rename CFG_ macros to CONFIG_SYS

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

1 files changed, 92 insertions, 92 deletions

diff --git a/include/configs/uc101.h b/include/configs/uc101.h
index e8daae33b90..553eb25fbbd 100644
--- a/include/configs/uc101.h
+++ b/include/configs/uc101.h
@@ -33,7 +33,7 @@
 #define CONFIG_MPC5200		1	/* (more precisely an MPC5200 CPU)	*/
 #define CONFIG_UC101		1	/* UC101 board			*/
 
-#define CFG_MPC5XXX_CLKIN	33000000 /* ... running at 33.000000MHz		*/
+#define CONFIG_SYS_MPC5XXX_CLKIN	33000000 /* ... running at 33.000000MHz		*/
 
 #define BOOTFLAG_COLD		0x01	/* Normal Power-On: Boot from FLASH	*/
 #define BOOTFLAG_WARM		0x02	/* Software reboot			*/
@@ -47,7 +47,7 @@
  */
 #define CONFIG_PSC_CONSOLE	1	/* console is on PSC1	*/
 #define CONFIG_BAUDRATE		115200	/* ... at 115200 bps	*/
-#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
+#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
 
 /* Partitions */
 #define CONFIG_DOS_PARTITION
@@ -84,7 +84,7 @@
 #define	CONFIG_TIMESTAMP	1	/* Print image info with timestamp */
 
 #if (TEXT_BASE == 0xFFF00000) /* Boot low */
-#   define CFG_LOWBOOT		1
+#   define CONFIG_SYS_LOWBOOT		1
 #endif
 
 /*
@@ -120,56 +120,56 @@
 /*
  * IPB Bus clocking configuration.
  */
-#define CFG_IPBCLK_EQUALS_XLBCLK		/* define for 133MHz speed */
+#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK		/* define for 133MHz speed */
 
 /*
  * I2C configuration
  */
 #define CONFIG_HARD_I2C		1	/* I2C with hardware support */
-#define CFG_I2C_MODULE		2	/* Select I2C module #1 or #2 */
+#define CONFIG_SYS_I2C_MODULE		2	/* Select I2C module #1 or #2 */
 
-#define CFG_I2C_SPEED		100000 /* 100 kHz */
-#define CFG_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C_SPEED		100000 /* 100 kHz */
+#define CONFIG_SYS_I2C_SLAVE		0x7F
 
 /*
  * EEPROM configuration
  */
-#define CFG_I2C_EEPROM_ADDR		0x58
-#define CFG_I2C_EEPROM_ADDR_LEN		1
-#define CFG_EEPROM_PAGE_WRITE_BITS	4
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10
+#define CONFIG_SYS_I2C_EEPROM_ADDR		0x58
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	4
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10
 
 /*
  * RTC configuration
  */
 #define CONFIG_RTC_PCF8563
-#define CFG_I2C_RTC_ADDR		0x51
+#define CONFIG_SYS_I2C_RTC_ADDR		0x51
 
 /* I2C SYSMON (LM75) */
 #define CONFIG_DTT_LM81			1	/* ON Semi's LM75		*/
 #define CONFIG_DTT_SENSORS		{0}	/* Sensor addresses		*/
-#define CFG_DTT_MAX_TEMP		70
-#define CFG_DTT_LOW_TEMP		-30
-#define CFG_DTT_HYSTERESIS		3
+#define CONFIG_SYS_DTT_MAX_TEMP		70
+#define CONFIG_SYS_DTT_LOW_TEMP		-30
+#define CONFIG_SYS_DTT_HYSTERESIS		3
 
 /*
  * Flash configuration
  */
-#define CFG_FLASH_BASE		0xFF800000
+#define CONFIG_SYS_FLASH_BASE		0xFF800000
 
-#define CFG_FLASH_SIZE		0x00800000 /* 8 MByte */
-#define CFG_MAX_FLASH_SECT	140	/* max num of sects on one chip */
+#define CONFIG_SYS_FLASH_SIZE		0x00800000 /* 8 MByte */
+#define CONFIG_SYS_MAX_FLASH_SECT	140	/* max num of sects on one chip */
 
 #define CONFIG_ENV_ADDR		(TEXT_BASE+0x40000) /* second sector */
-#define CFG_MAX_FLASH_BANKS	1	/* max num of flash banks
+#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max num of flash banks
 					   (= chip selects) */
-#define CFG_FLASH_ERASE_TOUT	240000	/* Flash Erase Timeout (in ms)	*/
-#define CFG_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (in ms)	*/
+#define CONFIG_SYS_FLASH_ERASE_TOUT	240000	/* Flash Erase Timeout (in ms)	*/
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (in ms)	*/
 
 #define CONFIG_FLASH_CFI_DRIVER
-#define CFG_FLASH_CFI
-#define CFG_FLASH_EMPTY_INFO
-#define CFG_FLASH_CFI_AMD_RESET
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_CFI_AMD_RESET
 
 /*
  * Environment settings
@@ -183,14 +183,14 @@
 /*
  * Memory map
  */
-#define CFG_MBAR		0xF0000000
-#define CFG_DEFAULT_MBAR	0x80000000
+#define CONFIG_SYS_MBAR		0xF0000000
+#define CONFIG_SYS_DEFAULT_MBAR	0x80000000
 
-#define CFG_SDRAM_BASE		0x00000000
-#define CFG_SRAM_BASE		0x80100000	/* CS 1 */
-#define CFG_DISPLAY_BASE	0x80600000	/* CS 3 */
-#define	CFG_IB_MASTER		0xc0510000	/* CS 6 */
-#define CFG_IB_EPLD		0xc0500000	/* CS 7 */
+#define CONFIG_SYS_SDRAM_BASE		0x00000000
+#define CONFIG_SYS_SRAM_BASE		0x80100000	/* CS 1 */
+#define CONFIG_SYS_DISPLAY_BASE	0x80600000	/* CS 3 */
+#define	CONFIG_SYS_IB_MASTER		0xc0510000	/* CS 6 */
+#define CONFIG_SYS_IB_EPLD		0xc0500000	/* CS 7 */
 
 /* Settings for XLB = 132 MHz */
 #define SDRAM_DDR	 1
@@ -202,32 +202,32 @@
 #define SDRAM_TAPDELAY  0x10000000
 
 /* SRAM */
-#define SRAM_BASE		CFG_SRAM_BASE	/* SRAM base address	*/
+#define SRAM_BASE		CONFIG_SYS_SRAM_BASE	/* SRAM base address	*/
 #define SRAM_LEN		0x1fffff
 #define SRAM_END		(SRAM_BASE + SRAM_LEN)
 
 /* Use ON-Chip SRAM until RAM will be available */
-#define CFG_INIT_RAM_ADDR	MPC5XXX_SRAM
+#define CONFIG_SYS_INIT_RAM_ADDR	MPC5XXX_SRAM
 #ifdef CONFIG_POST
 /* preserve space for the post_word at end of on-chip SRAM */
-#define CFG_INIT_RAM_END	MPC5XXX_SRAM_POST_SIZE
+#define CONFIG_SYS_INIT_RAM_END	MPC5XXX_SRAM_POST_SIZE
 #else
-#define CFG_INIT_RAM_END	MPC5XXX_SRAM_SIZE
+#define CONFIG_SYS_INIT_RAM_END	MPC5XXX_SRAM_SIZE
 #endif
 
 
-#define CFG_GBL_DATA_SIZE	128	/* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_GBL_DATA_SIZE	128	/* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
-#define CFG_MONITOR_BASE    TEXT_BASE
-#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
-#   define CFG_RAMBOOT		1
+#define CONFIG_SYS_MONITOR_BASE    TEXT_BASE
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+#   define CONFIG_SYS_RAMBOOT		1
 #endif
 
-#define CFG_MONITOR_LEN		(192 << 10)	/* Reserve 192 kB for Monitor	*/
-#define CFG_MALLOC_LEN		(512 << 10)	/* Reserve 128 kB for malloc()	*/
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+#define CONFIG_SYS_MONITOR_LEN		(192 << 10)	/* Reserve 192 kB for Monitor	*/
+#define CONFIG_SYS_MALLOC_LEN		(512 << 10)	/* Reserve 128 kB for malloc()	*/
+#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 
 /*
  * Ethernet configuration
@@ -239,7 +239,7 @@
 /*
  * GPIO configuration
  */
-#define CFG_GPS_PORT_CONFIG	0x4d558044
+#define CONFIG_SYS_GPS_PORT_CONFIG	0x4d558044
 
 /*use  Hardware WDT */
 #define CONFIG_HW_WATCHDOG
@@ -247,30 +247,30 @@
 /*
  * Miscellaneous configurable options
  */
-#define CFG_LONGHELP			/* undef to save memory	    */
-#define CFG_PROMPT		"=> "	/* Monitor Command Prompt   */
+#define CONFIG_SYS_LONGHELP			/* undef to save memory	    */
+#define CONFIG_SYS_PROMPT		"=> "	/* Monitor Command Prompt   */
 #if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE		1024	/* Console I/O Buffer Size  */
+#define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size  */
 #else
-#define CFG_CBSIZE		256	/* Console I/O Buffer Size  */
+#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size  */
 #endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS		16	/* max number of command args	*/
-#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS		16	/* max number of command args	*/
+#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
 
 /* Enable an alternate, more extensive memory test */
-#define CFG_ALT_MEMTEST
+#define CONFIG_SYS_ALT_MEMTEST
 
-#define CFG_MEMTEST_START	0x00300000	/* memtest works on */
-#define CFG_MEMTEST_END		0x00f00000	/* 3 ... 15 MB in DRAM	*/
+#define CONFIG_SYS_MEMTEST_START	0x00300000	/* memtest works on */
+#define CONFIG_SYS_MEMTEST_END		0x00f00000	/* 3 ... 15 MB in DRAM	*/
 
-#define CFG_LOAD_ADDR		0x300000	/* default load address */
+#define CONFIG_SYS_LOAD_ADDR		0x300000	/* default load address */
 
-#define CFG_HZ			1000	/* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_HZ			1000	/* decrementer freq: 1 ms ticks */
 
-#define CFG_CACHELINE_SIZE	32	/* For MPC5xxx CPUs			*/
+#define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC5xxx CPUs			*/
 #if defined(CONFIG_CMD_KGDB)
-#  define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
+#  define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
 #endif
 
 /*
@@ -282,41 +282,41 @@
  * Various low-level settings
  */
 #if defined(CONFIG_MPC5200)
-#define CFG_HID0_INIT		HID0_ICE | HID0_ICFI
-#define CFG_HID0_FINAL		HID0_ICE
+#define CONFIG_SYS_HID0_INIT		HID0_ICE | HID0_ICFI
+#define CONFIG_SYS_HID0_FINAL		HID0_ICE
 #else
-#define CFG_HID0_INIT		0
-#define CFG_HID0_FINAL		0
+#define CONFIG_SYS_HID0_INIT		0
+#define CONFIG_SYS_HID0_FINAL		0
 #endif
 
-#define CFG_BOOTCS_START	CFG_FLASH_BASE
-#define CFG_BOOTCS_SIZE		CFG_FLASH_SIZE
-#define CFG_BOOTCS_CFG		0x00045D00
-#define CFG_CS0_START		CFG_FLASH_BASE
-#define CFG_CS0_SIZE		CFG_FLASH_SIZE
+#define CONFIG_SYS_BOOTCS_START	CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_BOOTCS_SIZE		CONFIG_SYS_FLASH_SIZE
+#define CONFIG_SYS_BOOTCS_CFG		0x00045D00
+#define CONFIG_SYS_CS0_START		CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_CS0_SIZE		CONFIG_SYS_FLASH_SIZE
 
 /* 8Mbit SRAM @0x80100000 */
-#define CFG_CS1_START		CFG_SRAM_BASE
-#define CFG_CS1_SIZE		0x00200000
-#define CFG_CS1_CFG		0x21D00
+#define CONFIG_SYS_CS1_START		CONFIG_SYS_SRAM_BASE
+#define CONFIG_SYS_CS1_SIZE		0x00200000
+#define CONFIG_SYS_CS1_CFG		0x21D00
 
 /* Display H1, Status Inputs, EPLD @0x80600000 8 Bit */
-#define CFG_CS3_START		CFG_DISPLAY_BASE
-#define CFG_CS3_SIZE		0x00000100
-#define CFG_CS3_CFG		0x00081802
+#define CONFIG_SYS_CS3_START		CONFIG_SYS_DISPLAY_BASE
+#define CONFIG_SYS_CS3_SIZE		0x00000100
+#define CONFIG_SYS_CS3_CFG		0x00081802
 
 /* Interbus Master 16 Bit */
-#define CFG_CS6_START		CFG_IB_MASTER
-#define CFG_CS6_SIZE		0x00010000
-#define CFG_CS6_CFG		0x00FF3500
+#define CONFIG_SYS_CS6_START		CONFIG_SYS_IB_MASTER
+#define CONFIG_SYS_CS6_SIZE		0x00010000
+#define CONFIG_SYS_CS6_CFG		0x00FF3500
 
 /* Interbus EPLD 8 Bit */
-#define CFG_CS7_START		CFG_IB_EPLD
-#define CFG_CS7_SIZE		0x00010000
-#define CFG_CS7_CFG		0x00081800
+#define CONFIG_SYS_CS7_START		CONFIG_SYS_IB_EPLD
+#define CONFIG_SYS_CS7_SIZE		0x00010000
+#define CONFIG_SYS_CS7_CFG		0x00081800
 
-#define CFG_CS_BURST		0x00000000
-#define CFG_CS_DEADCYCLE	0x33333333
+#define CONFIG_SYS_CS_BURST		0x00000000
+#define CONFIG_SYS_CS_DEADCYCLE	0x33333333
 
 /*-----------------------------------------------------------------------
  * IDE/ATA stuff Supports IDE harddisk
@@ -328,33 +328,33 @@
 #undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE    not supported	*/
 #undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/
 
-#define CFG_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
-#define CFG_IDE_MAXDEVICE	2	/* max. 2 drives per IDE bus	*/
+#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
+#define CONFIG_SYS_IDE_MAXDEVICE	2	/* max. 2 drives per IDE bus	*/
 
 #define CONFIG_IDE_PREINIT	1
 
-#define CFG_ATA_IDE0_OFFSET	0x0000
+#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
 
-#define CFG_ATA_BASE_ADDR	MPC5XXX_ATA
+#define CONFIG_SYS_ATA_BASE_ADDR	MPC5XXX_ATA
 
 /* Offset for data I/O			*/
-#define CFG_ATA_DATA_OFFSET	(0x0060)
+#define CONFIG_SYS_ATA_DATA_OFFSET	(0x0060)
 
 /* Offset for normal register accesses	*/
-#define CFG_ATA_REG_OFFSET	(CFG_ATA_DATA_OFFSET)
+#define CONFIG_SYS_ATA_REG_OFFSET	(CONFIG_SYS_ATA_DATA_OFFSET)
 
 /* Offset for alternate registers	*/
-#define CFG_ATA_ALT_OFFSET	(0x005C)
+#define CONFIG_SYS_ATA_ALT_OFFSET	(0x005C)
 
 /* Interval between registers                                                */
-#define CFG_ATA_STRIDE          4
+#define CONFIG_SYS_ATA_STRIDE          4
 
 #define CONFIG_ATAPI            1
 
 /*---------------------------------------------------------------------*/
 /* Display addresses						       */
 /*---------------------------------------------------------------------*/
-#define CFG_DISP_CHR_RAM	(CFG_DISPLAY_BASE + 0x38)
-#define CFG_DISP_CWORD		(CFG_DISPLAY_BASE + 0x30)
+#define CONFIG_SYS_DISP_CHR_RAM	(CONFIG_SYS_DISPLAY_BASE + 0x38)
+#define CONFIG_SYS_DISP_CWORD		(CONFIG_SYS_DISPLAY_BASE + 0x30)
 
 #endif /* __CONFIG_H */