diff options
| author | pekon gupta <pekon@ti.com> | 2014-05-06 00:46:19 +0530 |
|---|---|---|
| committer | Tom Rini <trini@ti.com> | 2014-06-06 17:46:06 -0400 |
| commit | b80a66033856cc89c62886ae3e5ba54a7faf31ae (patch) | |
| tree | ecf8d57a92382864f8bf75757761961e5c237b72 /drivers | |
| parent | 6e1899e633c2ac3f6da7101d4990361c6ff2a9d2 (diff) | |
mtd: nand: omap: add CONFIG_SYS_NAND_BUSWIDTH_16BIT to indicate NAND device bus-width
GPMC controller needs to be configured based on bus-width of the NAND device
connected to it. Also, dynamic detection of NAND bus-width from on-chip ONFI
parameters is not possible in following situations:
SPL: SPL NAND drivers does not support ONFI parameter reading.
U-boot: GPMC controller iniitalization is done in omap_gpmc.c:board_nand_init()
which is called before probing for devices, hence any ONFI parameter
information is not available during GPMC initialization.
Thus, OMAP NAND driver expected board developers to explicitely write GPMC
configurations specific to NAND device attached on board in board files itself.
But this was troublesome for board manufacturers as they need to dive into
lengthy platform & SoC documents to find details of GPMC registers and
appropriate configurations to get NAND device working.
This patch instead adds existing CONFIG_SYS_NAND_BUSWIDTH_16BIT to board config
hich indicates that connected NAND device has x16 bus-width. And then based on
this config GPMC driver itself initializes itself based on NAND bus-width. This
keeps board developers free from knowing GPMC controller specific internals.
Signed-off-by: Pekon Gupta <pekon@ti.com>
Diffstat (limited to 'drivers')
| -rw-r--r-- | drivers/mtd/nand/omap_gpmc.c | 13 |
1 files changed, 9 insertions, 4 deletions
diff --git a/drivers/mtd/nand/omap_gpmc.c b/drivers/mtd/nand/omap_gpmc.c index d2fedf9fac..cdfa6bc1c9 100644 --- a/drivers/mtd/nand/omap_gpmc.c +++ b/drivers/mtd/nand/omap_gpmc.c @@ -782,13 +782,18 @@ int board_nand_init(struct nand_chip *nand) nand->priv = &omap_nand_info; nand->cmd_ctrl = omap_nand_hwcontrol; nand->options |= NAND_NO_PADDING | NAND_CACHEPRG; - /* If we are 16 bit dev, our gpmc config tells us that */ - if ((readl(&gpmc_cfg->cs[cs].config1) & 0x3000) == 0x1000) - nand->options |= NAND_BUSWIDTH_16; - nand->chip_delay = 100; nand->ecc.layout = &omap_ecclayout; + /* configure driver and controller based on NAND device bus-width */ + gpmc_config = readl(&gpmc_cfg->cs[cs].config1); +#if defined(CONFIG_SYS_NAND_BUSWIDTH_16BIT) + nand->options |= NAND_BUSWIDTH_16; + writel(gpmc_config | (0x1 << 12), &gpmc_cfg->cs[cs].config1); +#else + nand->options &= ~NAND_BUSWIDTH_16; + writel(gpmc_config & ~(0x1 << 12), &gpmc_cfg->cs[cs].config1); +#endif /* select ECC scheme */ #if defined(CONFIG_NAND_OMAP_ECCSCHEME) err = omap_select_ecc_scheme(nand, CONFIG_NAND_OMAP_ECCSCHEME, |