Blackfin: unify common ADI board settings

Rather than duplicate the same ADI settings in every ADI board, create a
common ADI config header and have all ADI boards start using that.  This
will also make merging the ~10 boards I have to forward port a lot easier.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

1 files changed, 142 insertions, 294 deletions

diff --git a/include/configs/bf533-stamp.h b/include/configs/bf533-stamp.h
index ee41c7e78f8..622f54c38c2 100644
--- a/include/configs/bf533-stamp.h
+++ b/include/configs/bf533-stamp.h
@@ -2,371 +2,219 @@
  * U-boot - Configuration file for BF533 STAMP board
  */
 
-#ifndef __CONFIG_STAMP_H__
-#define __CONFIG_STAMP_H__
+#ifndef __CONFIG_BF533_STAMP_H__
+#define __CONFIG_BF533_STAMP_H__
 
 #include <asm/blackfin-config-pre.h>
 
-#define CONFIG_RTC_BFIN			1
-
-#define CONFIG_PANIC_HANG 1
-
-#define CONFIG_BFIN_CPU	bf533-0.3
-#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
-
-/* This sets the default state of the cache on U-Boot's boot */
-#define CONFIG_ICACHE_ON
-#define CONFIG_DCACHE_ON
 
 /*
- * Board settings
+ * Processor Settings
  */
-#define CONFIG_DRIVER_SMC91111	1
-#define CONFIG_SMC91111_BASE	0x20300300
-
-/* FLASH/ETHERNET uses the same address range */
-#define SHARED_RESOURCES	1
+#define CONFIG_BFIN_CPU             bf533-0.3
+#define CONFIG_BFIN_BOOT_MODE       BFIN_BOOT_BYPASS
 
-/* Is I2C bit-banged? */
-#define CONFIG_SOFT_I2C		1
 
 /*
- * Software (bit-bang) I2C driver configuration
+ * Clock Settings
+ *	CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
+ *	SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
  */
-#define PF_SCL			PF3
-#define PF_SDA			PF2
+/* CONFIG_CLKIN_HZ is any value in Hz					*/
+#define CONFIG_CLKIN_HZ			11059200
+/* CLKIN_HALF controls the DF bit in PLL_CTL      0 = CLKIN		*/
+/*                                                1 = CLKIN / 2		*/
+#define CONFIG_CLKIN_HALF		0
+/* PLL_BYPASS controls the BYPASS bit in PLL_CTL  0 = do not bypass	*/
+/*                                                1 = bypass PLL	*/
+#define CONFIG_PLL_BYPASS		0
+/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL		*/
+/* Values can range from 0-63 (where 0 means 64)			*/
+#define CONFIG_VCO_MULT			36
+/* CCLK_DIV controls the core clock divider				*/
+/* Values can be 1, 2, 4, or 8 ONLY					*/
+#define CONFIG_CCLK_DIV			1
+/* SCLK_DIV controls the system clock divider				*/
+/* Values can range from 1-15						*/
+#define CONFIG_SCLK_DIV			5
 
-/*
- * Video splash screen support
- */
-#define  CONFIG_VIDEO		0
 
 /*
- * Clock settings
+ * Memory Settings
  */
+#define CONFIG_MEM_ADD_WDTH	11
+#define CONFIG_MEM_SIZE		128
 
-/* CONFIG_CLKIN_HZ is any value in Hz				*/
-#define CONFIG_CLKIN_HZ		11059200
-/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN	*/
-/*						    1=CLKIN/2	*/
-#define CONFIG_CLKIN_HALF	0
-/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass	*/
-/*						 1=bypass PLL	*/
-#define CONFIG_PLL_BYPASS	0
-/* CONFIG_VCO_MULT controls what the multiplier of the PLL is.	*/
-/* Values can range from 1-64					*/
-#define CONFIG_VCO_MULT		36
-/* CONFIG_CCLK_DIV controls what the core clock divider is	*/
-/* Values can be 1, 2, 4, or 8 ONLY				*/
-#define CONFIG_CCLK_DIV		1
-/* CONFIG_SCLK_DIV controls what the peripheral clock divider is*/
-/* Values can range from 1-15					*/
-#define CONFIG_SCLK_DIV		5
-/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider	*/
-/* Values can range from 2-65535				*/
-/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD)			*/
-#define CONFIG_SPI_BAUD		2
-#define CONFIG_SPI_BAUD_INITBLOCK	4
-
-/*
- * Network settings
- */
+#define CONFIG_EBIU_SDRRC_VAL	0x268
+#define CONFIG_EBIU_SDGCTL_VAL	0x911109
 
-#if (CONFIG_DRIVER_SMC91111)
-#if 0
-#define	CONFIG_MII
-#endif
+#define CONFIG_EBIU_AMGCTL_VAL	0xFF
+#define CONFIG_EBIU_AMBCTL0_VAL	0xBBC3BBC3
+#define CONFIG_EBIU_AMBCTL1_VAL	0x99B39983
 
-/* network support */
-#define CONFIG_IPADDR		192.168.0.15
-#define CONFIG_NETMASK		255.255.255.0
-#define CONFIG_GATEWAYIP	192.168.0.1
-#define CONFIG_SERVERIP		192.168.0.2
-#define CONFIG_HOSTNAME		STAMP
-#define CONFIG_ROOTPATH		/checkout/uClinux-dist/romfs
+#define CONFIG_SYS_MONITOR_LEN	(256 * 1024)
+#define CONFIG_SYS_MALLOC_LEN	(384 * 1024)
 
-/* To remove hardcoding and enable MAC storage in EEPROM  */
-/* #define CONFIG_ETHADDR		02:80:ad:20:31:b8 */
-#endif /* CONFIG_DRIVER_SMC91111 */
 
 /*
- * Flash settings
+ * Network Settings
  */
+#define ADI_CMDS_NETWORK	1
+#define CONFIG_DRIVER_SMC91111	1
+#define CONFIG_SMC91111_BASE	0x20300300
+#define SMC91111_EEPROM_INIT() \
+	do { \
+		*pFIO_DIR |= PF1; \
+		*pFIO_FLAG_S = PF1; \
+		SSYNC(); \
+	} while (0)
+#define CONFIG_HOSTNAME		bf533-stamp
+/* Uncomment next line to use fixed MAC address */
+/* #define CONFIG_ETHADDR	02:80:ad:20:31:b8 */
 
-#define CONFIG_SYS_FLASH_CFI		/* The flash is CFI compatible  */
-#define CONFIG_FLASH_CFI_DRIVER	/* Use common CFI driver	*/
-#define	CONFIG_SYS_FLASH_CFI_AMD_RESET
-
-#define CONFIG_SYS_FLASH_BASE		0x20000000
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	67	/* max number of sectors on one chip */
-
-#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER)
-#define CONFIG_ENV_IS_IN_EEPROM	1
-#define CONFIG_ENV_OFFSET		0x4000
-#define CONFIG_ENV_HEADER		(CONFIG_ENV_OFFSET + 0x12A)	/* 0x12A is the length of LDR file header */
-#else
-#define CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_ADDR		0x20004000
-#define	CONFIG_ENV_OFFSET		(CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE)
-#endif
-
-#define	CONFIG_ENV_SIZE		0x2000
-#define CONFIG_ENV_SECT_SIZE	0x2000	/* Total Size of Environment Sector */
-#define	ENV_IS_EMBEDDED
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	30000	/* Timeout for Chip Erase (in ms) */
-#define CONFIG_SYS_FLASH_ERASEBLOCK_TOUT	5000	/* Timeout for Block Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	1	/* Timeout for Flash Write (in ms) */
-
-/* JFFS Partition offset set  */
-#define CONFIG_SYS_JFFS2_FIRST_BANK 0
-#define CONFIG_SYS_JFFS2_NUM_BANKS  1
-/* 512k reserved for u-boot */
-#define CONFIG_SYS_JFFS2_FIRST_SECTOR	11
-
-/*
- * following timeouts shall be used once the
- * Flash real protection is enabled
- */
-#define CONFIG_SYS_FLASH_LOCK_TOUT	5	/* Timeout for Flash Set Lock Bit (in ms) */
-#define CONFIG_SYS_FLASH_UNLOCK_TOUT	10000	/* Timeout for Flash Clear Lock Bits (in ms) */
-
-/*
- * SDRAM settings & memory map
- */
-
-#define CONFIG_MEM_SIZE		128	/* 128, 64, 32, 16 */
-#define CONFIG_MEM_ADD_WDTH     11	/* 8, 9, 10, 11    */
-#define CONFIG_MEM_MT48LC64M4A2FB_7E	1
-
-#define CONFIG_SYS_MEMTEST_START	0x00000000	/* memtest works on */
-
-#define	CONFIG_SYS_SDRAM_BASE		0x00000000
-
-#define CONFIG_SYS_MAX_RAM_SIZE	(CONFIG_MEM_SIZE * 1024 *1024)
-#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MAX_RAM_SIZE - 0x80000 - 1)
-#define CONFIG_LOADADDR		0x01000000
-
-#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
-#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#define CONFIG_SYS_MALLOC_LEN		(128 << 10)     /* Reserve 128 kB for malloc()	*/
-#define CONFIG_SYS_GBL_DATA_SIZE	0x4000		/* Reserve 16k for Global Data  */
-#define CONFIG_STACKSIZE	(128*1024)	/* regular stack */
-
-#define CONFIG_SYS_MONITOR_BASE		(CONFIG_SYS_MAX_RAM_SIZE - 0x40000)
-#define CONFIG_SYS_MALLOC_BASE		(CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN)
-#define CONFIG_SYS_GBL_DATA_ADDR	(CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_STACKBASE	(CONFIG_SYS_GBL_DATA_ADDR  - 4)
-
-/* Check to make sure everything fits in SDRAM */
-#if ((CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) > CONFIG_SYS_MAX_RAM_SIZE)
-	#error Memory Map does not fit into configuration
-#endif
-
-#if ( CONFIG_CLKIN_HALF == 0 )
-#define CONFIG_VCO_HZ		( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
-#else
-#define CONFIG_VCO_HZ		(( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
-#endif
-
-#if (CONFIG_PLL_BYPASS == 0)
-#define CONFIG_CCLK_HZ		( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
-#define CONFIG_SCLK_HZ		( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
-#else
-#define CONFIG_CCLK_HZ		CONFIG_CLKIN_HZ
-#define CONFIG_SCLK_HZ		CONFIG_CLKIN_HZ
-#endif
 
 /*
- * Command settings
+ * Flash Settings
  */
-
-#define CONFIG_SYS_LONGHELP		1
-#define CONFIG_CMDLINE_EDITING	1
-
-#define CONFIG_SYS_AUTOLOAD		"no"	/*rarpb, bootp or dhcp commands will perform only a */
-
-/* configuration lookup from the BOOTP/DHCP server, */
-/* but not try to load any image using TFTP	    */
-
-#define CONFIG_BOOTDELAY	5
-#define CONFIG_BOOT_RETRY_TIME	-1	/* Enable this if bootretry required, currently its disabled */
-#define CONFIG_BOOTCOMMAND	"run ramboot"
-
-#define CONFIG_BOOTARGS		"root=/dev/mtdblock0 rw console=ttyBF0,57600"
-
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
-	"ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
-	"nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):" \
-		"$(rootpath) console=ttyBF0,57600\0" \
-	"addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \
-		"$(gatewayip):$(netmask):$(hostname):eth0:off\0" \
-	"ramboot=tftpboot $(loadaddr) linux; " \
-		"run ramargs;run addip;bootelf\0" \
-	"nfsboot=tftpboot $(loadaddr) linux; " \
-		"run nfsargs;run addip;bootelf\0" \
-	"flashboot=bootm 0x20100000\0" \
-	"update=tftpboot $(loadaddr) u-boot.bin; " \
-		"protect off 0x20000000 0x2003FFFF; erase 0x20000000 0x2003FFFF;" \
-		"cp.b $(loadaddr) 0x20000000 $(filesize)\0" \
-	""
-
-#ifdef CONFIG_SOFT_I2C
-#if (!CONFIG_SOFT_I2C)
-#undef CONFIG_SOFT_I2C
-#endif
-#endif
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_BASE		0x20000000
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_CFI_AMD_RESET
+#define CONFIG_SYS_MAX_FLASH_BANKS	1
+#define CONFIG_SYS_MAX_FLASH_SECT	67
 
 
 /*
- * BOOTP options
+ * SPI Settings
  */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BFIN_SPI
+#define CONFIG_ENV_SPI_MAX_HZ	30000000
+#define CONFIG_SF_DEFAULT_HZ	30000000
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_ATMEL
+#define CONFIG_SPI_FLASH_SPANSION
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_SPI_FLASH_WINBOND
 
 
 /*
- * Command line configuration.
+ * Env Storage Settings
  */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_DATE
-
-#if (CONFIG_DRIVER_SMC91111)
-#define CONFIG_CMD_PING
-#endif
-
-#if (CONFIG_SOFT_I2C)
-#define CONFIG_CMD_I2C
+#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER)
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_OFFSET	0x4000
+#define CONFIG_ENV_SIZE		0x2000
+#define CONFIG_ENV_SECT_SIZE	0x2000
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_OFFSET	0x4000
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
+#define CONFIG_ENV_SIZE		0x2000
+#define CONFIG_ENV_SECT_SIZE	0x2000
 #endif
-
-#define CONFIG_CMD_DHCP
-
-
-/*
- * Console settings
- */
-
-#define CONFIG_BAUDRATE		57600
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
-
-#define	CONFIG_SYS_PROMPT		"bfin> "	/* Monitor Command Prompt */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
+#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS)
+#define ENV_IS_EMBEDDED
 #else
-#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
+#define ENV_IS_EMBEDDED_CUSTOM
 #endif
-#define CONFIG_SYS_PBSIZE	(CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
 
-#define CONFIG_LOADS_ECHO	1
 
 /*
- * I2C settings
+ * I2C Settings
  * By default PF2 is used as SDA and PF3 as SCL on the Stamp board
  */
-#if (CONFIG_SOFT_I2C)
-
-#define I2C_INIT		(*pFIO_DIR |=  PF_SCL); asm("ssync;")
-#define I2C_ACTIVE		(*pFIO_DIR |=  PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;")
-#define I2C_TRISTATE		(*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;")
-#define I2C_READ		((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;")
-#define I2C_SDA(bit)	if(bit) { \
-				*pFIO_FLAG_S = PF_SDA; \
-				asm("ssync;"); \
-				} \
-			else	{ \
-				*pFIO_FLAG_C = PF_SDA; \
-				asm("ssync;"); \
-				}
-#define I2C_SCL(bit)	if(bit) { \
-				*pFIO_FLAG_S = PF_SCL; \
-				asm("ssync;"); \
-				} \
-			else	{ \
-				*pFIO_FLAG_C = PF_SCL; \
-				asm("ssync;"); \
-				}
+#define CONFIG_SOFT_I2C
+#ifdef CONFIG_SOFT_I2C
+#define PF_SCL PF3
+#define PF_SDA PF2
+#define I2C_INIT \
+	do { \
+		*pFIO_DIR |= PF_SCL; \
+		SSYNC(); \
+	} while (0)
+#define I2C_ACTIVE \
+	do { \
+		*pFIO_DIR |= PF_SDA; \
+		*pFIO_INEN &= ~PF_SDA; \
+		SSYNC(); \
+	} while (0)
+#define I2C_TRISTATE \
+	do { \
+		*pFIO_DIR &= ~PF_SDA; \
+		*pFIO_INEN |= PF_SDA; \
+		SSYNC(); \
+	} while (0)
+#define I2C_READ ((*pFIO_FLAG_D & PF_SDA) != 0)
+#define I2C_SDA(bit) \
+	do { \
+		if (bit) \
+			*pFIO_FLAG_S = PF_SDA; \
+		else \
+			*pFIO_FLAG_C = PF_SDA; \
+		SSYNC(); \
+	} while (0)
+#define I2C_SCL(bit) \
+	do { \
+		if (bit) \
+			*pFIO_FLAG_S = PF_SCL; \
+		else \
+			*pFIO_FLAG_C = PF_SCL; \
+		SSYNC(); \
+	} while (0)
 #define I2C_DELAY		udelay(5)	/* 1/4 I2C clock duration */
 
 #define CONFIG_SYS_I2C_SPEED		50000
 #define CONFIG_SYS_I2C_SLAVE		0
-#endif /* CONFIG_SOFT_I2C */
+#endif
+
 
 /*
- * Compact Flash settings
+ * Compact Flash / IDE / ATA Settings
  */
 
 /* Enabled below option for CF support */
-/* #define CONFIG_STAMP_CF	1 */
-
-#if defined(CONFIG_STAMP_CF) && defined(CONFIG_CMD_IDE)
-
-#define CONFIG_MISC_INIT_R	1
+/* #define CONFIG_STAMP_CF */
+#if defined(CONFIG_STAMP_CF)
+#define CONFIG_MISC_INIT_R
 #define CONFIG_DOS_PARTITION	1
-/*
- * IDE/ATA stuff
- */
 #undef  CONFIG_IDE_8xx_DIRECT		/* no pcmcia interface required */
 #undef  CONFIG_IDE_LED			/* no led for ide supported */
 #undef  CONFIG_IDE_RESET		/* no reset for ide supported */
 
-#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE busses */
-#define CONFIG_SYS_IDE_MAXDEVICE	(CONFIG_SYS_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
+#define CONFIG_SYS_IDE_MAXBUS		1
+#define CONFIG_SYS_IDE_MAXDEVICE	(CONFIG_SYS_IDE_MAXBUS * 1)
 
 #define CONFIG_SYS_ATA_BASE_ADDR	0x20200000
 #define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
 
-#define CONFIG_SYS_ATA_DATA_OFFSET	0x0020	/* Offset for data I/O */
-#define CONFIG_SYS_ATA_REG_OFFSET	0x0020	/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x0007	/* Offset for alternate registers */
+#define CONFIG_SYS_ATA_DATA_OFFSET	0x0020	/* data I/O */
+#define CONFIG_SYS_ATA_REG_OFFSET	0x0020	/* normal register accesses */
+#define CONFIG_SYS_ATA_ALT_OFFSET	0x0007	/* alternate registers */
 
 #define CONFIG_SYS_ATA_STRIDE		2
+
+#undef CONFIG_EBIU_AMBCTL1_VAL
+#define CONFIG_EBIU_AMBCTL1_VAL	0x99B3ffc2
 #endif
 
+
 /*
- * Miscellaneous configurable options
+ * Misc Settings
  */
+#define CONFIG_RTC_BFIN
+#define CONFIG_UART_CONSOLE	0
 
-#define	CONFIG_SYS_HZ			1000	/* 1ms time tick */
-
-#define CONFIG_SYS_BOOTM_LEN		0x4000000/* Large Image Length, set to 64 Meg */
-
-#define CONFIG_SHOW_BOOT_PROGRESS 1	/* Show boot progress on LEDs */
+/* FLASH/ETHERNET uses the same async bank */
+#define SHARED_RESOURCES 	1
 
-#define CONFIG_SPI
+/* define to enable splash screen support */
+/* #define CONFIG_VIDEO */
 
-#ifdef  CONFIG_VIDEO
-#if (CONFIG_VIDEO)
-#define CONFIG_SPLASH_SCREEN	1
-#define CONFIG_SILENT_CONSOLE	1
-#else
-#undef CONFIG_VIDEO
-#endif
-#endif
 
 /*
- * FLASH organization and environment definitions
+ * Pull in common ADI header for remaining command/environment setup
  */
-
-#define CONFIG_EBIU_SDRRC_VAL  0x268
-#define CONFIG_EBIU_SDGCTL_VAL 0x911109
-#define CONFIG_EBIU_SDBCTL_VAL 0x37
-
-#define CONFIG_EBIU_AMGCTL_VAL		0xFF
-#define CONFIG_EBIU_AMBCTL0_VAL		0xBBC3BBC3
-#define CONFIG_EBIU_AMBCTL1_VAL		0x99B39983
-#define CF_CONFIG_EBIU_AMBCTL1_VAL		0x99B3ffc2
+#include <configs/bfin_adi_common.h>
 
 #include <asm/blackfin-config-post.h>