u16 reserved_1[29];	/* 0x001e */
-	u16 mpc3w_control;	/* 0x0058 */
-	u16 reserved_2[3];	/* 0x005a */
-	struct ihs_i2c i2c0;	/* 0x0060 */
-	u16 reserved_3[2];	/* 0x006c */
-	struct ihs_i2c i2c1;	/* 0x0070 */
-	u16 reserved_4[194];	/* 0x007c */
-	struct ihs_osd osd0;	/* 0x0200 */
-	u16 reserved_5[761];	/* 0x020e */
-	u16 videomem0[2048];	/* 0x0800 */
-};
-#endif
-
 #endif
diff --git a/include/linux/immap_qe.h b/include/linux/immap_qe.h
index 51800096b2..022771fff5 100644
--- a/include/linux/immap_qe.h
+++ b/include/linux/immap_qe.h
@@ -12,11 +12,11 @@
 #define __IMMAP_QE_H__
 
 #ifdef CONFIG_MPC83xx
-#if defined(CONFIG_MPC8360)
+#if defined(CONFIG_ARCH_MPC8360)
 #define QE_MURAM_SIZE		0xc000UL
 #define MAX_QE_RISC		2
 #define QE_NUM_OF_SNUM		28
-#elif defined(CONFIG_MPC832x) || defined(CONFIG_MPC8309)
+#elif defined(CONFIG_ARCH_MPC832X) || defined(CONFIG_ARCH_MPC8309)
 #define QE_MURAM_SIZE		0x4000UL
 #define MAX_QE_RISC		1
 #define QE_NUM_OF_SNUM		28
diff --git a/include/mpc83xx.h b/include/mpc83xx.h
index a4c5bd3837..c2a185321a 100644
--- a/include/mpc83xx.h
+++ b/include/mpc83xx.h
@@ -55,7 +55,7 @@
 #define SPRIDR_PARTID			0xFFFF0000	/* Part Id */
 #define SPRIDR_REVID			0x0000FFFF	/* Revision Id */
 
-#if defined(CONFIG_MPC834x)
+#if defined(CONFIG_ARCH_MPC834X)
 #define REVID_MAJOR(spridr)		((spridr & 0x0000FF00) >> 8)
 #define REVID_MINOR(spridr)		(spridr & 0x000000FF)
 #else
@@ -108,7 +108,7 @@
 #define SPCR_COREPR			0x00300000
 #define SPCR_COREPR_SHIFT		(31-11)
 
-#if defined(CONFIG_MPC834x)
+#if defined(CONFIG_ARCH_MPC834X)
 /* SPCR bits - MPC8349 specific */
 /* TSEC1 data priority */
 #define SPCR_TSEC1DP			0x00003000
@@ -129,9 +129,9 @@
 #define SPCR_TSEC2EP			0x00000003
 #define SPCR_TSEC2EP_SHIFT		(31-31)
 
-#elif defined(CONFIG_MPC8308) || defined(CONFIG_MPC831x) || \
-	defined(CONFIG_MPC837x)
-/* SPCR bits - MPC8308, MPC831x and MPC837x specific */
+#elif defined(CONFIG_ARCH_MPC8308) || defined(CONFIG_ARCH_MPC831X) || \
+	defined(CONFIG_ARCH_MPC837X)
+/* SPCR bits - MPC8308, MPC831x and MPC837X specific */
 /* TSEC data priority */
 #define SPCR_TSECDP			0x00003000
 #define SPCR_TSECDP_SHIFT		(31-19)
@@ -145,7 +145,7 @@
 
 /* SICRL/H - System I/O Configuration Register Low/High
  */
-#if defined(CONFIG_MPC834x)
+#if defined(CONFIG_ARCH_MPC834X)
 /* SICRL bits - MPC8349 specific */
 #define SICRL_LDP_A			0x80000000
 #define SICRL_USB1			0x40000000
@@ -191,7 +191,7 @@
 #define SICRH_TSOBI1			0x00000002
 #define SICRH_TSOBI2			0x00000001
 
-#elif defined(CONFIG_MPC8360)
+#elif defined(CONFIG_ARCH_MPC8360)
 /* SICRL bits - MPC8360 specific */
 #define SICRL_LDP_A			0xC0000000
 #define SICRL_LCLK_1			0x10000000
@@ -208,7 +208,7 @@
 #define SICRH_UC2E1OBI			0x00000002
 #define SICRH_UC2E2OBI			0x00000001
 
-#elif defined(CONFIG_MPC832x)
+#elif defined(CONFIG_ARCH_MPC832X)
 /* SICRL bits - MPC832x specific */
 #define SICRL_LDP_LCS_A			0x80000000
 #define SICRL_IRQ_CKS			0x20000000
@@ -216,7 +216,7 @@
 #define SICRL_URT_CTPR			0x06000000
 #define SICRL_IRQ_CTPR			0x00C00000
 
-#elif defined(CONFIG_MPC8313)
+#elif defined(CONFIG_ARCH_MPC8313)
 /* SICRL bits - MPC8313 specific */
 #define SICRL_LBC			0x30000000
 #define SICRL_UART			0x0C000000
@@ -248,7 +248,7 @@
 #define SICRH_TSOBI1			0x00000002
 #define SICRH_TSOBI2			0x00000001
 
-#elif defined(CONFIG_MPC8315)
+#elif defined(CONFIG_ARCH_MPC8315)
 /* SICRL bits - MPC8315 specific */
 #define SICRL_DMA_CH0			0xc0000000
 #define SICRL_DMA_SPI			0x30000000
@@ -283,8 +283,8 @@
 #define SICRH_TSOBI1			0x00000002
 #define SICRH_TSOBI2			0x00000001
 
-#elif defined(CONFIG_MPC837x)
-/* SICRL bits - MPC837x specific */
+#elif defined(CONFIG_ARCH_MPC837X)
+/* SICRL bits - MPC837X specific */
 #define SICRL_USB_A			0xC0000000
 #define SICRL_USB_B			0x30000000
 #define SICRL_USB_B_SD			0x20000000
@@ -314,7 +314,7 @@
 #define SICRL_LDP_A			0x00000002
 #define SICRL_LDP_B			0x00000001
 
-/* SICRH bits - MPC837x specific */
+/* SICRH bits - MPC837X specific */
 #define SICRH_DDR			0x80000000
 #define SICRH_TSEC1_A			0x10000000
 #define SICRH_TSEC1_B			0x08000000
@@ -336,7 +336,7 @@
 #define SICRH_SPI			0x00000003
 #define SICRH_SPI_SD			0x00000001
 
-#elif defined(CONFIG_MPC8308)
+#elif defined(CONFIG_ARCH_MPC8308)
 /* SICRL bits - MPC8308 specific */
 #define SICRL_SPI_PF0			(0 << 28)
 #define SICRL_SPI_PF1			(1 << 28)
@@ -384,7 +384,7 @@
 #define SICRH_TSOBI2_V3P3		(0 << 0)
 #define SICRH_TSOBI2_V2P5		(1 << 0)
 
-#elif defined(CONFIG_MPC8309)
+#elif defined(CONFIG_ARCH_MPC8309)
 /* SICR_1 */
 #define SICR_1_UART1_UART1S		(0 << (30-2))
 #define SICR_1_UART1_UART1RTS		(1 << (30-2))
@@ -593,7 +593,7 @@
 #define HRCWL_CORE_TO_CSB_2_5X1		0x00050000
 #define HRCWL_CORE_TO_CSB_3X1		0x00060000
 
-#if defined(CONFIG_MPC8360) || defined(CONFIG_MPC832x)
+#if defined(CONFIG_ARCH_MPC8360) || defined(CONFIG_ARCH_MPC832X)
 #define HRCWL_CEVCOD			0x000000C0
 #define HRCWL_CEVCOD_SHIFT		6
 #define HRCWL_CE_PLL_VCO_DIV_4		0x00000000
@@ -639,7 +639,7 @@
 #define HRCWL_CE_TO_PLL_1X30		0x0000001E
 #define HRCWL_CE_TO_PLL_1X31		0x0000001F
 
-#elif defined(CONFIG_MPC8308) || defined(CONFIG_MPC8315)
+#elif defined(CONFIG_ARCH_MPC8308) || defined(CONFIG_ARCH_MPC8315)
 #define HRCWL_SVCOD			0x30000000
 #define HRCWL_SVCOD_SHIFT		28
 #define HRCWL_SVCOD_DIV_2		0x00000000
@@ -647,14 +647,14 @@
 #define HRCWL_SVCOD_DIV_8		0x20000000
 #define HRCWL_SVCOD_DIV_1		0x30000000
 
-#elif defined(CONFIG_MPC837x)
+#elif defined(CONFIG_ARCH_MPC837X)
 #define HRCWL_SVCOD			0x30000000
 #define HRCWL_SVCOD_SHIFT		28
 #define HRCWL_SVCOD_DIV_4		0x00000000
 #define HRCWL_SVCOD_DIV_8		0x10000000
 #define HRCWL_SVCOD_DIV_2		0x20000000
 #define HRCWL_SVCOD_DIV_1		0x30000000
-#elif defined(CONFIG_MPC8309)
+#elif defined(CONFIG_ARCH_MPC8309)
 
 #define HRCWL_CEVCOD			0x000000C0
 #define HRCWL_CEVCOD_SHIFT		6
@@ -720,7 +720,7 @@
 #define HRCWH_PCI_HOST_SHIFT		31
 #define HRCWH_PCI_AGENT			0x00000000
 
-#if defined(CONFIG_MPC834x)
+#if defined(CONFIG_ARCH_MPC834X)
 #define HRCWH_32_BIT_PCI		0x00000000
 #define HRCWH_64_BIT_PCI		0x40000000
 #endif
@@ -731,11 +731,11 @@
 #define HRCWH_PCI_ARBITER_DISABLE	0x00000000
 #define HRCWH_PCI_ARBITER_ENABLE	0x20000000
 
-#if defined(CONFIG_MPC834x)
+#if defined(CONFIG_ARCH_MPC834X)
 #define HRCWH_PCI2_ARBITER_DISABLE	0x00000000
 #define HRCWH_PCI2_ARBITER_ENABLE	0x10000000
 
-#elif defined(CONFIG_MPC8360)
+#elif defined(CONFIG_ARCH_MPC8360)
 #define HRCWH_PCICKDRV_DISABLE		0x00000000
 #define HRCWH_PCICKDRV_ENABLE		0x10000000
 #endif
@@ -755,18 +755,18 @@
 
 #define HRCWH_ROM_LOC_DDR_SDRAM		0x00000000
 #define HRCWH_ROM_LOC_PCI1		0x00100000
-#if defined(CONFIG_MPC834x)
+#if defined(CONFIG_ARCH_MPC834X)
 #define HRCWH_ROM_LOC_PCI2		0x00200000
 #endif
-#if defined(CONFIG_MPC837x)
+#if defined(CONFIG_ARCH_MPC837X)
 #define HRCWH_ROM_LOC_ON_CHIP_ROM	0x00300000
 #endif
 #define HRCWH_ROM_LOC_LOCAL_8BIT	0x00500000
 #define HRCWH_ROM_LOC_LOCAL_16BIT	0x00600000
 #define HRCWH_ROM_LOC_LOCAL_32BIT	0x00700000
 
-#if defined(CONFIG_MPC8308) || defined(CONFIG_MPC831x) || \
-	defined(CONFIG_MPC837x)
+#if defined(CONFIG_ARCH_MPC8308) || defined(CONFIG_ARCH_MPC831X) || \
+	defined(CONFIG_ARCH_MPC837X)
 #define HRCWH_ROM_LOC_NAND_SP_8BIT	0x00100000
 #define HRCWH_ROM_LOC_NAND_SP_16BIT	0x00200000
 #define HRCWH_ROM_LOC_NAND_LP_8BIT	0x00500000
@@ -790,7 +790,7 @@
 #define HRCWH_TSEC2M_IN_SGMII		0x00001800
 #endif
 
-#if defined(CONFIG_MPC834x)
+#if defined(CONFIG_ARCH_MPC834X)
 #define HRCWH_TSEC1M_IN_RGMII		0x00000000
 #define HRCWH_TSEC1M_IN_RTBI		0x00004000
 #define HRCWH_TSEC1M_IN_GMII		0x00008000
@@ -801,7 +801,7 @@
 #define HRCWH_TSEC2M_IN_TBI		0x00003000
 #endif
 
-#if defined(CONFIG_MPC8360)
+#if defined(CONFIG_ARCH_MPC8360)
 #define HRCWH_SECONDARY_DDR_DISABLE	0x00000000
 #define HRCWH_SECONDARY_DDR_ENABLE	0x00000010
 #endif
@@ -818,8 +818,8 @@
 /*
  * RSR - Reset Status Register
  */
-#if defined(CONFIG_MPC8308) || defined(CONFIG_MPC831x) || \
-	defined(CONFIG_MPC837x)
+#if defined(CONFIG_ARCH_MPC8308) || defined(CONFIG_ARCH_MPC831X) || \
+	defined(CONFIG_ARCH_MPC837X)
 #define RSR_RSTSRC			0xF0000000	/* Reset source */
 #define RSR_RSTSRC_SHIFT		28
 #else
@@ -937,8 +937,8 @@
 #define SCCR_PCICM			0x00010000
 #define SCCR_PCICM_SHIFT		16
 
-#if defined(CONFIG_MPC834x)
-/* SCCR bits - MPC834x specific */
+#if defined(CONFIG_ARCH_MPC834X)
+/* SCCR bits - MPC834X specific */
 #define SCCR_TSEC1CM			0xc0000000
 #define SCCR_TSEC1CM_SHIFT		30
 #define SCCR_TSEC1CM_0			0x00000000
@@ -965,7 +965,7 @@
 #define SCCR_USBCM_2			0x00A00000
 #define SCCR_USBCM_3			0x00F00000
 
-#elif defined(CONFIG_MPC8313)
+#elif defined(CONFIG_ARCH_MPC8313)
 /* TSEC1 bits are for TSEC2 as well */
 #define SCCR_TSEC1CM			0xc0000000
 #define SCCR_TSEC1CM_SHIFT		30
@@ -986,7 +986,7 @@
 #define SCCR_USBDRCM_2			0x00200000
 #define SCCR_USBDRCM_3			0x00300000
 
-#elif defined(CONFIG_MPC8308) || defined(CONFIG_MPC8315)
+#elif defined(CONFIG_ARCH_MPC8308) || defined(CONFIG_ARCH_MPC8315)
 /* SCCR bits - MPC8315/MPC8308 specific */
 #define SCCR_TSEC1CM			0xc0000000
 #define SCCR_TSEC1CM_SHIFT		30
@@ -1032,8 +1032,8 @@
 #define SCCR_TDMCM_2			0x00000020
 #define SCCR_TDMCM_3			0x00000030
 
-#elif defined(CONFIG_MPC837x)
-/* SCCR bits - MPC837x specific */
+#elif defined(CONFIG_ARCH_MPC837X)
+/* SCCR bits - MPC837X specific */
 #define SCCR_TSEC1CM			0xc0000000
 #define SCCR_TSEC1CM_SHIFT		30
 #define SCCR_TSEC1CM_0			0x00000000
@@ -1071,7 +1071,7 @@
 #define SCCR_SATACM_1			0x00000055
 #define SCCR_SATACM_2			0x000000aa
 #define SCCR_SATACM_3			0x000000ff
-#elif defined(CONFIG_MPC8309)
+#elif defined(CONFIG_ARCH_MPC8309)
 /* SCCR bits - MPC8309 specific */
 #define SCCR_SDHCCM			0x0c000000
 #define SCCR_SDHCCM_SHIFT		26
@@ -1117,7 +1117,7 @@
  */
 #define CSCONFIG_EN			0x80000000
 #define CSCONFIG_AP			0x00800000
-#if defined(CONFIG_MPC830x) || defined(CONFIG_MPC831x)
+#if defined(CONFIG_ARCH_MPC830X) || defined(CONFIG_ARCH_MPC831X)
 #define CSCONFIG_ODT_RD_NEVER		0x00000000
 #define CSCONFIG_ODT_RD_ONLY_CURRENT	0x00100000
 #define CSCONFIG_ODT_RD_ONLY_OTHER_CS	0x00200000
@@ -1126,10 +1126,10 @@
 #define CSCONFIG_ODT_WR_ONLY_CURRENT	0x00010000
 #define CSCONFIG_ODT_WR_ONLY_OTHER_CS	0x00020000
 #define CSCONFIG_ODT_WR_ALL		0x00040000
-#elif defined(CONFIG_MPC832x)
+#elif defined(CONFIG_ARCH_MPC832X)
 #define CSCONFIG_ODT_RD_CFG		0x00400000
 #define CSCONFIG_ODT_WR_CFG		0x00040000
-#elif defined(CONFIG_MPC8360) || defined(CONFIG_MPC837x)
+#elif defined(CONFIG_ARCH_MPC8360) || defined(CONFIG_ARCH_MPC837X)
 #define CSCONFIG_ODT_RD_NEVER		0x00000000
 #define CSCONFIG_ODT_RD_ONLY_CURRENT	0x00100000
 #define CSCONFIG_ODT_RD_ONLY_OTHER_CS	0x00200000
@@ -1239,14 +1239,14 @@
 #define SDRAM_CFG_SDRAM_TYPE_MASK	0x07000000
 #define SDRAM_CFG_SDRAM_TYPE_SHIFT	24
 #define SDRAM_CFG_DYN_PWR		0x00200000
-#if defined(CONFIG_MPC8308) || defined(CONFIG_MPC831x)
+#if defined(CONFIG_ARCH_MPC8308) || defined(CONFIG_ARCH_MPC831X)
 #define SDRAM_CFG_DBW_MASK		0x00180000
 #define SDRAM_CFG_DBW_16		0x00100000
 #define SDRAM_CFG_DBW_32		0x00080000
 #else
 #define SDRAM_CFG_32_BE			0x00080000
 #endif
-#if !defined(CONFIG_MPC8308)
+#if !defined(CONFIG_ARCH_MPC8308)
 #define SDRAM_CFG_8_BE			0x00040000
 #endif
 #define SDRAM_CFG_NCAP			0x00020000
diff --git a/include/post.h b/include/post.h
index 08a771e405..eb218acde5 100644
--- a/include/post.h
+++ b/include/post.h
@@ -21,7 +21,7 @@
 #define _POST_WORD_ADDR	CONFIG_SYS_POST_WORD_ADDR
 #else
 
-#if defined(CONFIG_MPC8360)
+#if defined(CONFIG_ARCH_MPC8360)
 #include <linux/immap_qe.h>
 #define _POST_WORD_ADDR	(CONFIG_SYS_IMMR + CPM_POST_WORD_ADDR)
 
diff --git a/include/usb/ehci-ci.h b/include/usb/ehci-ci.h
index e4579a5bec..efb2eec5ce 100644
--- a/include/usb/ehci-ci.h
+++ b/include/usb/ehci-ci.h
@@ -147,7 +147,7 @@
 
 #if defined(CONFIG_MPC83xx)
 #define CONFIG_SYS_FSL_USB1_ADDR CONFIG_SYS_MPC83xx_USB1_ADDR
-#if defined(CONFIG_MPC834x)
+#if defined(CONFIG_ARCH_MPC834X)
 #define CONFIG_SYS_FSL_USB2_ADDR CONFIG_SYS_MPC83xx_USB2_ADDR
 #else
 #define CONFIG_SYS_FSL_USB2_ADDR	0