powerpc: manroland: remove uc100, uc101, mucmc52, hmi1001 support

These boards are still non-generic boards.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefan Roese <sr@denx.de>

1 files changed, 0 insertions, 339 deletions

diff --git a/include/configs/hmi1001.h b/include/configs/hmi1001.h
deleted file mode 100644
index a1a88b5e330..00000000000
--- a/include/configs/hmi1001.h
+++ /dev/null
@@ -1,339 +0,0 @@
-/*
- * (C) Copyright 2003-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC5200		1	/* This is an MPC5200 CPU	*/
-#define CONFIG_HMI1001		1	/* HMI1001 board		*/
-
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE	0xFFF00000
-#endif
-
-#define CONFIG_SYS_MPC5XXX_CLKIN	33000000 /* ... running at 33.000000MHz		*/
-
-#define CONFIG_BOARD_EARLY_INIT_R
-
-#define CONFIG_HIGH_BATS	1	/* High BATs supported			*/
-
-/*
- * Serial console configuration
- */
-#define CONFIG_PSC_CONSOLE	1	/* console is on PSC1	*/
-#define CONFIG_BAUDRATE		115200	/* ... at 115200 bps	*/
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
-
-/* Partitions */
-#define CONFIG_DOS_PARTITION
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DISPLAY
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_SNTP
-
-
-#define	CONFIG_TIMESTAMP	1	/* Print image info with timestamp */
-
-#if (CONFIG_SYS_TEXT_BASE == 0xFFF00000) /* Boot low */
-#   define CONFIG_SYS_LOWBOOT		1
-#endif
-
-/*
- * Autobooting
- */
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds */
-
-#define CONFIG_PREBOOT	"echo;" \
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"flash_nfs=run nfsargs addip;"					\
-		"bootm ${kernel_addr}\0"				\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
-	"rootpath=/opt/eldk/ppc_82xx\0"					\
-	""
-
-#define CONFIG_BOOTCOMMAND	"run net_nfs"
-
-#define CONFIG_MISC_INIT_R	1
-
-/*
- * IPB Bus clocking configuration.
- */
-#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK		/* define for 133MHz speed */
-
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE		2	/* Select I2C module #1 or #2 */
-
-#define CONFIG_SYS_I2C_SPEED		100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x58
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	4
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10
-
-/*
- * RTC configuration
- */
-#define CONFIG_RTC_PCF8563
-#define CONFIG_SYS_I2C_RTC_ADDR		0x51
-
-/*
- * Flash configuration
- */
-#define CONFIG_SYS_FLASH_BASE		0xFF800000
-
-#define CONFIG_SYS_FLASH_SIZE		0x00800000 /* 8 MByte */
-#define CONFIG_SYS_MAX_FLASH_SECT	67	/* max num of sects on one chip */
-
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_TEXT_BASE+0x40000) /* second sector */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max num of flash banks
-					   (= chip selects) */
-#define CONFIG_SYS_FLASH_ERASE_TOUT	240000	/* Flash Erase Timeout (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (in ms)	*/
-
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_CFI_AMD_RESET
-
-/*
- * Environment settings
- */
-#define CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_SIZE		0x4000
-#define CONFIG_ENV_SECT_SIZE	0x20000
-#define CONFIG_ENV_OFFSET_REDUND   (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND     (CONFIG_ENV_SIZE)
-
-/*
- * Memory map
- */
-#define CONFIG_SYS_MBAR		0xF0000000
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_DEFAULT_MBAR	0x80000000
-#define CONFIG_SYS_DISPLAY_BASE	0x80600000
-#define CONFIG_SYS_STATUS1_BASE	0x80600200
-#define CONFIG_SYS_STATUS2_BASE	0x80600300
-
-/* Settings for XLB = 132 MHz */
-#define SDRAM_DDR	 1
-#define SDRAM_MODE      0x018D0000
-#define SDRAM_EMODE     0x40090000
-#define SDRAM_CONTROL   0x714f0f00
-#define SDRAM_CONFIG1   0x73722930
-#define SDRAM_CONFIG2   0x47770000
-#define SDRAM_TAPDELAY  0x10000000
-
-/* Use ON-Chip SRAM until RAM will be available */
-#define CONFIG_SYS_INIT_RAM_ADDR	MPC5XXX_SRAM
-
-/* preserve space for the post_word at end of on-chip SRAM */
-#define MPC5XXX_SRAM_POST_SIZE (MPC5XXX_SRAM_SIZE - 4)
-
-#ifdef CONFIG_POST
-#define CONFIG_SYS_INIT_RAM_SIZE	MPC5XXX_SRAM_POST_SIZE
-#else
-#define CONFIG_SYS_INIT_RAM_SIZE	MPC5XXX_SRAM_SIZE
-#endif
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_BASE    CONFIG_SYS_TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#   define CONFIG_SYS_RAMBOOT		1
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN		(192 << 10)	/* Reserve 192 kB for Monitor	*/
-#define CONFIG_SYS_MALLOC_LEN		(512 << 10)	/* Reserve 128 kB for malloc()	*/
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-/*
- * Ethernet configuration
- */
-#define CONFIG_MPC5xxx_FEC	1
-#define CONFIG_MPC5xxx_FEC_MII100
-#define CONFIG_PHY_ADDR		0x00
-#define CONFIG_MII		1		/* MII PHY management		*/
-
-/*
- * GPIO configuration
- */
-#define CONFIG_SYS_GPS_PORT_CONFIG	0x01051004
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory	    */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size  */
-#else
-#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size  */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS		16	/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC5xxx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#  define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
-/* Enable an alternate, more extensive memory test */
-#define CONFIG_SYS_ALT_MEMTEST
-
-#define CONFIG_SYS_MEMTEST_START	0x00100000	/* memtest works on */
-#define CONFIG_SYS_MEMTEST_END		0x00f00000	/* 1 ... 15 MB in DRAM	*/
-
-#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
-
-/*
- * Enable loopw command.
- */
-#define CONFIG_LOOPW
-
-/*
- * Various low-level settings
- */
-#define CONFIG_SYS_HID0_INIT		HID0_ICE | HID0_ICFI
-#define CONFIG_SYS_HID0_FINAL		HID0_ICE
-
-#define CONFIG_SYS_BOOTCS_START	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_BOOTCS_SIZE		CONFIG_SYS_FLASH_SIZE
-#define CONFIG_SYS_BOOTCS_CFG		0x0004FB00
-#define CONFIG_SYS_CS0_START		CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_CS0_SIZE		CONFIG_SYS_FLASH_SIZE
-
-/* 8Mbit SRAM @0x80100000 */
-#define CONFIG_SYS_CS1_START		0x80100000
-#define CONFIG_SYS_CS1_SIZE		0x00100000
-#define CONFIG_SYS_CS1_CFG		0x19B00
-
-/* FRAM 32Kbyte @0x80700000 */
-#define CONFIG_SYS_CS2_START		0x80700000
-#define CONFIG_SYS_CS2_SIZE		0x00008000
-#define CONFIG_SYS_CS2_CFG		0x19800
-
-/* Display H1, Status Inputs, EPLD @0x80600000 */
-#define CONFIG_SYS_CS3_START		0x80600000
-#define CONFIG_SYS_CS3_SIZE		0x00100000
-#define CONFIG_SYS_CS3_CFG		0x00019800
-
-#define CONFIG_SYS_CS_BURST		0x00000000
-#define CONFIG_SYS_CS_DEADCYCLE	0x33333333
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff Supports IDE harddisk
- *-----------------------------------------------------------------------
- */
-
-#undef  CONFIG_IDE_8xx_PCCARD		/* Use IDE with PC Card	Adapter	*/
-
-#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE    not supported	*/
-#undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/
-
-#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
-#define CONFIG_SYS_IDE_MAXDEVICE	2	/* max. 2 drives per IDE bus	*/
-
-#define CONFIG_IDE_PREINIT	1
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR	MPC5XXX_ATA
-
-/* Offset for data I/O			*/
-#define CONFIG_SYS_ATA_DATA_OFFSET	(0x0060)
-
-/* Offset for normal register accesses	*/
-#define CONFIG_SYS_ATA_REG_OFFSET	(CONFIG_SYS_ATA_DATA_OFFSET)
-
-/* Offset for alternate registers	*/
-#define CONFIG_SYS_ATA_ALT_OFFSET	(0x005C)
-
-/* Interval between registers                                                */
-#define CONFIG_SYS_ATA_STRIDE          4
-
-#define CONFIG_ATAPI            1
-
-#define CONFIG_VIDEO_SMI_LYNXEM
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#define CONFIG_VIDEO_LOGO
-
-/*
- * PCI Mapping:
- * 0x40000000 - 0x4fffffff - PCI Memory
- * 0x50000000 - 0x50ffffff - PCI IO Space
- */
-#define CONFIG_PCI		1
-#define CONFIG_PCI_PNP		1
-#define CONFIG_PCI_SCAN_SHOW	1
-#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE	1
-
-#define CONFIG_PCI_MEM_BUS	0x40000000
-#define CONFIG_PCI_MEM_PHYS	CONFIG_PCI_MEM_BUS
-#define CONFIG_PCI_MEM_SIZE	0x10000000
-
-#define CONFIG_PCI_IO_BUS	0x50000000
-#define CONFIG_PCI_IO_PHYS	CONFIG_PCI_IO_BUS
-#define CONFIG_PCI_IO_SIZE	0x01000000
-
-#define CONFIG_SYS_ISA_IO		CONFIG_PCI_IO_BUS
-
-/*---------------------------------------------------------------------*/
-/* Display addresses						       */
-/*---------------------------------------------------------------------*/
-
-#define CONFIG_PDSP188x
-#define CONFIG_SYS_DISP_CHR_RAM	(CONFIG_SYS_DISPLAY_BASE + 0x38)
-#define CONFIG_SYS_DISP_CWORD		(CONFIG_SYS_DISPLAY_BASE + 0x30)
-
-#endif /* __CONFIG_H */