summaryrefslogtreecommitdiff
path: root/include/configs/CPCI405AB.h
diff options
context:
space:
mode:
authorstroese <stroese>2004-12-16 18:05:42 +0000
committerstroese <stroese>2004-12-16 18:05:42 +0000
commita20b27a36b7b1f593e18b4efd506e5f01a392dc6 (patch)
treef9dc45c287966bb96c38a8267d07b217727efb3c /include/configs/CPCI405AB.h
parent44acc8d334a8b9ddb81fc238b094574991f19afa (diff)
esd config files updated
Diffstat (limited to 'include/configs/CPCI405AB.h')
-rw-r--r--include/configs/CPCI405AB.h45
1 files changed, 25 insertions, 20 deletions
diff --git a/include/configs/CPCI405AB.h b/include/configs/CPCI405AB.h
index 3c94ebc349..dee26f8716 100644
--- a/include/configs/CPCI405AB.h
+++ b/include/configs/CPCI405AB.h
@@ -41,27 +41,22 @@
#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
-#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
+#define CONFIG_SYS_CLK_FREQ 33330000 /* external frequency to pll */
#define CONFIG_BAUDRATE 9600
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
-#if 0
-#define CONFIG_PREBOOT \
- "crc32 f0207004 ffc 0;" \
- "if cmp 0 f0207000 1;" \
- "then;echo Old CRC is correct;crc32 f0207004 ff4 f0207000;" \
- "else;echo Old CRC is bad;fi"
-#endif
-
#undef CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND "bootm 100000" /* default boot command */
+#undef CONFIG_BOOTCOMMAND
+
+#define CONFIG_PREBOOT /* enable preboot variable */
#undef CONFIG_LOADS_ECHO /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
#define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */
@@ -75,6 +70,7 @@
CFG_CMD_PCI | \
CFG_CMD_IRQ | \
CFG_CMD_IDE | \
+ CFG_CMD_FAT | \
CFG_CMD_ELF | \
CFG_CMD_DATE | \
CFG_CMD_JFFS2 | \
@@ -86,6 +82,8 @@
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
+#define CONFIG_SUPPORT_VFAT
+
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
@@ -155,6 +153,8 @@
#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
+
#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
@@ -232,13 +232,14 @@
* I2C EEPROM (CAT24WC32) for environment
*/
#define CONFIG_HARD_I2C /* I2c with hardware support */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC32 */
#define CFG_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */
/* mask of address bits that overflow into the "EEPROM chip address" */
#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x01
+#define CFG_I2C_MULTI_EEPROMS 1 /* more than one eeprom used! */
#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* The Catalyst CAT24WC32 has */
/* 32 byte page write mode using*/
/* last 5 bits of the address */
@@ -254,7 +255,7 @@
#define CFG_NVRAM_BASE_ADDR 0xf0200000 /* NVRAM base address */
#define CFG_NVRAM_SIZE (32*1024) /* NVRAM size */
-#define CFG_NVRAM_VXWORKS_OFFS 0x6900 /* Offset for VxWorks eth-addr */
+#define CFG_VXWORKS_MAC_PTR (CFG_NVRAM_BASE_ADDR+0x6900) /* VxWorks eth-addr*/
/*-----------------------------------------------------------------------
* Cache Configuration
@@ -331,16 +332,20 @@
#define CFG_FPGA_MODE_CF_RESET 0x0001
#define CFG_FPGA_MODE_DUART_RESET 0x0002
#define CFG_FPGA_MODE_ENABLE_OUTPUT 0x0004 /* only set on CPCI-405 Ver 3 */
-#define CFG_FPGA_MODE_TS_IRQ_ENABLE 0x0100
-#define CFG_FPGA_MODE_TS_IRQ_CLEAR 0x1000
-#define CFG_FPGA_MODE_TS_CLEAR 0x2000
+#define CFG_FPGA_MODE_1WIRE_DIR 0x0100 /* dir=1 -> output */
+#define CFG_FPGA_MODE_SIM_OK_DIR 0x0200
+#define CFG_FPGA_MODE_TESTRIG_FAIL_DIR 0x0400
+#define CFG_FPGA_MODE_1WIRE 0x1000
+#define CFG_FPGA_MODE_SIM_OK 0x2000 /* wired-or net from all devices */
+#define CFG_FPGA_MODE_TESTRIG_FAIL 0x4000
/* FPGA Status Reg */
-#define CFG_FPGA_STATUS_DIP0 0x0001
-#define CFG_FPGA_STATUS_DIP1 0x0002
-#define CFG_FPGA_STATUS_DIP2 0x0004
-#define CFG_FPGA_STATUS_FLASH 0x0008
-#define CFG_FPGA_STATUS_TS_IRQ 0x1000
+#define CFG_FPGA_STATUS_DIP0 0x0001
+#define CFG_FPGA_STATUS_DIP1 0x0002
+#define CFG_FPGA_STATUS_DIP2 0x0004
+#define CFG_FPGA_STATUS_FLASH 0x0008
+#define CFG_FPGA_STATUS_1WIRE 0x1000
+#define CFG_FPGA_STATUS_SIM_OK 0x2000
#define CFG_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
#define CFG_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S30 */