arm: Remove snowball and u8500_href boards

These boards have not been converted to generic board by the deadline.
Remove them.

Signed-off-by: Simon Glass <sjg@chromium.org>

2 files changed, 0 insertions, 430 deletions

diff --git a/include/configs/snowball.h b/include/configs/snowball.h
deleted file mode 100644
index de03e76ba19..00000000000
--- a/include/configs/snowball.h
+++ /dev/null
@@ -1,232 +0,0 @@
-/*
- * Copyright (C) ST-Ericsson SA 2009
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * #define DEBUG 1
- */
-
-#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_SNOWBALL
-#define CONFIG_SYS_ICACHE_OFF
-#define CONFIG_SYS_DCACHE_OFF
-#define CONFIG_ARCH_CPU_INIT
-#define CONFIG_BOARD_LATE_INIT
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#define CONFIG_U8500
-
-#define CONFIG_SYS_MEMTEST_START	0x00000000
-#define CONFIG_SYS_MEMTEST_END	0x1FFFFFFF
-
-/*-----------------------------------------------------------------------
- * Size of environment and malloc() pool
- */
-/*
- * If you use U-Boot as crash kernel, make sure that it does not overwrite
- * information saved by kexec during panic. Kexec expects the start
- * address of the executable 32K above "crashkernel" address.
- */
-/*
- * Size of malloc() pool
- */
-#define CONFIG_ENV_SIZE		(8*1024)
-#define CONFIG_SYS_MALLOC_LEN	(CONFIG_ENV_SIZE + 256*1024)
-
-#define CONFIG_ENV_IS_IN_MMC
-#define CONFIG_CMD_ENV
-#define CONFIG_ENV_OFFSET		0x0118000
-#define CONFIG_SYS_MMC_ENV_DEV          0              /* SLOT2: eMMC */
-
-/*
- * PL011 Configuration
- */
-#define CONFIG_PL011_SERIAL
-#define CONFIG_PL011_SERIAL_RLCR
-#define CONFIG_PL011_SERIAL_FLUSH_ON_INIT
-
-/*
- * U8500 UART registers base for 3 serial devices
- */
-#define CFG_UART0_BASE		0x80120000
-#define CFG_UART1_BASE		0x80121000
-#define CFG_UART2_BASE		0x80007000
-#define CFG_SERIAL0		CFG_UART0_BASE
-#define CFG_SERIAL1		CFG_UART1_BASE
-#define CFG_SERIAL2		CFG_UART2_BASE
-#define CONFIG_PL011_CLOCK	38400000
-#define CONFIG_PL01x_PORTS	{ (void *)CFG_SERIAL0, (void *)CFG_SERIAL1, \
-				  (void *)CFG_SERIAL2 }
-#define CONFIG_CONS_INDEX	2
-#define CONFIG_BAUDRATE		115200
-
-/*
- * Devices and file systems
- */
-#define CONFIG_MMC
-#define CONFIG_GENERIC_MMC
-#define CONFIG_DOS_PARTITION
-
-/*
- * Commands
- */
-#define CONFIG_CMD_MMC
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_EXT2
-
-#ifndef CONFIG_BOOTDELAY
-#define CONFIG_BOOTDELAY	1
-#endif
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-
-#undef CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND \
-"mmc dev 1; "								\
-	"if run loadbootscript; "					\
-		"then run bootscript; "					\
-	"else "								\
-		"if run mmcload; "					\
-			"then run mmcboot; "				\
-		"else "							\
-			"mmc dev 0; "					\
-			"if run emmcloadbootscript; "			\
-				"then run bootscript; "			\
-			"else "						\
-				"if run emmcload; "			\
-					"then run emmcboot; "		\
-				"else "					\
-					"echo No media to boot from; "	\
-				"fi; "					\
-			"fi; "						\
-		"fi; "							\
-	"fi; "
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
-	"verify=n\0"							\
-	"loadaddr=0x00100000\0"						\
-	"console=ttyAMA2,115200n8\0"					\
-	"loadbootscript=fatload mmc 1:1 ${loadaddr} boot.scr\0"		\
-	"emmcloadbootscript=fatload mmc 0:2 ${loadaddr} boot.scr\0"	\
-	"bootscript=echo Running bootscript "				\
-		"from mmc ...; source ${loadaddr}\0"			\
-	"memargs256=mem=96M@0 mem_modem=32M@96M mem=32M@128M "		\
-		"hwmem=22M@160M pmem_hwb=42M@182M mem_mali=32@224M\0"	\
-	"memargs512=mem=96M@0 mem_modem=32M@96M hwmem=32M@128M "	\
-		"mem=64M@160M mem_mali=32M@224M "			\
-		"pmem_hwb=128M@256M mem=128M@384M\0"			\
-	"memargs1024=mem=128M@0 mali.mali_mem=32M@128M "		\
-		"hwmem=168M@M160M mem=48M@328M "			\
-		"mem_issw=1M@383M mem=640M@384M\0"			\
-	"memargs=setenv bootargs ${bootargs} ${memargs1024}\0"		\
-	"emmcload=fatload mmc 0:2 ${loadaddr} uImage\0"			\
-	"mmcload=fatload mmc 1:1 ${loadaddr} uImage\0"			\
-	"commonargs=setenv bootargs console=${console} "		\
-	"vmalloc=300M\0"						\
-	"emmcargs=setenv bootargs ${bootargs} "				\
-		"root=/dev/mmcblk0p3 "					\
-		"rootwait\0"						\
-	"addcons=setenv bootargs ${bootargs} "				\
-		"console=${console}\0"					\
-	"emmcboot=echo Booting from eMMC ...; "				\
-		"run commonargs emmcargs memargs; "			\
-		"bootm ${loadaddr}\0"					\
-	"mmcargs=setenv bootargs ${bootargs} "				\
-		"root=/dev/mmcblk1p2 "					\
-		"rootwait earlyprintk\0"				\
-	"mmcboot=echo Booting from external MMC ...; "			\
-		"run commonargs mmcargs memargs; "			\
-		"bootm ${loadaddr}\0"					\
-	"fdt_high=0x2BC00000\0"						\
-	"stdout=serial,usbtty\0"					\
-	"stdin=serial,usbtty\0"						\
-	"stderr=serial,usbtty\0"
-
-/*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- */
-
-#define CONFIG_SYS_LONGHELP			/* undef to save memory     */
-#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size  */
-
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE \
-					+ sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS	32	/* max number of command args */
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE /* Boot Arg Buffer Size */
-
-#define CONFIG_SYS_LOAD_ADDR		0x00100000 /* default load address */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	1
-
-#define CONFIG_SYS_HUSH_PARSER		1
-#define CONFIG_CMDLINE_EDITING
-
-#define CONFIG_SETUP_MEMORY_TAGS	2
-#define CONFIG_INITRD_TAG		1
-#define CONFIG_CMDLINE_TAG		1	/* enable passing of ATAGs  */
-
-/*
- * Physical Memory Map
- */
-#define CONFIG_NR_DRAM_BANKS		1
-#define PHYS_SDRAM_1			0x00000000	/* DDR-SDRAM Bank #1 */
-
-/*
- * additions for new relocation code
- */
-#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
-#define CONFIG_SYS_MAX_RAM_SIZE	0x40000000
-#define CONFIG_SYS_INIT_RAM_SIZE	0x100000
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_SDRAM_BASE + \
-					 CONFIG_SYS_INIT_RAM_SIZE - \
-					 GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR		CONFIG_SYS_GBL_DATA_OFFSET
-
-/* landing address before relocation */
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE            0x0
-#endif
-
-/*
- * MMC related configs
- */
-#define CONFIG_ARM_PL180_MMCI
-#define MMC_BLOCK_SIZE			512
-#define CFG_EMMC_BASE                   0x80114000
-#define CFG_MMC_BASE                    0x80126000
-
-/*
- * FLASH and environment organization
- */
-#define CONFIG_SYS_NO_FLASH
-
-/*
- * base register values for U8500
- */
-#define CFG_PRCMU_BASE		0x80157000	/* Power, reset and clock */
-
-
-/*
- * U8500 GPIO register base for 9 banks
- */
-#define CONFIG_DB8500_GPIO
-#define CFG_GPIO_0_BASE			0x8012E000
-#define CFG_GPIO_1_BASE			0x8012E080
-#define CFG_GPIO_2_BASE			0x8000E000
-#define CFG_GPIO_3_BASE			0x8000E080
-#define CFG_GPIO_4_BASE			0x8000E100
-#define CFG_GPIO_5_BASE			0x8000E180
-#define CFG_GPIO_6_BASE			0x8011E000
-#define CFG_GPIO_7_BASE			0x8011E080
-#define CFG_GPIO_8_BASE			0xA03FE000
-
-#define CFG_FSMC_BASE		0x80000000	/* FSMC Controller */
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/u8500_href.h b/include/configs/u8500_href.h
deleted file mode 100644
index a8cc0306cb1..00000000000
--- a/include/configs/u8500_href.h
+++ /dev/null
@@ -1,198 +0,0 @@
-/*
- * Copyright (C) ST-Ericsson SA 2009
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#define CONFIG_U8500
-
-#define CONFIG_SYS_MEMTEST_START	0x00000000
-#define CONFIG_SYS_MEMTEST_END	0x1FFFFFFF
-
-#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_BOARD_LATE_INIT
-
-/*
- * Size of malloc() pool
- */
-#ifdef CONFIG_BOOT_SRAM
-#define CONFIG_ENV_SIZE		(32*1024)
-#define CONFIG_SYS_MALLOC_LEN	(CONFIG_ENV_SIZE + 64*1024)
-#else
-#define CONFIG_ENV_SIZE		(128*1024)
-#define CONFIG_SYS_MALLOC_LEN	(CONFIG_ENV_SIZE + 256*1024)
-#endif
-
-/*
- * PL011 Configuration
- */
-#define CONFIG_PL011_SERIAL
-#define CONFIG_PL011_SERIAL_RLCR
-#define CONFIG_PL011_SERIAL_FLUSH_ON_INIT
-
-/*
- * U8500 UART registers base for 3 serial devices
- */
-#define CFG_UART0_BASE		0x80120000
-#define CFG_UART1_BASE		0x80121000
-#define CFG_UART2_BASE		0x80007000
-#define CFG_SERIAL0		CFG_UART0_BASE
-#define CFG_SERIAL1		CFG_UART1_BASE
-#define CFG_SERIAL2		CFG_UART2_BASE
-#define CONFIG_PL011_CLOCK	38400000
-#define CONFIG_PL01x_PORTS	{ (void *)CFG_SERIAL0, (void *)CFG_SERIAL1, \
-				  (void *)CFG_SERIAL2 }
-#define CONFIG_CONS_INDEX	2
-#define CONFIG_BAUDRATE		115200
-
-/*
- * Devices and file systems
- */
-#define CONFIG_MMC
-#define CONFIG_GENERIC_MMC
-#define CONFIG_DOS_PARTITION
-
-/*
- * Commands
- */
-#define CONFIG_CMD_MMC
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_I2C
-
-#ifndef CONFIG_BOOTDELAY
-#define CONFIG_BOOTDELAY	1
-#endif
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-
-#undef CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND	"run emmcboot"
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
-	"verify=n\0"							\
-	"loadaddr=0x00100000\0"						\
-	"console=ttyAMA2,115200n8\0"					\
-	"memargs256=mem=96M@0 mem_modem=32M@96M mem=30M@128M "		\
-		"pmem=22M@158M pmem_hwb=44M@180M mem_mali=32@224M\0"	\
-	"memargs512=mem=96M@0 mem_modem=32M@96M mem=44M@128M "		\
-		"pmem=22M@172M mem=30M@194M mem_mali=32M@224M "		\
-		"pmem_hwb=54M@256M mem=202M@310M\0"			\
-	"commonargs=setenv bootargs cachepolicy=writealloc noinitrd "	\
-		"init=init "						\
-		"board_id=${board_id} "					\
-		"logo.${logo} "						\
-		"startup_graphics=${startup_graphics}\0"		\
-	"emmcargs=setenv bootargs ${bootargs} "				\
-		"root=/dev/mmcblk0p2 "					\
-		"rootdelay=1\0"						\
-	"addcons=setenv bootargs ${bootargs} "				\
-		"console=${console}\0"					\
-	"emmcboot=echo Booting from eMMC ...; "				\
-		"run commonargs emmcargs addcons memargs;"		\
-		"mmc read 0 ${loadaddr} 0xA0000 0x4000;"		\
-		"bootm ${loadaddr}\0"					\
-	"flash=mmc init 1;fatload mmc 1 ${loadaddr} flash.scr;"		\
-		"source ${loadaddr}\0"					\
-	"loaduimage=mmc init 1;fatload mmc 1 ${loadaddr} uImage\0"	\
-	"usbtty=cdc_acm\0"						\
-	"stdout=serial,usbtty\0"					\
-	"stdin=serial,usbtty\0"						\
-	"stderr=serial,usbtty\0"
-
-/*
- * Miscellaneous configurable options
- */
-
-#define CONFIG_SYS_LONGHELP			/* undef to save memory     */
-#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size  */
-
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE \
-					+ sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS	32	/* max number of command args */
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE /* Boot Arg Buffer Size */
-
-#define CONFIG_SYS_LOAD_ADDR		0x00100000 /* default load address */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE
-
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_CMDLINE_EDITING
-
-#define CONFIG_SETUP_MEMORY_TAGS	2
-#define CONFIG_INITRD_TAG
-#define CONFIG_CMDLINE_TAG			/* enable passing of ATAGs  */
-
-/*
- * I2C
- */
-#define CONFIG_U8500_I2C
-#undef	CONFIG_HARD_I2C			/* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		0	/* slave addr of controller */
-#define CONFIG_SYS_U8500_I2C0_BASE		0x80004000
-#define CONFIG_SYS_U8500_I2C1_BASE		0x80122000
-#define CONFIG_SYS_U8500_I2C2_BASE		0x80128000
-#define CONFIG_SYS_U8500_I2C3_BASE		0x80110000
-#define CONFIG_SYS_U8500_I2C_BUS_MAX		4
-
-#define CONFIG_SYS_I2C_GPIOE_ADDR	0x42	/* GPIO expander chip addr */
-#define CONFIG_TC35892_GPIO
-
-/*
- * Physical Memory Map
- */
-#define CONFIG_NR_DRAM_BANKS		1
-#define PHYS_SDRAM_1			0x00000000	/* DDR-SDRAM Bank #1 */
-#define PHYS_SDRAM_SIZE_1		0x20000000	/* 512 MB */
-
-/*
- * additions for new relocation code
- */
-#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_RAM_SIZE	0x100000
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_SDRAM_BASE + \
-					 CONFIG_SYS_INIT_RAM_SIZE - \
-					 GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR		CONFIG_SYS_GBL_DATA_OFFSET
-
-/* landing address before relocation */
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE            0x0
-#endif
-
-/*
- * MMC related configs
- * NB Only externa SD slot is currently supported
- */
-#define MMC_BLOCK_SIZE			512
-#define CONFIG_ARM_PL180_MMCI
-#define CONFIG_ARM_PL180_MMCI_BASE	0x80126000	/* MMC base for 8500  */
-#define CONFIG_ARM_PL180_MMCI_CLOCK_FREQ 6250000
-#define CONFIG_MMC_DEV_NUM		1
-
-#define CONFIG_CMD_ENV
-#define CONFIG_ENV_IS_IN_MMC
-#define CONFIG_ENV_OFFSET		0x13F80000
-#define CONFIG_SYS_MMC_ENV_DEV          0               /* SLOT2: eMMC */
-
-/*
- * FLASH and environment organization
- */
-#define CONFIG_SYS_NO_FLASH
-
-/*
- * base register values for U8500
- */
-#define CFG_PRCMU_BASE		0x80157000	/* Power, reset and clock
-						   management unit */
-#define CFG_FSMC_BASE		0x80000000	/* FSMC Controller */
-
-#endif	/* __CONFIG_H */