Merge git://www.denx.de/git/u-boot-marvell

Conflicts:
	arch/arm/Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>

5 files changed, 369 insertions, 69 deletions

diff --git a/include/configs/clearfog.h b/include/configs/clearfog.h
new file mode 100644
index 0000000000..f0de827fd2
--- /dev/null
+++ b/include/configs/clearfog.h
@@ -0,0 +1,176 @@
+/*
+ * Copyright (C) 2015 Stefan Roese <sr@denx.de>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef _CONFIG_CLEARFOG_H
+#define _CONFIG_CLEARFOG_H
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+
+#define CONFIG_DISPLAY_BOARDINFO_LATE
+
+/*
+ * TEXT_BASE needs to be below 16MiB, since this area is scrubbed
+ * for DDR ECC byte filling in the SPL before loading the main
+ * U-Boot into it.
+ */
+#define	CONFIG_SYS_TEXT_BASE	0x00800000
+#define CONFIG_SYS_TCLK		250000000	/* 250MHz */
+
+/*
+ * Commands configuration
+ */
+#define CONFIG_SYS_NO_FLASH		/* Declare no flash (NOR/SPI) */
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_EXT4
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_FS_GENERIC
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SF
+#define CONFIG_CMD_SPI
+#define CONFIG_CMD_TFTPPUT
+#define CONFIG_CMD_TIME
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MVTWSI
+#define CONFIG_I2C_MVTWSI_BASE0		MVEBU_TWSI_BASE
+#define CONFIG_SYS_I2C_SLAVE		0x0
+#define CONFIG_SYS_I2C_SPEED		100000
+
+/* SPI NOR flash default params, used by sf commands */
+#define CONFIG_SF_DEFAULT_SPEED		1000000
+#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_3
+#define CONFIG_SPI_FLASH_STMICRO
+
+/*
+ * SDIO/MMC Card Configuration
+ */
+#define CONFIG_MMC
+#define CONFIG_MMC_SDMA
+#define CONFIG_GENERIC_MMC
+#define CONFIG_SDHCI
+#define CONFIG_MV_SDHCI
+#define CONFIG_SYS_MMC_BASE		MVEBU_SDIO_BASE
+
+/* Partition support */
+#define CONFIG_DOS_PARTITION
+#define CONFIG_EFI_PARTITION
+
+/* Additional FS support/configuration */
+#define CONFIG_SUPPORT_VFAT
+
+/* USB/EHCI configuration */
+#define CONFIG_EHCI_IS_TDI
+
+#define CONFIG_ENV_MIN_ENTRIES		128
+
+/* Environment in MMC */
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV		0
+#define CONFIG_ENV_SECT_SIZE		0x200
+#define CONFIG_ENV_SIZE			0x10000
+/*
+ * For SD - reserve 1 LBA for MBR + 1M for u-boot image. The MMC/eMMC
+ * boot image starts @ LBA-0.
+ * As result in MMC/eMMC case it will be a 1 sector gap between u-boot
+ * image and environment
+ */
+#define CONFIG_ENV_OFFSET		0xf0000
+#define CONFIG_ENV_ADDR			CONFIG_ENV_OFFSET
+
+#define CONFIG_PHY_MARVELL		/* there is a marvell phy */
+#define PHY_ANEG_TIMEOUT	8000	/* PHY needs a longer aneg time */
+
+/* PCIe support */
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_PCI
+#define CONFIG_PCI_MVEBU
+#define CONFIG_PCI_PNP
+#define CONFIG_PCI_SCAN_SHOW
+#endif
+
+#define CONFIG_SYS_CONSOLE_INFO_QUIET	/* don't print console @ startup */
+#define CONFIG_SYS_ALT_MEMTEST
+
+/* Keep device tree and initrd in lower memory so the kernel can access them */
+#define CONFIG_EXTRA_ENV_SETTINGS	\
+	"fdt_high=0x10000000\0"		\
+	"initrd_high=0x10000000\0"
+
+/* SPL */
+/*
+ * Select the boot device here
+ *
+ * Currently supported are:
+ * SPL_BOOT_SPI_NOR_FLASH	- Booting via SPI NOR flash
+ * SPL_BOOT_SDIO_MMC_CARD	- Booting via SDIO/MMC card (partition 1)
+ */
+#define SPL_BOOT_SPI_NOR_FLASH		1
+#define SPL_BOOT_SDIO_MMC_CARD		2
+#define CONFIG_SPL_BOOT_DEVICE		SPL_BOOT_SDIO_MMC_CARD
+
+/* Defines for SPL */
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_SIZE			(140 << 10)
+#define CONFIG_SPL_TEXT_BASE		0x40000030
+#define CONFIG_SPL_MAX_SIZE		(CONFIG_SPL_SIZE - 0x0030)
+
+#define CONFIG_SPL_BSS_START_ADDR	(0x40000000 + CONFIG_SPL_SIZE)
+#define CONFIG_SPL_BSS_MAX_SIZE		(16 << 10)
+
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MALLOC_SIMPLE
+#endif
+
+#define CONFIG_SPL_STACK		(0x40000000 + ((192 - 16) << 10))
+#define CONFIG_SPL_BOOTROM_SAVE		(CONFIG_SPL_STACK + 4)
+
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+
+#if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SPI_NOR_FLASH
+/* SPL related SPI defines */
+#define CONFIG_SPL_SPI_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_SUPPORT
+#define CONFIG_SPL_SPI_LOAD
+#define CONFIG_SPL_SPI_BUS		0
+#define CONFIG_SPL_SPI_CS		0
+#define CONFIG_SYS_SPI_U_BOOT_OFFS	0x20000
+#define CONFIG_SYS_U_BOOT_OFFS		CONFIG_SYS_SPI_U_BOOT_OFFS
+#endif
+
+#if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SDIO_MMC_CARD
+/* SPL related MMC defines */
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_LIBDISK_SUPPORT
+#define CONFIG_SYS_MMC_U_BOOT_OFFS		(160 << 10)
+#define CONFIG_SYS_U_BOOT_OFFS			CONFIG_SYS_MMC_U_BOOT_OFFS
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	((CONFIG_SYS_U_BOOT_OFFS / 512)\
+						 + 1)
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS	((512 << 10) / 512) /* 512KiB */
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_FIXED_SDHCI_ALIGNED_BUFFER	0x00180000	/* in SDRAM */
+#endif
+#endif
+
+/*
+ * mv-common.h should be defined after CMD configs since it used them
+ * to enable certain macros
+ */
+#include "mv-common.h"
+
+#endif /* _CONFIG_CLEARFOG_H */
diff --git a/include/configs/db-88f6820-gp.h b/include/configs/db-88f6820-gp.h
index 3673e5e368..ef14132b89 100644
--- a/include/configs/db-88f6820-gp.h
+++ b/include/configs/db-88f6820-gp.h
@@ -10,15 +10,7 @@
 /*
  * High Level Configuration Options (easy to change)
  */
-#define CONFIG_ARMADA_XP		/* SOC Family Name */
-#define CONFIG_ARMADA_38X
-#define CONFIG_DB_88F6820_GP		/* Board target name for DDR training */
 
-#define CONFIG_SYS_L2_PL310
-
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SKIP_LOWLEVEL_INIT	/* disable board lowlevel_init */
-#endif
 #define CONFIG_DISPLAY_BOARDINFO_LATE
 
 /*
@@ -99,16 +91,15 @@
 #define CONFIG_ENV_SECT_SIZE		(256 << 10) /* 256KiB sectors */
 
 #define CONFIG_PHY_MARVELL		/* there is a marvell phy */
-#define CONFIG_PHY_ADDR			{ 1, 0 }
-#define CONFIG_SYS_NETA_INTERFACE_TYPE	PHY_INTERFACE_MODE_RGMII
 #define PHY_ANEG_TIMEOUT	8000	/* PHY needs a longer aneg time */
 
 /* PCIe support */
+#ifndef CONFIG_SPL_BUILD
 #define CONFIG_PCI
 #define CONFIG_PCI_MVEBU
 #define CONFIG_PCI_PNP
 #define CONFIG_PCI_SCAN_SHOW
-#define CONFIG_E1000	/* enable Intel E1000 support for testing */
+#endif
 
 #define CONFIG_SYS_CONSOLE_INFO_QUIET	/* don't print console @ startup */
 #define CONFIG_SYS_ALT_MEMTEST
@@ -139,9 +130,9 @@
 #define CONFIG_SPL_BSS_START_ADDR	(0x40000000 + CONFIG_SPL_SIZE)
 #define CONFIG_SPL_BSS_MAX_SIZE		(16 << 10)
 
-#define CONFIG_SYS_SPL_MALLOC_START	(CONFIG_SPL_BSS_START_ADDR + \
-					 CONFIG_SPL_BSS_MAX_SIZE)
-#define CONFIG_SYS_SPL_MALLOC_SIZE	(16 << 10)
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MALLOC_SIMPLE
+#endif
 
 #define CONFIG_SPL_STACK		(0x40000000 + ((192 - 16) << 10))
 #define CONFIG_SPL_BOOTROM_SAVE		(CONFIG_SPL_STACK + 4)
@@ -158,7 +149,7 @@
 #define CONFIG_SPL_SPI_LOAD
 #define CONFIG_SPL_SPI_BUS		0
 #define CONFIG_SPL_SPI_CS		0
-#define CONFIG_SYS_SPI_U_BOOT_OFFS	0x20000
+#define CONFIG_SYS_SPI_U_BOOT_OFFS	0x24000
 #define CONFIG_SYS_U_BOOT_OFFS		CONFIG_SYS_SPI_U_BOOT_OFFS
 #endif
 
@@ -176,10 +167,6 @@
 #endif
 #endif
 
-/* Enable DDR support in SPL (DDR3 training from Marvell bin_hdr) */
-#define CONFIG_SYS_MVEBU_DDR_A38X
-#define CONFIG_DDR3
-
 /*
  * mv-common.h should be defined after CMD configs since it used them
  * to enable certain macros
diff --git a/include/configs/db-mv784mp-gp.h b/include/configs/db-mv784mp-gp.h
index ab6e5a5bce..c8b0344185 100644
--- a/include/configs/db-mv784mp-gp.h
+++ b/include/configs/db-mv784mp-gp.h
@@ -1,5 +1,5 @@
 /*
- * Copyright (C) 2014 Stefan Roese <sr@denx.de>
+ * Copyright (C) 2014-2015 Stefan Roese <sr@denx.de>
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */
@@ -10,12 +10,8 @@
 /*
  * High Level Configuration Options (easy to change)
  */
-#define CONFIG_ARMADA_XP		/* SOC Family Name */
 #define CONFIG_DB_784MP_GP		/* Board target name for DDR training */
 
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SKIP_LOWLEVEL_INIT	/* disable board lowlevel_init */
-#endif
 #define CONFIG_DISPLAY_BOARDINFO_LATE
 
 /*
@@ -30,13 +26,18 @@
  * Commands configuration
  */
 #define CONFIG_SYS_NO_FLASH		/* Declare no flash (NOR/SPI) */
+#define CONFIG_CMD_CACHE
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_ENV
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_EXT4
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_FS_GENERIC
 #define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
 #define CONFIG_CMD_NAND
 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_PING
+#define CONFIG_CMD_SATA
 #define CONFIG_CMD_SF
 #define CONFIG_CMD_SPI
 #define CONFIG_CMD_TFTPPUT
@@ -64,48 +65,29 @@
 #define CONFIG_ENV_SECT_SIZE		(64 << 10) /* 64KiB sectors */
 
 #define CONFIG_PHY_MARVELL		/* there is a marvell phy */
-#define CONFIG_PHY_ADDR			{ 0x10, 0x11, 0x12, 0x13 }
-#define CONFIG_SYS_NETA_INTERFACE_TYPE	PHY_INTERFACE_MODE_QSGMII
 #define PHY_ANEG_TIMEOUT	8000	/* PHY needs a longer aneg time */
-#define CONFIG_RESET_PHY_R
 
 #define CONFIG_SYS_CONSOLE_INFO_QUIET	/* don't print console @ startup */
 #define CONFIG_SYS_ALT_MEMTEST
 
 /* SATA support */
-#ifdef CONFIG_CMD_IDE
-#define __io
-#define CONFIG_IDE_PREINIT
-#define CONFIG_MVSATA_IDE
-
-/* Needs byte-swapping for ATA data register */
-#define CONFIG_IDE_SWAP_IO
-
-#define CONFIG_SYS_ATA_REG_OFFSET	0x0100 /* Offset for register access */
-#define CONFIG_SYS_ATA_DATA_OFFSET	0x0100 /* Offset for data I/O */
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x0100
-
-/* Each 8-bit ATA register is aligned to a 4-bytes address */
-#define CONFIG_SYS_ATA_STRIDE		4
-
-/* CONFIG_CMD_IDE requires some #defines for ATA registers */
-#define CONFIG_SYS_IDE_MAXBUS		2
-#define CONFIG_SYS_IDE_MAXDEVICE	CONFIG_SYS_IDE_MAXBUS
-
-/* ATA registers base is at SATA controller base */
-#define CONFIG_SYS_ATA_BASE_ADDR	MVEBU_AXP_SATA_BASE
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x2000
-#define CONFIG_SYS_ATA_IDE1_OFFSET	0x4000
-
+#define CONFIG_SYS_SATA_MAX_DEVICE	2
+#define CONFIG_SATA_MV
+#define CONFIG_LIBATA
+#define CONFIG_LBA48
+#define CONFIG_EFI_PARTITION
 #define CONFIG_DOS_PARTITION
-#endif /* CONFIG_CMD_IDE */
+
+/* Additional FS support/configuration */
+#define CONFIG_SUPPORT_VFAT
 
 /* PCIe support */
+#ifndef CONFIG_SPL_BUILD
 #define CONFIG_PCI
 #define CONFIG_PCI_MVEBU
 #define CONFIG_PCI_PNP
 #define CONFIG_PCI_SCAN_SHOW
-#define CONFIG_E1000	/* enable Intel E1000 support for testing */
+#endif
 
 /* NAND */
 #define CONFIG_SYS_NAND_USE_FLASH_BBT
@@ -139,9 +121,9 @@
 #define CONFIG_SPL_BSS_START_ADDR	(0x40000000 + (128 << 10))
 #define CONFIG_SPL_BSS_MAX_SIZE		(16 << 10)
 
-#define CONFIG_SYS_SPL_MALLOC_START	(CONFIG_SPL_BSS_START_ADDR + \
-					 CONFIG_SPL_BSS_MAX_SIZE)
-#define CONFIG_SYS_SPL_MALLOC_SIZE	(16 << 10)
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MALLOC_SIMPLE
+#endif
 
 #define CONFIG_SPL_STACK		(0x40000000 + ((192 - 16) << 10))
 #define CONFIG_SPL_BOOTROM_SAVE		(CONFIG_SPL_STACK + 4)
@@ -161,7 +143,7 @@
 #define CONFIG_SYS_U_BOOT_OFFS		CONFIG_SYS_SPI_U_BOOT_OFFS
 
 /* Enable DDR support in SPL (DDR3 training from Marvell bin_hdr) */
-#define CONFIG_SYS_MVEBU_DDR_AXP
 #define CONFIG_SPD_EEPROM		0x4e
+#define CONFIG_BOARD_ECC_SUPPORT	/* this board supports ECC */
 
 #endif /* _CONFIG_DB_MV7846MP_GP_H */
diff --git a/include/configs/ds414.h b/include/configs/ds414.h
new file mode 100644
index 0000000000..e3c7087a1f
--- /dev/null
+++ b/include/configs/ds414.h
@@ -0,0 +1,162 @@
+/*
+ * Copyright (C) 2014 Stefan Roese <sr@denx.de>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef _CONFIG_SYNOLOGY_DS414_H
+#define _CONFIG_SYNOLOGY_DS414_H
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_DISPLAY_BOARDINFO_LATE
+
+/*
+ * TEXT_BASE needs to be below 16MiB, since this area is scrubbed
+ * for DDR ECC byte filling in the SPL before loading the main
+ * U-Boot into it.
+ */
+#define	CONFIG_SYS_TEXT_BASE	0x00800000
+#define CONFIG_SYS_TCLK		250000000	/* 250MHz */
+
+/*
+ * Commands configuration
+ */
+#define CONFIG_SYS_NO_FLASH		/* Declare no flash (NOR/SPI) */
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SF
+#define CONFIG_CMD_SPI
+#define CONFIG_CMD_TFTPPUT
+#define CONFIG_CMD_TIME
+#define CONFIG_CMD_USB
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MVTWSI
+#define CONFIG_I2C_MVTWSI_BASE0		MVEBU_TWSI_BASE
+#define CONFIG_SYS_I2C_SLAVE		0x0
+#define CONFIG_SYS_I2C_SPEED		100000
+
+/* SPI NOR flash default params, used by sf commands */
+#define CONFIG_SF_DEFAULT_SPEED		1000000
+#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_3
+
+/* Environment in SPI NOR flash */
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_OFFSET		0x7E0000   /* RedBoot config partition in DTS */
+#define CONFIG_ENV_SIZE			(64 << 10) /* 64KiB */
+#define CONFIG_ENV_SECT_SIZE		(64 << 10) /* 64KiB sectors */
+
+#define CONFIG_PHY_MARVELL		/* there is a marvell phy */
+#define CONFIG_PHY_ADDR			{ 0x1, 0x0 }
+#define CONFIG_SYS_NETA_INTERFACE_TYPE	PHY_INTERFACE_MODE_RGMII
+
+#define CONFIG_SYS_ALT_MEMTEST
+
+/* PCIe support */
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_PCI
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PCI_ENUM
+#define CONFIG_PCI_MVEBU
+#define CONFIG_PCI_SCAN_SHOW
+#endif
+
+/* USB/EHCI/XHCI configuration */
+
+#define CONFIG_DM_USB
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
+
+/* FIXME: broken XHCI support
+ * Below defines should enable support for the two rear USB3 ports. Sadly, this
+ * does not work because:
+ * - xhci-pci seems to not support DM_USB, so with that enabled it is not
+ *   found.
+ * - USB init fails, controller does not respond in time */
+#if 0
+#undef CONFIG_DM_USB
+#define CONFIG_USB_XHCI
+#define CONFIG_USB_XHCI_PCI
+#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2
+#endif
+
+#if !defined(CONFIG_USB_XHCI)
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_MARVELL
+#define CONFIG_EHCI_IS_TDI
+#endif
+
+/* why is this only defined in mv-common.h if CONFIG_DM is undefined? */
+#define CONFIG_USB_STORAGE
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
+#define CONFIG_SUPPORT_VFAT
+#define CONFIG_SYS_MVFS
+
+/*
+ * mv-common.h should be defined after CMD configs since it used them
+ * to enable certain macros
+ */
+#include "mv-common.h"
+
+/*
+ * Memory layout while starting into the bin_hdr via the
+ * BootROM:
+ *
+ * 0x4000.4000 - 0x4003.4000	headers space (192KiB)
+ * 0x4000.4030			bin_hdr start address
+ * 0x4003.4000 - 0x4004.7c00	BootROM memory allocations (15KiB)
+ * 0x4007.fffc			BootROM stack top
+ *
+ * The address space between 0x4007.fffc and 0x400f.fff is not locked in
+ * L2 cache thus cannot be used.
+ */
+
+/* SPL */
+/* Defines for SPL */
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_TEXT_BASE		0x40004030
+#define CONFIG_SPL_MAX_SIZE		((128 << 10) - 0x4030)
+
+#define CONFIG_SPL_BSS_START_ADDR	(0x40000000 + (128 << 10))
+#define CONFIG_SPL_BSS_MAX_SIZE		(16 << 10)
+
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MALLOC_SIMPLE
+#endif
+
+#define CONFIG_SPL_STACK		(0x40000000 + ((192 - 16) << 10))
+#define CONFIG_SPL_BOOTROM_SAVE		(CONFIG_SPL_STACK + 4)
+
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+
+/* SPL related SPI defines */
+#define CONFIG_SPL_SPI_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_SUPPORT
+#define CONFIG_SPL_SPI_LOAD
+#define CONFIG_SPL_SPI_BUS		0
+#define CONFIG_SPL_SPI_CS		0
+#define CONFIG_SYS_SPI_U_BOOT_OFFS	0x24000
+
+/* DS414 bus width is 32bits */
+#define CONFIG_DDR_32BIT
+
+/* Use random ethernet address if not configured */
+#define CONFIG_LIB_RAND
+#define CONFIG_NET_RANDOM_ETHADDR
+
+/* Default Environment */
+#define CONFIG_BOOTCOMMAND	"sf read ${loadaddr} 0xd0000 0x700000; bootm"
+#define CONFIG_BOOTARGS		"console=ttyS0,115200"
+#define CONFIG_LOADADDR		0x80000
+#undef CONFIG_PREBOOT		/* override preboot for USB and SPI flash init */
+#define CONFIG_PREBOOT		"usb start; sf probe"
+
+#endif /* _CONFIG_SYNOLOGY_DS414_H */
diff --git a/include/configs/maxbcm.h b/include/configs/maxbcm.h
index da49243ebf..43d7fd03a3 100644
--- a/include/configs/maxbcm.h
+++ b/include/configs/maxbcm.h
@@ -10,10 +10,6 @@
 /*
  * High Level Configuration Options (easy to change)
  */
-#define CONFIG_ARMADA_XP		/* SOC Family Name */
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SKIP_LOWLEVEL_INIT	/* disable board lowlevel_init */
-#endif
 #define CONFIG_DISPLAY_BOARDINFO_LATE
 
 /*
@@ -55,10 +51,7 @@
 #define CONFIG_ENV_SECT_SIZE		(64 << 10) /* 64KiB sectors */
 
 #define CONFIG_PHY_MARVELL		/* there is a marvell phy */
-#define CONFIG_PHY_ADDR			{ 0x0, 0x1, 0x2, 0x3 }
-#define CONFIG_SYS_NETA_INTERFACE_TYPE	PHY_INTERFACE_MODE_SGMII
 #define PHY_ANEG_TIMEOUT	8000	/* PHY needs a longer aneg time */
-#define CONFIG_RESET_PHY_R
 
 #define CONFIG_SYS_CONSOLE_INFO_QUIET	/* don't print console @ startup */
 #define CONFIG_SYS_ALT_MEMTEST
@@ -91,9 +84,9 @@
 #define CONFIG_SPL_BSS_START_ADDR	(0x40000000 + (128 << 10))
 #define CONFIG_SPL_BSS_MAX_SIZE		(16 << 10)
 
-#define CONFIG_SYS_SPL_MALLOC_START	(CONFIG_SPL_BSS_START_ADDR + \
-					 CONFIG_SPL_BSS_MAX_SIZE)
-#define CONFIG_SYS_SPL_MALLOC_SIZE	(16 << 10)
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MALLOC_SIMPLE
+#endif
 
 #define CONFIG_SPL_STACK		(0x40000000 + ((192 - 16) << 10))
 #define CONFIG_SPL_BOOTROM_SAVE		(CONFIG_SPL_STACK + 4)
@@ -112,7 +105,7 @@
 #define CONFIG_SYS_SPI_U_BOOT_OFFS	0x20000
 
 /* Enable DDR support in SPL (DDR3 training from Marvell bin_hdr) */
-#define CONFIG_SYS_MVEBU_DDR_AXP
 #define CONFIG_DDR_FIXED_SIZE		(1 << 20)	/* 1GiB */
+#define CONFIG_BOARD_ECC_SUPPORT	/* this board supports ECC */
 
 #endif /* _CONFIG_DB_MV7846MP_GP_H */