m68k: remove TASREG board

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Acked-by: Stefan Roese <sr@denx.de>

1 files changed, 0 insertions, 287 deletions

diff --git a/include/configs/TASREG.h b/include/configs/TASREG.h
deleted file mode 100644
index 5ad93836227..00000000000
--- a/include/configs/TASREG.h
+++ /dev/null
@@ -1,287 +0,0 @@
-/*
- * Configuation settings for the esd TASREG board.
- *
- * (C) Copyright 2004
- * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef _TASREG_H
-#define _TASREG_H
-
-#ifndef __ASSEMBLY__
-#include <asm/m5249.h>
-#endif
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#define CONFIG_MCF52x2			/* define processor family */
-#define CONFIG_M5249			/* define processor type */
-
-#define CONFIG_MISC_INIT_R      1       /* call misc_init_r()           */
-
-#define CONFIG_MCFTMR
-
-#define CONFIG_MCFUART
-#define CONFIG_SYS_UART_PORT		(0)
-#define CONFIG_BAUDRATE		19200
-
-#undef  CONFIG_WATCHDOG
-
-#undef CONFIG_MONITOR_IS_IN_RAM	              /* no pre-loader required!!! ;-) */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_BSP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-
-#undef CONFIG_CMD_NET
-
-
-#define CONFIG_BOOTDELAY	3
-
-#define CONFIG_SYS_LONGHELP				/* undef to save memory		*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE		1024		/* Console I/O Buffer Size	*/
-#else
-#define CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size	*/
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS		16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_DEVICE_NULLDEV	1	/* include nulldev device	*/
-#define CONFIG_SYS_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
-#define CONFIG_AUTO_COMPLETE	1       /* add autocompletion support   */
-#define CONFIG_LOOPW            1       /* enable loopw command         */
-#define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
-
-#define CONFIG_SYS_LOAD_ADDR	        0x200000	/* default load address */
-
-#define CONFIG_SYS_MEMTEST_START	0x400
-#define CONFIG_SYS_MEMTEST_END		0x380000
-
-/*
- * Clock configuration: enable only one of the following options
- */
-
-#if 0 /* this setting will run the cpu at 11MHz */
-#define CONFIG_SYS_PLL_BYPASS          1                /* bypass PLL for test purpose */
-#undef  CONFIG_SYS_FAST_CLK                             /* MCF5249 can run at 140MHz   */
-#define CONFIG_SYS_CLK		        11289600         /* PLL bypass                  */
-#endif
-
-#if 0 /* this setting will run the cpu at 70MHz */
-#undef  CONFIG_SYS_PLL_BYPASS                           /* bypass PLL for test purpose */
-#undef  CONFIG_SYS_FAST_CLK                             /* MCF5249 can run at 140MHz   */
-#define CONFIG_SYS_CLK		        72185018         /* The next lower speed        */
-#endif
-
-#if 1 /* this setting will run the cpu at 140MHz */
-#undef  CONFIG_SYS_PLL_BYPASS                           /* bypass PLL for test purpose */
-#define CONFIG_SYS_FAST_CLK            1                /* MCF5249 can run at 140MHz   */
-#define	CONFIG_SYS_CLK		        132025600        /* MCF5249 can run at 140MHz   */
-#endif
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-
-#define CONFIG_SYS_MBAR		0x10000000	/* Register Base Addrs */
-#define	CONFIG_SYS_MBAR2	        0x80000000
-
-/*-----------------------------------------------------------------------
- * I2C
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
-#define CONFIG_SYS_I2C_SOFT_SPEED	100000
-#define CONFIG_SYS_I2C_SOFT_SLAVE	0x7F
-
-#if 0 /* push-pull */
-#define	SDA	        0x00800000
-#define	SCL	        0x00000008
-#define DIR0            *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO_EN))
-#define DIR1            *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO1_EN))
-#define OUT0	        *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO_OUT))
-#define OUT1	        *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO1_OUT))
-#define IN0	        *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO_READ))
-#define IN1	        *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO1_READ))
-#define	I2C_INIT	{OUT1|=SDA;OUT0|=SCL;}
-#define	I2C_READ	((IN1&SDA)?1:0)
-#define	I2C_SDA(x)	{if(x)OUT1|=SDA;else OUT1&=~SDA;}
-#define	I2C_SCL(x)	{if(x)OUT0|=SCL;else OUT0&=~SCL;}
-#define	I2C_DELAY	{udelay(5);}
-#define	I2C_ACTIVE	{DIR1|=SDA;}
-#define	I2C_TRISTATE    {DIR1&=~SDA;}
-#else /* open-collector */
-#define	SDA	        0x00800000
-#define	SCL	        0x00000008
-#define DIR0            *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO_EN))
-#define DIR1            *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO1_EN))
-#define OUT0	        *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO_OUT))
-#define OUT1	        *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO1_OUT))
-#define IN0	        *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO_READ))
-#define IN1	        *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO1_READ))
-#define	I2C_INIT	{DIR1&=~SDA;DIR0&=~SCL;OUT1&=~SDA;OUT0&=~SCL;}
-#define	I2C_READ	((IN1&SDA)?1:0)
-#define	I2C_SDA(x)	{if(x)DIR1&=~SDA;else DIR1|=SDA;}
-#define	I2C_SCL(x)	{if(x)DIR0&=~SCL;else DIR0|=SCL;}
-#define	I2C_DELAY	{udelay(5);}
-#define	I2C_ACTIVE	{DIR1|=SDA;}
-#define	I2C_TRISTATE    {DIR1&=~SDA;}
-#endif
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC32	*/
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2	/* Bytes of address	*/
-/* mask of address bits that overflow into the "EEPROM chip address"	*/
-#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW	0x01
-/*
- * The Catalyst CAT24WC32 has 32 byte page write mode using
- * last 5 bits of the address
- */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	0x20000000
-#define CONFIG_SYS_INIT_RAM_SIZE	0x1000	/* Size of used area in internal SRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_ADDR		0xFFC40000	/* Address of Environment Sector*/
-#define CONFIG_ENV_SIZE		0x10000	/* Total Size of Environment Sector	*/
-#define CONFIG_ENV_SECT_SIZE	0x10000 /* see README - env sector total size	*/
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_SDRAM_SIZE		16		/* SDRAM size in MB */
-#define CONFIG_SYS_FLASH_BASE		CONFIG_SYS_CS0_BASE
-
-#if 0 /* test-only */
-#define CONFIG_PRAM             512 /* test-only for SDRAM problem!!!!!!!!!!!!!!!!!!!! */
-#endif
-
-#define CONFIG_SYS_MONITOR_BASE	(CONFIG_SYS_FLASH_BASE + 0x400)
-
-#define CONFIG_SYS_MONITOR_LEN		0x20000
-#define CONFIG_SYS_MALLOC_LEN		(1 * 1024*1024)	/* Reserve 1 MB for malloc()	*/
-#define CONFIG_SYS_BOOTPARAMS_LEN	64*1024
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization ??
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-#define CONFIG_SYS_FLASH_WORD_SIZE	unsigned short	/* flash word size (width)	*/
-#define CONFIG_SYS_FLASH_ADDR0		0x5555	/* 1st address for flash config cycles	*/
-#define CONFIG_SYS_FLASH_ADDR1		0x2AAA	/* 2nd address for flash config cycles	*/
-/*
- * The following defines are added for buggy IOP480 byte interface.
- * All other boards should use the standard values (CPCI405 etc.)
- */
-#define CONFIG_SYS_FLASH_READ0		0x0000	/* 0 is standard			*/
-#define CONFIG_SYS_FLASH_READ1		0x0001	/* 1 is standard			*/
-#define CONFIG_SYS_FLASH_READ2		0x0002	/* 2 is standard			*/
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16
-
-#define ICACHE_STATUS			(CONFIG_SYS_INIT_RAM_ADDR + \
-					 CONFIG_SYS_INIT_RAM_SIZE - 8)
-#define DCACHE_STATUS			(CONFIG_SYS_INIT_RAM_ADDR + \
-					 CONFIG_SYS_INIT_RAM_SIZE - 4)
-#define CONFIG_SYS_ICACHE_INV		(CF_CACR_DCM)
-#define CONFIG_SYS_CACHE_ACR1		(CONFIG_SYS_SDRAM_BASE | \
-					 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
-					 CF_ACR_EN | CF_ACR_SM_ALL)
-#define CONFIG_SYS_CACHE_ICACR		(CF_CACR_CENB | CF_CACR_CEIB | \
-					 CF_CACR_DBWE)
-
-/*-----------------------------------------------------------------------
- * Memory bank definitions
- */
-
-/* CS0 - AMD Flash, address 0xffc00000 */
-#define	CONFIG_SYS_CS0_BASE		0xffc00000
-#define	CONFIG_SYS_CS0_CTRL		0x00001980	/* WS=0110, AA=1, PS=10         */
-/** Note: There is a CSMR0/DRAM vector problem, need to disable C/I ***/
-#define	CONFIG_SYS_CS0_MASK		0x003f0021	/* 4MB, AA=0, WP=0, C/I=1, V=1  */
-
-/* CS1 - FPGA, address 0xe0000000 */
-#define	CONFIG_SYS_CS1_BASE		0xe0000000
-#define	CONFIG_SYS_CS1_CTRL		0x00000d80	/* WS=0011, AA=1, PS=10         */
-#define	CONFIG_SYS_CS1_MASK		0x00010001	/* 128kB, AA=0, WP=0, C/I=0, V=1*/
-
-/*-----------------------------------------------------------------------
- * Port configuration
- */
-#define	CONFIG_SYS_GPIO_FUNC           0x00000008      /* Set gpio pins: none          */
-#define	CONFIG_SYS_GPIO1_FUNC          0x00df00f0      /* 36-39(SWITCH),48-52(FPGAs),54*/
-#define	CONFIG_SYS_GPIO_EN             0x00000008      /* Set gpio output enable       */
-#define	CONFIG_SYS_GPIO1_EN            0x00c70000      /* Set gpio output enable       */
-#define	CONFIG_SYS_GPIO_OUT            0x00000008      /* Set outputs to default state */
-#define	CONFIG_SYS_GPIO1_OUT           0x00c70000      /* Set outputs to default state */
-
-#define CONFIG_SYS_GPIO1_LED           0x00400000      /* user led                     */
-
-/*-----------------------------------------------------------------------
- * FPGA stuff
- */
-#define CONFIG_SYS_FPGA_SPARTAN2	1	    /* using Xilinx Spartan 2 now    */
-#define CONFIG_SYS_FPGA_MAX_SIZE	512*1024    /* 512kByte is enough for XC2S200*/
-
-/* FPGA program pin configuration */
-#define CONFIG_SYS_FPGA_PRG		0x00010000  /* FPGA program pin (ppc output) */
-#define CONFIG_SYS_FPGA_CLK		0x00040000  /* FPGA clk pin (ppc output)     */
-#define CONFIG_SYS_FPGA_DATA		0x00020000  /* FPGA data pin (ppc output)    */
-#define CONFIG_SYS_FPGA_INIT		0x00080000  /* FPGA init pin (ppc input)     */
-#define CONFIG_SYS_FPGA_DONE		0x00100000  /* FPGA done pin (ppc input)     */
-
-#endif	/* _TASREG_H */