summaryrefslogtreecommitdiff
path: root/include/configs/zylonite.h
diff options
context:
space:
mode:
authorMarkus Klotzbuecher <mk@denx.de>2006-04-25 16:48:48 +0200
committerMarkus Klotzbuecher <mk@pollux.denx.de>2006-04-25 16:48:48 +0200
commit7c93b2443cce08dc9093d47bbaf11c45f7cde9c3 (patch)
tree65da0fa97eb0e8717233735c95eb95374dcda3fb /include/configs/zylonite.h
parent71ae411a63a32aad5151bc2e1d9c0aeff97edaa8 (diff)
NAND support for zylonite board + some minor cleanup.
Diffstat (limited to 'include/configs/zylonite.h')
-rw-r--r--include/configs/zylonite.h140
1 files changed, 56 insertions, 84 deletions
diff --git a/include/configs/zylonite.h b/include/configs/zylonite.h
index 4232d504ee9..c6aa8ece5b0 100644
--- a/include/configs/zylonite.h
+++ b/include/configs/zylonite.h
@@ -76,14 +76,17 @@
#define CONFIG_BAUDRATE 115200
-/* #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_MMC | CFG_CMD_FAT) */
#ifdef TURN_ON_ETHERNET
# define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PING)
#else
-# define CONFIG_COMMANDS (CONFIG_CMD_DFL & ~CFG_CMD_NET)
+# define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
+ | CFG_CMD_ENV \
+ | CFG_CMD_NAND) \
+ & ~(CFG_CMD_NET \
+ | CFG_CMD_FLASH \
+ | CFG_CMD_IMLS))
#endif
-
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
@@ -127,8 +130,11 @@
#define CFG_LOAD_ADDR (CFG_DRAM_BASE + 0x8000) /* default load address */
-#define CFG_HZ 3686400 /* incrementer freq: 3.6864 MHz */
-#define CFG_CPUSPEED 0x161 /* set core clock to 400/200/100 MHz */
+#define CFG_HZ 3250000 /* incrementer freq: 3.25 MHz */
+
+/* Monahans Core Frequency */
+#define CFG_MONAHANS_RUN_MODE_OSC_RATIO 16 /* valid values: 8, 16, 24, 31 */
+#define CFG_MONAHANS_TURBO_RUN_MODE_RATIO 1 /* valid values: 1, 2 */
/* valid baudrates */
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
@@ -159,98 +165,64 @@
#define PHYS_SDRAM_4 0xac000000 /* SDRAM Bank #4 */
#define PHYS_SDRAM_4_SIZE 0x00000000 /* 0 MB */
-#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */
-#define PHYS_FLASH_2 0x04000000 /* Flash Bank #2 */
-#define PHYS_FLASH_SIZE 0x02000000 /* 32 MB */
-#define PHYS_FLASH_BANK_SIZE 0x02000000 /* 32 MB Banks */
-#define PHYS_FLASH_SECT_SIZE 0x00040000 /* 256 KB sectors (x2) */
+#define CFG_DRAM_BASE 0x80000000 /* at CS0 */
+#define CFG_DRAM_SIZE 0x04000000 /* 64 MB Ram */
-#define CFG_DRAM_BASE 0xa0000000
-#define CFG_DRAM_SIZE 0x04000000
+#undef CFG_SKIP_DRAM_SCRUB
-#define CFG_FLASH_BASE PHYS_FLASH_1
-
-#define FPGA_REGS_BASE_PHYSICAL 0x08000000
/*
- * GPIO settings
+ * NAND Flash
*/
-#define CFG_GPSR0_VAL 0x00008000
-#define CFG_GPSR1_VAL 0x00FC0382
-#define CFG_GPSR2_VAL 0x0001FFFF
-#define CFG_GPCR0_VAL 0x00000000
-#define CFG_GPCR1_VAL 0x00000000
-#define CFG_GPCR2_VAL 0x00000000
-#define CFG_GPDR0_VAL 0x0060A800
-#define CFG_GPDR1_VAL 0x00FF0382
-#define CFG_GPDR2_VAL 0x0001C000
-#define CFG_GAFR0_L_VAL 0x98400000
-#define CFG_GAFR0_U_VAL 0x00002950
-#define CFG_GAFR1_L_VAL 0x000A9558
-#define CFG_GAFR1_U_VAL 0x0005AAAA
-#define CFG_GAFR2_L_VAL 0xA0000000
-#define CFG_GAFR2_U_VAL 0x00000002
-
-#define CFG_PSSR_VAL 0x20
+/* Use the new NAND code. (BOARDLIBS = drivers/nand/libnand.a required) */
+#define CONFIG_NEW_NAND_CODE
+#define CFG_NAND0_BASE 0x0
+#undef CFG_NAND1_BASE
-/*
- * Memory settings
- */
-#define CFG_MSC0_VAL 0x23F223F2
-#define CFG_MSC1_VAL 0x3FF1A441
-#define CFG_MSC2_VAL 0x7FF97FF1
-#define CFG_MDCNFG_VAL 0x00001AC9
-#define CFG_MDREFR_VAL 0x00018018
-#define CFG_MDMRS_VAL 0x00000000
+#define CFG_NAND_BASE_LIST { CFG_NAND0_BASE }
+#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
-/*
- * PCMCIA and CF Interfaces
- */
-#define CFG_MECR_VAL 0x00000000
-#define CFG_MCMEM0_VAL 0x00010504
-#define CFG_MCMEM1_VAL 0x00010504
-#define CFG_MCATT0_VAL 0x00010504
-#define CFG_MCATT1_VAL 0x00010504
-#define CFG_MCIO0_VAL 0x00004715
-#define CFG_MCIO1_VAL 0x00004715
+/* nand timeout values */
+#define CFG_NAND_PROG_ERASE_TO 3000
+#define CFG_NAND_OTHER_TO 100
+#define CFG_NAND_SENDCMD_RETRY 3
+#undef NAND_ALLOW_ERASE_ALL /* Allow erasing bad blocks - don't use */
-#define _LED 0x08000010
-#define LED_BLANK 0x08000040
+/* NAND Timing Parameters (in ns) */
+#define NAND_TIMING_tCH 10
+#define NAND_TIMING_tCS 0
+#define NAND_TIMING_tWH 20
+#define NAND_TIMING_tWP 40
-/*
- * FLASH and environment organization
- */
-#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
+#define NAND_TIMING_tRH 20
+#define NAND_TIMING_tRP 40
-/* timeout values are in ticks */
-#define CFG_FLASH_ERASE_TOUT (25*CFG_HZ) /* Timeout for Flash Erase */
-#define CFG_FLASH_WRITE_TOUT (25*CFG_HZ) /* Timeout for Flash Write */
+#define NAND_TIMING_tR 11123
+#define NAND_TIMING_tWHR 100
+#define NAND_TIMING_tAR 10
-/* NOTE: many default partitioning schemes assume the kernel starts at the
- * second sector, not an environment. You have been warned!
- */
-#define CFG_MONITOR_LEN PHYS_FLASH_SECT_SIZE
+/* NAND debugging */
+#define CFG_DFC_DEBUG1 /* usefull */
+#undef CFG_DFC_DEBUG2 /* noisy */
+#undef CFG_DFC_DEBUG3 /* extremly noisy */
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_ADDR (PHYS_FLASH_1 + PHYS_FLASH_SECT_SIZE)
-#define CFG_ENV_SECT_SIZE PHYS_FLASH_SECT_SIZE
-#define CFG_ENV_SIZE (PHYS_FLASH_SECT_SIZE / 16)
+#define CONFIG_MTD_DEBUG
+#define CONFIG_MTD_DEBUG_VERBOSE 1
+#define ADDR_COLUMN 1
+#define ADDR_PAGE 2
+#define ADDR_COLUMN_PAGE 3
+
+#define NAND_ChipID_UNKNOWN 0x00
+#define NAND_MAX_FLOORS 1
+#define NAND_MAX_CHIPS 1
+
+#define CFG_NO_FLASH 1
+
+#define CFG_ENV_IS_IN_NAND 1
+#define CFG_ENV_OFFSET 0x40000
+#define CFG_ENV_OFFSET_REDUND 0x44000
+#define CFG_ENV_SIZE 0x4000
-/*
- * FPGA Offsets
- */
-#define WHOAMI_OFFSET 0x00
-#define HEXLED_OFFSET 0x10
-#define BLANKLED_OFFSET 0x40
-#define DISCRETELED_OFFSET 0x40
-#define CNFG_SWITCHES_OFFSET 0x50
-#define USER_SWITCHES_OFFSET 0x60
-#define MISC_WR_OFFSET 0x80
-#define MISC_RD_OFFSET 0x90
-#define INT_MASK_OFFSET 0xC0
-#define INT_CLEAR_OFFSET 0xD0
-#define GP_OFFSET 0x100
#endif /* __CONFIG_H */